Search Documents

By R. M. Caves

High-purity dense tungsten coating is obtained by means of a modified de Boer-van Arkel iodide process using tungsten bromides. The all-glass reaction system is pumped, baked, and sealed (pinched-off) at about 10-7 mm Hg pressure. The bromides then formed in situ are decomposed, depositing tungsten on heated tungsten surfaces. Heating of the specimen is done inductively in a novel arrangement that avoids electrodes of glass-to-metal seals. The tungsten, deposited at specimen temperatures from 2000° to 2800°F and bulb (halide) temperatures of 225" to 725°F, was adherent and uniform, and ranged in thickness to 1/8-in. REFRACTORY metals are of interest at NASA for use in hypersonic aircraft, in rocket engines, and in other thrust devices where very high temperatures are encountered. Tungsten, with a melting point about 6100° F, is potentially very useful for some of these applications. Considerable research on tungsten and its alloys is currently being conducted at the NASA Lewis Research Center. In this tungsten research program, there is need for a method of depositing high-purity, nonporous tungsten coatirlgs. Metallurgical bonding of the coating both to itself and to the substrate is required. In addition, it is necessary to be able to deposit thin, uniform coatings on substrates of a variety of shapes and sizes for laboratory test purposes. A survey of the methods previously used for depositing tungsten coatings indicated that none would likely meet these requirements for high purity, good uniformity, and high density except thermal decomposition of the halides. The method for coating that was selected for investigation was the thermal decomposition of tungsten bromide. This is a variation of the van Arkel and de Boer iodide process established years ago and recently reviewed.1,2 This process is applicable to the transition metals in general. More recently, the application and techniques were extended with chlorine3 and fluorine,4 and included the coating of tungsten. This is believed to be the first report on the use of the bromide for tungsten coating. Bromine was chosen over the other halogens because it promised a lower temperature for tungsten

Jan 1, 1962

By Philip D. Pearson

CALAND Ore Co.'s dredging program has reached the halfway mark. The goal is to remove more than 160 million cu yd of lake bottom material overlying the iron orebody in Falls Bay of Steep Rock Lake, Ont. Two large dredges were constructed to remove this overburden, a layer of soil about 90 pct varved clay some 400 ft thick. Moisture content of the clay is high-approximately at the liquid limit of the soil. A few years ago, searching for additional reserves of ore, Inland Steel Co. looked toward Canada and the newly developed Steep Rock iron range. To this end an option agreement was signed Dec. 30, 1949, between Steep Rock Mines Ltd. and Caland Ore Co. Ltd., a wholly owned subsidiary of Inland Steel. Several drilling programs were conducted between this date and Jan. 1, 1953, when a 99-year lease was signed covering an area of 1249 acres. This lease calls for ore production to begin in 1960, with full production of 3 million tons per year by 1969.

Jan 8, 1957

By N. S. Kenny, A. A. Burr

THE purpose of this note is to present evidence that vacancies, which have been produced by quenching from a high temperature, alter the rate of strain-hardening of an hep single crystal. The majority of investigations of the effects of quenched-in vacancies on the yield stress of metals have been made using fee samples in the form of thin wires. However, there is an inherent disadvantage in using such wires to study the effects of vacancies on the rate of strain-hardening of metals because fee wires begin stage II slip either immediately upon yielding or very shortly thereafter. When stage II slip occurs, very rapid strain hardening also occurs, masking the effects of vacancies on the rate of hardening. In this investigation single crystals of magnesium hep were studied since magnesium has only one slip plane at low temperatures and has, therefore, an extensive easy glide region. In addition, the effect of both static and dynamic recovery on the rate of hardening were eliminated by testing in liquid nitrogen. Both forms of recovery occur in hep metals by dislocation climb, which is a diffusion controlled mechanism and is negligible at liquid nitrogen temperatures. Finally, the dependence of the strain-hardening rate on the crystal orientation was eliminated by using the equations of Schmid and Boas.' Variations in the strain-hardening rate could, therefore, be attributed to the presence of vacancies. Single crystals in the form of rods approximately 5 mm in diam and 6 cm long were grown by a modified Bridgman technique from commercial high-purity magnesium (99.97 pet) supplied by the Dow Chemical

Jan 1, 1962

I had hoped when the time came for me to address this meeting that gold mining would be in a much happier position than we find it to-day.As it is, and because of the demands of national security, we find this great and valuable primary industry relegated to the background and in danger of temporary extinction.These notes refer mainly to gold mining in Western Australia, whence comes the major portion of Australia's production, and their purpose is to record a brief review of the industry immediately prior to the general disorganization that is following the call-up of men from the mines.During this period of reduced production the loss of comparable statistical data will make it impossible to follow the progress of the industry, and, since the period may be long, it occurred to me that information might be derived from an examination of the trend of recent production that would indicate what may be expected of the industry when full production is resumed in the future.Since the revival of gold mining, which started in 1931, most of the old-established mines have reorganized and, in some cases, completely renewed and enlarged their equipment in order to achieve maximum production, and old mines hitherto unpayable have been re-opened and equipped. At the same time large sums have been spent in scientific prospecting and in search for new mines, and it is safe to say that at the end of 1939, when gold production reached its peak, practically every known mine in Western Australia that could be worked profitably was in production.During this period the number of men employed in the industry rose from 5,961 in 1931 to approximately 15,000 in 1939. From the outbreak of war in 1939 to the end of 1941 the output from the mines was maintained at full pressure, maximum tonnage beingrecorded in 1940, although a reduction in the grade of ore treated caused a slight falling off in gold production.During 1941 there was a. fall in both tonnage and grade. The decline in tonnage was due partly to the closing of the Lancefield and Mount Magnet mines, and partly to the shortage of labour brought about by the response of the goldfields to the call for men for the fighting services, the average number of men in the industry in this year being reduced to 12,929.With the entry of the United States into the war in December last and the pooling of the resources of the allied nations, the need for gold as a purchasing medium passed, and with its passing there arose the demand for the transfer of the man-power engaged in gold mining to other fields of industry directly connected with the war effort.There was a ready response by those connected with the industry who...

Jan 1, 1942

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

By M. S. Burton, B. W. Christ, G. V. Smith

Evidence of the effects which high-angle grain boundaries and veining subgrain boundaries have on the yield phenomenon of zone-refined iron is reported. Room-temperature tensile tests on 50-mil wive at several gram sizes produced upon recrystallization at diffevent temperatures below 910C (a-y phase-transfornzatzon temperature) show that upper and lower yield stress decrease with increasing grain size. The upper yield point effectively disappears at grain sizes of 81 and 102 u in samples of this diameter. However, samples of 129 p grain size. produced during recrys-tallization at 950°C, exhibit a pronounced upper yield point and an increased lower yield stress. Possible causes of the reversal in the grain-size dependence of yielding are discussed. Veining substructure, detected with picval-HC1 etchant, but not with 2 pct nital, is formed during the a-y transformation, and is believed to account for the observed effecls. The strengthening associated with high-angle boundaries in zone-refined tron is discussed in terms of: 1) the stress dependence of slzp multiplicity, and 2) the stress dependence of dislocation emission from grain boundaries. WIDE use of transmission electron microscopy and dislocation etch-pitting techniques has led to a growing awareness of the presence of dislocation substructures in annealed pure metals. Whereas much speculation'-4 has developed about the influence which subgrain structures have on the mechanical behavior of metals, particularly the yield strength, only limited experimental evidence correlating subgrain structures with lower yield strength has been presented. 2,3,5-7 It is the purpose of this note to present experimental evidence of the effects which grain boundaries and subgrain boundaries have on both the upper and lower yield strength of zone-refined iron. Effects due to high-angle boundaries formed upon recrystallization below the a-y phase transformation are compared with effects due to veining subgrain boundaries formed upon "recrystallization" above the a-y phase-transformation temperature. These effects are further compared with the reported influence 2,3,5-7 which low-angle boundaries have on the lower yield strength of bcc transition metals. EXPERIMENTAL PROCEDURE The starting material for these experiments was a 1-in.-diam zone-refined ingot prepared at Battelle Memorial Institute. Initial purification of electrolytic iron by vacuum-induction melting was improved by a floating zone-melting treatment in ultrapure hydrogen.' Chemical analysis of this zone-refined iron appears in Table I. Tensile samples of 50-mil wire were prepared by rolling and drawing portions of the ingot. An intermediate recrystallization anneal at 625°C after rolling to a reduction in area of 85 pct was carried out in an evacuated Vycor capsule (10-=5 mm Hg). Further reduction in area of 91 pct was followed by recrystallization in evacuated Vycor capsules at temperatures between 600" and 950°C, see Table 111. All samples

Jan 1, 1967

By S. P. Vanka, B. G. Thomas, S. Sivaramakrishnan

"During the continuous casting of steel, transient 'flow events can be very important to the generation of quality problems, such as shear entrainment, surface level fluctuations and bubble entrainment. These phenomena can be better predicted using Large Eddy Simulation (LES) models than the K-E models, which have been extensively studied. In this work the turbulent transient flow in a water model of a continuous caster has been both simulated using LES models and measured using Particle Image Velocimetry (PIV). The results of PIV and LES have been compared to validate the LES model and also to enhance the understanding of the prominent transient features of the flow field. The flow near the top surface in PIV was found to contain periods of 5-1 Os when the velocities were three to four times their mean values, which is of importance to the shear entrainment of the liquid flux. In both simulation and PIV the upper roll structure is found to change chaotically from a single large recirculation structure to a set of distinct vortices. The inlet swirl in PIV is seen to persist more than halfway across the mold, causing a characteristic staircase velocity vector pattern when viewed in a plane parallel to the wide faces. The lower rolls in PIV are significantly asymmetric for very long periods of time (- I-hour) and go through a repeating sequence of features. One of these features involving a short circuit between the upward and downward flow in the lower roll is also seen in the simulation and is of significance to bubble entrapment.IntroductionThe turbulent flow through the nozzle and in the mold of the continuous caster has been studied extensively using computational Reynolds Averaged Navier Stokes (RANS) models of turbulent flow [1,2]. Defects, such as internal inclusion of liquid fl4x through surface shear, pencil pipe defects due to bubble entrapment, surface defects due to level fluctuations are caused by transient flow phenomena oc'curring in the mold. These phenomena can be better predicted using transient Large Eddy Simulation [3] or ""LES"" models."

Jan 1, 2000

By Atul Kurnar

In the present research a two-cell polymer electrolyte membrane fuel cell stack (PEMFCS) with SS-316 bipolar plates has been tested. Different flow field designs were studied and a modified multi-parallel channel design is proposed. The stack is stable within ±3 mV even after 1000 hours of continuous operation, indicating efficient water management and effective removal of any metal ions from the stack. Also no iron is detected in membrane electrode assembly (MEA) by EDAX analysis after 1000 hours of cell operation. Results indicate that high operating pressures beyond 138 kPa didn't significantly increase the performance of cell, however added much to the pressurization cost of the system. Tests at different temperatures showed that at temperatures below 80°C, external humidification could be completely removed. The prototype stack is also tested under variable load conditions simulating highway-driving schedule. The experimental efficiency of PEMFCS is 48%, which is in good agreement with the model predicted efficiency of 53.8 %. Results show that 59% of the total losses are due to ohmic polarization in the cell. Further analysis on applications of the stack in automotive transportation system is in progress.

Jan 1, 2002

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete; A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general infor-mation as miry be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and n manganese-steel grate bars.

Jan 1, 1937

By Rob Assabgui

Presentation Overview ? Stobie Mine Sublevel Cave Background ? Elevated Silica Levels ? Silica Control ? Challenges and Issues ? Conclusions

Oct 1, 2010

By Jerald E. Harris

"Often taken for granted, drill accuracy plays a major role in the relative success or failure of a blast.Expensive technological advances in equipment capabilities, drilling tools, communications, explosives, and timing can quickly be nullified by poor drilling."

Jan 1, 1999

By Richard Lovat

INTRODUCTION Soft ground tunnels may be above the ground water table or they may be subaqueous. The ground may be clays, silts, sands, gravels, glacial deposits, boulder tills, and any of these in any combination. Because of the relatively low strength and deformability of soils, difficulties often arise in soft ground tunnelling. These soil characteristics and resultant tunnelling difficulties, have had a direct influence on the development of "Lovat" Tunnel Boring Machines. We have been required to recognize and adapt to unusual ground conditions and to follow through with design, fabrication, and field maintenance to ensure dependable, trouble-free operation. The basic "Lovat" machine is a fully shielded, wheel-type with the cuttinghead driven by a monorace type bearing with gear drive incorporated in the bearing. Mechanical innovations have been added to the basic machine which complement the resources of manpower, equipment, and materials available to the contractor for a specific operation. FULL FACE SUPPORT The installation of hydraulically operated closure doors or flood control doors, at the cuttinghead, is one of the early "Lovat" technical innovations. Flood control doors provide full face support in running or flowing ground. In water bearing sands and silts the excavated material can

Jan 1, 1981

By Jacques B. Wertz

Even with the best geological maps, there is a constant need for further information and a constant demand for new clues, particularly in exploration work. New ideas and new thoughts are a necessity for progress. In the structural study of an area, be it in Arizona, Africa, or British Columbia, the basic fracture pattern has to be determined first. There is, however, no assurance that the trends shown on the map are really meaningful because they often are secondary in nature, having occurred as a consequence of an intrusion, of doming, or of gravity faulting. Thus, such trends often are a weak basis for assuming the presence of ancient and important zones of fractures that could constitute useful guides to mineral exploration.

Jan 6, 1969

By Philip Morse

THE Australian lead-smelting plants began to use charges carrying high zinc percentages somewhat earlier than was common with American plants. When lead smelting first started in Australia the immense deposits of oxidized lead at Broken Hill were available but later these oxidized ores became exhausted and were replaced by sulfides. This was before the days of flotation and these sulfides when concentrated carried about 1 per cent. of zinc to 6 per cent. of lead. The works of the Sulphide Corpn. at Cockle Creek was perhaps the pioneer in high-zinc slags but the Port Pirie plant of the Proprietary Co. was a close and very able second and has continued the work to the present time. The Cockle Creek lead furnaces remained in operation until shortly after the war when most of the Broken Hill companies combined and took over the Port Pirie plant to treat their concentrates. As it was the practice both at Cockle Creek and Port Pirie to carry 20 per cent. or more of lead on the charge, it was found that under these conditions of large amounts of zinc in the charge, good roasting was absolutely necessary and matte production was unwise. The Huntington-Heberlein system of roasting was introduced and later the Dwight & Lloyd process. In this way, by roasting the sulfide portions of the charge as thoroughly as possible and making no matte, a method of smelting was developed where the slag over long periods carried as high as 20 per cent. ZnO without serious furnace troubles, and slags carrying even up to 33 per cent. ZnO have been reported. The zinc slags were not very different in appearance from the ordinary slags produced in American practice except that they gave off more smoke and fume on tapping. The slag usually ran hot and freely, coming from the tap in a full stream. Normally there was little crust on the sides' of the furnace and the tuyeres gave no trouble though they were always rather dark.

Jan 1, 1929

By Andreas Nolte

In 1999 HÜTTENWERKE KAYSER AG (HK) in Germany will produce more than 180,000 t/y of electrolytic refined copper. To achieve this production from materials with copper grades from two to seventy percent and diverse copper alloys, HK operates three blast furnaces, one holding furnace two Peirce Smith converters and two anode furnaces. Technical, metallurgical and economic factors for the ongoing process optimization are outlined. The fluctuating quality and quantity of raw materials renders complex this optimization. The principal variables are the quality and quantity of process consumables: coke, copper-iron, limestone, oxygen, as well as the blending of feedstock and a new organization of the operating crews. The search for new metallurgical process parameters is ongoing. HK started with an intensive research programm in November 1997. As a result it will be possible to cut processing costs by about ten per cent, to increase the blast furnace capacity by ten per cent and to lower the metallurgical losses of copper and tin in the slag by more than ten percent. The presentation concludes with information on future steps to continue the optimization process.

Jan 1, 1999

By Alan C. Richter

Introduction The East-West Gateway Coordinating Council is an organization of local governments formed in 1965 to identify regional problems and to formulate policies, plans and programs to resolve them. The major goal of the Gateway Council is to improve the quality of life for the citizens of the St. Louis Region. While East-West Gateway Coordinating Council is the organization I represent and it only deals with the St. Louis Metropolitan Area, you will find one or more similar organizations in each of our nation's urbanized areas. As a result, for illustrative purposes, I will use my organization to portray what is happening nationwide. For example, in order to eliminate duplication, the Council reviews local applications for approximately 100 federally funded programs in such areas as highways, mass transit, parks, water treatment, and sewers before they can be sent to the appropriate funding agency. The Council's varied functions place it in a unique position of receiving more and more responsibility for developing strategies of implementation of various environmental regulations. This is due to the fact that environmental control is a relatively new field and we, as a country, are relatively inexperienced. The resulting regulations and guidelines will depend, to a great extent, on what the general public is willing to accept in terms of controls and what price they are willing to pay in terms of taxes and increased costs. Land Use: Growth vs No Growth This is perhaps the most encompassing environmental issue. We, as a nation, are beginning to realize that land is a limited natural resource and that the way we choose to use 'this resource affects many other aspects of our lives--whether we can catch edible fish in the Mississippi, how much we pay for sewer services, if we can swim in a

Jan 1, 1977

By Shazad Hosein, Bill Birch, Catherine Johnson, Toby White, Liam Bermingham

Air overpressure (AOP) from blasting can give rise to a significant number of blasting complaints from residents living adjacent to blasting operations from mines, quarries or civil engineering projects. High amplitudes of AOP are usually associated with the lateral movement of a vertical free face, but it can also be caused by the upward lifting and the venting of gases through the surface of the blast area.

Jan 1, 2018

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997

Roof screening for ground control originated with metal miners in the western United States. At first chain-link fence was used, but because it was so difficult to handle, the miners started installing a more rigid welded wire screen used in the concrete industry. Eventually coal mines in the west began to use screen, and now more and more coal operations, especially longwall mines, are installing roof screen on a regular basis. Screen use has recently increased in the Illinois basin and is now making its way to underground coal mines in the eastern U.S.