Search Documents

By E. D. Goddard, D. S. Murphy

Acid resistance, zeta potential and ESCA (electron spectroscopy. for chemical analysis) experiments were performed on emperador marble and four calcium carbonate samples (onyx calcite, travertine calcite, Iceland spar calcite and aragonite). Six fluorine-containing reagents were used to treat the surfaces of these materials: magnesium hexafluorosilicate, zinc hexafluorosilicate, sodium fluoride, zinc fluoride, strontium fluoride and stannous fluoride. The acid resistance of treated samples proved to be much higher than that of their untreated equivalents. The isoelectric point of treated samples approaches the isoelectric point of fluorite. Also, the fluorine content, as measured by ESCA, of a marble surface treated with magnesium hexafluorosilicate is much higher than that of an untreated sample. The binding energy off of fluorine and calcium the treated marble is consistent with the formation of calcium fluoride.

Jan 1, 1994

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By KNona C. Liddell

The time and spatial dependence of component and species concentrations during in situ uraninite leaching have been modeled using a reactive transport model based on partial equilibrium between reactive minerals and the solution. The flow field is represented by mixing cells in series. The effects of the H2O2, (NH4)2CO3, and NH4HCO3 component concentrations have been simulated, and results are presented for a one-dimensional flow field.

Jan 1, 1995

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By C. F. McCarroll

[Laboratory research and, control in the production an. utilization of petroleum and it 3 products have expanded greatly during the past decade, and much of the routine control and experimental equipment now rewires the constant daily use of liquid mercury. In spite of this ;;renter use, very little consideration has been given to the hazard that might be occasioned by the toxic vapors of mercury unavoidably spilled' of otherwise exposed to the atmosphere during the normal procedure of laboratory open at ions. A simple visual examination ).'.' son-,, r° the laboratories reveal the presence of a considerable quantity of mercury in the cracks of floors, on work tables, and on ark, around equipment stands. Usually this mercury is contaminated with oil3/ and dirt so that it remaining in a finely divided state and a ;mall amount pre presents a relatively large surface for evaporation. Since :mercury shows measurable volatility at a temperature v,.^ lo.! 5o F., mercury vapor will be present in, the mercury _3 exposed promiscuously.]

Jan 1, 1939

By Theo. Koulomzine

"The property of Consolidated Central Cadillac Mines, Limited, consists of 1,103 acres formerly held by Central Cadillac Mines, Limited, and Wood Cadillac Mines, Limited. Both mines have been partly developed to depths of 565 and 1,000 feet respectively, and from 1939 to 1943 they produced gold, with small amounts of silver and tungsten, having a total value of $2,208,528 from 377,489 tons of ore. The average grade of the ore was $5.85 a ton . Less than 10 per cent of the ore hoisted was discarded by sorting. New development work, carried out since the former Wood property has been purchased by Central Cadillac, has shown that the tonnage indicated by mine workings and diamond drilling exceeds 2,000 tons per vertical foot.The property lies between the claims of Kewagama Gold Mines, Limited, and Pandora Cadillac Gold Mines, Limited, and straddles the Cadillac 'break' for a length of nearly 1 ½ miles. The main workings are 1 3/4 miles east of the well-known O'Brien gold mine.GEOLOGYOutcrops are very scarce, with none at all of the most important horizons, so that the general geology shown in Fig. 1 is deduced mostly from underground workings and diamond drilling. Fig. 2 is a vertical cross-section and Fig. 3 a longitudinal section through the ore zone.The ore lies within a belt of Blake River volcanics which is approximately 600 feet wide and is flanked on the north and south, respectively, by Cadillac and Kewagama sediments. All the formations have a nearly vertical attitude. The Blake River belt consists essentially of well sheared volcanic tulfs, but associated with these in the northern part are a number of bands of iron formation and the central part, to a width of 100 feet, is occupied by talc schists, making the Cadillac fault proper. Intruding the volcanics south of the Cadillac shear zone are dykes of two types- finegrained aplite or quartz albitite, and porphyry; both consist essentially of albite and quartz and are distinguishable only by the grain size. They have the general east-west trend of the formations they intrude."

Jan 1, 1954

By Q. Han

Irradiation of high energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs (ORNL) and Purdue University on using high intensity ultrasonic vibrations for degassing molten aluminum, processing particulate reinforced metal matrix composites, refining metals and alloys during solidification process, welding, and producing bulk nanostructures in solid metals and alloys.

Jan 1, 2014

By William H. Grady

FactoRs entering into the market value of coal are its grade, and the cost of labor, material, and capital. Reduction in these costs cannot be expected in the future, and it therefore follows that greater economy in their use must be accomplished if it is desired to hold the present markets; more tons of product per unit must be obtained in a given time from both men and material, and means devised for increasing the percentage of lump and domestic sizes. This paper is presented for the purpose of inviting discussion and stimulating thought in regard to the influence of methods of procedure and plans of mining, upon the quality of coal, the economical use of labor, material, and capital, and the cost of production. Even the better methods of the present day leave much to be desired, and a review of the reasons and necessities for their use may be of value in pointing the way to more economical mining. The writer does not attempt to discuss untried methods of mining, but rather to state clearly and concisely a summary of the results obtained under the several methods of procedure that have been adopted. In some instances a high degree of concentration has been effected, and comparisons of the results obtained with the results of lesser degrees of concentration form an interesting study. It is believed that much may be accomplished in improving the quality, and in the more economical use of labor, material, and capital, by concentration, and it is to concentration in particular that your study is invited. The writer, who has occasion to visit many mines, most of which are under different management, has been inclined to the opinion that improvement has been retarded in many ways and that mining has not as yet been entirely freed from the early-day practices which were forced upon it. Practices resulting in lack of concentration, to which reference will be made, are: The absence of robbing, necessitating the frequent interposition of barrier pillars; lack of system and of proper supervision, resulting in losses of life and coal. These practices could not well be

Jan 1, 1915

By H. B. Prinsloo

Change management and training initiatives in remote rural settings in Africa are generally difficult to implement successfully due to factors such as varying levels of education, multiple nationalities and languages as well as cultures in one workplace. The challenge has always been the ability to implement change management and training initiatives that will have an impact despite these differences. Essentially this requires that the change and training interventions employed are applicable and should work well with a wide range of individuals sitting in one room ? in practice this can vary from semi-literate workers to engineers with PhDs. In this paper we will share the theory behind behaviour-based change management and training and present a case study that reviews an actual supply chain improvement and sustainability implementation at a Zambian copper mine. The case study explains the results achieved as well as the interventions employed to achieve these results in a multidimensional organizational environment. This paper is relevant to delegates who are faced with implementing changes or training in a similar mining environment. Keywords change management, behaviour-based training, learning style, P2P process.

Oct 1, 2013

By G. Castillo, G. Thies, C. Bissue

"Newmont’s Phoenix mine began gold production in 2006 and has since experienced difficulties in reaching design throughput due to variability in ore hardness. In 2010, a debottlenecking study was conducted, generating multiple options to increase throughput of the existing Phoenix Mill through a series of phased expansions. An option was selected in early 2011 to increase the current concentrator capacity by approximately 25% through two phases. The first phase of the project was the installation of a secondary crushing and screening circuit in order to reduce SAG feed size from a P80 of 6 inches to 2 inches. The second phase focuses on downstream unit operations in the concentrator aiming to relieve existing bottlenecks such as flotation. This paper analyzes the design, commissioning, and operation of a recently installed SAG Pre-crush circuit (Phase 1). The design discussion will focus on concept development, flowsheet design, design criteria, process models, design limitations, and control philosophy. Discussion on the integration of operating data and flowsheet into design during engineering will be presented. Actual operating data of major equipment is gathered from the commissioning and operation of the circuit and compared to the initial design models. Conclusions will be drawn on equipment design factors used during engineering, and the success of model integration into operation. The paper concludes on the successes of the project and where improvements can be made during design.INTRODUCTIONThe Phoenix mine is located within 25 miles of the town of Battle Mountain, Nevada. The mill processes copper, silver, and gold ore. Production started in 2006 and has since struggled to reach the designed tonnage of 33,600 stpd due to the variability in ore hardness. In production year 2010-2011, the Phoenix mill average daily throughput of 33,000 stpd. In 2008, a larger primary crusher (FLS 60/89 gyratory crusher) was installed to operate in parallel with the originally supplied primary crusher (Metso 50/65 gyratory crusher), in order to provide additional capacity upfront in the circuit so that the primary crushing circuit could keep up with the mill.In 2010, a mill debottlenecking study was completed to assess the various options that could be implemented to increase the current mill capacity. The study was completed in late 2010 and contained four tonnages that Phoenix could achieve through various expansion scenarios. A single option was selected in early 2011 to increase the mill capacity from 33,000 stpd to 48,000 stpd. The selected option looked at a four phased expansion that would increase the capacity of the Phoenix mill and address the mill’s current bottlenecks:"

Jan 1, 2013

By R. L. Bruening, N. E. Izatt, S. R. Izatt

"Rare earth elements (REE) are essential and unique components of many high-technology products without which functioning of modern society would be greatly impaired. Commercial deposits of REE are limited to a few geographical locations. Largely untapped sources of REE are available in endof- life (EOL) magnets, rechargeable batteries, and electronics. Presently, < 1% of REE in EOL wastes is recycled. Conversion of EOL wastes to liquid streams allows use of IBC’s Molecular Recognition Technology (MRT) process to selectively recover, separate, and purify target REE and associated metals at g/L to mg/L or lower concentration levels. The MRT process together with its applications to separations of REE and associated metals in recycling as well as in mining are described. Economic and environmental advantages of MRT are presented. INTRODUCTIONRare earth elements (REE) include the lanthanide series (La-Lu), Y, and Sc. These elements are not rare, but concentrated minable deposits are scarce (Cordier 2012; Haxel, Hedrick, & Orris, 2002). Over 95 % of the world’s supply of REE is controlled by China (Hanson, 2011a) where they are mined, processed, and the pure elements incorporated into a growing number of consumer and military products. The consumer products are marketed worldwide. Since REE are vitally important in consumer and military products, this situation has caused other nations to scramble to develop the capability to produce their own supply (Cordier, 2012).In the U. S., Molycorp has reopened the Mountain Pass REE mine in California and production has begun (Goldenberg, 2010). Development of a reliable internal source of REE is of high national priority in the U.S. (Hanson, 2011b; Hess, 2012: “Obama Announces”, 2012). These elements have in recent decades been incorporated into new consumer and military products that are essential to our economy and defense. These products range from wind turbines, high performance magnets, hybrid car rechargeable batteries, energy efficient lighting electronics, flat screen televisions, and smart phones to advanced weapons systems (Haxel et al., 2002; Levkowitz & Beauchamp-Mustafaga, 2010)."

Jan 1, 2012

By P. Grainger, P. G. Kalaugher

Paper presented at conference and first published in preprint volume of: Risk assessment in the extractive industries, held in University of Exeter, 23-24 March 1994. London: IMM, 1994. Large, unpredicted ground movements resulting from open cast or underground mining present risks to the safety and economy of extractive industries. As large, sudden failures are usually preceded by small displacements at a much slower rate, the detection and monitoring of these minor changes to the ground surface provides a means of assessing the risks. It is recommended that a visual approach is often preferable to surveying or fixed instrumental measurements. An optical system has been devised, incorporating a 35 mm camera, which allows an immediate comparison on site between a colour transparency taken on a previous inspection and the scene it represents. The observer fuses the transparency stereoscopically with the directly viewed scene. The impression is close to that of normal vision except that differences in detail which have occurred since the transparency was taken are immediately obvious, enabling a qualitative assessment of changes to be made on site. If repeat photography is required it can be taken with exactly the same alignment and coverage. The two images are then available for office analysis using simple micro-photogrammetry

Apr 1, 1996

By Juan Villegas González

La caída de rocas, es causa común de accidentes muy graves en las operaciones mineras. En ese sentido, la disminución de este riesgo involucra un compromiso íntegro y responsable de la Dirección General, personal de dirección y administración operativa, así como de todos los operadores de la Unidad Minera "La Colorada", México. Por ello, el presente texto describe la aplicación de métodos seguros de trabajo en el soporte de la roca de la mina "La Colorada", así como la capacitación a todo el personal, selección de equipo y materiales adecuados para desarrollar la actividad minera de una manera segura y sin pérdidas humanas.

Sep 14, 2009

By Foster Bruner

Jul 20, 1956

The central question concerning the health risks associated with mining and processing of taconite ores in the Eastern Mesabi Range is ??does asbestos, of any variety, occur within the gangue mineral population?? Free silica in the form of quartz does exist in the taconite, but silicosis has been relegated to a secondary issue. The focus has shifted to the asbestos minerals and the malignancies that might occur following low-level exposure to dust. Although mineral fibers do exist in the Mesabi taconite ores, Ross, Nolan and Nord conclude ??no asbestos?, as explained in their contribution ??The Search for Asbestos within the Peter Mitchell Taconite Iron Ore Mine, near Babbitt, Minnesota?. Their area of study is located in the eastern Mesabi Range. It is here that the tectonic and metamorphic effects associated with the intrusion of the Duluth Gabbro have been profound. A variety of amphibole minerals have developed as a result of these geological events, some with names recognized within the US Asbestos Standard. The issue tackled by the authors is whether or not these amphiboles are present in the mine and if so whether or not they are asbestiform in habit.

Jan 1, 2008

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015

By D. A. Sullivan, D. W. Fuerstenau

The authors investigated the comminution of quartz and limestone mixtures in a ball mill, showing that the distribution modulus of a comminuted material is the same whether it is ground separately or as part of a mixture. Analysis of the ground products indicates that quartz and limestone consume energy during ball milling in proportion to their mass fraction in the mixtures. Recently Schuhmann&apos; made a significant contribution to comminution theory by proposing that complex comminution operations comprise the summation of many individual comminution events. By means of the single comminution event hypothesis, Schuhmann derived the Charles energy-size reduction relationship by considering that fragments of every particle crushed during a single impact have a size distribution characterized by the Schuhmann size distribution. In this paper, the size reduction of mixtures of solids in ball mills is analyzed by considering that size reduction occurs as many single comminution events. If a mixture of two materials is being ground in a ball mill, each successful impact of a ball with a particle of one material should yield an assembly of particles whose size distribution is characteristic of that material. Considering both materials to follow the Schuhmann size distribution equation, the size distribution of material 1 in the product is Where y is the weight percentage of material 1, which

Jan 1, 1962