Search Documents

By R. S. Cartwright

TWO types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent on the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination—the combination which when engaged will suspend the least amount of weight—has a value of 1.00. According to the table there are "blind spots" in the series. This is true particularly among the lowest ratios, which are most used to suspend the major part of the weight when great depths are reached. It will be noted that there is a difference of nearly three units in the value of the

Jan 1, 1929

By J. F. Radavich

Many heats of steel of low carbon value have been known to produce brittle pieces of steel. The brittleness is believed to be due to the impurities located within the grain boundaries. Such brittle steels have been examined with an optical microscope to ascertain the nature and the amount of the impurities present at the grain boundaries. Due to the relatively low resolving power of the optical microscope, the impurities are not visible in fine detail. The writer obtained some sheet steel and proceeded to determine the location of the impurities and to show the application of the electron microscope to the study of grain boundaries. One sample was known to be capable of becoming embrittled, whereas another sample was believed to be much less susceptible to embrittlement. Treatment of Specimens The specimens were embrittled by annealing above the A3 point under mildly oxidizing conditions. One piece of ingot iron could not withstand a 90" bend, whereas another piece of ingot iron was not affected and could withstand a 90" bend. The brittle piece was then annealed at a high temperature in a hydrogen atmosphere. The annealed ingot iron was termed cured and could withstand a 90" bend very easily. The three specimens examined will be designated as brittle, good. and cured in the discussion that follows. Procedure The sizes of the specimens were as follows: one piece of brittle ingot iron-3/8 by 35 in.; one piece of good ingot iron-96 by 1/8 in.; one piece of cured ingot iron-36 by 54 in. The specimens were too small to be polished by hand and therefore were mounted in bakelite. The polishing procedure was carried out in the conventional manner with the use of 1/0 through 3/0 papers, and the final polish was done with alumina on a billiard cloth. The specimens were then etched in a 4 pct solution of picral in alcohol, and then they were examined through an optical microscope. An area was chosen that showed distinct grain boundaries, and an effort was made to keep near this area when pulling the replicas REPLICA TECHNIQIJE The replica technique used in the preparation of the replicas for examination under the electron microscope is described in Electron Metallography.' It consists essentially of the following steps: 1. Obtaining a suitably etched specimen. 2. Applying a swab of ethylene di-chloride on the surface. 3. Applying a formvar solution on the surface. 4. Placing a screen on any desired spot. 5. Breathing on the fornivar layer. 6. Applying scotch tape on the screen and film. 7. Pulling the film and the screen up with the Scotch tape. 8. Separating the screen from the Scotch tape. This replica technique is very similar to the one described by Harker and Shaefer. However, with the added step, the percentage of replicas removed is very much higher regardless of the length of the time from the etching of the specimen to the actual pulling of the replica. The replicas were then shadow cast with manganese at a filament height to replica distance ratio of 1 1/2:7. This produced a very high contrast replica for use in the electron microscope. One of the dificulties encountered with this study was the restricted area of the specimen. The width of the specimens was the same as that of the 200 mesh nickel supporting screen. In order to increase the effective area, the screens were cut down as shown in Fig 1. The arrow indicates the direction in which the replica was pulled. This operation made it possible to obtain a large percentage of good replicas. Fig 3 shows an electron micrograph of a brittle piece of ingot iron and a grain boundary that was polished mechanically. The surface is very rough probably due to the incomplete removal of the flowed layer by the picral etchant. The grain boundary does show evidence of impurities. It was decided to electropolish the specimens to obtain a much smoother surface than the one obtained by mechanical polishing. ELECTROPOLISHING The specimens were cut in half to expose the metal on the back side. The exposed metal had sufficient area to make good electrical contact and electropolishing was carried out easily. The conditions for electropolishing were 0.9 amp, 35 volts, and 25 sec. in an electrolyte composed of 850 cc of ethyl alcohol, 100 cc distilled water, and 50 cc of perchloric acid. The polished specimens were then etched in the 4 pct picral solution for a shorter time than was necessary for

Jan 1, 1950

By H. Petersen

If a coal mine producing two hundred thousand (200,000) tons of coal per year could effect a 2 per cent decrease in the percentage of slack there would be an additional 4,000 tons of prepared coal produced. Most operators will say that these prepared sizes of coal are worth about $3.00 more per ton to them than the slack or in other words an additional $12,000.00 pier year profit could be made by a decrease of 2 per cent in slack. A large tipple with all the finest modern equipment of shaker screens, conveyors, box car loaders, etc., can only produce a grade of coal dependent upon the coal delivered by the mine car at the top of the tipple. In the mine, coal-cutting machines have been doing their part for many years toward decreasing the percentage of slack. There is therefore, only one phase of production left where real effective work can be done, that is, intelligent and constant supervision of preparatory work and shooting. The quality of coal is really entirely dependent upon the kind of coal produced at the face in the mine. Our problem is therefore, at that place. The writer is thoroughly convinced that with the proper placing of holes the use of correct amount of a suitable explosive, thoroughly tamped, with the bug dust entirely removed from the mining, a decrease in slack can be effected. We will take up this problem under five headings. First-The proper placing of bore holes. Second-The proper amount of permissible powder. Third-The proper loading and stemming of the shot.-Cushing shooting. Fourth-The necessity of removing the bug dust from the mining. Fifth - The - standardization of rounds. First-The Proper Placing of Bore Holes. The most important thing and the real secret of successful blasting of coal is the proper placing of the bore hole. This results in the correct balancing of the shot and the securing of the maximum efficiency of the explo¬sive. If you are operating a mine with a 6-foot coal seam, you most likely are using a 6-foot cutter bar on the coal cutting machines. You should use three holes to properly bring down the coal. (1) A center shot in the middle of the room drilled flat, or rather parallel to the mining-the heights of this hole will depend upon the top parting. If the coal is frozen to the roof, it will be necessary to have the hole as close to the roof as possible. If there is a free parting, the hole may be placed lower but not over twelve inches from the roof. (2)

Jan 1, 1925

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration. Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet.Processing the are as received resulted in 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J.IntroductionA five-year mineral development sub-agreement was signed between the federal government and the province of Manitoba in 1984. The purpose of the agreement was to establish a work program which would strengthen and diversify the mineral resource industry of Manitoba. Basically, the agreement covers three sectors: Sector A, geoscience; Sector B, mining and minerals technology research; and Sector C, development studies.Project selection involved input from industry, federal and provincial representatives. In the case of industrial mineral s, the selection was initiated at a meeting held at the offices of the Department of Mines and Energy, Winnipeg, Manitoba, in October 1985. One such project was the evaluation of the chromite ore deposits at Bird River, Manitoba."

Jan 1, 1988

Various methods and software have been trialled for simulation of Au grades at Boddington Mine. This covers in-house and public software as well as sequential and turning bands methods. The diversity of options was further expanded with comparison of point and direct block simulation. Some difficulties were encountered in incorporating high-grade restrictions. Altering parameters or software can make very significant differences and give results varying from estimations. This paper details a new simulation run with validation and tests for local calibration (or progressive correction) of the simulations to the estimations, focusing on reproduction of statistics. This approach brings to the forefront the question æwhat is the purpose of the simulations?Æ Results and some ideas for future applications at Boddington are summarised.

Sep 26, 2011

By Franz R. Dykstra, R. F. Tatnall

A ferroalloy is defined as: "An alloy of iron with some element other than carbon used as a vehicle for introducing such an element into the manufacture of steel. The element may alloy with the steel by solution or, as the carbide, -neutralize the harmful impurities, by combining with them and separating from the steel as flux or slag before solidification."a The most commonly used ferroalloys are: ferromanganese, ferrochrome, ferrosilicon, ferrovanadium, ferromolybdenum, ferronickel, ferrotungsten, ferrocolumbium, and ferrophosphorus. Concern here is with the sources and markets of the major metallic alloying elements. The discussion is further restricted to those - ferroalloy ores, the principal use of which is in the production of steel. Phosphorus, silicon, and tungsten, for example, are ferroalloys of some economic significance, but other uses dwarf their alloying applications. Thus, this discussion will deal with the ores of managanese, chromium, nickel, molybdenum, vanadium, and columbium. As shown in Table 14.1B.1 ferroalloys serve to- facilitate processing and impart to the finished steel such characteristics as tensile strength, ductility, low-temperature impact, hardenability, high-temperature strength, corrosion resistance, toughness, and abrasion resistance. In the steel-making process, ferroalloys may be added in the charge, in the molten bath near the end of the finishing period, in the ladle, or in the molds. Timing of the addition depends on the effect of the addition on the temperature of the molten metal, the formation and elimination of reaction products, and the protection of subsequent additions from oxidation. MANGANESE General Approximately 95% of the manganese ore sold is consumed by the steel industry, either as ferromanganese or as manganese metal. Manganese is the universal alloy, without which good steel cannot be made. It serves as a scavenger, removing phosphorus, sulfur and, to a degree, oxygen from the melt. As an alloying material it makes steel hard, tough, and resistant to wear. Approximately 6 kg of manganese is required for every ton of common steel produced by United States steelmaking practice. The remaining 5 % of the manganese ore consumed consists of special or so-called "chemical" ores, including high-grade pyrolusite ores, electrochemically reactive "battery ores," and a number of special varieties, as well as those otherwise regarded as "metallurgical ores."

Jan 1, 1976

By H. R. Deeth

NEPHELINE syenite is a sodium, potassium, aluminum silicate rock occurring in many countries. Large deposits have been investigated in Russia, India, and Norway and in the U. S., where it is known to occur in Arkansas, New Jersey, and Wisconsin. There are extensive areas containing nepheline syenite in south-central Ontario, a region surveyed in 1905 by Adams and Barlow. By 1925 considerable interest had developed in searching for aluminous raw materials that could be used by the glass industry. This finally focused attention on the nepheline syenite described by Adams and Barlow in 1910.1

Jan 11, 1957

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By Melvin E. Poad

This Bureau of Mines report presents two phases of a research program to evaluate a single-entry system for longwall development. Organizations participating in the program; which began in July 1971, include the Bureau of Mines, the Mining Enforcement and Safety Administration, and the University of Utah, working under a cooperative agreement with Kaiser Steel Corp. at its Sunnyside mine in Utah. Part 1 of this report describes the present longwall mining practice, including a brief history, and discusses the advantages and disadvantages of a single-entry development system and its introduction in the United States. Part 2 of the report presents the research program; test design, instrumentation for ground and support evaluation, and the test results from the No. 2 mine. Subsequent reports will describe the research conducted in the No. 1 mine.

Jan 1, 1977

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The performance of the improved microclimate suit by N. B. STRYDOM M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, B.Sc. (Potch.) (Visitor), and W. H. VAN DERWALT, M.Sc. (Potch.) (Visitor) An assessment has been made of a new improved microclimate jacket when worn by men working for four hours in a hot environment (wet-bulb temperature of 33,9°C and an air speed of 0,4 m/s) and at work rates of 35 Wand 70W. At the lower rate of work in heat, the use of microclimate suits maintained the rectal temperatures of the men at almost the same level as when they worked without that protection at normal room temperature (20°C). At the greater rate of work without protection, the men's rectal temperatures rose to 40°C within two to three hours, so that they could not complete four hours of work. When they wore microclimate suits, they easily completed four hours of work, and their rectal temperatures were lower than when they worked at the lower rate without protection.

Jan 8, 1975

Application of Agitated Leaching for Iron Removal from Silica Using Sulfuric and Hydrochloric Acid In this research, iron removal from silica used in glass industry was investigated using agitated leaching method. Silica sample was provided from silica concentrate originating from Chalchoog Silica Mine located in Abhar, Iran. The sample contained silica, iron oxides and clay minerals. For characterization of samples XRD and XRF analysis and atomic absorption method were applied. Silica and iron oxide (Fe2O3) grade of head sample was 98.41 per cent and 0.067 per cent respectively. Two inorganic acids (sulfuric and hydrochloric acid) were used in agitated leaching tests. Two series of L9 orthogonal array of Taguchi design with replication were used to determine the effect of parameters including acid dosage, leaching duration, ambient temperature and solid content on iron removal. The statistical calculations and analysis of variance (ANOVA) were carried out by means of DX7.0, Minitab14.0 and Winrobust1.02 softwares and also statistical calculations were checked manually using Excel software. Also multivariate regression was applied in order to forecast Fe2O3 conent of final product. The optimum conditions for leaching tests which sulfuric acid was employed are as follows: 40 minutes leaching time, temperature of 85¦C, 40 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.042 per cent. The optimum conditions for leaching tests which hydrochloric acid was employed are as follows: 80 minutes leaching time, temperature of 75¦C, 30 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.035 per cent.

Sep 13, 2010

By Peter J. Lean

The introduction oE computer control in the grinding circuit of the New Broken Hill Consolidated Limited concentrator in the early 1970's gave smoother operation at optimum performance. The ore feedrate and water additions to the grinding circuit were controlled to operate each of the ball mill/ rake classifier grinding units at the upper limit of the circulating load while classifier overflow density was maintained to give a product size and pulp density suitable for flotation. An incremental expansion of the concentrator in 1981-82 included the installation of hydrocyclones in closed circuit with three of the four ball mills. Without the rake classifiers in circuit the previous control strategy could not be used and the complex interaction of hydrocyclone performance characteristics when classifying coarse grained sulphide ore resulted in the over-grinding of the lead mineral galena. Testwork aimed at optimising grinding circuit performance recognised the enhanced tendency of higher specific gravity minerals to report to the cyclone underflow. The data has been evaluated on an individual mineral basis and then used to develop a model For grinding circuit control. The development of the model which uses inputs of ore feedrate, metal content of the Feed and slurry density of the cyclone overflow to predict the size of the minerals in the grinding circuit product is described and model predictions are compared with plant performance.

Jan 1, 1984

By Fred N. Kissell

Work done by Foster-Miller Associates under a Bureau of Mines research contract has developed methods to increase significantly the amount of fresh air that reaches the front of a continuous-mining machine. The emphasis was on removing methane build- ups that occur at the cutterhead. Using a full-scale plywood mockup of a coal mine working face area, the study showed that in many instances only about 20 pct of the fresh air heading towards an exhaust brattice or tubing actually gets to within 1 ft (0.3m) of the face. The key to providing more air at the face is to enhance and move forward the natural airflow pattern. This change in the natural airflow pattern can be accomplished by taking advantage of the air-moving abilities of the conventional water spray. It was discovered that if all the water sprays on the machine were realigned, then ventilation efficiencies of 70 pct or more were achieved regularly. This meant that if 9,000 cfm (4.2 m3/s) was entering the brattice, at least 6,300 cfm (3.0 m3/s) of this was reaching to within 1 ft (0.3m) of the face. This water spray realignment consists of placing a few nozzles on the side of the machine opposite the curtain and also tilting the front sprays slightly towards the curtain side. Recently, two underground tests and two additional independent laboratory tests of the water "Spray Fan" have been completed. In general, they have confirmed the performance of the Spray Fan system, but they also have provided useful information as to its difficulties and limitations.

Jan 1, 1980

By Adam Gesing, Ron Dalton, Richard Wolanski, Larry Berry, Christopher Stewart

As the quantity of aluminum recovered from shredder scrap continues to increase, together with increased content of aluminum in automobiles, so does the economic incentive to further upgrade shredder scrap. This upgrade will be done by sorting and recovering the aluminum by specific usable alloy compositions. The metal recycling industry infrastructure needed to deal with the increased aluminum scrap supply already exists. It is an inverted pyramid structure that in North America comprises: 3000 scrap collection yards, 200 shredders, a dozen sink-float plants and one heavy metal sorting operation. The technology for upgrading aluminum sorted from shredder scrap is already either in industrial use or in the final stages of pilot plant development. However, the current automotive aluminum recycling infrastructure will need to adjust to deal with higher volumes of the metal from aluminum-intensive vehicles that will be appearing in shredder scrap -20 years from now.

Jan 1, 2000

By Joseph A. Holmes, Henry Kreisinger

At the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a con~mittee consisti~lg of 11. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr..J. K. Clement, physicist. The problem, essentially one of physical chemistry, is estremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of' the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. in volatile matter and from 40 to 75 per cent. of fixed combtistible. The greater part of the latter is burned on the grate: but the volatile combustible leaves the freshly-charsed coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible mill leave the furnace only partly burnecl, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven oft' per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 30 cu. ft., the burning mixture will stay in it,

Jan 1, 1911

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By Carl Thieme

INDUSTRIAL specialization has rapidly created a demand for new and better alloys. A more thorough understanding of the requirements of specific industries and the discovery of processes by which it has been made possible to utilize certain metallic elements in larger quantities, together with greater purity in most virgin metals, has resulted in a great increase in the number and variety of alloys. This increase in the number of elements entering into non-ferrous alloy manufacture has increased the contamination in secondary metals, as received by the smelter. In order to successfully refine scrap of a much more complex nature it has been necessary for the smelter to install new equipment and to constantly search for new methods of refining as well as to improve the methods already in use. In some instances it is largely responsible for specialization in the secondary metal industry. It is usually necessary to remove the contaminating impurities in scrap or eliminate to a degree not objectionable, no matter how introduced. In order to know what metals or elements are of an objectionable nature, the smelter must make a study of the effect of single elements and combinations of elements on many of the physical and mechanical properties, such as strength, ductility, color, hardness, casting soundness, etc. The smelter of secondary metals must be able to utilize scrap materials of all kinds, for, sooner or later, most fabricated metal parts and the waste products formed during the process of manufacture find their way to the smelter. In addition, the smelter, in contracting for salvaged material from the producer, gets some undesirable and unusual materials. The value of secondary metals and the importance of their recovery has increased in recent years and it is no longer sufficient to recover the base metal only, such as copper from copper-bearing material, but it inessential that other elements present be recovered and converted into useful form.

Jan 1, 1928