Search Documents

By Merle L. Bowser

The Bureau of Mines has constructed a miniature oxygen deficiency alarm system using an electrochemical cell as the sensor. Distinct audible signals are produced at either of two preselectable oxygen levels which can be varied from approximately 10 to 20.9 percent oxygen. The high or cautionary range produces a 500-cycle-per-second tone pulsed at about a 1-cycle-per-second rate, whereas the lower or more dangerous oxygen level produces a continuous 500-cycle-per-second tone.

Jan 1, 1968

By H. W. Norman

DURING the first few years of the new atomic age the Colorado Plateau was the focal point of uranium exploration. There was little incentive to expend time and effort in an area so far removed from the known deposits as the Pacific Northwest, and there were too few local prospectors to cover the vast territory involved. In 1949 the AEC established an exploration office in Spokane to evaluate the uranium potential of the northwestern states. Interesting occurrences were found in the Coeur d'Alene district in Idaho and in the Boulder Batholith of central Montana, but the AEC discontinued the Spokane office in 1952, and for the next two years prospecting in the area was negligible. In April 1954 John and James LeBret, prospecting on the Spokane Indian Reservation with an ultra violet lamp, located an occurrence of the fluorescent uranium mineral autunite. This discovery was not announced until the following September, after a lease had been granted by the Spokane tribe. Exploratory drilling carried on by the AEC throughout the winter verified the existence of a commercial orebody. This property, the Midnite mine, has since developed the largest known ore reserve in the district.

Jan 6, 1957

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By M. E. Shank, J. Wulff

In view of the current interest in magnetic materials having rectangular hysteresis loops, as for example those obtained with the grain oriented 50 nickel 50 iron alloys,t we wish to call attention again to the results obtainable with the perminvar (Co-Ni-Fe) alloys heat treated in a magnetic field. Data taken from direct current measurements made prior to and during World War II give the typical values shown below for two of the perrninvar alloys. Fig 1 and 2 show- the hysteresis loops for these samples. The first sample above consisted of small rings punched from 0.014 in. sheet stock. These rings were heat treated at 1000°C for one hour in a hydrogen atmosphere and then cooled with the furnace to 750°C at which point they were subjected to a magnetic field of 15 oersteds maintained during cooling to room telmperature. The molybdenum perminvar sample consisted of a spirally wound core of 0.001 in. tape. The heat treatment was the same except that box annealing methods were used and no hydrogen atmosphere was employed. Even better properties might be expected using hydrogen. The heat treating temperatures and cooling rates are not critical. Rectangular hysteresis loops produced in other perminvar alloys by heat treatment in a magnetic field were described earlier.',? Properties similar to those described above are realized in perminvars manufactured by conventional methods. Drastic cold working which in practice limits the final thickness and is gen- erally expensive may thus be avoided. This information may be of interest to those concerned with magnetic alloys and the development of contact rectifiers, magnetic amplifiers and so on.

Jan 1, 1950

By D. Duvris

Health and safety issues are a very important aspect of mining activities. Although the application of scientific research and current technology shields workers from many dangerous aspects of mining, accidents do happen. Many companies and institutions worldwide have committed to a continuous effort to minimize such occurrences. In this study, the health and safety data pertaining to the Greek mining and quarrying industry for the last 3 decades are presented and critically evaluated with respect to number of workers, annual production, etc. Appropriate indices are also calculated regarding the incidence and frequency of accidents. Health and safety issues specific to mining in Greek are also discussed.

Jan 1, 2000

As it is the plan of the War Department to return 400,000 soldiers a month during the next four months, Colonel Arthur Woods, Special Assistant Secretary f War, has requested the Engineering Societies to assist the Government by soliciting their members to advise the respective societies, at the earliest possible moment, f any place where companies can employ returned soldiers. This request applies not only to the professional men who are returning but also to the miners, mechanics and other skilled labor among the enlisted men. Army discipline has not only made these men think more quickly but also more willing and obedient workers. The whole training has been conducive to regular habits and clean living steadying these men and fitting them to meet emergencies more quickly and has instilled more loyalty to their superiors and to their jobs. Further, the military instruction they have received has increased the men's powers f concentration. The War Department cannot too strongly bring before the employers of skilled labor the fact that the employment f discharged soldiers will be advantageous to the employer and economically beneficial to the country. The following is a list of the vocations of the men who are now returning:

Jan 6, 1919

By E. G. Noble

Microbial leaching is being investigated as a method for recovering the metal values from a domestic low-grade manganese wad ore. Early work showed that heterotrophic microorganisms present in the ore solubilized manganese when cultured in a glucose-mineral salts medium. More recent shake-flask tests using molasses as the sole nutrient source extracted 97 pct of the manganese from minus 300- µm ore in 4 weeks. Column bioleaching with the molasses medium solubilized 99 pct of the manganese from minus 6.3-mm ore in 50 weeks. The results of flask, column, and lab-scale heap bioleaching studies are presented.

Jan 1, 1991

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By B. R. Maas

Processing material at a consistent rate through the continuous countercurrent decantation (CCD) thickeners presented a major bottle neck to unlocking additional value from one of the post-flotation streams at the Kansanshi processing plant. The manual operation of the thickeners making up the CCD train resulted in frequent imbalances and process upsets across units. The automation of CCD trains is notoriously tricky as the available manipulated variables are outnumbered by the parameters requiring regulation. The implementation of an advanced, auction-based, control philosophy to manage the movement of both slurry and solution inventory through the train addressed this parameter imbalance and lead to the stabilisation of the circuit. Since the commissioning of this control strategy: an additional 7 200 dmt/day (+36% throughput) of material can reliably be processed through the train, the number of monthly downtime events has reduced, and a saving of $354 000/month in reagent cost has been achieved. INTRODUCTION CCD operation Agitated leaching is a common method used in hydrometallurgy to extract a metal from its host ore. The host ore is initially finely ground to liberate the surfaces of the valued minerals and improve the kinetics of the leaching process. The ore is then contacted in an agitated tank with a lixiviant to dissolve the desired metal into the aqueous phase. The resultant slurry from the leaching process comprises of a solution pregnant in the metal salt and a barren ore. The first purification step taken after leaching is to wash the pregnant liquor solution (PLS) from the depleted ore. On the industrial scale, a set of between two to ten thickeners arranged in a countercurrent configuration is often used to carry out this separation (Perry & Chilton, 1973). The slurry is introduced at the head of the train and a wash solution at the tail. The two streams are pumped through each thickener countercurrent to one other. At each stage the residual PLS in the slurry is mixed and diluted down with the countercurrent overflow solution from the downstream thickener. The diluted slurry is fed into the thickener where the solids separate out through gravity sedimentation. The settled solids are channelled towards the underflow of the thickener by a rake mechanism and pumped downstream to the next thickener in the train. The outcome is the recovery of a PLS from the overflow of the lead thickener and a slurry of washed solids from the underflow of the tails thickener.

Jan 1, 2019

By I Coombes, M Trim, Y Sun, M McRae, A Spiegl, H Lagger, A Amon, P Barraclough, M Villeneuve

The Brisbane Airport Link Project (AirportlinkM7) includes the design and construction of more than 12.5 km of tunnels, with the Kedron interchange including four ramp tunnels that intersect with mainline tunnels and result in caverns with spans of up to 26 m. These caverns are in highly variable ground conditions with less than 35 m of cover underlying residential neighbourhoods and commercial properties. The Kedron caverns were constructed using the sequential excavation method (SEM). Owing to complex geometry and excavation sequence, the caverns were designed based on numerical modelling methods, including both two- and three-dimensional models. These numerical methods were used to develop a suite of support types with excavation sequences for the expected range of ground conditions. A combination of methods that included in-tunnel monitoring (convergence monitoring and extensometers), probe holes, endoscope probes, face mapping and ground settlement measurements were used to verify performance of the tunnel support systems and to select and refine the appropriate support system for each section of the caverns. The construction monitoring data indicated that numerical modelling can provide a good basis for predicting the performance of large-span underground openings in highly variable ground conditions. This paper presents a comparison of the performance of the caverns predicted by state-of-the-art numerical models and the actual measured performance.CITATION:McRae, M, Villeneuve, M, Trim, M, Sun, Y, Barraclough, P, Spiegl, A, Amon, A, Lagger, H and Coombes, I, 2014. Brisbane Airport Link Project – design and construction of the 26 m span Kedron Caverns: comparing monitoring data with the design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J. C. Jaeger

It frequently happens in engineering and mining situations that "bad" rock is encountered which consists of rock broken up into blocks a few inches or less in diameter by a network of intersecting joints. These joints may be open, or filled by veins of solid material, or covered with weathering products. Essentially, the material consists of an aggregate of small interlocking blocks. In such circumstances, major joint systems usually can be recognised and studied, but there are probably many minor planes of weakness which may cause the blocks to be of almost random shape. It is extremely difficult to determine the properties of such materials. Measurements on small specimens give the properties of the constituent rock and not the jointed material. At the other extreme, the material has occasionally been tested as loose aggregate in large triaxial pots, but this gives no information about the strengthening effect of the interlocking of the small blocks of rock. One simple approach, which has been much used, is to regard the rock as randomly jointed on a small scale and to apply soil mechanics theory to it. In this case, the normal and shear stress at failure are related by [ ] where the coefficient of friction p and the cohesion c will be those of the individual joints. Even in very bad rock, it is usually possible to drill core in small diameters of 1 to 2 in. which will contain a number of joints, both open and filled. The testing of such joints provides one simple method of determining some of the properties of closely jointed rock and will be discussed in detail in the next section. Calculations based on Eg. 1 with values of c and µ obtained in this way may be expected to give a lower limit for the strength of structures in rock.

Jan 1, 1970

By Nicolás Luis, Qi Liu, Gonzalo Montes-Atenas

"The prediction of froth flotation performance is still an unresolved topic. Classic industrial models based on particle size, elemental and mineralogical information provides recovery results with deviations that may become significant. One possible reason for this deviation may be the fact that the current liberation analysis provided by electron microscope based techniques does not take into account the outmost surface layer composition of liberated particles. In order to complete the description provided by the liberation analysis, other spectroscopy techniques measuring the extreme surface of the minerals can be tested. For instance, X-ray Photoelectron Spectroscopy (XPS) is a technique which measures the first tens of nanometers providing elemental composition over the particle surface and allows resolving the elemental associations present at the surface sample. However, this information needs to be statistically robust, reproducible and most importantly representative of what is occurring in the process. The aim of this research work is to develop a statistical model based on particle population to evaluate the feasibility of turning the XPS technique into a metallurgical tool. The model consists of classic statistical population arranged in a bed of heterogeneous particles with a known grade and mineral liberation. The simulations showed that the XPS results statistically followed a well-defined pattern. The statistical results were confronted with pilot plant results obtained from a rougher bank when processing a copper sulfide ore from a Chilean mine site. It was observed that the probability function distribution was in agreement with the experimental data. Further analysis on how the XPS results provide valuable information improve the computation of froth flotation recoveries is also discussed."

Jan 1, 2014

For. the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE, ST. LOUIS, M.O. FIRST VICE-PRESIDENT C. W. GOODALE, BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N.Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 8, 1918

By C. E. Nelson

THE purpose of this discussion is to outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as far as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, the principal aim of this paper will be to deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux.* The flux provides protection during melting and a molten pool of flux into which the solid magnesium melts. It is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies; then on quiet standing separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is usually desirable. The open-pot method is used generally in the following processes: (I) alloying and secondary smelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings requiring hand ladling, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protec-

Jan 1, 1944

By Douglas Baker

Zinc concentrates assaying approximately 54% zinc and 30% sulfur are roasted in a suspension type roaster to yield a zinc oxide calcine assaying about 65% zinc and 0.40% sulfur. This calcine is the feed material to the sulfuric acid leaching section of an Electrolytic Zinc Plant. The SO2 gases resulting from the elimination of sulfur from the concentrates are passed through a waste heat boiler for the generation of high pressure steam, cleaned by a baghouse, and delivered to the humidifying tower of a sulfuric acid plant system. The gases are then treated in a mist precipitator for final fume removal and then converted to sulfur trioxide in a three pass contact system using vanadium pentoxide catalyst for the manufacture of sulfuric acid. Waste heat steam is used to power the steam turbine which drives the acid plant blower.

Jan 1, 1970

By R. Karl Zipf, Z. T. Bieniawski

"Abstract. Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation.In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions.An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further understanding of the mechanics of fine fragment formation in coal."

Mar 1, 1989

By Michael S. Wieland

Toxic fume concentrations from industrial mining explosives depend somewhat upon the type of rock (or other strata) confinement. Though traditional detonation theory disregards this influence, the work principal from thermodynamics reveals it, when the violent interactions that transpire within the rock blast are taken into proper account. Resolution of the work principle technique requires total thermodynamic equilibrium under constraint, so the nonequilibrium dynamics is rendered in that way, using an old trick from theoretical mechanics that revises the representation of forces. The rock pressure reduces to a four-component sum: the rock compressive strength and natural atmospheric pressure, as reckoned quasi-statically, and the gravitational influence and reversed inertial resistance, as reckoned dynamically. Tabulated specie concentrations and graphical trends reveal the dependency upon rock pressure, rock temperature and the fuel-oil percentage in ammonium nitrate mixtures (ANFO), used to illustrate the model. Rigid-wall test chambers have notable ullage (residual space), where rapid expansion influences the reaction quenching, yielding a fume spectrum unlike that for rock confinement; reported rock tests are therefore used for comparisons. For the thermodynamic regime where quenching occurs, seven concentrations are resolved, including carbon monoxide (CO) and total nitrogen oxides (NOX). Their trends yield inferences regarding the way unwanted charge desensitization from transitory hole-to-hole wave impact in conjunction with reduced rock pressure can yield nasty toxic fumes, the dark rusty cloud phenomenon!

Jan 1, 2005