Search Documents

By R. Craig Smith

This report presents the software documentation for PREY AL, a prefeasibility mineral property evaluation program developed by the U.S. Bureau of Mines on a Lotus 1-2-3 spreadsheet. It is presented in a step-by-step "user?s manual" format. Appendixes contain the technical assumptions, program default values, and a summary printout detailing capital and operating costs and cash-flow analysis.

Jan 1, 1992

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS t ARE ASSOCIATES THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY THE FIGURES AT THE END OE THE ADDRESS INDICATE THE YEAR OE ELECTION HEAVY FACED T1 PE SIGNIFIES HONORARY MEMBERSHIP *ABADIE, EMILE R , Min Engr P 0 Box 83, Berkeley, Cal '76 *ABBE, CLEVELAND, JR, Geol Aid, U S Geological Survey, Washington, D C '00 *ABBOTT, AI ARTHUR, Cerro de Pasco Mining CO , Cerro de Pasco, Peru, So America '95 *ABBOTT, ARTHUR V , Electrical Engr , Westinghouse, Church, Kerr & Co , 8 Bridge St, New York, N Y '82 *ABBOTT, CLARENCE E, Chief Min Engr, Care Fayal Mine, Eveleth, Minn '04 *ABBOTT, JAMES W , Min Engr , Special Agent, Rocky Mountain and Pa¬cific Coast Division, U S Dept of Agriculture, "Tile New Markham," Denver, Colo '94

Jan 1, 1910

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By R. R. Wells

For several years the Klukwan deposit near Haines, Alaska, has attracted interest as a potential source of iron. Limited field and laboratory investigation has indicated that the deposit contains a large amount of Iron that is recoverable as high-grade concentrate. This report summarizes the results of laboratory beneficiation testing of the Klukwan ore, as represented by six samples submitted to the Alaska Experiment Station of the Bureau of Mines, Juneau, Alaska, Iron is present in the ore as a fine-grained magnetite associated with a pyroxenite type basic rock.. Satisfactory magnetic-separation procedures were developed for the production of concentrates assaying more than 60 percent Fe and 2 to 4 percent Ti02. During the investigation many data were obtained and compiled, but for convenience and clarity data of secondary importance have been omitted or condensed; only the more pertinent test results are discussed in detail.

Jan 1, 1953

By Joe B. Rosenbaum

New applications and concepts of solvent extraction as a unit operation in extractive metallurgy have been developed in the last decade. Wider use is being made of established solvent extraction techniques in processing spent nuclear fuel elements and in winning columbium-tantalum, hafnium-zirconium, thorium, tungsten, uranium, and vanadium. Commercial application has been extended to recovery of beryllium, boron, bromine, copper, molybdenum, phosphorus, rare-earth metals, and rhenium. Systems in use and proposed typically extract metals or salts as anion, cation, or neutral species from aqueous media by reaction with a recycleable organic reagent.

Jan 1, 1971

By I. Iwasaki, J. N. Orlich

The effect of slurry rheology and ball coating characteristics on the abrasive wear of grinding media and the rate of grinding were studied using -10 mesh quartzite in laboratory marked ball wear tests. Pulp viscosity was found to be closely related with both the thickness and physical characteristics of the coating affecting abrasive wear. The packing density of particles at the ball surface was the primary determinant of wear while the grinding rate was more dependent on viscosity and thus the ball coating thickness. The optimum grinding rate was achieved when the coating thickness was about twice the largest particle size.

Jan 1, 1988

By D. E. Munson, P. R. Dawson

An empirical model is developed that predicts accurately the transient response of salt creep to incremental and decremental changes in stress and temperature. Even though the model is empirical, it is derived from a firm theoretical framework for the micromechanical deformation processes of both steady-state and transient creep. In the model, the transient creep functions modify the steady-state creep behavior, which in turn is based upon creep mechanisms and the def ormation-mechanism map. The model is applied successfully to experimental stress-drop results obtained for salt.

Jan 1, 1982

By C. E. Jordan

Domestic cobalt resources are relatively large, but low grade. The full potential for cobalt production from domestic sources is at least 19.4 million lb of cobalt per year exclusive of offshore resources. A summary of the cobalt processing technologies for the major domestic resources is presented in this Bureau of Mines report. The processing technologies for the Blackbird, Madison Nine, Duluth Gabbro, iron ore pyrite, laterites, and manganese sea nodules are nearly complete, but the economics are not favorable. Research on these resources should be limited to approaches that promise to cut the total processing costs by at least 50 pct. The most promising sources of cobalt are the spent copper leach solutions and siegenite from the Missouri lead ores. Research on cobalt processing from these two sources needs to be completed.

Jan 1, 1988

By Raymond F. Mikesell

This paper evaluates the contributions of "third parties" to surplus capacity in the world metals industries in the 1980s. Special attention is given to the role of international development agencies, such as the World Bank, that have made project loans to state mining enterprises. The paper also reviews the contributions to surplus capacity of the International Monetary Fund and evaluates the large volume of credits from commercial banks to developing countries. Although the credits to Third World countries during the 1970s facilitated the expansion of mining capacity in those countries, no one source of financing can be held responsible for a significant portion of the expansion.

Jan 1, 1989

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By P. Peczak

A Monte Carlo simulation technique has been used to study dynamic recrystallization in polycrystals. A continuum microstructure of the polycrystal is modeled employing a discrete lattice. The response of the material to hot deformation is simulated by adding stored energy and recrystallization nuclei continuously with time. The experimentally observed nonuniform character of deformation substructures is modeled by employing a phenomenological expression for inhomogeneous distribution of the stored energy. All simulations were performed on HP-Apollo 9000 Series 700 workstations. A program written in FORTRAN with use of PHIGS graphics library calls was used to interactively monitor the current state of the matrix and all relevant parameters: deformation stress, average grain size and effective nucleation rate. Visual analysis of the simulated microstructure allows a better understanding of the data developed by averaging over a number of very long Monte Carlo runs. Since the essential features of dynamic recrystallization are accurately reproduced by the model, it is used to discuss the role of the controlling mechanisms of the dynamic recrystallization in real polycrystal.

Jan 1, 1993

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremo1ite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014

By F. C. von der Weid

The mining district of Sao Fidelis, in the northern part of the State of Rio de Janeiro, is situated on the Paraiba River, where it crosses the Serra do Mar (Mountain of the Sea), in the center of a mountainous country having numerous graphitic outcrops. For a long time, these outcrops were irregularly explored by local people, who had little means and no technical advice. A few years ago, the Cia. Brasileira de Mineracao de Grafite took over the control of some of the more important outcrops and entrusted to me the task of studying the ores and establishing a flowsheet for a pilot plant to be situated in Sao Fidelis—the ore to be concentrated being mostly of a very high grade. Mineralization and Ores The rocks of the district are mostly gneiss and crystalline schists, with occasional interstratification of dolomitic limestone belonging to the Archean Brazilian Fundamental Complex. The general direction of the beds is roughly between 60' and 80°E., with variable dip, generally nearly vertical. Mostly, direction and dip of the graphitic outcrops is concordant with the embanking gneisses or schists. These outcrops seem to be aligned in two or three parallel zones (Padua, Sao Fidelis, Mac- abu), the Sao Fidelis zone being the best known and the most important to date. Two outcrops of the Silo Fidelis zone, Saudade and Sao Benedito, are now being exploited. Mining has beer] carried out, so far, on a small scale. The mineralization consists of a vein of nearly massive graphite in a very compact, partially granitized gneiss, with vertical dip. The vein is most irregular, nith nests and lenses irregularly distributed along the fracture plane. The ore consists chiefly (particularly in Sao Benedito) of massive graphite appearing and disappearing along the main direction of the vein, forming a succession of irregular lenses in a sort of rosary design. The average width is more or less one foot, with variations from zero to 6 feet. The lode minerals are quartz, a little feldspar and garnet (the latter having its origin perhaps in the embedding gneisses), with rare ferruginous clays on the outcrops. In Saudade a little pyrite, pyrrhotite and chalcopyrite is found occasionally, as well as a carbonaceous mineral, very light, black and shiny, with conchoidal fracture, looking like a sort of jet. The composition of this mineral has not yet been established, but it seems to be very complex. The mineralization seems to be hydro-thermal at a rather low temperature, perhaps mesothermal. The paragenesis, according to samples from Saudade, seems to be as follows, the earlier minerals being listed first: pyrrhotite, pyrite, chalcopyrite, with quartz concomitant to the three and graphite formed later. Age of the mineralization is still uncertain, owing to the very in-

Jan 1, 1947

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By Kris De Bruyne

Since 2013, GSR has undertaken 4 exploration campaigns, which focused on environmental baseline monitoring (marine biology), resource definition and technological change. The seabed nodule collection vehicle has a significant influence on the achievable production rate and is for that reason thought to be a serious risk in developing an economical viable mining operation. GSR is currently working on a pre-prototype of a seabed nodule collection vehicle. The program, called ProCat, started in 2015 and will take up to end of 2019. ProCat can be split up in 2 phases: ‐ ProCat#1 [2015 – Q2 2017]: separate parallel testing of the nodule collection- and driving mechanism (Tracked Soil Testing Device Patania I – TSTD Patania I). The trafficability was tested in-situ; the collection mechanism was tested in a laboratory. Phase 1 has been completed successfully in September 2017. ‐ ProCat#2 [Q3 2017 – end of 2019]: the knowledge acquired during the first phase was used in this 2nd phase. Both collection mechanism and driving mechanism were integrated into the design of a pre-prototype seabed nodule collection vehicle (Pre-Prototype Vehicle Patania II – PPV Patania II). This pre-prototype vehicle will be used for a simulated mining test in Q2 of 2019 in the GSR- and BGR license area. The main objective of the ProCat research program, and especially the 2nd phase, is to integrate the nodule collector on the tracked chassis and develop an operating vehicle causing minimal environmental impact hereby validating the requirements for a full scale polymetallic nodule collection vehicle in the actual operational environment of the CCFZ. Following the ProCat project, GSR is working towards a system-integrated mining test once exploitation regulations have been agreed by the ISA and its member States.

Jan 1, 2018

By Michal Bukovansky

The Sahara Desert presents a serious obstacle to transportation route development in northwest Africa. Most highways and railroads are now limited to the coastal regions. A network of pioneer roads is the only connection between Algeria, Morocco, and Tunisia on the north, with Mali and Niger on the south. A feasibility study has recently been made for a paved highway between these countries. Climatic, geologic, physiographic and hydrologic conditions will significantly influence the construction of the road. In order to reduce costs, special construction methods will be required. An outline of these I conditions and methods is presented as an example of an engineering geological investigation in desert conditions.

Jan 1, 1970

What do you think are the major problems that the mining industry is facing? While I don't have any intensive knowledge of the various problems that plague our industry, I know that they are all part and parcel of a more complex and fundamental question: What must we do to make mineral extraction successful, safe, and profitable? Obviously, as mining people, we must continue to expand our technical know-how and to make better use of it. In today's context, however, that is not enough. We must also improve the "public image" of the mining industry. Why? Because the key word in the term "public image" is: the public. Many people in our country and in Congress, for instance, are against strip mining-and some are even against underground mining. Pressures from the public, from voters, have affected past, present, and new legislation. And government controls can be a major problem in any industry, let alone mining. At first, people ask government to intervene, act, or resolve problems, even in management and labor contract negotiations. But later, after Washington gets involved, there are clashes between departments and personalities, and eventually there is resentment against the interference with mining operations or our daily lives.

Jan 3, 1975