Search Documents

By Engelmann. William H.

In pursuit of innovative methods to improve mining productivity, the Bureau of Mines is investigating the use of inorganic salts as drilling fluid additives for penetration enhancement. Laboratory diamond drilling tests were performed on Westerly Granite with aluminum chloride solutions and on Sioux Quartzite with aluminum nitrate and aluminum, calcium, sodium, and zirconium chloride solutions as drilling fluid additives. These drilling results were compared with the average drilling performance using distilled, deionized water on Sioux Quartzite (12 replicate tests) and Westerly Granite (3 replicate tests). Maximum in-creases in penetration per given time and bit life were obtained when drilling with zero point of charge (ZPC) concentration solutions of each additive. For Sioux Quartzite, maximum increases in penetration and bit life ranged from 96 to 115 pct and 64 to 99 pct, respectively. For Westerly Granite, maximum increases in penetration of 155 and 165 pct and bit life of 109 and 136 pct were obtained at or near ZPC aluminum chloride concentrations of quartz (7.3 x 10-7 mol/L AIC13) and alkali feldspars (1.1 to 1.5 x 10-6 mol/L AIC13), respectively. This simultaneous increase in penetration per time together with extended bit life should result in increased productivity and reduced bit costs.

Jan 1, 1987

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Palmer C. Sweet

By-products from mining and processing plants and coal-fired power plants are being utilized more as valuable resources in Virginia. Mining-related by- products are divided into two categories: those generated from mineral extraction and beneficiation, and those generated from mineral processing or from industrial plants. Materials from both categories are produced in Virginia, where by-products have been exploited for various uses in the past and/or present. These materials include coal- combustion products (fly ash and bottom ash), lime-kiln dust, flue-gas-desulfurization residue, rock fines, magnetite, Cold Spring clay (kaolin), Austinville tailings, soapstone rock, and calcium-carbonate paste. Some of these by-products have never been utilized, although several ideas have been investigated over the years.

Jan 1, 1999

By P. K. Strangway, H. U. Ross

Briquets consisting of pure artificial magnetite, pure artificial hematite, and mixtures of the two were reduced by hydrogen in a loss-in-weight furnace at temperatures in the range 500° to 1000° . The rate of reduction of the pure hematite briquets increased continuously with increased temperature. In contrast, the pure nmgnetite briquets exhibited a pronounced rate ninimutn at about 700°C. Metallographic studies of partially reduced briquets rerlealed that, at this temperature, the he.matite samples reduced in a topo-chemical manner while the magnetite ones reduced uniformly throughout, and after partial reduction their cross sections contained a mixture of iron and unreacted wustite grains. No iron shells could be detected on the surfices of any of these uwstite grains. X-ray diffraction investigations indicated that these grains had a rzinimum lattice parameter when they had been formed at the rate rninimum temperature. Also, it was found that an activation energy of 41,000 cal per mole zoas required for reduction when only these wustite grains were present. Thus, it is suggested that the overall reduction rate of the rnagnetile su?nples at temperatures in the range influenced by the rate nzinirnum phenomenon was limited by the rate qf iron ion diffusion in the unreacted wustite grains. THE rate minimum phenomenon, which has often been observed when reducing iron oxides at a temperature of about 700°C, is one of the most interesting, yet unresolved, problems in the field of reduction kinetics. Basic principles of chemical kinetics and 'In some instance, a second rate minimum has been observed at about 900°C. Since most investigators are in agreement that this minimum is directly related to the transformation from a to y iron (which takes place at 911°C) and since it was not encountered during the present reduction tests, it will not be referred to in this vaver. fundamental laws of diffusion all agree that, as the temperature is increased, the rate of reduction should also increase. However, with certain ores, it has been found that their reduction rate actually decreases with an increase in temperature up to some value X where a minimum reduction rate is reached. With further temperature increases beyond X the rate becomes more rapid again. Temperature X is usually referred to as the "rate minimum temperature", while the overall type of behavior constitutes the "rate minimum phenomenon". This phenomenon has been reported by numerous investigators. They have found rate minima during the reduction of both artifiial' and natural374 magnetites and artificia15j6 and natural5" hematites. Rate minima have been observed when reducing high-purity material2 or low-grade ores,3'4 when studying particles in the micronsize range5 or relatively large agglomerates,g10 and during reduction with either hydrogen7 or carbon monoxide.11"2 Previously, this phenomenon has been attributed to many factors; these include sintering and recrystallization of the iron formed during reduction374 changes in microporosity of the ore upon redction,"" formation of dense iron shells around retained wustite grains,11716 and chem-isorption,17 to name only a few. However, most investigators who have reported a rate minimum merely speculated as to what seemed to influence it and they did not examine the fundamental causes. Consequently, the present experimental study was initiated in order to evaluate the basic factors which could be associated with this phenomenon. MATERIALS AND METHODS The experimental techniques, followed during this investigation, are similar to those which have been described previously.18 The chemically pure magnetic powder was prepared by partially reducing Fisher reagent-grade hematite with a gaseous mixture of carbon monoxide and carbon dioxide in a rotating-drum furnace. Three-quarter-inch diam cylindrical briquets which weighed about 12 g were formed from this magnetite powder and pure hematite powder. All of the briquets were sintered while they were slowly raised through the 1200°C hot zone of a vertical tube furnace. An argon stream was continually flushed through this furnace in order to prevent oxidation of the magnetite briquets, while in the case of the pure hematite briquets sintering was carried out in air. The sintered hematite briquets had a density of 5.06 g per cu cm while the density of the sintered magnetite briquets was 4.27 g per cu cm. The sintered briquets were reduced by purified hydrogen in a loss-in-weight furnace at temperatures in the range 500" to 1000°C. In all instances, the critical reducing gas velocity was exceeded and, in order to ensure that the results were reproducible, duplicate briquets of each type were reduced under each set of experimental conditions. A continuous record of the weight loss during reduction was obtained with the aid of a Statham transducer. The present experimental setup was capable of detecting a change in weight as small as 10 mg. Since a weight loss of over 2 g usually occurred during each reduction test, an accuracy of better than 0.5 pct of the total weight loss could be achieved. RESULTS AND DISCUSSION Reducibility Tests. In the first set of experiments, pure hematite and pure magnetite briquets were used.

Jan 1, 1969

By Ariti J

The mineralogy and extractive metallurgy of platinum and palladium in ores and residues is examined and the relative reactivity of Pt, Pd, PtS and PdS in cyanide and chloride media at 20¦C is discussed. Electrochemical measurements establish that Pd is readily leached in chloride media but more slowly in cyanide media due to a passivating PdO film. The passivating oxide film on Pt prevents leaching in either system at ambient temperatures. The results of leaching Au, Pd and Pt from an iron oxide residue obtained from the Sherritt Gordon Process using CN/air and Cl-/H202 are compared. It appears that passivation is overcome either by roasting at ?600¦ or by leaching at >_100¦C.

Jan 1, 1991

By R. H. Hanewald

INMETCO, a subsidiary of Inco Limited, is the only facility in North America that provides High Temperature Metals Recovery for nickel-, chromium-, and iron-bearing wastes. Since 1978, this process has prevented more than 775,000 tons of materials from becoming part of the nation's waste stream. The paper describes Inco's experience in metals recovery, traces the development and explains the operation of the High Temperature Metals Recovery Process, and examines the procedures and criteria used to determine whether spent catalysts meet process feed specifications. An overview of the current requirements for transporting spent catalysts is provided. The paper concludes with brief case histories of catalysts users employing High Temperature Recovery to manage spent catalyst.

Jan 1, 1995

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By Linping Yu

A simplified ED process was developed for organic acids recovery from cyclohexanone waste in this paper. In this regard, the one-stage ED was investigated directly without pretreatment, such as ion-exchange or nanofiltration to removal of foulants. The current efficiency and the energy consumption in the ED process for the recovery of carboxylic acids from cyclohexanone waste is theoretically analyzed and experimentally tested. The concentration of recovered carboxylic acid is related to many parameters and still needs more work to be determined.

Jan 1, 2009

By G. J. Krige

The extent of ground movements and stress concentrations in the vicinity of the reef in the deep mine-shafts used in the South 4frican gold-mining industry have led to the requirement that special tower structures be developed to span the reef intersection zone in several new shafts. So that structural engineers are able to design these towers, it is necessary to model the dynamic behavior of conveyances traversing them in some way, to provide a means to determine the magnitude of the forces generated. This paper describes the development of two such procedures. The first is a numerical method, utilizing a step by- step integration technique to track the motion of a conveyance through a tower. This technique has been implemented in a computer program, and some results are given.

Jan 1, 1995

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By Harold E. Marr

The computer program XRF4 was designed by the Bureau of Mines to provide for the calculation of several different interelement correction procedures in X-ray fluorescence analysis, including Lachance-Traill, Rasberry-Heinrich, and Claisse-Quintin procedures. The program was written in the BASIC language for timesharing application, and a conversational interaction with the computer is employed during operation. This report presents test problems using data for iron-nickel-chromium alloys and aluminum alloys and directions for use of the program.

Jan 1, 1976

By L. A. Wolff

"Second only to profitability (but not always), productivity is the most sought after measurement for any operation. Whether it is in mining, manufacturing, construction, etc. managers always strive to know how productive various plants are. Even the Federal Government publishes, on a monthly basis, the nation's factory productivity.Just what is productivity and how is it measured? This is an important topic that needs definition. There could be as many definitions as there are people who use it. In the mining industry, the problems of defining productivity would be analogous to the definition of equipment availability. Each mine uses its own definition to suit its needs. Webster's Dictionary primary definition for productivity is ""the quality or state of being productive,"" with productive defined as ""yielding or furnishing results"". This is a definition open to a broad spectrum of interpretation. A discussion of how productivity is currently used in the mining industry and an introduction to a potentially different approach to its measurement and meaning is outlined in this paper.Defining ProductivityTypically, mining companies track several productivity measurements. These are partial measurements and can include the following: tons per specific equipment class per hour, tons per man-hour, and tons per shift. None of these, however, track the over -all performance of an operation, that is, a unit of output per unit of input.For a mining operation, output can be defined as the ore for mill processing. Input includes the required components of production to get to the first step of processing.The Wesbter's Dictionary definition exposes a major fault with the popular conception of productivity. The critical issue of accountability is not addressed. Anyone can produce, but how effectively and efficiently are resources used? Quantifying an inclusive measurement is difficult. Statistics referring to an increase in productivity are often published. For example, the statement, ""gold productivity has increased by 10%"" has many potentially dangerous interpretations. One must ask, what does this statistic really mean? Did gold companies produce 10%” more gold? Were less manpower or equipment required to produce an equivalent amount of gold? Did ore grades increase resulting in more ounces of gold produced, etc. Obviously, production and productivity can have similar implied applications and meanings, but also two different, distinct meanings.To mitigate a problem like this, a standard needs to be developed within the mining industry. Because of varying ore grade, changing waste to ore ratios, different mining methods, etc. all of which have a direct impact on mining, development of a standard is difficult. Kendrick(1) discusses the use of Total Factor Productivity as a productivity measurement. Summarized, the total factor productivity measure is an indication of the change in efficiency in the use of basic labour and capital factors associated with an operation.This measurement has little meaning when calculated at a given point in time. It should be an on-going calculation, tracking an operation over a period of time, to evaluate trends. These trends can be used to determine if an operation's productivity is what it should be, and alert management to potential problems before they become major and adversely affect an operation."

Jan 1, 1990

By Guarascio M, Massacci P

In process simulation, more reliable prediction of industrial results and evaluation of data for design purposes and process optimisation may be attained by the combined use of: the modelling and simulation of ore characteristics, and 2. the modelling and simulation of the process. It is well known that geostatistical methods allow the defining of models of orebodies in which the variables considered are the grades of the valuable components. These models are proper for reserve estimation, geostatistical contouring, design and simulation of the exploitation method, and, in addition, for evaluating the variability of the ROM which is expected to be fed to the processing plant. However, no data are normally incorporated in the orebody model in order to evaluate the ore characteristics relevant for a reliable process simulation. The procedure for process simulation aimed at predicting plant results normally used so far consists in collecting samples from different orebody sites and building up a so-called 'representative sample'. On this sample, the ore characteristics (eg liberation, washability, grindability, etc) and the processing tests are referred to as the 'average behaviour in the orebody', assumed constant. A more reliable methodology consists in collecting samples from different orebody sites, in performing tests to characterise the samples from the point of view of the process (ore patterns), and in using synthetic parameters (process features). The values of the parameters are processed using geostatistical methods in order to develop a model for simulating the feed to the process. The estimation may thus be referred to the amount of recoverable minerals instead of to the existing minerals. Furthermore, the selection of the processes, the sizing of equipment and the design of control devices, as well as the prediction of results, become more accurate and reliable.

Jan 1, 1993

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2,3,4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6,7) and Majima and Takeda (El. These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976

By S. F. Emmons

Introductoy.—In view of the fact that an opportunity is to be offered to the members of the Institute present to inspect the recent developments of gold-deposits in the immediate vicinity of Washington it has seemed appropriate that some preliminary description of them should be given which may facilitate that inspection. It would have been a matter of much satisfaction to me to be able to present some general description of the gold-deposits of the Appalachian system ; but I have as yet had no opportunity of personally examining any others than those of Montgomery county, and these are still in their infancy. It is, moreover, a slower and more difficult operation to make geological observations in this region than in the more northern States; for whereas in the latter region the

Jan 1, 1890

By R. M. Schuller, J. J. Suloway, W. F. Childers, R. A. Griffin, S. J. Russell

Seven solid wastes from coal conversion processes were characterized chemically and mineralogically. The wastes included three Lurgi gasification ashes, two liquefaction residues (SRC and H-coal), a fly ash, and a water-quenched slag. Leachates generated from the solid wastes at various pH levels over the range 2.5 to 11.0 were analyzed for over 40 constituents. Results of the leachate analyses demonstrate the wide variation in constituent solubility for the solid wastes. To help assess the environmental impact of the disposal of these wastes, the leachates were also employed in soil attenuation studies and acute 96-hr static bioassays using young fathead minnows.

Jan 1, 1981

By Alexander B. Ikonnikov

All known bauxite deposits in China occur in its eastern half, and almost all of them are found in the Carboniferous and the Permian. They are of platform origin, but contain diaspore as the major ore mineral. There is only one known deposit composed of gibbsite. The most valuable deposits are sedimentary ones formed in local depressions on the edges of platforms during marine transgressions. They lie on Upper Cambrian or Middle Ordovician limestone that was weathered for a long period of geological time. Generally, Chinese bauxites are low in iron, and have a rather low alumina/silica ratio.

Jan 1, 1984

Christmas Island "C"-grade phosphate consists essentially of the minerals crandallite and millisite. Although containing over 25% P205, this material is not suitable for the manufacture of water-soluble phosphate fertilizers by conventional processes, because of its high iron and aluminium content Cover 25% total R203). In order to produce a water-soluble fertilizer from such material it is necessary to separate the iron and aluminium from the phosphate, which must report in a product acceptable as a fertilizer. Several processes were studied in detail. The first used ion exchange for dissolution and separation and yielded diammonium phosphate; processing costs were high compared with conven- tional processes based on apatite. The latter processes have basically simple flowsheets and cost of processing is low when compared with the costs of the raw materials. The need to separate iron and aluminium from the phosphate introduces additional complexity into the treatment of the C-grade material. The higher processing costs might be justified, however, if alumina could be produced as a byproduct. Two proposed processes have been developed in which: 1. hydrochloric acid is used for dissolution, and solvent extrac- tion for the separation of ferric chloride from phosphoric acid. Aluminium chloride is precipitated and hydrolysed to recover alumina and hydrochloric acid. 2. sulphuric acid is used for dissolution and aluminium is crystallized as ammonium alum. The phosphate is produced as an ammonium phosphate-sulphate fertilizer. High purity alumina can be obtained by treatment of the recrystallized alum. The technology of these processes is described, and their broad economics discussed briefly.\

Jan 1, 1971

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943