Search Documents

By Yuexin Han

The characteristics of comminuted hematite products using a high pressure grinding roller (HPGR) and conventional jaw crusher (JC) were comparatively studied by screening, optical microscope, scanning electron microscope (SEM) and Brunauer, Emmett and Teller (BET) techniques. Major properties investigated included product size distribution, particle cracks, specific surface areas and pore volumes. Results showed that in a closed-circuit operation with a screen opening of 3.2 mm, the HPGR and JC gave a similar P80, but the HPGR achieved a more uniform size distribution, more fines and a higher crushing efficiency. Three modes of cracks were identified, namely transgranular cracks, innergranular microcracks and intergranular microcracks. Transgranular cracks originated from shearing breakage. Innergranular and intergranular microcracks were generated by HPGR via the two main nonrandom breakage forms, preferential breakage and interfacial breakage, depending on their respective ability to endure stresses when mineral phases (particles) were loaded against each other. The BET values for the same-size fractions showed that HPGR products gave higher specific surface areas and more pore volumes than JC products. This indicates that HPGR-crushed products are easier to grind because of their high porosity and extra cracks.

May 1, 2012

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By J. Abdollahisharif

Optimal cut-off grade is one of the most critical parameters in open-pit mine design because it defines the ore and waste and thus determines the maximum net present value possible from the mining operation. Although the algorithm presented by Lane (Choosing the optimum cut-off grade. Colorado school of Mines Quarterly, vol. 59, no. 4, 1964. pp. 811-829) is the most common one in the literature, it does assume constant capacities of the mine, processing, and refinery. In this paper, Lane's original algorithm has been modified to consider variable processing capacities in order to determine the optimal cut-off grade in open-pit mines. The new algorithm proposed here is compared to both Lane's original algorithm and to a previous modification that incorporated rehabilitation costs into the cut-off grade estimation. The algorithm proposed here that permits variable processing capacities is shown to be superior for the determination of optimal cut-off grade to both these previous versions. In addition, a computer-based program was developed in Microsoft Office Excel© to calculate the optimal cut-off grade as proposed here.

Jan 1, 2012

By George Piscsalko

"Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.IntroductionDrilled shafts and Augered Cast-in-Place (ACIP) piles have been increasingly used over the past several years due to several reasons including the reduced noise and vibration, speed of installation for ACIP piles, and the large axial and lateral capacities which are attainable for very large drilled shafts. ACIP piles are drilled and cast without any visual inspection. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2017

To develop an in-mine water treatment system in which bacterial sulfate reduction and limestone dissolution continuously remove metals and acidity from contaminated drainage. Approach A section of mine tunnel was converted into a water treatment bioreactor by constructing cinder block dams and fang the area between them with a porous substrate mixture of limestone gravel and compost. Readily fermentable materials such as dairy whey, spent brewing yeast, or sugar were periodically added to the reactor. Mine drainage was impounded behind one of the dams and continuously percolates through the reactor substrate at a controlled rate. How It Works The reactor substrate soon becomes anaerobic after it is saturated with mine water. Under anaerobic conditions, sulfate-reducing bacteria consume the organic materials that are added to the reactor and generate hydrogen sulfide (HIS) and alkalinity. The H2S reacts with dissolved iron and heavy metals to form metal sulfide precipitates. The alkalinity raises the pH of the water and induces aluminum to hydrolyze and precipitate as aluminum hydroxide [Al(OH)3]. Additional alkalinity is generated by the continuous dissolution of the substrate limestone. Metal sulfide precipitates and Al(OH)3 are retained within the reactor, and the treated water is discharged. The underground location of the system allows year round operation.

Jan 1, 1994

By C. H. Schack

Although viscosity is known to be important in processing and handling finely ground urea, its effect has never been fully quantified. This report describes the methods used and the results obtained in the initial phases of a broad investigation of the influence of viscosity of water suspensions of minerals in flotation, thickening, filtering, and other mineral-dressing unit operations. Several types of vis-cosimeters were tested before reliable and reproducible results could be obtained on mineral suspensions. After the viscosimeter used in the research was calibrated and standardized, tests were made on six pure minerals to study the relationship of pulp density, particle size, crystallinity, and cleavage on viscosity. An orifice-type viscosimeter equipped with a mechanical stirrer gave as good results as other types and was more flexible, faster, and simpler to operate. The orifice-type viscosimeter, when calibrated and standardized with glycerin and water mixtures, proved satisfactory over a wide range of viscosities. The accuracy and reproducibility were reasonably constant between 1 centipoise and 200 centipoises, the anticipated range in common mineral-dressing unit operations.

Jan 1, 1957

By W. H. Adams

Inasmuch as] the mining of phosphate rock and its transportation has so general a bearing on the great industries of this continent, entering as well into the problem of our trade with foreign countries, it may be useful to place on record the following list of localities from which certain products of a like nature are received by us in a business way, or in which we are interested more or less either by ownership or by competition. As a ready means of comparison, the percentages of the mine products and the deteriorating constituents are given : Coprolite (Cambridge).—This material is obtained from the Upper Greensand formation in Cambridgeshire. The phosphate runs from 50 to 60 per cent., and averages 64 per cent. It contains much carbonate of calcium, but little iron, in the ferric condition. The superphosphates manufactured from the material are permanent and little liable to a revert." They contain from 28 to 35 per cent. of soluble phosphate. Coprolite (Buckingham).—From the same formation as the Cambridge variety, and very similar in composition.. It averages 60 per cent. phosphate. Coprolite (Suffolk).—These coprolites are not so valuable for the manufacture of superphosphate as the two previous varieties, as the iron they contain is in the ferric state, and liable to "revert" the soluble phosphate. The phosphate varies from 48 to 60 per cent., but averages 54 per cent. They are of Tertiary formation. Coprolite (Potton or Bedford).—The average amount of phosphate in these coprolites is about 50 per cent. In some cases they may, however, run up to 60 per cent., and in others may not exceed 45 per cent. They belong to the Lower Greensand formation. The ferric iron frequently is as high as 4 per cent., and the alumina as much. Russian phosphate comes from the chalk, and occurs in carious rounded masses. It contains from 28 to 35 per cent. of phosphate, but may run up to 69 or 70 per cent. Curacoa phosphate is also of very high class quality, giving 80

Jan 1, 1890

By Wolfram Groh

New underground floors comprising the complete footprint area of the building structure, were constructed under an existing building in sand, located in the Verdun district of Beirut / Lebanon. The works for the rehabilitation and extension of the Verdun 528 building were carried out between December 1999 and August 2000. A restriction of differential vertical movement of existing load bearing walls and columns had to be respected throughout the construction phase of the new basements. Support measures for the building were taken based on a underpinning system with Bauer SVV preloaded micropiles. The specialty of this underpinning job was that the building loads at the time of preloading and excavation of new basements was substantially less than at final stage. The design of the preloading system was particularly challenging in view of the transition from temporary to final load transfer under variable load conditions. Load transfer was based on the Bauer SVV micropile head system applied in several technical variants. Monitoring of levels of structural elements performed throughout the construction works confirmed that the differential movements of adjacent load bearing columns and walls were maintained within the specified limits.

Jan 1, 2002

By V. Srivastava, T. Ghosh

"Modeling and Simulation of SAG Mill has been widely used in design and optimization of mill performance in terms of its power draw, processing capacity and product size distribution. However, these models are solved under steady approximation and do not provide any information on mill charge distribution in real time. This paper attempts to characterize mill contents by solving Whiten’s first order contents based model in Matlab/Simulink environment. The parameters in the model such as breakage rate (S), discharge rate (D) and appearance function (A) were estimated utilizing process and design data collected from a gold mine operating in Alaska coupled with nonlinear parameter estimation scheme. This model is then utilized to predict dynamic response of other key operational variables such as mill power, bearing pressure, charge level and product size distribution. The transient response of mill behavior with respect to changes in feed size distribution, tonnage and mill feed water is also presented. This dynamic simulation approach can be used for practicing different control strategy and training purposes. The observed response of mentioned variables was validated utilizing dynamic response data from the plant to encompass operational characteristics of SAG Mill behavior. Keywords: SAG Mill, Dynamic Modeling, Simulation, Nonlinear Parameter Estimation. INTRODUCTION Grinding in mineral industry is one the most important steps in the process of size reduction and plays a crucial role in determining the overall economics of the milling plant. Much of the efforts focused on improving the process efficiency using modeling and simulation have been practiced by researcher and engineers. However, up till now these models were simulated under steady state approximation because of their complex nature and difficulty in programming them in a dynamic framework. Steady state simulations have been successfully utilized in circuit designing, capacity planning and pre-flowsheet optimization. The maturity in steady state models is because of its applicability and regular use in steady state simulation packages such as JKSimMet, Limn, ModSim, etc. With the advent of equipment such as SAG and AG mill has been a recent shift in the simulating these models using dynamic approach. Because of the economic benefits of these devices and ability to act both as a primary grinding device and as secondary or tertiary crushing device they have gained a large popularity and are now universal to any milling plant. However, these device poses a real challenge to engineers and researchers in terms of operation and control. The major reason attributed to problems faced is because the ore constitutes the major portion of the charge in these devices when compared to ball and rod mill. This rock charge is subjected to disturbance such as changes in feed size distribution and ore hardness which results in unstable operation and frequent mill stoppages. One way to prevent this is to measure and control these external variables, however, lack of available instrumentation and unavailability of sensors to measure these variables has foiled the understanding of complete process occurring inside the mill thereby, inhibiting development of proper control system."

Jan 1, 2017

By Luiz Felipe Mendonça de Amorim, Adimir Fernando Rezende, Gustavo Sampaio Lopes, Claudio Cesar Gajardo Arraño, Eltton de Sousa Veras, Manuel Villalobos Calderon

Many technical challenges were encountered while conducting near-field construction blasting between the critical intersection of Interstate 10 and multiple active railroad tracks in El Paso, Texas, for the Loop 375 Border West Expressway Project. Blasting was utilized for the removal of an andesite bedrock ridge in preparation for the construction of a new elevated super structure to be suspended over the existing railroad tracks. There was concern that the excessive vibrations and/or permanent rock deformation produced from the blasting within near proximity (20 feet, or 6.09 meters) of the railroad tracks would induce excessive stress and foul the tracks by shifting the alignment. This could result in a major loss of scheduling control between the two major railroad companies that operate in this area. There was also concern that the blasting may cause rock fragments to land on and interfere with critical interstate transportation. Blasts

Jan 1, 2019

By José Carlos A. Cintra

This paper addresses a new experimental procedure to measure the shaft friction and the base resistance of bored piles during static load tests. It is proposed that a set of polystyrene foam discs, placed between the shaft and the base of the pile, be used instead of the usual instrumentation. Throughout the initial stages of the loading test, the foam discs will allow only the mobilization of the shaft friction. The load x settlement curve clearly shows that the shaft friction vanishes at low settlement values. As the load test proceeds, the base resistance is also mobilized. This procedure was used in two belled piles bored at the Experimental Foundation Field of the University of São Paulo, at São Carlos, Brazil. Both piles were 8 m long and had a shaft diameter of 0.6 m. The enlarged base had a diameter of 1.5 m and a height of 0.9 m. Twenty foam discs with a thickness of 20 mm each were placed between the enlarged base and the shaft of the pile. The load tests indicated ultimate shaft frictions of 28 and 30 kPa for measured settlements of 8.98 and 7.39 mm. Base resistance values at failure were 617 and 499 kPa, for a chosen settlement of 10% of the pile base diameter. The proposed approach seems to be straightforward, efficient and inexpensive.

Jan 1, 2002

By Dale S. Preece, Stephen H. Chung

"A discrete element computer program named DMC_BLAST (Distinct Motion Code) has been underdevelopment since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC_BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993b)."

Jan 1, 1999

By H. M. Howe, W. E. C. Eustis

The processes which form the subject of this paper have been experimented on in the laboratory of W. E. C. Eustis, but have not passed beyond the experimental stage. The first is the invention of Mr. J. L. Thomson, of Capelton, Quebec, Canada, the others have been invented by the writers. Thomson's PRocess foR the Extraction oF Nickel. This consists essentially in first rendering the nickel magnetic, and then separating it from the materials with which it is mechanically vol. X.—20

Jan 1, 1882

By Donald C. Moore

INTRODUCTION Published laboratory procedures used by the major crusher manufacturers for estimating crusher size are based upon techniques developed in the mid 1940's. Specifically, the two largest U.S. crusher manufacturers are using the Bond impact procedure. Although the procedure is still in use, there is little confidence in the results. Unless the laboratory results fall within a preconceived range, personal experience is used for selecting the number of crushers and connected horsepower (Coleman, 1978). There have been numerous theoretical studies of the communition of particles. However, no procedure has been widely acclaimed for predicting crusher power requirements. Experimental studies have included breakage by slow compression, slow speed impact and high speed impact. Theoretical results have increased our knowledge of the comminution process, but the procedures have not been capable of analyzing the complex mechanism of industrial crushing machines. The purpose of this chapter is to review the empirical crushing procedures that have been used, including advantages and disadvantages. A new procedure which has been in development at Allis-Chalmers Corp. from 1977 to 1982 is detailed. Actual results of the new procedure on a concentrator feasibility study are included. EXPERIMENTAL GOALS The goals of a laboratory crushability procedure are accurate predictions of: (1) Rock crushability, measured as energy per unit mass. (2) Crusher product size analysis. A procedure capable of predicting these parameters should be inexpensive and require a minimum amount of sample. CRUSHABILITY TESTS Bond Impact Procedure F. C. Bond (1946) detailed the development of the pendulum impact device that is still used by the leading crusher manufacturers (Bond; Rexnord, 1976). The device (Fig. 1) is comprised of two bicycle wheels with 13.6 kg steel hammers tangentially attached to the rims. The hammer faces are 50 mm apart at rest. On opposite ends of the hammers lifting

Jan 1, 1982

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946

By Z. F. Oszter, D. Vincent, W. K. Behrands

With the expansion of open pit operations, belt conveyors are going to be used in the 13 608 to 18 144 t/h (15,000 to 20,000 stph) capacity range, which calls for a review of some of the horsepower calculation methods. This paper presents methods (based on German research data, field tests and theoretical considerations) for the evaluation of the Ky factor in the CEMA formula for belt conveyors of large carrying capacity, which fall beyond the limits of the data given in tables in the CEMA book. (The CEMA limits are 407 N\\m (300 lb ft) and Tave = 7.3 Mg (16,000 lb). At these large loads, the impression resistance of the belting on the idlers plays a major role, which in turn influences the magnitude of the drive horse power required. An example will illustrate the order of magnitude difference of the horsepower values obtained by using a conventional calculation method and the suggested method, as well as the beneficcia1 influence of the 4-roll idler in comparison to the standard 3-roll unit for a large caving capacity belt conveyor. This paper concerns itself with the analysis of the resistance to motion of belt conveyors, emphasizing the evaluation of the frictional resistance to motion due to load and belt pressure on the idlers and the flexing resistance of the belt and material when passing over the idlers. In the case of long and heavily loaded belt conveyors, the aforementioned resistances reach extremely high values calling for close analysis of the phenomena, presently not calculable with normally used formulas. This paper establishes correlation between experimental and empirical data presenting practical formulas a tool for the designer of high-capacity belt conveyors. The application of the formula is illustrated in an example in the Appendix.

Jan 1, 1981

By Valois R. Shea-Albin

Increasing pressure from State and Federal agencies to mitigate mining-induced subsidence damage to overlying structures has presented a unique problem to the coal industry in the western United States. Because sandstone escarpments are an environmental issue, millions of tons of coal reserves that underlie these escarpments risk being classified as unminable by regulatory agencies. At this time, the effect of subsidence on escarpments has not been well documented or characterized. The Bureau of Mines is using numerical modeling techniques to analyze escarpment response to longwall mining. Two- and three-dimensional finite element models have been constructed for a study area near Price, Utah, where longwall panels were mined near an escarpment. This status report includes preliminary results showing that the pattern of subsidence surrounding the escarpment can be simulated through numerical modeling. Models that include such structural details as joint and fracture patterns will better simulate subsidence patterns .and magnitude. By locating longwall panels strategically in relation to the escarpment, stability may be preserved throughout the mining process. Numerical modeling provides a method to analyze relatively quickly the effects of longwall panel location and resulting subsidence on escarpment stability. The goal is to provide a relatively accurate predictive tool for mine planning to determine if escarpment stability can be maintained while maximizing extraction of the coal reserves.

Jan 1, 1986

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By F. Habashi

Lead is an ancient metal. The alchemists related it to the planet Saturn. It was largely obtained by smelting galena which generally contains small quantities of silver. That is why the metallurgy of lead was closely related to that of silver and in some cases the ore was treated only for its silver content. It was also known during the Roman time that lead vapors were toxic. Lead has been produced exclusively by pryrometallurgical methods. Lead refining is a complex process because of the presence of deleterious impurities such as arsenic, antimony, and bismuth. In the nineteenth century lead played an important role as a material of construction in the manufacture of sulfuric acid. In the twentieth century tetraethyl lead was used exclusively as an anti-knock reagent. In recent years lead is mainly used for making batteries.

Jan 1, 2008

By R. L. Grayson, S. S. Peng

"Research has been conducted during the past year on a study to correlate respirable coal mine dust characteristics with worker positions and coal seams. The first characteristic of respirable coal mine dust which has been addressed in the correlation study is respirable dust mass concentration. In fulfillment of this objective, two mines operating in different coal seams have been selected for respirable dust mass sampling on both longwall panels and continuous mining sections. At present, sampling has been completed on the longwall panel operating in the first mine, and one half of the planned sampling has been accomplished on the continuous mining section.The first mine sampled is operating in the Pittsburgh coal seam. The average mining height is approximately 78"" with an average of 8"" of bottom shale being mined. The mine is primarily a longwall mine, and continuous mining machines are used to support the longwall.Figure 1 shows the layout of the longwall panel which was sampled. Intake air is coursed via the track heading up to the headgate area. The air splits at the headgate. Approximately 20,000-30,000 cubic feet of air per minute (CFM) is used to ventilate the longwall face and about 5,000-10,000 CFM is routed down the belt entry. Substantial leakage across the gob was noted during the sampling period. An average of 1800 CFM per 100 feet of face leaked through the shields into the gob from #1 shield to #112 shield. A substantial amount of leakage also occurred between the #1 shield and the solid rib of the headgate development panel. The path of the air used to ventilate the panel is shown with arrows in Figure 1. Direction of air flow was opposite to the coal moving direction on the armored face conveyor.A double-drum ranging shearer is used on the face to cut a 30-inch web of coal. Normal practice is to cut from the tailgate to headgate with the leading drum raised and the tail drum lowered for cutting bottom. After reaching the headgate, the shearer is reversed and both drums are lowered for a clean-up pass. The last 40 feet of face on the tailgate is cut on the clean-up pass.The shearer is equipped with 2 banks of 4 water sprays each and 2 large sprays on the headgate end and 1 bank of 4 sprays on the tailgate end. Additionally, sprays are located above bits on the cutting drums. Actual cutting speed was approximately 14-18 feet per minute, depending on conditions.The cross sectional area for air flow on the face was approximately 60 square feet before a pass was mined and 80 square feet after a pass was mined but before the shields were advanced. The cross sectional area at the shearer was about 35 square feet.The condition of both the tailgate and headgate of the panel was good with no signs of significant roof problems. The roof conditions along the face during the sampling period were variable. At times, as much as 3 feet of drawslate fell from the roof for a span of as much as 40 shields. Generally, however, relatively local areas of falling roof were encoun-tered, usually limited to a 10-20 shield span when appearing.Ten days were spent gathering respirable dust samples on the longwall panel. Mine Safety Appliance (MSA) sampling units equipped with 10-mm nylon cyclones, pre-weighed MSA PVC filters, and constant-flow DuPont pumps were used to obtain thesamples. The pumps were calibrated at a 2 liters-per-minute flow rate. The 10-mm cyclone was selected for classifying total dust into the desired respirable fraction in order to obtain ""legally defined"" respirable dust samples for detailed physical characterization."

Jan 1, 1988