Search Documents

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Lorna Ortiz-Soto

A series of titiania- and silica-supported Au, Pt and Pt-Au catalysts prepared through different synthetic routes have been investigated in terms of their structural properties, adsorption of CO, and catalytic activity for the selective catalytic reduction of NO by propylene and the oxidation of and CO. Catalysts prepared by incipient wetness impregnation from individual Pt and Au precursors, exhibited characteristics very similar to those of monometallic Pt catalysts. This behavior is consistent with a model in which the two metals remain segregated due to their miscibility gap, and only Pt participates in the adsorption of CO and the reactions under consideration. In contrast, catalysts prepared from a Pt2Au4(C=CtBu)8 organo-bimetallic cluster precursor exhibited different behavior both in terms of CO adsorption and their catalytic activity for the three reactions examined. The combination of the kinetic, spectroscopic and structural characterization data suggests that in this case Pt and Au remain intimately mixed in the form of Pt-Au bimetallic particles, and that the presence of Au modifies the behavior of Pt.

Oct 1, 2003

By N. K. Davé

Water quality impacts of shallow water submersion of partially weathered and oxidized waste rock containing reactive sulphide minerals were investigated in laboratory column lysimeter studies. The waste rock investigated was highly reactive, contained oxidation reaction products from previous exposure and weathering, and had a low sulphur content of approximately 2 % S, mostly as pyrite. The submerged waste rock, though previously weathered, had high oxygen consumption, resulting in rapid depletion of dissolved oxygen in its pore water, within a shallow depth of ~2?5 cm from the surface. The surface and pore water qualities of the submerged waste rock were significantly impacted by the dissolution and release of previous-oxidation-reaction products, which contributed to their rapid acidification and having increased concentrations of dissolved SO4, Fe total and other metals: Al, Mn, Ca, Cu, Ni, Zn and Pb. Despite the high porosity and permeability of the waste rock, the diffusion controlled mass transfer from the submerged waste rock to the overlying water cover was relatively low for most ionic species. Additional surface oxidation of the sub-merged, partially weathered waste rock was on-going, but its impact on the overall surface water quality was low and masked by the dissolution and release of previous oxidation reaction products to both surface and pore water regimes.

Jan 1, 2006

Through the courtesy of Mr. J. H. Batcheller, we are able to give the following extracts from a letter written by Mr. Caetani: It has been a nice idea of yours to collect for me all those scraps of news I received a few days ago and to send me such a long interesting letter. In four years war I have had practically no news. Burch wrote several times but several of his letters were lost and so mine. I believe I even wrote to you. Much has changed since our last days in Telluride; here and there many have disappeared. Of myself I will tell you in a few words: for a year I was in Cadore(?), where I had the good luck to do to the others what they wished to do to me, and had good luck on my side. Then I went to Macedonia for 5 months, did little fighting but lost my faithful fellow officer and companion.

Jan 6, 1919

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By M. L. Torem, R. H. Rojas, A. G. Merma

"Fine particle recovery by conventional flotation processes is very low mainly due to the low probability of bubble/particle collision and adhesion. In order to solve the problem of low particle recovery, several flotation technologies have been developed to increase bubble/particle collision efficiency. Among these technologies, the electroflotation process stands out. This process has advantages in the generation of microbubbles (<100 µm) and in the production of different amounts of hydrogen and oxygen microbubbles. These advantages favorably influence the fine particle floatability, due to the greater probability of particle/bubble collision and adhesion. The electroflotation tests were conducted for a hematite/sodium oleate system in a Partridge-Smith modified electroflotation binary cell of 0.38 L usable volume. The sodium oleate concentration, particle size, pH and current density were evaluated. Satisfactory results in the recovery of hematite were found at pH values of 7, reaching hematite floatability of 99% and 90% with hydrogen and oxygen bubbles, respectively.INTRODUCTIONThe flotation recovery of fine and ultrafine particles is normally very low and is caused by several factors, among them, the low probability of collision and adhesion bubble-particle, the difficulty to overcome the energy barrier (entrainment and entrapment), low selectivity, surface oxidation and mineralogical changes (Schulze et al., 1989; Waters et al., 2008; Shahbazi et al., 2010). This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However, it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. Electroflotation is one of the variants of the flotation process, where the gaseous phase is produced by electrolysis of an aqueous solution, generating oxygen and hydrogen bubbles (Sarkar, 2010; Gupta and Ali, 2012). These smaller size bubbles allow the recovery of fine particles by increasing the collision efficiency. This process is versatile and competitive in relation to other techniques such as dissolved air flotation and dispersed air flotation because the electroflotation units are smaller, more compact and require less maintenance and less operating cost than other flotation units (Zouboulis and Matis, 1995,). In addition, the electroflotation process is a clean technique and provides results in a short time, requiring only the investment in the electroflotation cell construction stage and the choice of the electrodes (Ketkar et al., 1991; Sarkar et al., 2010; Sun et al., 2011). In this sense, this study assesses the effect of pH, particle size and sodium oleate concentration on electroflotation of hematite fines."

Jan 1, 2018

By Francisco. Grimaldo Z

El presente texto señala la ejecución del proyecto de explotación de taladros largos por paneles con relleno cementado (TLPC) en la Mina Cerro de Pasco a través de la explotación de paneles y la técnica de perforación de taladros largos, donde se pueda explotar cuerpos, cuyas condiciones geomecánicas no cumplen con los requerimientos para una explotación de subniveles clásicos. Asimismo se puede aplicar en mineral con cajas tipo I, II y III utilizando los paneles verticales con relleno cementado y lama. El objetivo es elaborar un muro de sostenimiento que cumpla los requerimientos de resistencia de compresión y tracción que reemplace las cajas, permitiendo así la explotación por taladros largos verticales de los paneles centrales en forma secuencial.

Jul 31, 2003

By S. Painter

The effects of forced ventilation and thermal radiation in open drifts are included in three-dimensional thermal hydrology simulations of a potential waste repository at Yucca Mountain, Nevada. A semi-analytical model is used to calculate the amount of waste heat removed by ventilation air during each time step of the multiphase thermal-hydrology simulator. The model accounts for thermal radiation and changes in air temperature and humidity along the emplacement drifts. The fraction of heat removed by ventilation is time and position dependent.

Jan 1, 2004

By E. V. Koporulina, I. Zh. Bunin, M. V. Ryazantseva

"We studied the mechanism of structural and chemical transformations of columbite, tantalite, zircon and feldspar surface during the treatment by high – power electromagnetic pulses (HPEMP) using the methods of X - ray photoelectron spectroscopy (XPS), analytical electron microscopy (SEM - EDX), Kelvin probe force microscopy and flotation experiments. According to XPS and SEM - EDX data, major changes in the atoms chemical state of investigated minerals surface are related with formation and modification of functional cover and changing in concentration (% at.) of hydroxyl groups on the mineral surface, leading to increase in the contrast of technological properties of the rare metals minerals. Research has identified the optimal parameters of HPEMP - treatment of rare - earth minerals Npuls ??104, Ttreatment ??100 sec. improving the selectivity of the flotation separation of columbite and zircon. The difference in mineral recovery into the froth (? e) before and after HPEMP - treatment was about 11 % and 24.5 %, respectively. No significant increase was observed in the flotation activity of feldspar. This study's findings demonstrate the effectiveness of HPEMP - treatment in inducing a controlled change in the structural and chemical properties of rare - earth minerals and improving the process efficiency for the processing of rougher tantalum - niobium gravity concentrates.INTRODUCTIONThe importance of improving the processing methods of tantalum-niobium ores and concentrates is explained by the mineralogical properties of rare - earth ores. These are properties such as the variable mineral, chemical, and grain size composition, complex morphometric properties, and the dissemination of ore mineral grains of micro - and nanometric size. Iron oxide and hydroxide films on the mineral surfaces neutralize the surface physicochemical and absorption properties of the minerals. Both in Russia and globally, nonconventional (non - mechanical) methods are being developed based on physicochemical, electrochemical, and pulsed energy impacts to improve the efficiency of disintegration and liberation processes of disseminated mineral complexes and to enhance the contrast of the structural, chemical, and technological (floatability) properties of refractory ores. This study is devoted to the investigation of the applicability of high – power electromagnetic pulses (HPEMP – treatment) for the change in the structural and chemical properties of rare - earth minerals and improving of the flotation properties contrast."

Jan 1, 2018

By M. Tomita

One of the most essential factors for a custom smelter to strengthen its competitive power is to Improve its comparative standing in purchase of concentrates from the world market. It is especially critical for Japanese smelters who depend almost 90% of their raw materials on import. In order to accomplish this breakthrough, the development of the new technology which enables us to treat concentrates containing higher Impurities is inevitable. Nippon Mining Company Ltd. made an intensive research on processing complex ore for three years from 1979, and successfully developed an original hydrometallurgical process to treat converter dust for eliminating impurities from the copper smelting circuit. The commercial plant was constructed at the Saganoseki Smelter & Refinery in 1982, and its nine years operation has been satisfactorily proven the advantages of the technology. The concept of this process and its operational performance are discussed.

Jan 1, 1992

By B. Peszko

There are many measuring methods of grain sizes. Taking into consideration the fine grained materials, one of the existing techniques is measurement of grain size by the Coulter Counter method. This method is based on the measuring the changes of electrolyte resistance during grains flow through the calibrated diaphragm. This method is relatively simple to apply, significantly precise and the results are given quickly. However, the problem is that the measurements are limited by the size of diaphragm. Because of this situation, measurement of grain sizes by this instrument is possible in range from 10% to 60% of diaphragm diameter. This limitation causes the necessity of re-placing diaphragm in case when the measured grain size distribution concerns the material of large size range. In purpose of determining the total grain size distribution, the synthesis of some partial distributions, given for individual grain fractions (with different diaphragm applied), is required. This is possible to do by calculating the mixture of distribution functions, created from the partial distribution functions. Two materials were selected to research: quartzite and glass, which were comminuted in cylindrical crusher, additionally grinded, screened and then analyzed by Coulter Counter for five grain fractions: 0~125 µm, 0~80 µm, 0~56 µm, 0~40 µm and 0~25 µm. For each fraction, five different partial distributions were given (in case of glass ? four), which are the basis for the creating the joined grain composition. To assure the adequacy of the given distribution function, it is necessary to obtain the possibly best approximation of partial distributions. In the work, both the parametric and non-parametric methods of density approximations of investigated random variable. For each grain fraction the approximations were done by three traditional distribution functions: RRB, GSA and log-norm distribution functions and three methods of non-parametric approximation: Gauss kernel, Epanechnikov kernel and orthogonal Fourier series method. As the criterion of the certain distribution function acceptance, the value of the residual deviation was assumed, given by the formulae:

Jan 1, 2014

By E. G. Noble

The effects of HBr concentration and temperature on the solubility and hydration state of AlBr3,&apos; CoBr2, PbBr2, MnBr2, KBr, and NaBr were investigated by the Bureau of Mines. Saturated aqueous solutions of the AI, Pb, K, and Na bromides were sparged with HBr gas at 20°, 40°, and 60° C, and saturated solutions of Co and Mn bromides were sparged at 20° C. Increased HBr concentration caused decreased salt solubility because of the common ion effect for all the investigated bromides except PbBr2. Aqueous solubilities at 20° C were, in percent, 51.7 for AlBr3, 53.2 for CoBr2, 1.1 for PbBr2, 59.6 for MnBr2&apos; 39.5 for KBr, and 47.4 for NaBr. At 60° C, the solubilities were, in percent, 53.3 for AlBr3, 2.2 for PbBr2&apos; 46.0 for KBr, and 53.8 for NaBr. Solubilities in solutions sparged to HBr saturation at 20° C were, in percent, 0.5 for AlBr3, 42.0 for CoBr2, 32.2 for PbBr2, 21.0 for MnBr2, 0.6 for KBr, and 0.3 for NaBr. At 60° C, the solubilities at HBr saturation were, in percent, 1.8 for AlBr3, 41.4 for PbBr2, 1.3 for KBr, and 0.4 for NaBr. CoBr2 precipitated out to a minimum solubility of 27.2 pct at 28.7-pct-HBr concentration. Further increases in HBr concentration increased CoBr2 solubility because of the formation of bromide complexes. PbBr2 in-creased in solubility as HBr concentration increased.

Jan 1, 1988

By H. W. Graham

[ ] Even though we have a small audience, I am sure there are some here who are interested in sponge iron. It is a large subject, with a lot of economic interest, and one that will continue to grow in importance as the years go by and as the conditions that urge action in that direction increase. The authors have chosen to deal in this paper with one particular narrow phase of a long program of work by the Bureau of Mines. Before asking for any general discussion, I would myself like to ask Mr. Buehl if he would tell us just a little bit about the mechanism of discharge and the form in which the material was discharged; that is, when dolomite is added, what happens to the dolomite? R. C. Buehl (author&apos;s reply)-You are interested in the equipment that was used? H. W. GRAHAM-No, just the product. R. C. Buehl-The product was in granular form, of a shape very similar to that of the ore used. Using minus 10-mesh ore, the product is essentially minus 10-mesh, mixed with the coal and dolomite. It is then passed through a belt type of magnetic separator, which picks up the magnetic iron and allows the dolomite and coal to fall off. If the coal is sufficiently valuable, it can be separated from the dolomite and, provided the coal has a sufficiently low ash content, it can be reused. For instance, if a low-ash reducing agent like petroleum coke is used, it can be reused until all the carbon is consumed. H. W. Graham-That clears the point for me. I was not quite sure whether the experi-

Jan 1, 1947

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

By Ludwig Schmidt

Investigations conducted by the Bureau of Dines pertaining to the reduction of evaporation losses of petroleum have shown that such losses may be reduced 70 to 80 per cent by the use of vapor-tight tanks equipped with vacuum and pressure relief valves, and vapor-tight thief hitches. Additional studies have shown that it is often economical to supplement this type of construction with other measures that will reduce evaporation losses still further. Water-cooling systems, insulation, and light colored paints are the measures most often used in connection with vapor-tight tanks. Painting with light colored paints probably is employed in the greater number of cases. On account of the cost of insulation, or of installing water cooling systems, the use of these methods are restricted to tanks containing gasoline or crude petroleum with a very large content of low-boiling fractions. The effect of cooling systems has been discussed in a previous report.2 In choosing paints for tanks many factors must be considered. Probably the three most important are cost, protective value, and color. Many companies have adopted a standard color for all of their tanks in this way they reduce the initial cost of paint by buying in large quantities. The tank farms of such companies usually have a neat appearance, resulting from the uniform painting of all tanks. This procedure also has advertising value. Unfortunately, most of the paints used to protect steel are of the darker colors, usually red or black. These colors accelerate the rate of evaporation. Several companies have solved this difficulty by using a dark colored metal-protective paint as a primer coat, and a paint of any desired color for the final coat. Special metal-protective primers to be used under light-colored cover coats have been placed on the market by several paint manufacturing companies.

Jan 1, 1925

By J. H. Wernick, S. Geller

A number of new AB, compounds, in which A is a rare earth or yttrium atom and B is Al, Mn, Fe, Co, or Ni, having the cubic MgCu, structure (Laves phase) are reported. In most of the compounds, the interatomic distances are normal; the lanthanide contraction is observed. However, in the compounds CeB2, B = Fe, Co, Ni, Ce appears to have a valence substantially greater than three; in CeAl2, Ce appears to be trivalent. These results are interpreted as vesulting from an energetically more favorable situation for the 4f electron of Ce to be lost to the 3d band of Fe, Co, nnd Ni. Evidence for the existence of homogeneitj! ranges in these compounds is presented. THE purpose of this paper is to report on the crys-tallographic investigations of a large number of new compounds, Table I, with the MgCuz structure (cubic Laves phase). It is a part of a continuing study of the magnetic properties and structures of binary systems involving the rare earths. In a previous paper&apos; some of the magnetic properties of such systems were reported briefly. We have also reported2 a number of compounds of the CusCa type. The compounds were prepared by induction melting in Argon atmosphere of mixtures of stoichiomet-ric amounts of the constituent elements.* For most of the compounds fused alumina or silica crucibles were used as the containing vessel; graphite crucibles were used to prepare CeA12, NdAl2 and TbA12. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis-type Norelco cameras of 114.6 mm diam. The compounds AB2 belong to space group Fd3m-Ol with 8A in a): (000; 01/2 &apos;/2;3) + 000-; b % XA and 16B in dl: (000; oVa %; 3) + 5/87; % %; 7e % Vs\£>. Because the intensities of the reflections on the powder photographs of the different compounds are similar, relative intensities were computed only for DyMnz for CrKa radiation, Table 11. In the calculation of intensities, the Thomas and umeda3 atomic scattering factors, corrected for dispersion,4 were used. The agreement between observed and calculated intensities leaves little doubt that DyMnz has the MgCuz structure. Crystallographic data for the ABz compounds are given in Table JII. Twelve of these compounds have been reported by other authors. A comparison of the published results with our work is given in Table W.* ers of elements of lower purity, to peritectic reactions in some cases, and to the presence of homogeneity ranges in these alloys, so that melting losses would still result in single phase alloys. The possibility of existence of homogeneity ranges in these compounds was investigated systematically only for GdMnz. At room temperature, the solid solution range is between

Jan 1, 1961

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By J. E. Schiller, S. E. Khalafalla

Due to its unique surface properties, magnesium oxide (MgO) is an excellent medium to filter asbestos and other suspended solids from water. MgO operates up to twice as long as a sand filter before backwashing is required while flow rate and filtrate clarity are as good or better with MgO.

Jan 1, 1984

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By G. Roy

Interest in metal-hydrogen systems can be manifold. Small amounts of hydrogen adsorbed by elemental metals and alloys usually result in strong changes in the physical and mechanical properties of engineering materials. Overwhelmingly, these changes, viz. hydrogen embrittlement, are considered deleterious with respect to structural performance of engineering materials. However, the changes, often studied by metallurgists and metal physicists, can present new possibilities and applications. A prominent example is the recent interest in safe, solid-state hydrogen storage in metallic lattices. In a new laboratory in MTL, Ottawa, a study has been initiated to investigate the effect of "micro- and macro- alloying" of Al and Mg powders with hydrogen (in high-energy mechanical alloying mills) on plastic deformation in metal and metal hydride structures. It is anticipated that high-rate impacting and subsequent grain refinement in the mill will have an effect on hydrogen storage capacity in lightweight magnesium and aluminum alloys. First examination of the state-of-stress by X-ray diffraction in high-rate milled, nanostructured pure aluminum, aluminum milled with a solid surfactant, and aluminum or magnesium alloy milled with hydride and/or gas hydrogen will be presented.

Jan 1, 2005