Search Documents

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Hussin A. M. Ahmed

Oxidized coals are difficult to float. Therefore, in this paper, a special flotation procedure was investigated for upgrading this type of coal. The procedure is called direct contact flotation. It relies on mixing dry coal either with pure (anhydrous) flotation reagent(s) or microemulsion. By applying the new direct contact flotation procedure, a coal yield reaching > 95% using anhydrous flotation reagents was achieved, but with relatively high consumption of reagents (up to 30 g/kg). This high reagent consumption may be attributed to the fines included in the flotation feed (100% less than 0.5 mm, with 40% less than 75 µm). On the other hand, the clean coal yield was found to be approximately 88% when mixing dry oxidized coal with microemulsion droplets from dodecane and dodecyl tetra (ethylene glycol) ether (C12E4) in water at a total reagent dosage of 10 g/kg. The direct contact of coal either with unhydrous reagents or microemulsion also provided a high flotation selectivity.

May 1, 2012

By Sheldon P. Wimpfen

Under the Wilderness Act of 1964 and the accompanying House Conference Report, the Geological Survey and Bureau of Mines are charged with the responsibility of making recurring mineral studies of wilderness and wilderness candidate areas in national forests within and proposed for the National Wilderness Preservation System. The Wilderness Act, a major shift from the multiple-use concept of national forests, identified for the first time the value of mineral resource information in decisions for single-use designation of public lands. This concept was further realized when the Secretary of the Interior in May 1974 recommended that mineral studies be made prior to wilderness recommendations for five large Interior-managed game ranges and the Glacier Bay National Monument aggregating 7.8 million acres. Presently, our studies have been completed on 126 wilderness and proposed wilderness areas totaling 15.4 million acres in the national forests. In 1973, 1 year in advance of the act's 10-year review deadline, we completed the 34 primitive areas, originally the only potential additions considered by the 1964 Act.

Jan 1, 1975

By Z. M. Zavodni

The stability of waste dumps depends to a great extent on the physical properties of the underlying foundation. These physical properties are evaluated through surface geotechnical surveys, subsurface exploration, and field and laboratory testing. Sufficient information must be obtained to define and assess the strength, consolidation, distribution, topographic and hydrogeologic properties for these materials. Important foundation data collected in the field include: surface infiltration rates, downhole hydraulic conductivities, ground water levels, bedrock structural parameters, soil types and soil thickness. Laboratory testing should identify the classification, strength, moisture content, hydraulic conductivity, attenuation and consolidation characteristics. Summarized in this paper are procedures and typical results of porphyry copper leach dump foundation investigations. Laboratory properties and design recommendations for potenia1 foundation liner materials are described. Back analysis and laboratory foundation strengths are compared. The topographic effect of the foundation on dump behavior is discussed and a foundation pore pressure monitoring experiment at the toe of an active waste dump is described.

Jan 1, 1985

By P. P. Gregory

Natural petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the "pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the controlled methods of production and drilling, a portion of this gas is produced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grow rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures wereincreasing. Determination of Gas-oil Contact and Thickness of Gas Cap The gas-oil contact can be conveniently located in the process of drilling a well and by electrical logging. However, very little can be found in the petroleum literature concerning methods of predetermining gas-oil contacts in producing reservoirs. Therefore, the writer feels justified in describing briefly a simple, workable, and inexpensive method of determining gas-oil contacts and outlining the limits of gas-cap areas in a field where such knowledge may be essential for efficient production and development operations. The method involves the determination of the following data: (I) Structural data, such as the depth or elevation of the top' of "pay" horizon; (2) reservoir pressures; (3) tubing and casing pressures at the well head; (4) static oil-pressure gradient; (5) static gas-pressure gradient. These data can be secured with a minimum of expense, inasmuch as the

Jan 1, 1938

By Thomas D. Barkand

Investigation of several serious hoisting accidents identified machine brake failure as the most common cause. The recent revelation of this potential hazard has prompted regulatory authorities to require an additional, independent, emergency braking system. As a result of this initiative, a new generation of braking systems have been developed and applied to mine elevators. This paper will discuss the design and testing of an electrical dynamic brake, pneumatic rope brake, and traction sheave brake. The effect of compound braking on hoisting systems equipped with multiple brakes will also be addressed.

Jan 1, 1992

By Kurt Aasly, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

Seafloor massive sulphides (SMS) can serve as a potential resource of metals such as Cu, Zn, Au and Ag. SMS rock samples from the Loki’s Castle area at the Arctic Mid-Ocean Ridge are comprised of sulphide bearing minerals such as pyrite, chalcopyrite, isocubanite, galena, sphalerite, whereas the gangue consists mainly of barite and silica. Sphalerite, chalcopyrite and isocubanite show complex intergrowth textures on the nano- to microscale. Various mineral processing tests were conducted in order to recover copper, zinc and silver. It was shown that sensor-based sorting can be efficiently used for preconcentration of SMS rock samples. A significant amount of waste (i.e. barite and silica) was removed in the preconcentration stage with very low losses of copper and zinc to the waste fraction. The upgraded samples were sent to the next processing stages. The results showed that the complex mineralogy of the SMS material provided challenges to conventional mineral processing methods. Hydrometallurgical processing was applied as an alternative method for extraction of metals from SMS. Leaching experiments were conducted using solutions of different lixiviants, and it was shown that leaching of SMS together with manganese nodules would facilitate efficient recovery of metals from these resources.

Jan 1, 2018

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

By George S. Austin

Perlite is rhyolitic glass with 2 to 5 percent by weight (wt.%) bound water held within the silicic-glass structure. It is often distinguished by vitreous, pearly luster and concentric perlitic fractures ("onionskin"). Occurrences worldwide are associated with Tertiary to middle Quaternary volcanic rocks. Perlite is in silicic domes, plugs, laccoliths, flows, vitric tephra, chill margins of dikes and sills, and welded ash-flow tuffs. It is a hydrated volcanic glass formed through secondary alteration of obsidian by the incorporation of water into the glass/silica structure. Post-emplacement hydration (weathering) of cooled glasses by meteoric water is the principal alteration process, but some hydration by magmatic or meteoric water during or shortly after emplacement, or hydration by water exsolved during cooling may occur. Commercial "perlite" is any volcanic glass that expands or "pops" when heated quickly to plasticity while evolving steam and thus forming a lightweight, frothy material. The expansion temperature typically ranges from 1,100 to 1,500°F. An expanded volume increase of 10 to 40 times the original volume yields expanded densities of 1.5 to 11 pounds per cubic foot (lbs/ft3). Perlite is mined by eight companies at 10 operations in six western states. New Mexico accounts for more than 80% of the total tonnage mined. The rest comes from Arizona, California, Colorado, Idaho, and Nevada. In 1992, domestic production was 571,000 short tons (st), domestic apparent consumption was 591,000 st, and the value of crude perlite was $15.3 million. In 1991, with about the same production and price of crude perlite, the gross value for expanded perlite was $101.7 million. Perlite exports in 1992, primarily to Canada, are estimated an 30,000 st; and imports, from Greece, are an estimated 50,000 st. In 1992, 70 plants in 33 states expanded crude perlite. Construction uses of expanded perlite accounted for 66% of total domestic sales. Expanded perlite used as filter aid accounted for 15%. All other markets, including use as a filler and in agriculture, accounted for 19%. Leading states for expanding perlite, ranked by order of sales, were Mississippi, Pennsylvania, California, Illinois, and Georgia. Domestic perlite encounters transportation disadvantages in some areas of the eastern United States compared to perlite imported from Greece. However, western U.S. perlite exports to Canada offset this in large part, and net import reliance for perlite is about 3% of domestic consumption. Perlite grab samples were tested at the New Mexico Bureau of Mines and Minerals Resources (NMBMMR) for their basic suitability in horticulture, construction, filter aids, and fillers/extenders using Perlite Institute techniques modified by the NMBMMR. Most commercial perlite ranged from 2.5 to 3.0 wt.% bound water for all major types (classical, granular, and pumiceous). Expanded density varied widely, but the lowest density of 1.9 lbs/ft3 was for granular. Average brightness of expanded perlite was 47.6 to 69.3%. Nonexpansibles, commonly obsidian or "dead" perlite, ranged from 18 wt.% to less than 1 wt.%, with granular perlte generally the lowest. Compacted density was not related to either perlite type or nonexpansibles present. Sieve analyses of the -50+100 mesh product showed that, in general, pumiceous perlite produces more fines and classical and granular perlite average 60 to 80% -30+100 mesh after expansion. Samples were tested for crystalline silica that ranged from below the detection limit of 0.5 wt.% to nearly 0.2 wt.%, but most tested below 0.5 wt.%. Although quartz content can be lowered in the expanded product by the expansion process, producers can further lower crystalline silica in the product by mixing low-quartz crude with high-quartz perlite before expansion. Chemical analysis by x-ray fluorescence confirms the rhyolitic composition of perlite, but indicates that surface weathering may increase the concentration of some elements, such as potassium and calcium, by infilling cracks or fissures developed during or after perlite emplacement.

Jan 1, 1995

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By C. Richard Tinsley

Mineral economists debate whether to call the deep-ocean nodules "manganese nodules," "nickel nodules," "polymetallic nodules," or even "ferro-manganese nodules." It is nickel and copper that are generally regarded as the main targets in the nodules. Processing considerations are thought to virtually dictate that Deepsea Ventures will produce high-purity manganese metal (at least if it follows a hydrogen chloride leach), whereas other groups have been focusing on the selective extraction of copper, nickel, cobalt, zinc, and molybdenum, while rejecting manganese to tails. Solvent extraction appears to be the primary multimetal extraction technique (except for manganese). These processing considerations indicate that metal production f, or Deepsea Ventures is essentially a co- product system (manganese recovery is necessary to recycle chloride ions) while the other groups can more easily approach the metals as selective co-products (e.g. recovering nickel and copper, and rejecting cobalt). Some zinc may be produced as a co-product, as it may have to be removed in the solvent extraction process.

Jan 4, 1975

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

By J. F. Leroux

The Gaspé smelter at Murdochville, Quebec, Canada introduced concentrate injection into elongated Peirce-Smith converters sized 1.96m x 12.5m (13 ft. by 41 ft.) in 1996, and commissioned a large, converter-like bath smelting vessel in April 1998. The new vessel, which is sized 4.27m x 16.1 5m (14ft. by 53ft.) has several interesting features designed to effectively utilize bath smelting technology for the requirements of the Gaspé smelter. For example, the vessel can operate on concentrate injection at upwards of 60-80 tph rate on an instantaneous basis, can operate as a large Peirce-Smith converter, while it is also fitted with matte and slag tapholes much akin to Noranda Process reactor, and includes a novel cold charge addition system. The new technology will eventually allow the capacity of the plant to increase from about 300,000 tonnes of concentrate per year to over 350,000 tonnes of concentrate per year while improving sulfur capture.

Jan 1, 1999

By F. C. Eberhardt

Systematic planning of underground work is increasingly important in this era of advancement of rapid underground excavation techniques. The day when planning consisted of deciding which men would shovel and which would push wheelbarrows - and the answer to any problem was more men - has faded into the past. The modern underground constructor faces economic and competitive conditions which demand exacting planning, logistics and scheduling; the most efficient operating methods and equipment known; and realistic, comprehensive, analytical risk evaluation with adequate contingencies or other protection. Proper planning to cover all these elements - plus one other element: old fashioned "good luck" - will insure a successful underground project. Underground work, because of its inherent characteristics, is among the most risky types of construction. The forecasting of underground conditions is at this time only educated predictions based on sometimes faulty data, insufficient data, or no data at all. The predicted conditions of numerous operations have deviated far from the actual conditions encountered. Opportunities for error exist in profusion seldom present for surface operations. Other than this unusual risk factor, the planning for underground work does not differ greatly from planning for surface work. In planning and starting an operation there is seldom available the information or time to thoroughly analyze all unknowns. It then becomes necessary to develop a plan predicated on assumptions and trade-offs that appear to be safe and economical and to add time and cost contingencies that will provide some degree of protection. On competitively bid fixed price work, choice of markup on estimated

Jan 1, 1974

By Ruston A. Ford

This paper reviews the development of the David Bell Mine, from early exploration, through discovery, construction, start-up, underground development, and production. Details are provided regarding the mine development, the mechanized cut and fill stope production, the proposed long-hole stoping with delayed backfilling mining method for the lower levels and the cyanide leach carbon-in- pulp concentrating process. The mine development remains on schedule and under budget with results very much as predicted in the feasibility study.

Jan 1, 1987

By James Pennington

[The Mining and Metallurgical Divisions of the Bureau of Mines, Region V, conducted an investigation in 1950-51 of the iron sulfide deposits in Aitkin and Carlton Counties, Minn. Twelve diamond-core-drill holes, aggregating 2,347 feet, were drilled in secs. 14 and 15, T. 46 N., R. 25 W., Aitkin County, to increase reserves of iron sulfides known to exist 2 miles southwest in secs. 28 and 29, T. 46 N., R. 25 W. Three diamond-core-drill hobs, totaling 561 feet, were drilled in Canton County, sec. 7, T. 46 N., R. 2 0 W., to check reports of the presence of a large sulfide deposit in that area. Mineral-dressing tests were made on cores from 10 holes drilled in Aitkin County. These included core from hole 21 drilled in sec. 28 and submitted by the Glen Development Co.]

Jan 1, 1953

By John B. Hastings

Ten miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake-beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; bat this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. This section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September

Jan 1, 1909

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

By Dupuy. Leon W.

"INTRODUCTION For many generations the Indian tribes of the southwestern deserts knew of the thermal springs of the Coso District in southwestern Inyo County, Calif. Belief in the reputedly healing qualities of the waters and muds of the area was widespread. F. J. Sanders discovered mercury in the siliceous sinter around the hot springs while he was exploiting the district as a health resort. In searching for new domestic sources of supply of strategic minerals, authorized under the Strategic Materials Act, 3/,the Geological Survey 4/ first examined the deposits, which were drilled and sampled by the Bureau of Mines in the spring of 1941.The deposits investigated comprised three units known, respectively, as The Devils Kitchen, Nicol, and Wheeler. Most of the work was done at the first two.Of particular interest in the Bureau's work on the project was the adaptation and use of the bucket drill as a tool for sampling shallow, soft ore deposit."

Mar 1, 1948