Search Documents

By R. V. Ramani, R. M. Mishra, Y. J. Wang

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solution. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning. Starting from an initial system with no leakage and one fan, more complex ventilation networks with several leakages, sections and fans, are analyzed to show that ventilation system design on the basis of total systems approach is the correct procedure.

Jan 1, 1979

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By Raymond A. Povirk, David L. Bartsch, James V. Hamel

The Ohio Valley Coal Company is expand- ing its Powhatan Mine No. 6 near Alledonia, Ohio. This expansion includes a 20 rn (65 ft) height in crease for an existing 44 rn (145 ft) coal refuse - slurry impoundment dam. The dam is being raised by upstream construction which will involve placement of more than 15 m (50 ft) of new fill over an existing reinforced concrete decant structure. This structure is 0.76 rn (30 in.) square inside and its deepest portion was under 24 m (80 ft) of coal slurry and water. The top of the decant structure was not strong enough to safely support the new fill and, because of the slurry and water, there was no way to reinforce the structure from the outside. The structure was reinforced frorn the inside by sliplining 73 m (240 ft) of 0.66 rn (26 in.) OD, 0.53 rn (21 in.) ID polyethylene pipe, grouting around this pipe with cellular concrete. and constructing a steel-fiber reinforced micro-silica concrete transition at the upslope end of the pipe. Rehabilition of the decant structure was completed in August 1989. The rehabilitated decant structure is now performing satisfactorily as fill is being placed over it for raising the dam.

Jan 1, 1991

Economic recovery of valuable natural resources is enhanced through an integrated approach to establishing and operating the mine.Gordonstone has a unique and valuable high quality coal and the basic aim for the mine is to satisfy customers through high standards of safety, productivity and reliability and genuine regard for its people.Gordonstone defined its main resources available for recovery of its natural resource and has designed and built facilities which display technical and engineering excellence.But to build a world class mine Gordonstone recognised the need to take a large- step beyond relying on technical excellence. In designing Gordonstone mine all aspects of coal mining were treated as part of an integrated process.This paper will explain the route Gordonstone has taken and will continue to take into the future in using an integrated approach to mining.

Jan 1, 1993

By Himaki Nakano, Kenji Hara, Toshiaki Tsuru, Shunsuke Kawano, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition of Fe-Ni and Zn-Ni alloys from aqueous solutions is one of the well-known examples of anomalous codeposition in which less noble metal deposits preferentially. In this paper, the electrodeposition behavior of these alloy systems was compared between the methanol and aqueous baths. In Fe-Ni system, the significant suppression of the deposition rate of more noble Ni was observed over a wide range of electrolysis conditions in both methanol and aqueous baths. However, the electrodeposition of Zn-Ni alloys showed the typical feature of normal type codeposition in the methanol baths, which was completely different from that in aqueous sulfate baths. The difference in the electrodeposition mechanism between Fe-Ni and Zn-Ni alloys was discussed on the basis of the alloy deposition behavior in the baths in which the activity of water was varied:INTRODUCTION'It has been well known that Fe-Ni alloys show an excellent soft magnetic property. Therefore, thin films of this alloy have been used to fabricate the'-various magnetic devices. For the production of Fe-Ni thin films, dry processes such as sputtering, PVD and CVD are 'employed frequently and the resulting films showed a preferable property as a magnetic material. Electrolyses as a production technique of thin films, on the other hand, has the advantage over other processes in its cheaper production cost due to the simplicity of the production unit The Zn-iron-group metal alloys such as Zn-Ni and Zn-Fe electrodeposited on a steel sheet ale known to exhibit excellent corrosion resistance and therefore the electrodeposition of these, alloys has been applied to the production of surface treated steel sheets mainly for automotive body panels.According to Brenner (1), the electrodeposition behavior of Fe-Ni and Zn-Ni alloys was' classified into the' 'anomalous type. In this type of codeposition, less noble metal, i.e. Fe for Fe-Ni and Zn for Zn-Ni system, deposits preferentially and the change in -the alloy composition- with the variation of electrolysis conditions was unpredictable because of their obscure deposition mechanism. Since most properties of the alloys mainly depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is neces5al)' to clarify the mechanism of anomalous codepasition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so fur, and among them the hydroxide .suppression mechanism (2), (3) has been regarded most plauslble depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is necessary to clarify the mechanism of anomalous codeposition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so far, and among them the hydroxide suppression mechanism (2), (3) has been regarded most plausible. According to this mechanism, it can be predicted that the codeposition behavior depends greatly on the characteristic of water solvent in this study, using methanol as a solvent, the electrodeposition behavior of the anomalous codeposition was investigated to discuss the validity of the hydroxide suppression mechanism."

Jan 1, 2000

By John W. Brown

The purpose of this paper is to describe different methods of evaluating the performance of your current rotary blast hole drills. To properly evaluate a drill rig's performance you should include a competent driller, mechanic, rotary bit technician and a technician representing the manufacturer of the drill.

Jan 1, 1998

By Moritz P

Thiourea has been recognised for a long time as an acid-stable complexant for gold. Generally, the use of thiourea has been shown to exhibit enhanced leaching kinetics compared to cyanide but suffers the disadvantage of excessive reagent consumption. Thiourea leaching is particularly com- patible with the extraction of gold from refractory ores. This is due to the need for an oxidative pretreatment to liberate the gold. Such pretreatments typically result in the production of an acidic residue. The application of novel thiourea leaching technologies to the extraction of gold from a bioleached pyrite concentrate was investigated. The interac- tion of leach variables with thiourea consumption and gold extraction was established. An economic assessment of thiourea leaching was compared with conventional cyanidation. The results indicated that gold leaching of the bioleached residue using thiourea compared very favourably with cyanidation.

Jan 1, 1991

By A Giblett, R Dunne, D Appelhans

There are a number of hurdles that must be negotiated in order to design an effective gold ore treatment facility such that the expectations forming the basis of project economics are valid and can be achieved in practice. Selecting samples based on geometallurgical context, performing and interpreting testwork relevant to the selected process flowsheet are essential considerations towards achieving this aim. This paper discusses recent experiences in process development for free milling gold ores giving consideration to frequently encountered challenges of this nature.CITATION:Giblett, A, Appelhans, D and Dunne, R, 2013. Considerations for effective gold process development, in Proceedings MetPlant 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By C. Rutledge

The new mining method of multiple strata blasting, called StratablastTM, is described in a separate paper presented at this conference. The current paper presents three case studies where the technique was implemented in three different configurations in large-scale blasts in Australia. The first two blasts were in the Hunter Valley of NSW while the third was at Ensham Mine in Central Queensland. All blasts comprised multiple layers that were blasted in a single drill and blast cycle, with unique designs applied to each layer to achieve different blast outcomes from the various layers.

Jan 1, 2006

By Ann Barron

Even though you think your company’s safety program is the best it can be, equipment, processes, supplies, surroundings and people do not always behave or react as expected. Consequently, needless accidents occur each year at quarries, construction sites, surface mines, and other locations where explosives are used. While blasting accidents account for only a small portion of the total accidents reported, the severity rate for blasting accidents is higher than for any other accident category.

Jan 1, 2007

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

By T. H. Chin, R. W. Bartlett

A simple on-stream particle-size analysis method is presented that leads to a bulk-property single-channel device; although the concept can be extended to multi-channel sizing information. The method is based on continuously measuring and comparing the percent solids in the sample stream and in an internal-reference stream containing only undersize particles. A semipermeable hydraulic system is used such that the particle mass concentration in the internal stream can vary, and is always proportional to the undersize particle mass concentration in the sample stream.

Jan 1, 1975

By Thomas J. Fisher, John J. Sammarco, Gary L. Mowrey, Edward F. Fries

This report (Safety File 3.0) is the fourth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2002

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By Carol E. Jones

?Reclaiming the land? in the Athabasca Oil Sands is becoming a household phrase in Canada. Advances in soil salvage and placement, increasing biodiversity of forest ecosystems and improved design of the landforms are beginning to change the trajectory of the ?reclaimed land? towards a boreal forest. The boreal forest is much more than just a forest; in the area of Fort McMurray AB, roughly one half of the boreal forest is composed of organic wetlands, often called muskeg. How important is muskeg to the boreal forest ecosystem and to the local aboriginal people? Should muskeg be reclaimed? Can muskeg be reclaimed? Ten years ago it was broadly accepted that organic wetlands could not be re-established; in fact this was so well accepted that reclamation of organic wetlands had not been attempted. Over the past decade this conclusion has been re-evaluated and research projects have been undertaken to examine the potential to create organic wetlands in a reclaimed oil sands landscape. This paper examines these questions and the research initiatives necessary to reclaim the other half of the Athabasca Oil Sands.

May 1, 2011

Volumetric measures [ ]

Jan 1, 1962

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

Corrosion is a chemical or electro-chemical attack on a metal by the surrounding medium, and it can be stated in general terms that a non-corrodible metal possesses that property either because there is no chemical action between it and the medium, or because the medium reacts quickly with the metal to produce a thin protective coating.When iron or steel is attacked by dilute mineral acids, for example, the products of the reaction are soluble and the formation of a protective film cannot take place; on the other hand, rusting produces a porous film which flakes away and offers little protection to the underlying metal. However, when chromium is alloyed with iron, its resistance to corrosion is improved because the films produced on such alloys become more adherent and tenacious as the proportion of chromium is increased. Chromium is thus an essestial constituent of the corrosion- and heat-resisting steels.During the 40 years which have elapsed since their initial development, these alloys have made an important place for themselves in in<lustry and commerce, and it is the object of this paper to 'describe typical examples of the many types which are available; also, to give some indication of their particular properties, and applications in the mining industry.NOMENCLATUREVery few of the alloys which are about to be described can strictly be considered stainless, and most are not steels in the sense that they can he hardened by quenching from...

Jan 1, 1951

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989