Search Documents

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By Anne Kvithyld

Silicon solar cells, that convert the energy of sunlight into electric energy, are attractive sources of energy. In the production line wafers of solar cells are sliced from a multicrystaline ingot solidified unidirectionally. Recycling scrap from top and sides of such ingots is addressed. SiC and Si3N4 inclusions are a major problem. Scrap from Scan Wafer ASA is melted in a high vacuum furnace at around 1500ºC. The filters, from commercial producers, are C and SiC with 10, 20 and 30 ppi. Characterisation of inclusions before and after filtration, and in the filter itself, is performed by microscopy. Dissolution of silicon in acid and counting of the un-dissolved inclusions is also carried out. In the filter Si3N4 needles and SiC inclusions were identified. The amount of these inclusions in the filtered silicon is much less than in the input. In conclusion, filtration using SiC and C filters in vacuum system in argon atmosphere removes SiC and Si3N4 inclusions from solar cell scrap. Flow of metal through the filters is not a problem. These results are promising with scale-up to industrial application in mind.

Jan 1, 2006

National Society of Professional Engineers has thrown its full sup- port behind pending legislation to appropriate $500 million for national conversion efforts that would provide employment opportunities for engineers, scientists, and technicians who are currently unemployed because of the decline in defense and aerospace programs. Known as the Davis-Giaimo bill, the proposed legislation would raise total Federal investment in science and technology to an adequate annual spending level and keep it proportionally equal to the growth in the GNP. If passed, the bill would increase and maintain Federal obligations for civilian-oriented research and development activities to a parity level with similar obligations for defense research development. U. S. Bureau of Mines has cataloged and placed on open file an inventory of U.S. coal deposits which can be economically strip mined at today's production costs. The costs include charges for reclaiming the mined land as required by 21 states. The report claims that some 46 billion tons of bituminous coal and lignite can be strip mined under present economic conditions, and that 32 billion tons of the total is classified as having less than 1% S. The report reviews strippable coal deposits by state, by county, by coal seam, by coal-seam thickness and by sulfur content. The report also gives an up-to-date summary of state laws on surface mine reclamation. Open-file copies of "Strippable Reserves of Bituminous Coal and Lignite in the U.S." may be consulted in Washington, D.C., at the Department of the Interior library and at U.S. Bureau of Mines offices in Pittsburgh, Denver, San Francisco. Dallas. Spokane, and Douglas Island, Juneau. Alaska.

Jan 1, 1971

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

By D. M. Bastidas

The reduction of copper sulfide and copper oxides originated during artificial tarnishing of copper was studied using potentiodynamic potential/current density experiments. Six copper surface treatments were considered: mechanical polishing; indoor exposure for 7 days; chemical etching in 1.6 M nitric acid; chemical etching and heating at 160°C; and chemical etching and dipping in a 9x10-4 M or 0.9 M potassium sulfide (1(25) solution at 70°C. Cuprite (Cu20) and chalcocite (Cu2S) were the main compounds formed. A linear relationship with the square root of the scan rate (v) was obtained by plotting the potentiodynamic potential/current density for the tarnish dissolution processes. A relationship between potential and current density cathodic peaks was not obtained, according to Müller's model, showing a proportionality factor with the dimensions of a resistance.

Jan 1, 2007

By Schonert K

The throughput of a HP-roller mill is determined by the acceleration of the feed material within acceleration zone and introduction into the compression zone. Both processes depend on the internal friction and the friction of the material on the roller surface which is influenced by the surface structure and adhering of material. The particle motion in the acceleration zone has been investigated with high speed videos showing the effect of the centrifugal force and the slip on the roller surface. The throughput is discussed in the term of the specific throughput which can be approximated by a linear function characterised by the throughput number and the throughput elasticity. The throughput number is a helpful measure for investigating the influence of the feed material and the surface structure. The experimental results give some guidance for chosing an optimum corrugation profile.

Jan 1, 1993

By J. Hebert, J. Donnelli, J. Sedey

Installation of a Load Commutated Inverter (LCI) provides an economical method for conversion of a Fixed Speed Semi-Autogenous Grinding Mill into one with variable speed, qualities. Though capital intensive, the conversion appears to be one of the most cost-effective methods to gain the advantage of critical speed variations for variable ore characteristics. Expected advantages from the installation of LCI drives at the Goldstrike Mine were decreased liner wear, decreased media consumption and additional grind for increased production rates. These issues as well as construction, economics and performance will be discussed in the presentation. The utilization of the existing equipment came to play an integral part of the study and economic justification of the overall project.

Jan 1, 1999

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By G. Gregory Bryan

G. GREGORY BRYAN 33.1-DEFINITIONS 1. Engineering-Engineering may be defined simply as the science and art of making materials and energy serve the purposes of mankind. There are many fields of engineering, each with specialized branches. The basic fields are: civil, mechanical, electrical and chemical. Others may be specialized phases of one of these or a combination of two or more of them. Mining engineering, for example, requires a working knowledge of construction, mechanics, electricity, metallurgy, geology, accounting and economics, in addition to mining techniques or methods. Mining geology and geological engineering involve rocks and their structure and the forces that act upon them, and chemistry, physics and mechanics also are important to practitioners in these fields. Metallurgical engineering requires chemistry and physics but also a working knowledge of mechanics and electricity. The fields of engineering with which this section are concerned are those primarily involved in the finding, mining, processing and utilization of the natural mineral resources of the earth. They include geology, mining engineering and metallurgy, each with several specialized subdivisions. 2. The Engineer-The engineer is an individual who has had specialized training to qualify him to practice the profession of engineering. The term engineer is used here in its broadest sense to include such professions as certain applied branches of geology, physics and chemistry, whose practitioners may not have acquired engineering degrees but who, nevertheless, by training and experience in some area of the minerals industry, qualify under the above definition. To become a successful engineer, a person should have certain pronounced aptitudes and preferences, even before embarking upon the requisite course of training. Among the chief qualifications that the engineer-to-he must possess are: (a) a natural inclination toward mathematics and the physical sciences, and (b) intellectual and moral honesty. Among the qualities the student engineer must develop are: (a) independence of thought, open-mindedness, sound judgment and the ability to observe, deduce, plan and apply solutions, (b) the ability to articulate and convince, and (c) the ability to organize and direct the activity of others. These qualities are normally developed through sound education, followed by pro¬gressive experience. 3. The Consulting Engineer-The consulting engineer is an engineer primarily in the business of furnishing specialized advice and engineering services on an intermit¬tent, part-time or occasional basis to clients who do not have continuous or full-time need for those services. He must be able to make and take full responsibility for decisions and recom¬mendations where original thought is required. He should not be confused with the engineer, surveyor or technician who also may furnish services on an intermittent basis, such as regular periodic surveys, the overseeing of drilling programs and other such routine work as may require little original thought and planning. 33.2-THE PROFESSION OF CONSULTING ENGINEERING 33.2.1- QUALITIES REQUIRED A successful consulting engineer must first have, as a minimum, the qualities and preparation of an engineer. In addition, he must have sufficient knowledge,

Jan 1, 1973

By Mark Tsirlin

Kinetics of the initial oxidation stages of diffusive silicide coatings on 8 molybdenum and niobium at 1100 - 1700 and under the pressure of 400 and 1330 Pa has been studied using methods of gravimetry and gas phase analysis of oxygen, as well as by SEK, XRD and EDMA methods. The first oxidation stage described by asymptotic equation in case of NbSi coating changed over to the stage described by parabolic equation. The asymptotic law was shown to depend on non - stationary conditions on the oxide layer boundaries. Interconnection between silicides and quartz structures, on the one hand, and peculiarities of oxidation kinetics, on the other, is [discussed. The possibility of estimation oxygen atom jump frequency in quartz and fractions of oxygen reacting with metal and with silicon proceeding from the analysis of the kinetic data was ascertained. Conditions of oxidation kine- tics transfer from asymptotic (or parabolic) stage to a non - protective "linear" stage, associated with volatile ~roduct formation, are also discussed.

Jan 1, 1995

By Gordon M. Elliott

Health risk underlies all of today's environmental regulations. Mine Manager's are no strangers to risk, but risk in the context of mine management is not the same as risk in the context of environmental regulation. One of the risks facing the mine manager is whether the mining operations meet environmental compliance standards. These standards are defined in terms of the frequency of occurrence of adverse health effects in an exposed population (i.e., health risk). Demonstration of compliance necessarily involves mathematical modelling and selection of values for input variables. What is not immediately apparent is that the method of estimating the human health risk has a significant influence on remedy selection and the amount of money spent at suspected contaminated sites. Using a hypothetical, mining-related example, this paper illustrates the disassociation between the current deterministic approach to health risk assessment and cost-effective decision making. This paper also illustrates how the probabilistic approach to health risk assessment provides a more realistic characterization of health risk and enables mine managers to identify cost-effective remedial strategies for the site.

Jan 1, 1992

By H. V. Churchill

There are two distinct methods of combating corrosive conditions. The first and most popular method is to choose a surface or material which will give adequate service under the specific and general conditions which are present. The second is a control or modification of the corrosive conditions to the end that metals and materials which would be attacked and corroded without such control or modification may be used. Under the first method of attack of the corrosion problem may be grouped such devices as the selection of metals or alloys which offer great resistance or the use of protective coatings such as paints, lacquers or metallic coatings. Such procedures are exceedingly useful. It is undoubtedly true that most of the problems of corrosion will be solved by recourse to this first method of attack. However, it must be remembered that there are many conditions in which metals are used where the choice of the particular metal to be used must depend upon other factors than corrosion behavior. Some of the factors which may govern the selection of metals for specific use are the physical and mechanical properties of the metals. But there is another factor which is of prime importance and that is relative price. It is the pressure of these factors of mechanical properties, physical characteristics, and relative price that has acted as the stimulus for the second methhod of combating corrosion. The producer and user of various metals is confronted with the fact that because of mechanical properties, physical characteristics, or price, the use of a particular metal is desirable even though the corrosion conditions are adverse to the use of the metal. In many cases, the successful use of the metal may be made even though it is impossible to protect the metal by coatings. This is rendered possible by control or modification of the corrosive media. Use of Sodium Silicate to Prevent Attack by Alkali Solutions This idea of controlling or modifying corrosive media is well illustrated by some recent experiences with aluminum. For a number of years collapsible tubes have been made of aluminum. Due to the ease with which aluminum is attacked by even mild alkalies, the use of such tubes

Jan 1, 1929

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By X. Grant Chen, A. R. Farkoosh, M. Pekguleryuz

Nano-scale Al-(Fe,Mo)-Si dispersoids form during solution treatment in grain interiors (intradendritic regions) of cast Al7Si0.5Cu0.3Mg alloyed with 0.3Mo (wt.%). Unlike the Q-Al5Cu2Mg8Si6 and ?-Al2Cu age-hardening precipitates which coarsen resulting in loss of strength in Al-Si-Cu-Mg alloys, these Mo-containing dispersoids are thermally stable and retain their strengthening effect at elevated temperatures. Consequently, the age-hardened Al7Si0.5Cu0.3Mg0.3Mo (wt.%) exhibits high strength and creep resistance at 300 °C.

Jan 1, 2014

By José Luis Calderón, Percy Arrosquipa

Compañía Minera Poderosa ha identificado una interesante oportunidad de generar valor y de mejorar tanto el clima laboral como el de relaciones comunitarias mediante el proyecto descrito en este artículo. El proyecto se orientó a motivar la incorporación de prácticas de responsabilidad social, tanto entre proveedores de bienes y servicios, como entre empresarios mineros artesanales en proceso de formalización. Como ejemplo, se analiza el caso del cofinanciamiento de la obra “Mejoramiento del sistema de agua para consumo humano del anexo Pueblo Nuevo”, que benefició a 195 familias con un servicio de agua de calidad las 24 horas del día. De este modo, se corrigió una fuente de conflictos sociales y se materializó una alianza para el desarrollo local entre la mediana minería y la minería artesanal. Por su parte, Asociación Pataz entregó certificados de donación, deducibles del Impuesto a la Renta, a los aportantes.

Sep 30, 2017

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By Earl S. Greiner, Eric R. Jette

The literalure on the binary alloys of iron and silicon has been reviewed by Stoughton and Greiner.1 Another even more extensive and detailed survey of the present knowledge has been prepared under the auspices of the Alloys of Iron Research Committee by Greiner, Marsh and Stoughton. Since the latter surrey has already been issued in its preliminary form, it will be unnecessary to review the literature in the present article. However, in this connection there should be noted the important work on the crystal structures of the iron-silicon alloys by Phragmén,2 who investigated the entire system, identified the various phases and determined the homogeneity ranges of these phases. It was evident in the surveys cited above that in the range from 0 to 15 per cent silicon, which includes the commercially most important, alloys, the results obtained by thermal analysis, microscopic examination and the determination of electrical, magnetic and mechanical properties were extremely confusing. From time to time various compounds between iron and silicon have been postulated to account for the results yielded by the classical methods, and much argument has ensued. It was presumed that if compounds occurred which are sufficiently diverse in their properties to account for the characteristics of the alloys, they should be recognizable as separate phases but satisfactory proof of this sort has not been found by thermal or microscopic methods. Contributing to the confusion is the fact that the electrical, the magnetic and some of the mechanical properties are "structure sensit'ive"; i. e., they are influenced to a marked degree by the presence of minute amounts of impurities, the specific characters of these impurities, the grain size, the character of the grain boundaries, small general or local strains, etc. Thus interpretations of the discontinuities in the various property versus composition curves that identified these discontinuities with phase changes or compound formation have always been open to question.

Jan 1, 1933