Search Documents

By Stanley F. French

ELECTRICAL power and distribution for the sulphide ore plant is an addition and extension of the existing power system which has served the oxide reduction plant since its inception in 1914. The power plant is located at Tocopilla on the west coast of Chile, some 90 miles from Chuquicamata. A brief description of this plant and the existing transmission system is necessary to an understanding of the problems involved in the provision for the sulphide plant load. Originally the Tocopilla power plant consisted of four Escher Wyss turbines driving Siemens Schuckert generators, each rated 10,000 kw. At various times, units of 10,000 and 20,000 kw were added, all of which operated at 215 psi and 600°F at throttle. In order to improve the economy of the station, a Topping unit was installed in 1938 together with a high-pressure steam generator of 360,000 lb per hr capacity. This unit is rated at 11,000 kw and was designed for 750 psi, 880°F. The exhaust from this turbine passes to the low pressure station header for operation of part of the low pressure turbines. Total kw generated by the high pressure boiler, topping turbine and associated low pressure turbines totals 33,000 kw and the total station capacity is 113,000 kw. This installation proved one of the most successful of its kind, operating almost continuously. The original plant was of German design and consequently European characteristics were incorporated into the system, the frequency being 50 cycles and voltages of 500, 5000 and 100,000 were used for low, generator, and transmission voltages,

Jan 1, 1952

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By Emilio Navarro

XML technology can be used as a standard to transfer information from a relational database to any system that relies on such information. There have been many proprietary methods to perform this information transfer, However, none of them was either able to talk to each other or exchange information in a transparent way. This paper describes a system that will allow for a transparent exchange of information not only between a Web browser and a Web Server but also a stand-alone application and the same Web Server. First, the autor summarize the Internet technologies that support the possibilities. Then the autor outline the tasks needed in order to take advantage of these technologies. Finally, it is suggest a few applications that could take advantage of this system.

Aug 25, 2002

By D. E. Piggott, B. E. Hartmann

The thought of constructing an intake shaft five miles from the shore and 142 feet below the surface of Lake Huron from the bottom up sounds like a questionable venture. Why would one want to raise a shaft from the bottom at the end of a 16 foot diameter, six mile long tunnel to within six feet of the bottom of Lake Huron? The answer lies in the fact that Lake Huron is seldom a tranquil lake. The construction period and workable days from the surface are limited. Two previous attempts to construct this intake shaft by conventional means had been thwarted by lake storms. These approaches were circular sheet-piling cofferdams with the intention of sinking a 30 foot OD, five foot wall thickness concrete casing in the center. However lake storms, particularly in the months of November and December, proved disasterous. The last attempt was halted in December 1970 when three of the seven circular cofferdams on the north side were destroyed by pounding waves. Then, due to the nature of the technical difficulties and limited construction schedule time, it seemed desirable to devise a way in which construction could proceed without being too lake-sensitive. Obviously, if men could work from the tunnel and proceed upward toward the bottom of the lake, not having to worry about the soil collapsing and bringing the lake in on their heads, the construction would be unimpeded by adverse weather. The answer to this, however, required techniques beyond the ordinary. Approximately two years previous to the start of this shaft, nine shafts had been efficiently constructed on the same project site

Jan 1, 1974

In 2007, a total of 7,199 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.4% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Aug 1, 2009

By Jean-François Lapointe

Many advances have been made concerning the automation of heavy equipment teleoperators such as those found in mining. Complete automation, however, is not achieved yet and the operation of these vehicles still relies on the presence of a human operator. Fortunately, a lot of research has been done in order to improve the performance of these human-machine systems. This paper presents the characteristics of different control modes and input devices used for the control interface of those telemanipulators. We describe the benefits and drawbacks of each particular control interface on the overall system performance, based on a review of research in the field. We conclude with some recommendations and a discussion of future research needs, given the new potential advances offered by virtual environment technology and embedded computing.

May 1, 2001

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993

By S. Meng, R. Jin, W. Hu

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II) -activated sphalerite exhibits a high floatability so that satisfactory separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by infrared (IR) spectra; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitution and polymerimtion of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1988

By Rock M. Poulin, Bruce G. Moulton, Daniel E. Nowak, David T. Cass

The Yacambu Irrigation Tunnel Project of 34 km, 5 meter diameter circular and horseshoe section, has been under construction since the early 1970's. Notable among the excavation challenges is high ground cover of 3,000m creating large lithostatic pressures in the tunnel alignment with subsequent plastic flow of the ground in the tunnel walls. The tunnel may converge from small amounts to 1 or more meters of diameter over long sections. Several excavation techniques have been attempted but all without desired results. The paper proposes a new machine concept that uses the history of ground experience as its basis for design.

Jan 1, 1995

By P Paredes, T Leaño, D Gajardo, C Tramón, S Peñaloza

The definition of an ore handling system and its consequent layout design is of crucial importance in cave mining projects. It not only represents the main driver in the production capacity and reliability of the mining system, it is also a fundamental variable in the footprint’s development time and cost.In recent decades, load-haul-dump (LHD) tramming distance optimisation through the allocation of several orepasses inside the footprint has been the most common practice in ore handling system layout definition at Codelco’s operations. Today, the improvement of existing technology, such as higher-capacity LHDs and jaw-gyratory crushers, and intensive preconditioning techniques to improve fragmentation allow the conceptualisation of simple and highly productive ore handling system layouts for wide caving areas that avoid the complexity and high cost of developing numerous orepasses inside the footprint.The initial macroblocks of the Chuquicamata underground mine project (PMCHS) consider an ore handling system layout in which LHDs dump into orepasses located inside the footprint area. The ore is then transferred into crusher chambers located below the production level, where it is crushed by jaw crushers and then conveyed to surface. In an effort to reduce development time and costs, a new ore handling system layout for the PMCHS experimental macroblocks was engineered using improved technologies and techniques in a simpler mining system. This paper compares the new ore handling system layout for the project’s experimental macroblocks with the traditional LHD-orepass layout in terms of production capacity, reliability, development time and cost.CITATION:Paredes, P, Gajardo, D, Leaño, T, Peñaloza, S and Tramón, C, 2016. Simplifying the ore handling system through the use of current technology at Chuquicamata underground mine project, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By David E. Fogelson, James J. Olson

Rock mechanics as a guide to a safe underground operation is gaining importance as more is under- stood of rock behavior under stress and of the competency of rock after blasting. The U. S. Bureau of Mines' Twin Cities Mining Research Center and White Pine Copper Co. personnel undertook a joint research program recently to define how the rock adjacent to a newly opened underground working could be left as undisturbed as possible. The goal was to leave a competent structure which would tend to limit rock falls and thus decrease the incidence of fatalities from this greatest of all underground hazards. High-amplitude stress waves and borehole gases create a crushed zone in the rock, the thickness of which is about equal to the borehole radius. Beyond the crushed zone, additional structural damage occurs to the rock from the microstructural level up to visible fractures that may extend several feet. This type of rock damage near the final excavation lines reduces rock strength and increases the possibility of failure of the openings from subsequent vibrations or stresses.

Jan 9, 1969

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By Rodgers Peale

The Waite mine, as it is locally termed, is situated in the Rouyn district, in the townships of Duprat and Dufresnoy, Quebec, and lies about 340 miles north of Toronto. Due to the impetus given prospecting in the Rouyn district by the discovery, some years ago, of copper-gold ore on the Horne claims, many exploration parties were put into the field. Early in 1925, J. H. C. Waite, C. H. Ackerman, and T. Montgomery staked the claims which now comprise the mine beating their names. Trenching and diamond drilling soon disclosed an ore-body of commercial size and grade, and by the end of 1928 a shaft had been sunk 300 feet and the mine was producing 150 tons of direct-smelting copper ore a day. In the summer of 1925, Dr. H. C. Cooke, of the Geological Survey, made a reconnaissance survey of the property (1), and since that time work of the same nature has been done by several others. MacGregor has published some interesting data on the Amulet mine (2). Using as a background a summer's work on the Horne claims at Noranda, the writer spent the summer of 1929 at the Waite.

Jan 1, 1931

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By James R. Arnold

Over the past few years several commercial wetting agents and drying aids have been tested in the lab and in the plant at Gold Fields Mining's operations at Mesquite and Ortiz. The major goal was to increase recovery with these surfactants by improving the permeability of the pad and increasing the rate of penetration through the rock.

Jan 1, 1988

By Fabien Miller

Automation technologies are increasingly envisaged to improve underground mining productivity. However, the technologies need to be used and adopted gradually in order to get the best benefits. This paper presents the technical and operational aspects of autoguided production vehicles at Brunswick Mine. During 2001 Noranda?s Brunswick Mine has successfully commissioned an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two orepasses. Operational advantages include increased system capacity and enhanced safety and comfort for the operator. The data obtained up to now indicate that the system can operate reliably in mine production

May 1, 2002

By T. F. Witheree

The Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its " bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimensions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz.: Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 71/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3 ; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 224 inches high. Diameter of steam cylinder, 20) inches. } Diameter of blast cylinder, 64 inches. } Stroke 5 feet. The engine is direct-acting horizontal non-condensing. December 26th, 1866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 31/2 feet long x 64 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches; nozzles 21/4 inches diameter. Temperature of blast estimated to be about 500°.

By Matthew Graham, Tapan Goswami, Geoff Brent

In dragline coal mining operations, throw blasting is used for the controlled placement of overburden to maximise coal exposure rates or to minimise overburden removal costs. This may necessitate sacrificing thin coal seams, generally less than one metre in thickness, which are often present in proximity to the main coal seam. This represents not only a significant loss of potential revenue and profit but also a waste of a valuable energy resource.

Jan 1, 2010