Search Documents

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

Dr. Robert Bell died on June 18, 1917, at Rathwell, Manitoba, in the seventy-seventh year of his age. He was born in Toronto on June 3, 1841, and was a son of the Reverend Andrew Bell of the Free Church of Scotland. He was educated at the Grammar School of the County of Prescott, Ontario, and subsequently at McGill University and the University of Edinburgh. While still a boy of 15 years of age, he joined the Geological Survey of Canada, under Sir William Logan, in the capacity of Junior Assistant, and was rapidly promoted in the service, where lie remained-with but one short interval-for over fifty years, retiring as Chief Geologist and Acting Director in the year 1908. He married Agnes, daughter of the late Alexander Smith, of Westbourne, Glasgow, and Auchentroig, Stirlingshire, and is survived by one son and three daughters. Practically nothing was known of the geology of Canada, and very little with reference to its geography, when Mr. William E. (afterward Sir William) Logan was called upon to undertake the organization of the Geological Survey of Canada, and as its first Director to carry out the mapping of this vast area and the examination of its mineral resources. Dr. Bell's work as a member of Sir William Logan's staff in these early years consisted, therefore, exclusively of geological reconnaisance and geographical exploration. Even in later years, and until his administrative work confined him to his office, Dr. Bell's work remained essentially of this character. The exploratory traverses and track surveys which lie carried out were, chiefly within the area of the great Laurentian protaxis or Canadian Shield, which forms such a striking feature and which has played and will continue to play so important a role in shaping Canadian history and in influencing the character of the Canadian people. Dr. Bell's lines of exploration crossed and re-crossed this area from the Atlantic Coast to the Great Lakes on its western border, and from Lake Huron and Lake Superior on the south to the Arctic Sea, following the water ways of this great land. He also worked along the coast line when acting as geologist and naturalist to the "Neptune" Expedition in 1884, and to the "Alert" Expedition in 1885, both of which carried out explorations in Hudson's Bay and Hudson's Straits; also on the "Diana" Expedition in 1897, when he surveyed the coast of Baffin Land, and was one of the first white men who penetrated to the great 'lakes in the interior of that immense

Jan 11, 1917

Accidents in open pit mining have a high cost in lost time of person- nel, damage to equipment and installations, and lost production. The realities of export competition require that Mine Management sig- nificantly reduce the costs associated with accidents and workplace ill-health. Newer management approaches are proving effective in reducing the Total Cost of Risk through a strucured Occupational Health and Safety Programme exhibiting the following features: ò Formal Company Policy ò Accountability for OH&S performance clearly designated to each level of management and supervision ò Effective utilisation of a Mine Occupational Health and Safety Co- Ordinator and a Mine Occupational Health and Safety Adviser ò Development of realistic OH&S Objectives ò Training of Management, Supervision and Workforce in Occupa- tional Health and Safety ò Development and adoption of Safe Work Practices and Procedures ò Effective employee selection procedures, control of Contractors ò Monitoring of the health of the workforce ò Collection, recording and distributing information on all Mine inci- dents, accidents, injuries and damage ò Ensuring that the Mine environment is healthy and safe ò Effective Emergency Procedures to deal with injury, fire, rescue and other situations of risk ò Controlling those Mine hazards which cannot be removed ò Adopting a high standard of Occupational Rehabilitation ò On-going visible Management participation in the programme to ensure that momentum is developed and maintained. This approach requires that Occupational Health and Safety be given equal status with product quality, maintenance of plant and output per- formance; its implementation is rewarded with improved morale and major cost reductions.

Jan 1, 1989

By Gerard C. Gambs

The electric utility industry is the largest customer of the U.S. coal industry, consuming nearly 50% of present coal production. By 1980, the electric utilities are expected to burn over 500 million tpy of coal or 75% of total coal production. When coal is burned in electric utility plants, ash is produced in one of several forms. These include fly ash, bottom ash and bottom slag. At the present time, approximately 20 million tons of these ashes are produced and must be disposed of by the utilities at a cost of 50[c] to $2 per ton. In 15 years, more than double this quantity will be produced. Only a small quantity of this ash is put to any practical use. Much remains to be done about expanding uses for fly ash and bottom slag.

Jan 1, 1967

By L. Voisin, K. Itagaki

In the reductive smelting of the copper concentrate like a blast furnace operation using coke as fuel and reductant or in processing the copper concentrate which contains coal in the bulk, a sulfur-deficient matte phase often coexists with an iron base alloy in the bottom of the smelting furnace. This alloy is generally called furnace residue or speiss when considerable amount of arsenic or antimony is contained in the alloy and in the extreme case of reducing condition the alloy is saturated with carbon. As a fundamental study to know the behavior of some precious metals such as silver, gold and platinum between the sulfur-deficient matte and the furnace residue or the speiss which are in equilibrium under reducing condition, the phase relations and distribution of precious elements in the Cu-Fe-S-As and Cu-Fe-S-Sb systems saturated with carbon were determined at 1473 K by a quenching method.

Jan 1, 2007

By Richard D. Hagni

Abstract-Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in mill Products. The mill dressing engineer should be more aware of the types of beneficiation problems that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations of the mineral constituents of an ore or mil1 product can be visually determined. This advantage provides solutions to many beneficiation problems. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in floculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 10, 1978

Although the flotation cell has been under continuous development over the past 80 years, an understanding of the precise roles of a cell in produc- ing the flotation result had evolved slowly. In fact, detailed studies of cell dynamics began only in the 1940s when flotation practice had almost reached the half-century mark. The earliest generalizations related cell capacity to power intensity (hp/vol- ume) (Rose, 1946), and specific operating features such as aeration and power ' consumption to impeller submergence and operating speed (Read, 1933). In the 1950s hydrodynamic characterization of cells through power coefficients and air flow numbers began (Arbiter and Harris, 1961) and has continued to the present, with increasing industrial use of these concepts (Degner, 1982; Degner and Treweek, 1976). Liquid flow measurements in Wemco cells (Degner, 1982) made liquid flow numbers and turnover frequencies available for more complete under- standing of cell dynamics. The present overview of flotation technology is a critique of cell design. The cell process represents the interactions between cell dynam- ics, cell geometry, and ores, with the latter prepared for that interaction through size reduction and reagent treatment. While previous invest- igations of flotation cells have accepted all cell designs uncrit- ically, the present study considers the physical process components that an effective cell must provide, and then compares a limited number of

Jan 1, 1984

By Alexander V. Epiforov, Stanislav V. Balikov

This paper describes of processing tests of 8 flotation concentrates containing precious and base metals by pressure oxidation (POX) method. Concentrates 1 and 2 were gold-copper concentrates. Zinc and silver were by-products in these concentrates. These concentrates were processed by POX with following cyanidation of POX solid residues, copper solvent extraction and zinc carbonate precipitation. The recoveries of gold, copper, silver and zinc from these concentrate were 98, 99, 30 and 99%, respectively. Concentrates 3 and 4 were lead-zinc concentrates. Silver was by-product in concentrate 3. Gold, silver and copper were by-products in concentrate 4. Concentrate 3 was processed by POX with following reduction smelting of POX cakes for primary lead recovery and zinc carbonate precipitation from POX solution. The recoveries of lead and silver into ingot were 96 and 98%, respectively. The recovery of zinc was 99%. Concentrate 4 was processed by POX with following zinc carbonate precipitation and reduction smelting of POX cakes. Copper was precipitated from the POX solution using sodium sulphide prior zinc precipitation. The recovery of zinc into carbonate concentrate was 99%. The recoveries of lead, gold and silver into lead bullion were 95, 99 and 98% respectively. The recovery of copper into sulphide concentrate was 99%. Concentrate 5 was gold-pyrite concentrate, and concentrates 6-8 were double refractory gold-arsenopyrite concentrates. Silver was by-product in these concentrates. These concentrates processed by POX and CIL. The recovery of gold from concentrate 5 was 98%, and from concentrates 6-8 was 85-90. Low gold recovery from concentrates 6-8 was associated with preg-robbing factor. The recovery of silver from gold-sulphide concentrates did not exceed 10-20%. The low silver recovery was associated with argentojarosite formation that is resistant to cyanidation. The flowsheets for complex processing of precious and base metals sulphide flotation concentrates based on this test work results were proposed.

Jan 1, 2018

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Mining is a very water intensive industry. As such, the industry has become dependent on applying alternate sources in efforts to minimize the impact on the locally available fresh water. Sources such as recycled water, sea water, and even acid mine drainage have been applied at some limited applications, while other mines may not even have the option of fresh water available in their region. However, the different sources of water will have varying concentrations and types of soluble salts and suspended solids, which can lead to dramatic differences in mineral processing when comparing these types of waters. Water quality is known to affect bubble generation and strength, mineral surface charge, and even reagent coordination properties. This paper focuses on the exploration of how water quality and soluble salts affect the flotation of iron and titanium containing minerals from feldspar, and the design of flotation collectors for optimal performance in this water.INTRODUCTIONFeldspar is defined as a tectosilicate mineral with the generic structure of MAlxSixO8, where M represents the cation (Celik, 2001). Feldspar is most often found naturally occurring with quartz, iron containing minerals (i.e mica), and titanium containing minerals (i.e. rutile). The alumina component of feldspar is of interest to glass making, while the alkali metal component is of interest to ceramics (Vidyadhar, 2002). In glass making, the alumina is known to improve product hardness, durability, and resistance to chemical corrosion. In ceramics, the alkalis act as a flux; a flux lowers the melting temperature of the mineral mixture, and assists in connecting the other components present in ceramics. Quartz is stated as having a negative effect on the melting point of the feldspar. Although quartz is typically not removed during the feldspar applications in the glass industry, it needs to be reduced for the ceramics industry. Iron and titanium based minerals are known to have negative effects on color and quality of the products in both glass and ceramics. Thus, these “contaminants” must be reduced to a certain product specification via feldspar beneficiation (Table 1)."

Jan 1, 2016

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By Vladyslav P. Yakubovsky, Boris I. Bondarenko, Valentin A. Noskov, Vladyslav M. Sokolov

"Each of Ukrainian producers of ferronickel, stainless steel and synthetic diamonds has the same basic problem with recycling their fine Ni-containing secondary materials. The conditions for generation of them along with the correspondent properties were investigated in details. The new approaches for their recycling have been proposed. They are based on application of some pyrometallurgical processes that are used in Ukraine. The proper equipment is also available. It has been shown that the dust from laterite calcining process of ferronickel production should be efficiently recycled by sintering. The stainless steel dust should be smelted after briquetting as a charge addition to the Ni-containing discarded batteries in the elaborated furnace. The sludge after synthetic diamonds production should be pelletized and processed by liquid cast iron with application of induction magnetodynamic forces in the specific furnace.IntroductionThe object of the investigation is recycling the Ni-containing secondary fines in a form of dust and sludge. There are several generators of the fines in Ukraine. Namely they are Pobuzhye Integrated Ferronickel Mill; Electrometallurgical Works “Dneprospetsstal” with stainless steel plant as well as Poltava Diamond Plant that produces synthetic hard materials. Their businesses are the largest in the Commonwealth of Independent States (CIS). However the status of handling with the fines is not perfect since the applied recycling technologies are low efficient. The landfilling option is often adopted for them. At the same in Ukraine there are some nontraditional pyrometallurgical recycling technologies and equipment that should be tried for application in smelting these secondary materials.Recycling the sludge of synthetic diamonds productionThe sludge of “Poltava diamond plant” from production of synthetic hard materials has a following chemical composition, %: iron oxide – 29.7; chromium oxide – 18.97; nickel – 4.27; manganese oxide – 15.2; sulphate – 3.85; natrium – 14.9. The content of moisture is 70-80%. The moisture quite quickly evaporates while keeping sludge out of doors. Sludge returns into the weak agglomerates. The sizing of the dried sludge particles presents the figures from 400 to 1000 µm. The moisture was extracted by sludge pressing. The content of the basic compounds of the moisture is, g/dm3: chromium oxide – 1.6; nickel – 0.001; manganese oxide – 0.002; lead – 0.005; sulphate – 13.6; natrium – 17.0."

Jan 1, 2008

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By Edgar E. Vidal

The deposition of ceramic materials onto substrates is of special interest in the development of surface related technologies. Research interest has been placed on using thermal plasma as the deposition method, specifically inductively coupled plasmas. Many different modifications to the same basic principle of deposition have been performed through out the materials research community. Such a technique may have many advantages over more conventional techniques, such as high deposition rates, high surface area coverage, clean energy source, no contamination from electrodes and operation near atmospheric pressures. Materials deposited vary from simple oxide systems like TiO2 to more complex structures like ternary oxides and nitrides. This paper reviews recent developments relative to the inductively coupled plasma deposition of thin films.

Jan 1, 2003

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

Several short color films describing new technology developed through Bureau of Mines research are available on a loan basis. The films review results of Bureau research programs aimed at aiding the minerals industry by increasing mine productivity, ensuring worker health and safety, and enhancing minerals recovery, processing and recycling. Most of the films are available in a choice of for mats: 16mm film, ½" VHS cassette tape, or ¾" U-matic tape. The films are loaned by the Bureau of Mines free of charge; borrowers are requested to pay only the return postage and for any damage to the films. All titles are also available for purchase in 16mm or videotape formats. Interested persons wishing to borrow or purchase a film should specify its title and the preferred and alternate showing dates. All requests should be addressed to: Motion Picture Library Bureau of Mines Cochrans Mill Road P.O. Box 18070 Pittsburgh, PA 15236 A short description of each film follows: Safer Coal Mining Equipment Traces the development of modified conventional and continuous mining equipment, beginning with an investigation of the problems encountered with mining equipment and continuing through long-term testing of the modified equipment in two mines. "Human engineered" coal mining machines are shown in operation. These machines include features such as adjustable cabs, easy access controls, improved illumination, and other safety improvements. (19 min)

Jan 1, 1986

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By Slavko Ostojic, V. G. Hill

This paper reviews various bauxite classification schemes with respect to the differences in texture, composition and geological associations of the deposits. It demonstrates that a techno-economic classification, based on: a) associated rock type - lateritic versus karstic, b) content of aluminum ore minerals - gibbsite, boehmite and diaspore, and c) gangue minerals (iron oxides etc.) has a geological basis with natural cut-off points for the bauxite types identified. Thus, this scheme is seen as applicable to bauxite resources. It also provides a basis for their rational exploitation taking into consideration the long-term interests of both the bauxite producing and consuming countries. Against this background, the industrial mineral or non-metallurgical grades of bauxite are seen as localised and relatively rare occurrences. Their consumption should, therefore, be aimed toward the specific (hence more remunerative) products as indicated by the bauxite characteristics.

Jan 1, 1984

By John W. Trammell, Chester O. Ensign

Efficient mining of copper ore at the White Pine mine in Michigan's Upper Peninsula is partially dependent on the rather unique problem of predicting variations and rock types in a barren stratum called the upper sandstone. The pronounced effect which this formation has on the local mining techniques is reflected by the necessity of deciding whether to mine the sandstone along with ore-bearing rock, thus diluting overall ore grade, or, alternatively, leaving the sandstone behind to form the mine roof. THE OREBODY AND MINING TYPES In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions (Fig. I). Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 1. Other authors have dealt in detail with the stratigraphy and mineralogy of the orebody, so it will suffice here to call attention to the low copper content of the upper sandstone.

Jan 12, 1964

By L. Yuan, J. H. Rowland, R. A. Thomas

"Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners. INTRODUCTION As many types of battery-powered mining equipment such as scoops and shield haulers are used in underground mining operations, charging stations are required to charge the equipment batteries. These batteries are of lead acid chemistry. A safety issue exists with the battery charging stations as all lead acid batteries produce flammable H2 gas during the normal charging process. Overcharging or excessive heat can quickly cause batteries to produce even more H2. If H2 is not appropriately diluted or dispersed, it builds up, and the risk of fire and explosion increases. Mine Safety and Health Administration (MSHA) regulation (30 CFR Part 75.340) requires that battery charging stations should be housed in noncombustible structures or be equipped with a fire suppression system. When a fire suppression system is used, the battery charging stations must be ventilated with intake air that is directed into a return air course or ventilated with intake air that is monitored for CO or smoke using an AMS. The monitoring of intake air ventilating battery charging stations should be done with sensors that are not affected by H2."

Jan 1, 2018

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006