Search Documents

By A. W. Laughlin

Analytical costs are a major part of exploration programs in developing nations which may lack adequate laboratories. Laser-Induced Breakdown Spectroscopy (LIBS), a variant of atomic emission spectroscopy, can reduce exploration analytical costs and can provide the analytical results in <1 minute. CPI is now marketing battery-powered, backpack mounted analyzers, using LIBS to analyze for many elements of interest to the explorationist. LIBS is well suited to the analysis of elements in industrial minerals. Limits of detection in ppm for some of these are: Li-1, Be-2, Na-100, B-33, Sr-10, Ba-300, Cs-1, K-500, Fe-500, Mg-500, and Ti-500.

Jan 1, 1999

By R. D. Hagni

The following is a case study illustrating the use of thin sections and polished sections of crude ore to predict metallurgical response. By examining polished sections of the metallurgical products, the textural and mineralogical reasons for unsatisfactory separation can be explained. An area of oxidized Negaunee Iron-Formation located south of Negaunee, Michigan, in the Marquette Iron Range, has been considered for roast reduction-magnetic separation. Preliminary metallurgical studies and subsequent pilot plant testing produced varied results. These results prompted this microscopic study which began with an examination of 126 thin sections and 82 polished sections prepared from 126

Jan 1, 1967

By W. C. Burnett

The land phosphate deposits of the U.S. southeastern coastal plain have long been a major factor in the world trade of phosphate rock (Fig. 1). As recently as 1979, deposits of North Carolina and Florida alone accounted for about 33 percent of the entire world&apos;s phosphate exports. This situation is changing, however. World production increased by ~9 %, yet the U.S. share was down to ~28% in 1984. A complex interaction of economic and political factors combined with increasing costs of raw materials, production, and transportation have led to this systematic erosion of the U.S. market share. Changing land-use patterns within the southeast, environmental pressures, exhaustion of shallow high-grade resources in Central Florida, and the increased pressure from expanding low-cost production in other countries throughout the world account for much of the present difficulty in the U.S. phosphate industry. Considering this depressed environment -- what are the prospects for development of offshore resources? A summary of new research on offshore phosphorite within the U.S. Exclusive Economic. Zone (EEZ), as well as an attempt to place possible development of these resources within the current economic setting, is the purpose of this presentation. We will emphasize work in progress on a major offshore deposit along the U.S. Atlantic Margin as well as new research on Pacific Ocean occurrences of phosphorite on seamounts and insular slopes within U.S. waters.

Jan 1, 1986

Effects of DA as a Grinding Aid on Selective Grinding of Low-Grade Bauxite Effects of DA (a copolymer of acrylic acid and acrylamide) as a grinding aid on selective grinding of low-grade bauxite were investigated in this study. The addition of DA into the grinding system enhanced the selectivity of grinding and increased the A/S ratio in the coarse fraction of ground product, leading to improved throughput of grinding mills and alumina recovery. The results showed that DA decreased the viscosity of slurry significantly and hence improved grinding efficiency due to low viscosity at a high slurry concentration. Both the hydrogen bond formation and chemical adsorption existed between DA and the surface of bauxite particles. The adsorption of DA on the surface of bauxite could decrease stress needed for crack initiation and extending during grinding, prevent new-born crack surfaces from rejoining, and promote the expansion of the cracks.

Sep 13, 2010

By George H. Ashley

Mining, including quarrying, dates back almost to the dawn of history, beginning almost with the beginning of what we call civilization. State surveys date back about 100 years. Evidently mining flourished for thousands of years before state surveys were thought of. Why should it not continue to flourish without state surveys? First, it may be noted that as mining and civilization were contemporaneous, so state surveys and the science of geology were almost contemporaneous. As recently as 30 years ago the United States mineral laws were interpreted to mean that coal lands in the public domain were only those lands on which workable coal outcropped. The half billion acres of public land underlain by .coal but on which it did not outcrop were treated as homestead lands and open to settlement. Just what did the science of geology do to or for the mining industry? Until geology arose rocks or minerals or ores were where they were found. Their finding might be accidental, or might be the result of deliberate search or prospecting. In open, rocky country, with little or no vegetation, as in parts of the West, prospecting served very well, though at an enormous expenditure of human time and effort, if not money. The old saying that every dollar&apos;s worth of gold taken from the earth has cost two dollars may largely be charged to the time value of the usual method of prospecting. Geology changed all that. The science is still young and it still labors under handicaps of immaturity and early errors. Geology, however, has gradually been discovering the relations and conditions under which the several mineral deposits occur. Its elaborate studies of exhausted or nearly exhausted mineral deposits has done for it what human autopsy has done for medicine and surgery. Perhaps in no field is this plainer than in the oil and gas industry. Note might also be made of several important coal fields in England and on the Continent, in which the coal is everywhere deeply buried. Passing over the long period of growth during the past 100 years, geology today is prepared to offer the mining industry: first, a knowledge of the geologic conditions under which most minerals occur and to explore

Jan 1, 1935

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket&apos;s process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker&apos;s procedure. This modification differs from Tucker&apos;s method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By Bowra N

Working capital is best described as money that must be supplied from a company&apos;s treasury to buy inventories for raw materials and finished products and to provide credit to customers who have not yet paid for delivered products. Working Capital requirements for resource projects are to a large extent, dependent on specific characteristics of the projects concerned. Important variables are the nature of the project and speed with which sales can be realised. The project&apos;s location is also important as this will influence inventory levels. Working capital requirements have a time profile, the present value of which can represent a significant portion of a projects overall capital needs. A significant component of a project&apos;s working capital is not readily recoverable or able to be reassigned should the project fail or be deferred.

Jan 1, 1986

By Oliver B. Hopkins

"WE HAVE patterned our lives on the things we take from under the earth's surface. Our civilization is built upon the ore from which we obtain our metals and the fuels which power the world as we know it.Today I should like to discuss with you a newcomer to the ancient mining industry. This lusty infant of which I speak is just a century old - the oil industry.While one doesn't commonly think of oil men as delvers in the earth, It was by sinking a shaft that the first oil was obtained commercially in Canada. Men sank a shaft in a ‘gum bed' in southwestern Ontario's Lambton county, not far from Petroilia, and distilled from the gum a burning oil That was just a hundred years ago. The gum was originally liquid petroleum which had seeped to the surface and lost most of its volatile components.Later, the miners dug down to •bed-rock and soon after they were not digging but were drilling wells, as they have been ever since. From the wells they obtained erode oil.What is crude oil? It is not an element like gold, silver or lead, •but a complex mixture of compounds. These compounds are made basically from two elements, carbon and hydrogen, and are called hydrocarbons (Figure 1).The remarkable ability of these. Two elements to combine in different ways gives crude oil its physical and chemical character. The lighter hydrocarbon compounds in it are gases, at normal temperature and pressure, and these are dissolved in the other, heavier compounds."

Jan 1, 1952

By J. V. Batty

Various ores from deposits in the Boulder Dam Recreational Area, Clark County, Nev., were submitted for ore-dressing tests as part of the Bureau of Mines studies of western manganese ores. The Virgin River manganese deposit is situated on the Virgin River arm of Lake Mead, 5 miles from Bonelli&apos;s Point, which was formerly the junction of the Virgin and Colorado Rivers. It is 20 miles from Overton, Nev., and 26 miles from Boulder City, Nev. The ore body, composed of wadlike manganese in a tuffaceous gangue, is a flat-lying bed overlain with beds of gypsum and basalt. Two ore samples were submitted by engineers of the Bureau for ore-dressing investigation. Low-grade sample 1 was a composite of channel samples cut from outcrops of the ore body; sample 2, of intermediate manganese grade, was taken from the dump-at the exploratory shaft sunk by the Bureau. The Boulder City manganese deposit is situated in the Boulder Dam Recreational Area -3 miles southwest of Boulder City. The ore body is a manganiferous gypsum bed 32 feet thick, slightly inclined from the horizontal. The ore sample submitted-by engineers of the Bureau for-testing was taken from channel cuts in the walls of the shaft, which cuts through the bed vertically.

Jan 1, 1948

By I. V. Kubrakova, O. A. Tyutyunnik, M. L. Getsina, A. M. Asavin

An analysis of noble metals (NM) in natural samples is most problematic. Determination of their traces in geochemical samples, in part, for the purpose of deposit evaluation, is a difficult analytical task. A number of international standard reference materials of rocks and ores, in which NM content is certified, is estimated at a half dozen. For example, in the International proficiency test for analytical geochemistry laboratories (GeoPT), which is held by the Department of Earth Sciences (The Open University, United Kingdom), the data for gold and platinum are observed very rarely, and the results obtained in different laboratories differ on 1-3 orders of magnitude. It is caused by low contents of NM in nature, by a variety of their complex and mineral species, as well as by a complicated matrix composition of platinum-containing objects. Among these objects are ferromanganese ores, enriched strongly with Fe, Mn, Ni, REEs - the elements hampering a precise determination of NM due to a complexity of instrumental inter-element correction. The absence of the reliable methods of NM determination in these ores drastically limits the possibility of deposit evaluation.

By W. Kauenhowen

The production of petroleum in Germany during 1932 totaled about 1,608,558 bbl., a slight increase over the 1, 602,517 bbl. produced in 1931. A decline, as shown in Table 1, occurred chiefly in the Volkenroda (Thuringia) field. The total production of the other fields (salt domes), however. reached a new record, about 21 per cent above 1931. Table 1.—Oil Production of Germany by Fields and Oil Provinces, 1928-1932 (Barrels of 42 Gallons)" Salt Dome Province __________________________________________________|_________________________________________________________________________________________________________________________ 1928 274,323 322,742 679 46,319 644,021 644,315 1929 310,891 337,582 10,535 67,578 719,901 720,069 1930 586,404 427,539 100,716 72,485 1,186,969 29,806 1,220,296 1931 506,548 403,634 213,549 116,088 1,242,598 360,885 1,602,517 1932 769,405 366,982 230 979 130,711 1,498,077 110,481 1,608,558 " Official figures published in Germany are given in metric tons. For the above conversion into barrels a factor of 1 metric ton equaling 7 barrels has been used. Includes a very small production from Hcide, Holstein. c Includes a very small production from Tegernsee, Bavaria, and Bruchsal, Baden. Nienhagen-Hanigsen Field In 1932 the Nienhagen-Hanigsen yielded about 51 per cent of the production from the four German salt dome fields. During 1932 the productive area was again extended, chiefly towards the northwest in the so-called north district, to which the present drilling activity is confined almost entirely. Since the discovery of the north district in 1928, about 45 wells have been drilled in it, of which only two were

Jan 1, 1933

Mills Day left a journal of his travel to Ohio and return by way of Pittsburgh in 1810. He left this comment about western Pennsylvania: "June 19. As I proceeded toward Pittsburg, (From Washington and Canonsburg) the country grew more populous. The hills appeared to consist of strata of freestone, iron, coal, and slate. June 20. Its (Pittsburg&apos;s) water communication with a vast extent of country and the immense beds of coal in its immediate vicinity render it a place peculiarly adapted to manufactures. Coal may be obtained of a good quality, ready delivered at 5 cents a bushel."1 Until within a year or so of this period, coal was used for domestic purposes, brick-making, by blacksmiths, etc.; now the industry entered a period of rapid growth caused by the introduction of the steam engine. As manufacturing was increasing due to the settlement of the western country, the additional facilities created by mechanical power were welcome. Apparently the first engine was installed in Pittsburgh, in a steam grist mill, in 1808; it is described in the Navigator of 1811: "The water of the boilers are heated by large fires made of stone coal, which is introduced at one end into a grated fire place as long as the cylinders themselves; the quantity of coal consumed daily by these boilers is said to be about twenty bushels, which cost one dollar." Later it mentions the effect of burning coal:

Jan 1, 1942

By J. Sibakin, R. D. Hindson

In order to devise a practicable soaking pit schedule for use at The Steel Co. of Canada Ltd.&apos;s Hamilton Works, soaking pit heating temperatures, sooking times, pit capacity, and safe maximum mill drafts were correlated with fluctuations in the current or load of the bloom mill driving motor. Other variables such as total delays in the pit, rolling schedules, mill delays, and track times were also investigated. IN order to show an easily applied and accurate means of establishing soaking pit heating temperatures, soaking times, pit capacity, and safe maximum mill drafts, these various factors are correlated herein with fluctuations in the current or load of the bloom mill driving motor. Rolling practices have a considerable influence on the production capacity of a blooming mill. The maximum values of the torque, in particular, are of importance, since even instantaneous current peaks lead to the tripping of the motor by the overload relay and result in loss of mill time. The establishment of safe maximum drafts and accelerations for ingots of different sizes and of a soaking pit practice which would ensure a consistent and satisfactory plasticity of the metal is of considerable importance for increasing the efficiency of both the blooming mill and the soaking pits. The Bloom Mill Dept. of the Hamilton Works, The Steel Co. of Canada Ltd., is equipped with one 44 in. mill driven by a 7000 hp motor with the setting of the overload relay at 22.0 ka. The speed of rotation of the motor is regulated after the Ward-Leonard system. There are three basic speeds of 9.5, 28, and 47 rpm and a further possibility of increasing the speed by weakening the field. This last possibility is hardly ever used during practical operations. The rolling program of the blooming mill is varied, both in the size of the ingots to be handled and in the steel grades. The total tonnage handled by the mill is about 2,000,000 ingot tons per year. At the time of the investigation, the Bloom Mill Dept. was equipped with 22 soaking pits (6 regenerative, 14 bottom-fired, and 2 one-way top-fired pits) with a total bottom area of 2770 sq ft. The pits are fired with a blast furnace-coke oven gas mixture having a calorific value of 155 Btu per cu ft. The foregoing figures show that the production program was such as to impose the necessity of a most efficient usage of the available equipment. For this purpose, the operations of the 44 in. mill and of the soaking pits were investigated, and the results of the investigation were used as a basis for a revised soaking pit schedule and drafting practice. The plasticity of an ingot of a certain chemical composition when being rolled is determined mainly by the following factors: I—the ingot size, both thickness and width; 2—the length of the gas soak; and 3—the surface temperature. The first two factors determine the uniformity of the temperature distribution over the cross-section of an ingot. The third factor introduces the level of the heating of an ingot. The torque produced by an ingot being rolled is determined by the area of the metal displaced, its plasticity, and acceleration values. On the other hand, with shunt motors the torque is determined by the current. This can be assumed to be correct with only a small degree of error for compound motors with a relatively small effect of the series windings as long as the velocity is not regulated by weakening the field. Since the spread is relatively unimportant when compared to the width of an ingot and since it is also reduced several times during rolling by edging passes, the draft alone and not the area of the metal displaced may be taken into consideration with ingots of a similar size. It is therefore possible to determine the main features of the heating and drafting of an ingot by measuring the current and acceleration of the mill motor. After the acceleration has been taken into account, the amount of current will be an indication of how the motor responds to a heating and/or drafting practice and these practices can be adjusted in order to get the desired result. As peak currents are more likely when heavier ingots are rolled, the rolling of plate and slab ingots was investigated. Conditions prevailing when smaller ingots are rolled can be deduced from the results obtained on heavier ingots. All measurements were made when plain carbon grades under 0.15 pct C were rolled. The motor current, the voltage across the armature, and the rpm were recorded simultaneously on synchronized charts, Fig. 1, which moved with the speed of 6 in. per min. Each draft was recorded by a special observer. The rpm curve made it possible to establish the acceleration at any given moment. For purposes of correlation, the maximum current during a pass and the corresponding acceleration were used. The charts made it possible to establish the position of the roller&apos;s lever at any given moment as well as the total time of a pass. The slab ingots were divided into three groups (28x35, 28x45, and 27Mx53 in. ingots) and each group was investigated separately. Since they account for most of the current peaks, only flat passes were used for purposes of correlation, a total of 1373 having been investigated.

Jan 1, 1956

By Frank Foote, Willard L. Bruner, Eric R. Jette, Y. New york

The alloys of gold and iron were investigated in 1907 by Isaac and Tammann,l who determined the thermal diagram for the entire system by thermal analysis and microscopic examination. They also reviewed the previous literature. Since that time the present authors have been able to find only two additional references. Guertler and Schulze2 examined the electrical resistance of iron alloys containing up to 40 per cent by weight of gold between 0" and 200" C.; the alloys were in the form of wires. The main result of this work was to confirm the solid solubility limit found by Isaac and Tammann; namely, about 20 per cent Au. More recently, Shih3 has examined the magnetic properties of gold alloys containing up to 10 weight per cent iron and particularly the range below 5 per cent. The alloys in the lower range were found to be paramagnetic; the 10 per cent alloy was ferromagnetic. The present investigation was undertaken to determine the solid solubility limits at various temperatures, particularly below the a-y transformation point of iron, since these solubilities are of some importance in connection with the working of the alloys in the manufacture of certain "grey" and "blue" golds. Materials and Methods The gold was obtained from the U. S. Metals Refining Co. and contained 99.99+ per cent Au. The electrolytic iron had been annealed in hydrogen and contained impurities as follows: P, 0.035; Si, 0.001; S, C, Mn, Cu, each 0.01 per cent. Weighed quantities of the two metals were placed in small crucibles lined with pure sintered MgO; a saturated solution of magnesium nitrate

Jan 1, 1934

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By Kung-Lee Wang, Brian W. Mackenzie, Warren E. Morrison, DeVerle P. Harris, George F. Sharrard

The term "mineral economics" is applied to a wide range of activities in the mineral industries. Earlier chapters have described the application of economic concepts to the mineral industries-supply, demand, conservation, tariffs, etc. The solution of mineral economics problems is often assisted by the application of quantitative methods. The purpose of this chapter is to describe a number of quantitative methods-econometric, operations research, and management science techniques-which find application in the analysis of mineral economics problems. These methods include input-output analysis, trend analysis, forecasting techniques, simulation, multivariate statistical analysis, mathematical programming, and market research techniques. The purpose of this introductory section is to provide a mineral economics framework for the application of these methods. Mineral economics is a subdivision of economics that is justified by a sufficient number of economic problems in the mineral industry requiring special experience and an unusual combination of skills. These problems are concerned with the conversion of minerals as geologic resources to minerals as economic goods. The mineral conversion process is outlined in Fig. 8.A.1. The physical occurrence of mineral deposits in nature and the market demand for mineral products in the economy provide the basic stimuli. The conversion process embodies a number of sequential stages-exploration, the development of mineral deposits, and mineral processing facilities and, consequently, productive activity to supply market demand. Changes in demand and the depletion of deposits illustrate the dynamics of the process. Mineral economics applies economic con-

Jan 1, 1976

By V. E. Dementyev

This paper presents a brief overview of some IRGIREDMET advances in gold hydrometallurgy. Original impulse-percolation technology and equipment for intensive cyanidation of gravity concentrates have been developed and introduced into industrial practice by IRGIREDMET since 1980s (RF Patents N1593250). The process is based on leaching using special hydrodynamic and reagent conditions providing high dissolution rate for coarse gold particles. Gold and silver are precipitated from pregnant solution by cementation or electrowinning. There was also proposed an im-proved cementation method using zinc in a contact with electrically conductive material. The units including closed water recirculation, tails detoxification and semi-dry tails IRGIREDMET is well experienced in gold adsorption technology using ion exchange resins and activated carbons. The comparison of CIL and RIL processes were done for a number of gold mines, for example for Sukhoi Log gold deposit. The properties of prospective foreign and domestic ad-sorbents including strong-base, bi-functional and weak-base resins as well as activated carbons were studied. The Institute has developed some adsorption/elution technologies and equipment, such as a two stage RIP adsorption technology for gold/silver ores, an improved technology for gold elution from loaded resin and carbon, electrowinning cells for gold recovery from RIP and CIP eluates etc. Large scale ?Resin In Pulp? tests using weak-base resin were finalized and process design criteria were developed. Gold plant design is on progress at the moment. Improved technology for carbonaceous (preg-robbing) gold ores was developed. It was tested for some gold deposits including Sukhoi Log. It allows to overcome preg-robbing activities of ores treated and to improve dramatically performance of cyanidation and adsorption circuits. The studies on refractory gold ore treatment including bio-oxidation, pressure oxidation, roasting and ultra-fine grinding were conducted. Heap leach technology was tested and introduced by Irgiredmet for a number of Russian mines. Zinc cementation, activated carbon and ion-exchange resin adsorption were used for gold recovery from pregnant heap leach solutions. The options including combined technology ?Heap leach/ RIL or CIP? for clay ores were also developed and tested. The plant using developed technology is at construction stage now. The study on In-Situ gold leaching was conducted. The comparison of different gold lixiviants for this purpose was carried out. Gold recovery from pregnant leach solution by activated carbon and anionite including gold elution from loaded adsorbents etc. was also studied. In 2000 the In-Situ leaching technology was commissioned at Maminskoye gold deposit (Ural). The technologies for treatment of complex ores and by-products were proposed. For example, the technology of gold, silver, copper and zinc recovery from calcines after sulphuric acid production was developed.

Jan 1, 2014

By Chan-ho Park

As the building has recently become bigger, higher, and freeform, a technology called BIM(Building Information Modeling), which is a key technology that integrates construction and IT(Information Technology), has been rapidly introduced and expanded. Because BIM technology offers various benefits, countries that introduced BIM early has been actively promoted. However, misperceptions of BIM are prevalent in countries such as South Korea that have adopted it relatively late, with lack of awareness of its fundamental purposes. Under these circumstances, transparent and quantitative performance assessment needs to be executed in order to eliminate the misperceptions, and to explain and revitalize the BIM introduction. These quantitative performance measure KPI (Key Performance Indicators) to be measured should be prioritized. As derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, Uses the BSC to seek a balance between short-term financial goals, values and the value of long-term goals. Uses the BSC(Balanced Scorecards) to derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, seeking a balance between the value of short-term financial objectives and the value of long-term objectives. Through this, the KPI (Key Performance Indicators) which is used for measuring the effect of the BIM will be generated and also the method that can determine whether the generated KPI figures are objectively inter-connected will be suggested as well.

Aug 1, 2013