Search Documents

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By J. L. Bray

IT is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-alumi-num system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1. Others2,3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to

Jan 1, 1936

By Jon Y. Kaneshiro, John S. Griffith, Anthony F. Stirbys, Mauricio Andrade

This paper presents an overview of the New Mississippi Tunnel Outfall for the Transportation Expansion Project (T-REX). The Outfall conveys highway and other urban drainage to the South Platte River as well as provides long needed relief from flooding problems in the southeastern portion of the Interstate 25 highway corridor. The Outfall tunnel incorporates a one-pass precast concrete segmented liner to convey storm water under I-25 then under Mississippi Avenue to the river. The Outfall crosses both the existing I-25 as well as the future improvements including under the Light Rail Transit, a new bridge abutment, widened lanes, and new retaining walls. The Outfall also crosses adjacent to several buildings and five bridges, under major traffic and utility intersections, and through difficult geology.

Jan 1, 2003

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948

By A. H. Hassan

Stibiotantalite is a relatively rare mineral not commonly found in the major tin districts of the world, and its separation characteristics have not been documented adequately in the literature.

Aug 1, 1979

By K. G. Chipman

THE discussion on Dr. Chipman's paper, Mapping by the Topographical Survey, centred mainly on the urgent need for aerial photographic reconnaissance of unmapped portions of the country as an initial phase in the provision of suitable topographical maps for use as a guide in geological mapping, prospecting, exploration, and development work in the areas concerned. This, ir was pointed out, would necessitate an expansion of the topographical work of the Bureau of Topography to keep pace with the photographid work and to meet the demand for maps for use by geologists of the Bureau of Geology and others. A resolution requesting Institute Council to make representations to the proper authorities, urging that aerial photography and topographic map-ping be greatly expanded to meet the pressing needs of the situation, was moved by DR. W. F. JAMES and seconded by MR. L. G. SMITH, and carried unanimously. The full text of the resolution appeared on page 221 of the May BULLETIN. Others who spoke in support of the resolution were MESSRS. E. S. MOORE, L. B. ROCHESTER, F. D. SHEPHERD, and W. J. WRIGHT. Dr. Hansen then presented his paper, Mapping by the Geological Survey, discussion on which is summarized below. MR. FRANK EBBUTT(l) spoke of the very valuable service the Geological Survey bas rendered the mineral industry, and indeed the whole nation, in its century of existence, despite the very inadequate financial support it has received. Now, more than ever before, a strong and expanded Geological Survey is essential if the Industry is to continue to prosper. Our known ore reserves are being depleted very rapidly, and we are finding no new orebodies to take their place. As an aid in prospecting and exploration, and also in the development of orebodies when they have been found, we must have geological maps of the vast sections of the country which at present are unmapped or inadequately mapped. The Institute should make every endeavour to have the Geological Survey strengthened so that such maps may be made available as soon as possible.

Jan 1, 1944

By Sadough vanini Ali

Charpy impact energy of functionally graded steels produced by electroslag remelting in crack divider configuration has been modeled in various strain rates. It has been well known that majority of materials indicate different behaviors under different strain rates and temperatures. Therefore, modifying the elastic-plastic model considering the effects of strain rates and temperature gives us an acceptable prediction of these composites behaviors in impact test. In this investigation, graded steel was divided in to several layers in which the layers have the same strains under the impact. Constitutive equation describing the flow stress variations as a function of strain rates and temperatures, have been used to express the stressstrain behavior of layers. The parameter values of constitutive equation determined for all the layers via using the boundary conditions based on composite graded behaviors which were the characterized ferrite, austenite, bainite and martensitte phases. Consequently by applying the rule of phase mixtures and ascribing the impact energy of each layer to the area of stress-strain curve of the same layer, the whole impact energy of composite is the sum of layers impact energy with considering the layers volume fraction.

Oct 1, 2011

By Francis W. Brown, Philip R. Hunt, Douglas N. Halbe

Refractory arsenopyrite ore from Western Mining Corporation's Lancefield deposit in Western Australia is treated by fluosolids roasting of a flotation concentrate followed by cyanidation of calcine and flotation tailings. The project development is reviewed from original testwork through circuit design, operating experience, and subsequent expansion.

Jan 1, 1990

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By G. W. Rhodes, B. P. Cavan, F. K. Mussger

The New Austrian Tunneling Method (NATM) has been successfully applied to two very different tunneling projects in the U.S.. In the case of Pittsburgh's Mt. Lebanon Tunnels, two original design alternatives were prepared. The NATM alternative incorporating a reinforced shotcrete final lining was successfully bid and constructed. At Washington Metro's (WMATA) Section B-10 Glenmont Route, Wheaton Station and tunnels, a NATM value engineering redesign was prepared for the low bidder. The design incorporating a waterproofing system based on a PVC membrane between the initial and final linings was accepted by WMATA. In both cases, European experience and standards were meshed with U.S. standard practice. Examples of NATM flexibility as an original design and as a value engineering proposal are presented.

Jan 1, 1985

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Mariah Mikesell

"Two types of metallic deposits have been found in the deep Arctic Ocean: Hydrothermal Fe, Cu, and Zn sulfide deposits form along Gakkel Ridge in the Eurasia Basin and associated ridges between Greenland and Europe; and iron and manganese oxide crusts (Fe-Mn crusts) and nodules, precipitated from seawater onto rock surfaces in the Amerasia Basin, contain many rare metals of economic interest. Fe-Mn crusts and nodules collected in the Amerasia Basin during 2008, 2009, and 2012 cruises on the USCGC icebreaker Healy are characterized by unique mineral and chemical compositions, very high Fe/Mn ratios, fast growth rates, and other unique characteristics compared to those formed elsewhere in the global ocean. These characteristics reflect temporal and spatial variations in geological, oceanographic, and climatic conditions in the Arctic Ocean and surrounding continents over the past ~15 Myr.RESULTS AND CONCLUSIONSDiscrimination diagrams show that the crusts and nodules found in the Amerasia Basin north of Alaska are hydrogenetic. However, the mineralogy is not typical for hydrogenetic Fe-Mn crusts and nodules, which usually include only amorphous Fe oxyhydroxide and ?-MnO2 (vernadite). The Arctic samples also include the Mn oxides birnessite and 10Å manganates (todorokite, buserite, asbolane), and the Fe minerals also include goethite, lepidocrocite, feroxyhyte, and ferrihydrite. This mineralogy reflects formation under lower oxygen conditions than typical for samples formed elsewhere.The Amerasia Basin crusts have a unique chemical composition compared with crusts from other areas of the global ocean. The key difference is the high Fe contents relative to Mn contents, which determines the types of trace metals hosted by the Fe-Mn oxide phases, and their concentrations. The high Fe/Mn ratios reflect the expansive continental shelves (>50% of the Arctic Ocean) and upper slopes that support redox cycling and release of Fe and other metals to bottom waters, and to the large fluvial input from North America and Siberia. Brine formation on the shelves and currents promote the distribution of the metals throughout the Amerasia Basin, including the deep basins."

Jan 1, 2017

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By Clifford O. Hamilton

In both mature and young maintenance workforces, the workforce commonly lacks some of the skills required for their assigned work. We call this the "skills gap." This skills gap usually exists in a new operation because although you may hire qualified maintenance personnel, they more often than not have little if any experience with the specific equipment at the facility. Performance Associates International, Inc., has developed and proven a technique to address the maintenance skills gap that is usually found in a new operation.

Jan 1, 2001

By P. Stanley Jacobsen, Hemant B. Gala, Richard E. Hucko

Coal is the nation's most abundant fossil energy resource. However, its use is limited because of the nature and amount of associated impurities, such as mineral matter, sulfur, trace elements, and moisture. The moderate-to high- sulfur content of many U.S. coals is of particular concern as current and newer, potentially more stringent, regulations require reduction in sulfur oxide emissions. Release of particulates, NOx, and other pollutants during the coal-use cycle is also of concern. The current practice of controlling sulfur oxide emissions in the major steps of the coal- use cycle is limited mainly to coal preparation by physical beneficiation and, to a smaller extent, to post-utilization cleanup (flue gas desulfurization). Approximately two-thirds of the coal from states east of the Mississippi river is physically cleaned, whereas only 15% to 20% of the operating boilers in the utility industry are equipped with scrubbers to desulfurize the flue gas (Henzel, 1988). Physical beneficiation methods can be very effective in removing mineral matter, including pyritic sulfur, from coal. These processes take advantage of the differences in physical proper- ties between coal and mineral matter to achieve the separation. In a typical physical cleaning operation, raw coal is crushed to about a 50-mm (2-inch) top size. It is then screened into coarse, intermediate, and fine sizes. Crushing the coal liberates some of the ash-forming minerals, including a portion of the sulfur that is not chemically bound to the coal. The per- centage of impurities freed from the coal matrix generally increases as the coal particle size decreases. The coarse- and intermediate-sized coals are typically subjected to a cleaning pro- cess based on differences in specific gravity between coal particles and the associated impurities. Such cleaning processes used include jigs, dense-medium baths, cyclone systems, and concentrating tables. The fine-sized (typically less than 0.5-mm) coal, if beneficiated, is typically cleaned using a froth flotation technique based on the differences in surface proper- ties between coal and its associated impurities. At fine sizes, greater cleaning potential exists because a greater portion of the impurities is released from the coal matrix. However, this potential is not fully realized owing to inefficiencies in separating fine particles using state- of-the-art flotation technology. Overall, current commercial coal preparation processes are estimated to remove up to 60% of the ash and 10% to 30% of the sulfur, depending on the coal characteristics, with product weight recoveries rang- ing from about 60% to 90% and thermal recoveries of about 85% to 98% (Versar, 1985; Science Applications International Corporation, 1987; Hoffman- Muntner Corporation, 1978). For many U.S. coals, grinding to sizes finer than those used in current coal preparation plants is required to liberate most of the physically bound impurities from the coal matrix. As noted, conventional coal-cleaning methods are not very effective at these fine sizes. Accordingly, the expanded use of domestic coal requires the development of advanced coal cleaning technologies that can provide economic performance while reducing environmental impacts. Program Goals and Objectives The overall goal of the U.S. Department of Energy (D0E)'s Coal Preparation Program is to provide the scientific and engineering knowledge base that industry can utilize to produce economically competitive and environmentally acceptable clean-coal products for introduction as market conditions warrant. The coal preparation process(es) should remove undesirable components from coal and improve its handling characteristics, thus making the product coal technically, as well as economically, viable as a competitor with petroleum-derived fuels and natural gas, and with alternative environmental control technologies. The coal preparation process must be applicable to a wide variety of bituminous and low-rank coals. The cleaning process should reduce the variability among clean-coal products from various raw coals, thus significantly increasing the range of potential end uses for each raw coal. To the extent that deeply cleaned coal products have greatly reduced levels of

Jan 1, 1988