Search Documents

Jan 1, 1879

By Thomas D. West

The fact that iron expands when heated, until fusion takes place, and that molten iron is consequently less dense than solid iron of the same grade, is now universally admitted. It was proved by the extensive experiments of Mr. Thomas Wrightson, reported in the Jownal of the Iron and Steel Institute (1890, No. 1, p. 72, and 1891, No. 1, pp. 75, log), and, in a manner, is illustrated in heavy founding by the shrinkage 'of the molten metal, which must be " fed " in order to obtain solid castings. This decrease in volume requiring " feeding" while the metal is still liquid I call " shrinkage," applying the term " contraction" to the decrease in volume which takes place after solidification, while the iron is cooling to atmospheric temperature. The light-work founder, not having the opportunity to make heavy castings, in which shrinkage can be observed, is apt to confound the two; but they are in fact distinct, and are separated by an act of expanion, which takes place at the moment of solidification. The fact of this expansion was first practically demonstrated by Mr. John R. Whitney, of Philadelphia, Pa., whose experiments are recorded in the National Car and Locomotive Builder of May, 1889. Experiments recently made by the writer indicate that there is a constant relation between this expansion and the preceding shrinkage and forcibly demonstrate the necessity of " feeding " a casting to make its interior solid. This is a matter with which all makers and users of castings have experienced difficulty. The founder being heretofore unable to define correctly the principles involving the urgent necessity of " feeding " has failed to impress the moulder with its importance in making sound castings.

Jan 1, 1897

In the extraction of level bridge pillars in the South Mine by square-setting methods the general practice is to work transversely from the hanging wall in narrow sections three or four sets wide to the depth of the bridge-usually three sets. When the working block attains an area of twelve square sets, sand filling is run in, either by pneumatic (Proceedings No. 123, 1941) or hydraulic methods, in order to control the settlement of the general area and prevent the development of undue weight in the stope. Upon completion of the filling operations, or coincident with them, ore breaking is resumed and the transverse section of the bridge pillar gradually reduced. A number of these parallel sections may be working at the same time.In preparing a block of sets for filling a great deal of paddocking is required, both to contain the filling and to preserve access to ladderways and ore chutes which may be situated at some horizontal distance. Stope paddocking until recently was constructed of 10 in. x 2 in. boards nailed...

Jan 1, 1942

By L. O. Brockway, W. C. Bigelow, J. A. Amy

Specimens of Inconel-X alloy solution-treated at 2050°F and aged for periods of 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F have been examined by electron microscopy and by electron and X-ray diffraction. Four minor phases were identified: titanium nitride, niobium nitride, an M23C6 complex carbide, and the intermetallic ? phase. The two nitrides were found in all of the aged specimens and in the solution-treated alloy, the y' phase formed at all aging temperatures, while the M23C6 carbide formed only on aging at 1200° and 1400°F. Variations in the hardness, rupture strength, creep strength, and yield strength of the alloy have been shown to be related to variation in the size and distribution of the particles of the y' phase within the matrix grains of the alloy, with maximum values of these properties occurring when there is a maximum amount of the phase present and a fine state of dispersion of the particles prevails. THE nickel-chromium alloys containing titanium and aluminum are widely used in applications requiring high strength at elevated temperatures. Studies on relatively simple ternary and quaternary alloys'-4 have indicated that the favorable high-temperature properties of these alloys are related to the precipitation of an intermetallic ?'-phase having a structure based On that of the Ni3A1 phase of the nickel-aluminum system. The present investigation was undertaken to identify the minor phases and to study the microstructural changes occurring in one of the more complex commercial alloys as a result of aging in the service temperature range, with particular emphasis on investigating the role of the ?' -phase. The microstructural changes were studied by electron microscopy and the minor phases were identified by X-ray and electron diffraction. MATERIALS AND METHODS Inconel-X alloy was selected for this investigation because the previous studies of Frey, Freeman, and white6 provided extensive information on the variations in metallurgical properties of this alloy resulting from high-temperature aging treatments. Specimens aged 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F were made available for the present use. These were taken from 1-in. round-bar stock of a commercial heat having the following weight composition: 0.04 C, 0.56 Mn, 6.59 Fe, 0.007 S, 0.38 Si, 0.03 Cu, 73.22 Ni, 14.97 Cr, 0.78 Al, 2.38 Ti, and 1-02 Nb. They were solutjon-treated at 2050 for 4 hr and then water-quenched prior to aging. Powder X-ray diffraction patterns were obtained from insoluble minor phases which were separated from the alloys by digestion in the reagent of Mahla and Nielsen.6 Back-reflection patterns were obtained from electrolytically polished surfaces of the bulk search to detect the ?'-phase' Cu-K a radiation was used in both cases. In the electron-diffraction studies, the general method developed by Heidenreich, Sturkey, and

Jan 1, 1959

It is now becoming mandatory in Australia to rehabilitate ponded fine grained coal mine tailings, which may well have been deposited initially with no consideration as to how or whether this could be done nor to the costsinvolved. Of prime importance to the rehabilitation of tailings ponds are the bearing capacity and deformation characteristics of the tailings. Since the tailings are fine grained, time effects will govern the self-weightdeformation of the tailings initially deposited as a slurry and the subsequent deformation of the deposit under the weight imposed by rehabilitation fill. The engineering properties of a particular deposit of ponded tailings havebeen investigated and its response to the placement of fill monitored and analysed.

Jan 1, 1987

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By T. Urbancic, Eric von Lunen, G. Viegas, A. Baig

"The characterization of the failure process of induced fractures by hydraulic stimulation is fundamental to understanding the generation and evolution of the discrete fracture network within the reservoir. A more detailed analysis of the fracture mechanism can be a powerful tool for identifying fluid flow paths and proppant placement within the reservoir. For example, during the rupture process the energy release is partitioned into different physical processes for which the relative ratio is changed by the presence of fluids or rotations in the local stress field with relation to the frictional resistance in the fracture plane. Fractures occurring in the same host rock under the same stress conditions are expected to rupture similarly, independent of their size (self-similarity). Changes in the scaling relationships of fractures are indicative of a change in the failure process, host rock or in-situ stress. Correlation of failure process data with reservoir rock properties and the in-situ stress field will help identify regions within the reservoir with characteristic types of failures. Further correlation with hydrocarbon production data can be used to develop efficient treatment plans and production diagnostic tools.In this study we investigate the failure process of ~27,000 microseismic (M < -1) fractures induced during a hydraulic fracturing shale completion program in NE British Columbia, Canada by estimating static and dynamic source parameters, such as dynamic and static stress drop, radiated energy, seismic efficiency, moment tensor, fracture plane orientation, slip direction and rupture velocity. On average, the microseismic events have low radiated energy, low dynamic stress and low seismic efficiency, consistent with the obtained slow rupture velocities. Events fail in overshoot mode (slip weakening failure model), with fluids lubricating faults and decreasing friction resistance. Events occurring in deeper formations tend to have faster rupture velocities and are more efficient in radiating energy. Variations in rupture velocity tend to correlate with variation in depth, fault azimuth and elapsed time, reflecting a dominance of the local stress field over other factors.Further identification of spatial and temporal distribution of families of events with similar characteristic rupture behaviors, based on either rock formation, depth, source type, fracture plane orientation, stress drop, pad or proppant stage, may be used as a proxy for specific fracture network development and hydrocarbon production. This information may be used to determine reservoir properties, constrain reservoir geo-mechanical models with measured physical parameters, classify dynamic rupture processes for fracture models and improve fracture treatment designs. These will be the focus of future studies."

Jan 1, 2015

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does&apos; not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By J. Morgan Clements

The manufacture of coke in Peru, as practiced at the coalmines of the Quishuarcancha and Goyllarisquisca districts, is intermediate between the primitive coke-heap and the bee-hive oven. The method of coking is quite simple. In constructing the coal-heap, preparatory to burning, the ground is first leveled, and a simple stack of stone and clay is built, giving the bottom, to a height of 6 ft., approximately 6 ft. of external diameter. The size of the stack varies in different districts, but is generally 9 ft. high, and slightly smaller at the top than at the bottom. The walls of the heap are from 12 to 14 in. thick, which allows an inside diameter of from 3.75 to 4 ft. These walls are pierced at intervals by three or more tiers of openings or flues, connected with the central flue. The radial flues have a diameter of about 5 in. and are built with a gentle upward slope. The stack (shown in Fig. 1) is permanent; and in this respect the practice in Peru differs from other primitive practices in which nothing is permanent except the yard. Above the permanent 6-ft. portion of the stack there is added a cap of clay, about 3 ft. high, which contracts toward the top, where it has an inside diameter of about 2 ft. This clay cap is temporary, and frequently has to be renewed after each burning. Before charging the coal, there are first built, from the lowest tier of flues upon the ground, a number of temporary flues, leading from the central stack out to the edge of the coal-heap, and constructed of blocks of coal for the greater part of the distauce, the outer edge alone being of rough stoue. The coal is then piled up over these flues and around the stack to a height of about 6 ft. The bottom flues are the only ones that

Jan 1, 1905

By F. M. Doyle, G. Sidhu, A. J. Dussault, A. Raygani

There is a growing demand for rare earth metals for use in high strength permanent magnets, most notably Nd2Fe14B. Rare earth metals are extremely reactive, with reduction potentials around -2.5V SHE, and are conventionally produced by molten salt electrolysis. The current work was done to investigate an earlier report of electrodeposition of a neodymium ferroalloy from aqueous solution, to determine whether this approach could be an environmentally and economically competitive commercial approach for producing feedstock for permanent magnets. Such a process would be analogous thermodynamically to the Castner- Kellner process, in which aqueous sodium chloride brine is electrolyzed in cells with mercury cathodes. Metallic sodium forms an alloy (amalgam) at the cathode, thereby lowering the activity of the metallic sodium significantly below unity and making the reduction potential of sodium significantly less negative than the standard reduction potential. Here we report the effects of Nd/Fe ratio in the electrolyte, current density, temperature and two different complexing agents, glycine and cysteine, on the composition and morphology of the electrodeposits, along with current efficiency. The energy needed to produce neodymium as Nd:Fe alloys by aqueous electrodeposition was compared with values estimated for production by molten salt electrolysis and the thermodynamic energy requirement.

Jan 1, 2014

For a nation whose mining industry has generally been floating through history in the shadows of major mining developments elsewhere in the world, Australia has in the decade of the Sixties made a convincing bid to be one of the world&apos;s great "store- houses" of minerals. In fact, at the rate things are developing Down Under and Out Back, what with professional prospecting teams crisscrossing the continent under the direction of professional exploration management, Australia may one day find itself as the world&apos;s greatest storehouse. Whereas Necessity may be the Mother of Invention, Consumption is surely the Mother of Exploration. At least this is true in Australia of today. First, the forecasted shortage of iron ore in the world led to the fabulous discoveries in the Pilbara district of Western Australia. Now, the demand for nickel has generated even more interest among mining companies in the vast, untapped potential of Australia.

Jan 10, 1968

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Albert Hayes

FOUR mines at Wabana, on Bell Island in Concep-tion Bay, Newfoundland, produced 1,209,777 tons of ore in 1927, and it is expected that the produc-tion will be larger in 1928. The ore is a stratified oolitic hematite of sedimentary origin. Three workable beds and many thin beds occur in a thickness of 400 ft. of interbedded sandstones and shales. It is not profitable under present conditions to mine extensively in ore beds less than 4 ft. thick. The iron ore beds outcrop on the small island and are inclined northward more steeply, than the slope of the ocean bottom. The mine work-ings follow the bedded ore below the sea bottom, No. 3 Mine extending about 2 miles north of the island. At this point there is a cover of 1500 ft. of rock and 600 ft. of ocean water. It is impracticable to operate drills in the ocean to prove the extent of the submarine orebody in advance, and diamond drilling from the mine workings is the only method of exploration. Bell Island has been settled for a long time and a monument at Cupids, near Brigus at the head of Conception Bay, commemor-ates the tercentenary of a settlement there in 1611 by Captain Guy of England. was one of the chief ports of Newfoundland for deep sea fishing and doubtless many a captain wondered about the red rocks as he sailed past. The famous geologist, J. B. Jukes, records seeing a bright red sandstone 8 ft. thick on the northwest side of Bell Island during a visit in 1842, but he evident ly did not try to land on that rocky coast to get a sample. The iron ore is plainly visible in the high cliffs along the coast of the island, as bright brown layers interbedded with gray and white sandstones and dark shales. The heavy red rock was used by the fisher-men as anchor weights for fish nets and small boats, but its real value, so the story goes, was discovered by a merchant in Saint John,

Jan 8, 1928

Vast quantities of cosmic material, ranging in size from fine dust to large meteorites and planetoids, have been colliding with and accumulating on the earth since its origin 4.5 billion years ago. There are less than twenty well preserved meteorite craters and Jess than thirty fossil craters or astroblemes on the present face of the earth. On the moon, there are approximately 200,000 craters on the visible face alone -the largest crater being 132 miles in diameter and attaining a depth of 16,000 feet. Making allowances for the different physical conditions on the moon and assuming that these lunar features are of impact origin, the indifference is that, since primeval time, large numbers of celestial objects have also encountered the earth, but that both the topographic expression of the impact and the objects themselves have been destroyed by weathering and erosion. It may be reasonable to suggest that additions of cos-mic bodies have materially altered the chemistry of the earth&apos;s crust from place to place and that the impact of large meteorites and asteroids has created zones of weak-ness in the crust that could be the center of magmatic intrusion and mineralization.

Jan 1, 1965

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By P. Condori

Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken. A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material. Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores. This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit.

Jan 1, 2012

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

By M. N. Shetty, A. C. D. Chaklader

RECENTLY, it has been demonstrated that a considerable densification and interparticle bonding can be achieved if a pressure is applied to a powder compact while the material of the compact is undergoing either a decomposition reaction&apos; or a polymorphic transformation.&apos; The term "reactive hot pressing" has been coined to identify this process in which a phase change is combined with pressure to achieve interparticle bonding. This process is based on a principle which postulates that there is an enhanced reactivity and mobility of the molecular species at the phase-transformation temperature and this effect is utilized for interparticle bonding in powder compacts. This note summarizes the results obtained in an attempt to utilize this technique to produce ceramic-metal composites. In this case, a decomposition reaction of a compound (which after decomposition yielded an oxide) was used to achieve interparticle bonding in ceramic-metal composites. The reactive hot pressing was carried out in a Phillips induction heating unit, using either a graphite or a high-temperature steel die which functioned as both the susceptor and the hot-pressing component. The die was heated to the desired temperature in a helium atmosphere. All cermets produced by this technique were based on alumina as the ceramic phase. Different metal phases such as iron, copper, and chromium were used to study the effect of varying the metal phase on the properties of the composite. a Mono-hydrate (Boehmite) was mixed with different proportions of metal powders (-325 mesh) in dry condition in a mortar and pestle. No special precautions were taken for proper mixing. The mixtures were then compacted into a cylindrical form having an approximate dimension of 1 cm in diameter and 1 cm in height. For this compaction an ordinary

Jan 1, 1965