Search Documents

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By Wilson Blake

The Bureau of Mines used a mathematical model based on the finite element method of stress analysis to calculate stresses and displacements surrounding an open pit mine in a gravity-loaded rock mass. Comparison of the finite element solution for a semicircular notch in a gravity-loaded plate with the theoretical solution for a semicircular notch in a plate under uniform compression parallel to the free boundary demonstrates the inapplicability of the latter method to openings at the free surface of a gravity-loaded medium. High stress concentrations are formed at irregularities along the boundary of an open pit in a gravity-loaded continuous competent rock; however, for this type of rock the magnitudes of the stresses are too low to be considered a major factor in open pit slope stability. High stress magnitudes will occur if, in addition to the gravity stress field, a large horizontal stress field exists.

Jan 1, 1967

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

By George Hunt

THE first practical treatment of wood to prevent decay was devised early in the 19th century. At that time the oaken navy of England, when . the nation was fighting for its very existence, seemed doomed to annihilation by the swift ravages of decay. The acute situation inspired a desperate search for preventive measures and resulted in the development of the Burnett, Bethel and Kyan processes for impregnating wood with zinc chloride, coal-tar creosote and mercuric chloride, respectively. In the century that has elapsed, their use has spread throughout the world and the three original preservatives are used today in enormous quantities. Meanwhile, improved processes have been developed, new preservatives discovered, and the practice of impregnating wood to make it last longer has attained a position of major importance in the field of structural materials. USE OF PRESERVATIVES BY- THE RAILROADS In the application of wood preservatives in the United States the railroads have been the leaders for the past 50 years or more.. Having found, that decay is the chief cause of the early destruction of wood and that preservative treatment is the remedy, they have treated their ties and timber in increasing amounts(1) ?-in 1925 about 220,000,000 cubic feet. By preservative treatment the Santa Fe Railroad saves annually 1,500,000 ties in its 18,000 miles of track, and many other railroads effect similar savings. (2) In like manner the life of wooden bridges and trestles,(3) poles, marine piling, water tanks and other wooden railroad structures has been greatly increased, reducing the amount of timber required annually to maintain them.(5),(7)

Jan 2, 1927

By Robinson B, Ham B

Outbursts have occurred irregularly in the Collinsville Coal field since 1954 when an incident claimed seven lives. Further significant outbursts occurred in 1960, 1961, 1972 and more recently in the No. 2 mine in 1978. From the information collected over 25 years a comprehensive program to minimize the hazard of outbursts has evolved. Further developments of techniques to combat outbursts are being developed.

Jan 1, 1980

By J. A. Putnam, A. D. K. Laird

In laboratory research on the behavior of oil, gas and water in porous materials, no direct method has been devised to measure saturation without disturbing the flow. Indirect methods involving various forms of radiation have been developed for measuring one or two components. The X-ray absorption method for two components has been described previously1-3. The possibility of three component measurement has also been mentioned1. Since two component measurement still requires considerable care to insure accuracy, the fact that three components can be measured satisfactorily is not generally appreciated. The fraction of the energy of an X-ray beam of one wavelength transmitted through a material is given by the transmission factor. in which 1 is the beam's path length through the fluid. p is the fluid density, and 1,. is its mass absorption coefficient. Eq. 1 implies that all parts of the beam pass through equal amounts of the fluid. Practical applications are, therefore, limited to systems in which the fluid is distributed so that I varies negligibly over the cross-section of the beam. Typical variations of the transmission factor with X-ray tube potential arc shown in Fig. 2 from which experimental points have been omitted for clarity. The X-ray absorption of low pressure gases in a core is practically zero so it cannot he distinguished from that a vacuum by instruments that will differentiate between liquids. The transmission factor of a gas in a core is. therefore, unity. Consequently, the saturation of only one gaseous component can be found. If two fluids completely fill a core, their two saturations add to unity and, therefore, only one value of the transmission factor, T, is needed to determine both of them. When two liquids do not completely fill the core, their saturations do not add to unity and transmission factors at two wavelengths must be measured. At one of these wavelengths, 7 for one liquid must be different from T or the other liquid. The change of T for one liquid us the wavelength is changed between the two values must be different from the corresponding change of T in the other liquid. The two values of fluid saturation will also give that of the gas because the three saturations must add to unity. In Fig. 2 it can be seen that there are many large differences of T between various oil solutions and water solutions at any one potential, and between potentials for any one solution. Consequently, conditions for optimum accuracy of measurement of the saturations of a gas and two liquids can be chosen. Once the operating potentials have been selected, however. it is more convenient to cross plot the data from Fig. 2 on transmission factor-solution concentration coordinates for the chosen potentials, as shown in Fig. 3. Fig. 3 was used to plan the experimental procedure for Core N-38-1. Since the voltage control at 45 kv was good, the slopes of the curves in Fig. 2 at this potential would cause little error. At low potentials, however, the voltage control was not good, so 33 kv was chosen because the small slopes of the curves made voltage control less critical. The lowest strength beam that could be measured reasonably at 33 kv corresponded to a minimum T factor of 0.385. Fig. 3 shows that both 4.80 weight per cent of cadmium chloride in water and 24.0 per cent of iodobenzene in crystal oil had this T value, and, consequently, were indistinguishable to the X-rays at 33 kv. Thus, at 33 kv, the liquid saturation was given by the same curve regardless of the relative amounts of oil and water solutions present. This simple calibration curve from which the gas and liquid saturation can be read, is shown in Fig. 4. Fig. 3 also shows that at 45 kv, T for the aqueous solution is 0.610. and that T for the oil solution is 0.220. These values were transferred to Fig. 4 to give the triangular calibration plot from which the brine and oil saturations can be found, after the gas saturation has been determined at 33 kv.

By E. H. McCleary

The Alamo Mine The Alamo mine is located about seventeen miles northwest of Walsenburg, Colorado, on the Loma Branch of the Denver and Rio Grande Western railroad, in the foothills of the Black Mountains of Huerfano County. Prospecting Mr. W. B. Lewis of New York City, president of the Oakdale Coal Company and also president of the Alamo Coal Company first became interested in this property in 1920. After all natural features of the surface had been carefully examined by Mr. Lewis, he was convinced that the property was underlaid with coal seams. Plans for prospect drilling were made at once and this drilling was started late in 1921. In all, eight drill holes were put down to the Trinidad sandstone which underlies the coal measures in this field. These drill holes in general, showed very satisfactory results. Two workable coal seams were penetrated by most of these drill holes, the upper seam being six and one half feet thick and the lower seam having a thickness of ten and one-half feet. The two seams are separated by forty feet of sandstone and shale. Analyses of the seams proved each to be of a very high grade bituminous coal possessing hardness much above other bituminous coals, and having very bright lustrous appearance. Tests of more than a year's duration proved the coal to store excellently in closed bins and also in open bins where coal is exposed to elements. The drill hole data further showed the coal seams to pitch more than fifty per cent or about twenty-six and one-half degrees. The pitch direction being approximately South 65 degrees East. The drill holes further proved the coal seams did not outcrop at any point on the property, and no evidence of coal outcrop has been found in near vicinity. A splitting and pinching out of seams was found to occur some two hundred to three hundred feet of theoretical outcrop at very Western boundary of property. The most Easterly or No. 6 drill hole has a depth of eight hundred fifty feet to floor of lower coal seam. The Trinidad sandstone was found to be immediately under the lower coal seam, and the Pierre shales lying under this sandstone. Plans for Development and Sinking Having obtained sufficient data, plans for development of the property were carefully made sometime in advance of the actual opening of the mine. Every condition was carefully studied and the maximum production of clean and well prepared coal at as low a cost as possible during the entire life of mine was kept uppermost in the minds of all. The life of mine is estimated at approximately fifty years. It was decided to open up the lower and thicker seam first, and due to the pitch and other conditions a slope opening was decided upon for its extraction. The pitch of the coal having been found to be from fifty to sixty per cent or twenty-six to thirty degrees, the plan of driving the slope directly down the pitch of seam was eliminated and a plan that would give a more economical grade was decided upon. To obtain a lesser grade, a point several hundred feet west of-and at a less elevation than the theoretical outcrop of coal seam was selected for the slope opening. (Fig. 18.) To have driven directly down the pitch of coal seam would also have given the slope an uneven grade as the pitch of coal seam varied as it approached the crop. From this point of opening, the slope was to be driven on a thirty-one per cent, or' about seventeen degree pitch to intersect coal seam in No. 6 drill hole, a distance through the Pierre shales and Trinidad sandstone of two thousand five hundred fifty feet, the slope to be driven practically due East

Jan 1, 1925

By M. Timucin

High-temperature phase relations and thermodynamics of the condensed phase region of the Pb-S-O system at 1473 K were analysed by use of the available information. The sub-regular solution models on Pb-PbS and PbO-PbSO4 continuous melts were used in conjunction to generate a consistent set of thermodynamic and phase equilibrium conditions for the Pb-S-O system. The directions and distributions of conjugation lines between melts of this system were derived with relevant activity and composition data. The calculations permitted the thermodynamic analysis of direct lead smelting and the construction of isothermal reaction diagrams for the system in terms of oxygen and sulphur partial pressures at 1473 K.

Jan 1, 1989

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

Some of the problems of flotation, un- Solved in the mid-1950s, and possibly still unsolved today, are discussed with emphasis on dynamic aspects. These prob- lems include the nature of the air-water interface, particle-bubble contact and bubble attachment, and the effect of par- ticle size. Questions are also raised on the possible influences of the variability of minerals on flotation, particularly variations in composition and in foreign inclusions, both solid and fluid.

Jan 1, 1984

This paper discusses considerations to be made for the selection of rock tunnelling machines, as opposed to drilling and blasting. A systematic approach is presented in terms of utilizing data frcm site investigations to accurately forecast machine performance for estimating and planning purposes and to help minimise associated risks. Useful rock index properties are identified, and correlations for predicting advance rates for roadheader and full face machines are presented together with a simple method of characteristing rock mass conditions for estimating machine utilization and the savings to be gained in support costs. Finally considerations for tunnelling in adverse ground, for advance probing and for large sized tunnels are outlined.

Jan 1, 1987

By Gerald L. Tiley

When payloads and hoisting distances are beyond the capacity of a single headrope, a multi-rope hoist will cost less than, and require less maintenance than, several hoists with one headrope per conveyance. This paper describes the basic type of multi-rope drum and friction hoists in use today, the types of ropes available, and the essentials of a satisfactory installation.

Jan 1, 1981

Conventional logging tools such as density, neutron, and acoustic have ranges of investigation of tens of centimeters. The borehole gravimeter, however, has a range up to hundreds of meters. For example, from the center of a cylindrical orebody 0.22 g/cm3 denser than its surroundings, one can detect the boundary of the orebody at a radius as large as five times its height. More complex structures can be investigated with computer programs. We can predict the usefulness of proposed gravity surveys, or decide which suggested structure is most likely to have caused the results of existing surveys.

Jan 1, 1985

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015

By J. C. Franklin

The Bureau of Mines substantially reduced shale degradation in a coal mine by two spray coat applications of a water-base epoxy sealant. More than 12,700 square feet of passageways were treated, and in 18 months only one failure occurred. This failure was due to improper spray application, Material costs averaged 13 cents per square foot, and labor costs were 7 cents per square foot. Labor included moving all materials into the mine, the setup time for each of the areas coated, and application of coatings.

Jan 1, 1977

By T. A. Wheat

"The presently increasing world-wide interest in advanced ceramic materials is generally focussed on their exploitation in both structural and functional applications. With the opportunity to engineer microstructures and thereby closely control and tailor the final properties, there are many new applications being made for these materials in both areas.The scope and some of the applications for functional ceramics are reviewed and examples of the present Canadian activity in this field are discussed.BackgroundThere has been progressively increasing international interest in the development and exploitation of ceramic materials in the last five years. The stimulus for this interest arises from several quarters, each of which are independent of the other.• There is a growing awareness of the strategic nature and vulnerability of supply of the raw materials used to produce high performance metal alloys.• The metal alloys are reaching the upper temperature limit for their performance as structural components in engines.• The dramatic increase in oil prices during the late 1970s focussed attention on the need for reduced consumption in many sectors, i.e., there is a need for more efficient engines that operate at higher temperatures - above those tolerated by the present superalloys.• A number of ceramics, especially the structural materials such as SiC, A120 3, AI20rSi02, Si3N4 and the Sialons are produced using non-strategic raw materials and they can exhibit startling performance-auto turbo-rotors are in production mad e of Si3N4 that operate up to 190000 rpm at 600°C, 150000 rpm at 900°C.• Ceramic s are generally of lower density - significant in the weight-reduction of automobiles such as the replacement of a 20-kg five-segment steel leaf spring with a single segment carbon-fibre reinforced unit of 3 kg. • Ceramics also offer major ad vantages in generating, monitoring or controlling the electromagnetic spectrum whether in bulk or thin-film devices that exploit optical, magnetic, pyroelectric, piezoelectric, electronic and I or ionic conductivity characteristics.The opportunity to combine several of these char acteristics in a single material by composition, processing and microstructural design has resulted in an advanced ceramics industry that had world-wide sales in 1980of $4.2 billion (U.S.)(I) and is predicted to grow to sales in the range $7 to $10 billion by 1990 and $16 to $24 billion by the year 2000(2). However, at present, advanced ceramics account for less than 20010 of the total ceramic market."

Jan 1, 1987

By Tobias W. Goodman, Joseph Cervik

This Bureau of Mines report investigates the horizontal trajectory of boreholes drilled in coalbeds using the rotary drilling technique. Test holes drilled in coalbeds showed that the path of a borehole in the horizontal plane depends on drilling assembly configuration, drill bit rotation, and coalbed geologic features. An assembly that contained an 18-ft (5.53) long drill collar and two centralizers had the best horizontal stability evidenced by trajectories that deviated less than 16 ft (4.9 m) from a target at 1,000 ft (305 m). Removal of one of the centralizers resulted in a loss of control of hole trajectory in the horizontal plane. Generally, holes tended to turn to the right, presumably because of right-hand rotation of the bit. Deviations from the original bearing line were as much as 200 ft (61 m) or more at a depth of 1,000 ft (305 m).

Jan 1, 1988

By Anders Nordqvist

LKAB operates an underground iron ore mine in Malmberget in the northern part of Sweden. Twelve different orebodies are mined today using both longitudinal and transversal sublevel caving as mining method. The town of Malmberget is located close to the mining area. The need for urban transformation, moving people and houses, is evident for many reasons. The mining methods used have inherent subsidence issues and there are also vibrations from blasting and mine induced seismic events.

Jan 1, 2018