Search Documents

Society of Economic Geologists, 65 East 56th St., Princeton, N. J. Edward Sampson, Secretary. Publications of the Society constitute a part of "Economic Geology," a semiquarterly journal published by: The Economic Geology Publishing Co., W. S. Bayley, Business Editor, University of Illinois, Urbana, Ill.

Jan 1, 1933

Jan 1, 1942

By Lawrence Dykers

The paper presents a generalized history of the growth and utilization of electronic data processing in a medium- size, mining-oriented company. A brief narrative outlines a corporate wide data gathering system, its hardware and application. Responsibility areas for corporate accounting, operations control, engineering, and research program development are defined. A Synopsis of programs within responsibility areas is presented along with a review of program language requirements for each of these areas. Anticipated additional uses of computers and the programs being developed for these uses are outlined. The scope and growth of an Information Systems Department within Duval Corporation is briefly discussed. Suggestions are presented which should help minimize the problems and avoid some of the pitfalls of program development for those contemplating the initiation or revision of an electronic data processing system. The importance of lucid and comprehensive program documentation is stressed.

Jan 1, 1969

By E. P. Gustafson

Demand by precious metals explorationists for cost effective means to target subsurface geologic structures worthy of evaluation by means of drilling has led to the use of the predictor-correlator technique. To locate polarizable targets, the predictor-a localized inhomogeneity in electrical properties-is placed at various locations in the computer-simulated subsurface region, and correlated with the potential distribution observed in the field. The correlation coefficient obtained is assigned to the subsurface location. IP targets are extracted by calculating a second correlation section based on higher-frequency illumination and subtracting it from the first. The locations of correlation difference correspond to the locations of polarizable mineralization.

Jan 1, 1989

By S. V. Volkova, S. V. Mamonov, T. P. Dresvyakyna

"The purpose of the work is complex processing of sulphide-magnetite ores with the separation of iron into iron concentrate, copper and noble metals into copper concentrate.The work shows the research results of the material composition of the sulfide-magnetite ore in the South part of the Peschanskoye deposit. According to the research results it is found that ore contains 0.59% of copper, 66% of which is related to chalcopyrite; 39.9% of iron, 81% of which is magnetite and 3.87% is sulfur, 42% of which is associated with pyrrhotite, 65% of which is a monoclinic modification. According to the results of the mineralogical analysis, it is found that the main iron-containing mineral in the ore under study is magnetite, the content of which is 45%. In addition to magnetite, iron is found in carbonates, pyroxenes, amphiboles, chalcopyrite, pyrrhotite and pyrite. The main copper mineral in the sample is chalcopyrite; covellite, chalcosine, bornite have a subordinate value. The total content of copper minerals in the sample is about 1%. The processing technology provides the three-stage grinding of the ore to a size of 65% of the class-71 µm; a cycle of copper flotation; a cycle of pyrrhotite flotation; wet magnetic separation of flotation hosts. The following optimal parameters are established for the ore under study: the alkalinity of the slurry is 250-280 g/m3 of free calcium oxide in the liquid phase of the slurry; the duration of the main copper flotation is 20 min; the consumption of butyl potassium xanthate is 20 g/t; the consumption of the foam generator T-92 is 15 g/t; the consumption of copper sulfate for the activation of pyrrhotite is 300 g/t; the magnetic field strength is 1500 Oersteds.A complex flotation-magnetic technology for the enrichment of sulfide-magnetite ore has been developed in the laboratory in order to produce a copper concentrate containing 21.6% of copper with 91.7% extraction and an iron concentrate with 66.5% of iron mass fraction and 1.2% of sulfur with an extraction of iron into the concentrate of 87.9%."

Jan 1, 2018

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By Y. H. Kim

A simulation procedure has been developed that realistically portrays aggregate growth and disintegration for particular types of floc structures in water and wastewater treatment processes. The procedure requires local dissipation rates and specification of an interaction distance between colliding particles. A principal difficulty encountered in polymer flocculation, however, arises from changes in conformation of adsorbed macromolecules. Therefore, in systems where polymer flocculation occurs by bridging, dynamic changes in the particle size distribution depend upon the interaction of nonlinear. stochastic hydrodynamics with particles whose growth results from a number of concurrent and sequential random processes.

Jan 1, 1988

No phase of the steel industry is more typical of its remark- able progress than is the evolution and development of the modern American blast furnace. The founding of the Institute in 1871 also marked the beginning of a new era in the pig-iron industry. The rapidly expanding westward development of the country, with its seemingly unlimited markets, gave rise to unprecedented demands for blast-furnace products. The manner in which the iron industry responded provides a fascinating chapter in the history of industrial development. Prior to this period, the iron industry of the United States, largely concentrated in the East, was based upon the consumption of local iron ores and local fuels, the latter predominately charcoal and anthracite. Small, isolated furnaces were located near scattered ore and fuel sources, and the completely integrated ironworks and steelworks were yet to be developed. In about 1860 exploitation of the newly discovered rich ore deposits in Michigan and the successful adaptation of blast furnaces to coke produced from coal of the great Pittsburgh seam in western Pennsylvania proved to be major factors in firmly establishing the general westward shift of the industry. But these were largely economic in character, and it was not until about 1870 that the aggressive, individualistic nature of the ironmaster asserted itself in no uncertain manner. No longer limited by relatively inadequate equipment and inferior raw materials, and spurred as well as encouraged by those who supplied capital for these new enterprises, furnacemen began to establish unheard of records in iron production. It is not surprising that Pittsburgh was the center of this new activity. Its tenor is best indicated by the following account :l

Jan 1, 1948

By C. O. Beale

This paper is the first part of a two-part review on the subject. , , .. Here reference is made to the place of copper among the elements, Its properties, Its historical significance, and its 'end uses both in general and in South Africa. Its current market situation and its prospects are dealt with briefly. Some account is then given of the mining and metallurgical techniques employed. in South Africa in the production of copper, together with the names of the companies at present Involved and brief descriptions of their operations, ,... . .. The operations of these companies are described In greater detail In Part 11(Apn11985 Issue of the Journal).

Jan 1, 1985

By Andy J. Robinson, Mark D. Claassen

Railroad companies and transit authorities have been slow to acknowledge that for many—utility crossings, a direct pipe installation below live rail can be just as effective as a more intrusive traditional cased crossing. Properly designed and specified pipe jacking work, and specifically pressure-balanced microtunneling, coupled with careful specification and analysis of geotechnical monitoring and, where necessary, ground improvement measures, can produce a low-risk, low ground movement solution to the needs of utility companies and municipalities whose services need to pass below urban and rural rail corridors. This paper discusses the design, geotechnical and ground improvement aspects of microtunnel crossings below active heavy and light rail lines and crossings beneath active subway tunnels.

Jan 1, 2003

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By Nigel Pearson, Malcolm J. McPherson

In the Grasberg Mine, a series of orepasses of diameter 2 to 4m are being constructed, each one to carry as much as 10,000 tlhour of copper- and gold-bearing ore through single stage vertical drops of over 500m. At the base of each orepass, the fragmented rock falls into an orebin of diameter 1 Om and 100m deep. Long before the planned tonnages were reached on the early orepasses, a problem arose that was both serious and intriguing. Pressurization of air in the orebins caused by the falling rock reached such levels that when the feed to the top of an orpass was interrupted, a massive surge of air ascended rapidly and produced a dangerous backblast accompanied by dust; grit and rock fragments from the top of the orepass. Backblasts lasted for about one minute and were not only hazardous to the health and safety of personnel but also required time-consuming clean-up operations. The paper describes the aerodynamic analyses that were con- ducted in order to understand fully the mechanisms involved in the phenomenum, and the development of a procedure that al- lows the effects of falling material to be incorporated into existing ventilation network software.

Jan 1, 1997

By Murphy MW, Klaric SD

The history, operation and design of the Secor continuous rod production process is described. The effective operation of the plant is influenced by accurate monitoring and control of molten metal properties, mould release application, coolant application and composition and correct setting of all operating parameters. The continuity of operations, which is an essential feature of this type of plant, is also greatly influenced by the service life of wear parts in the operation. This paper deals with three principal wear parts which come into direct contact with copper during operation, these are:

Jan 1, 1985

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

The successful exploration for Austin Taylor and Gen. McRae from 1931 to 1940 obscured the fact that I was reaching a period of transition. This was true both in personal and business life. It was probably fortunate that I did not realize how great a change must come after I passed the age of 50. In the personal life of our family the change came when both our children left home to go to school or college. This made home a different place and, because of the absence of the children, Dorothy could devote much of her time and attention to the art she loved so well. She could spend long periods in New York, the center of the nation's art life. Vacations at Tahoe and long pleasure trips made the separation from the children less disturbing but it could never again be the same as it had been in the first 20 years of our marriage. The change In my business life was just as complete, though a little more gradual. While work for Bralorne and General McRae made the "bite" of the Great Depression less painful for us than it was for most consultants and their families, the fact that I was getting older made a new sort of work inevitable. I was 50 years old and the total grew rapidly. Planes and automobiles that made travel easier even in the wilds of Alaska and northern Canada still made it possible for me to look at new prospects, but increasingly often I was exhausted at the end of a day's climb and, if the nature of my work did not change there would soon be no more work. Fortunately work of a new sort came a little at a time. As I became a director of Bralorne and president of its American subsidiaries I had to take on more administrative work, and success of these operations made others want to employ me to help direct policy and value mines. I was also asked to arbitrate contests between mines when technical disagreements were so great that judges or juries could obviously not understand them My consulting for government agencies helped to

Jan 1, 1976

By I Gray

This paper examines the effects of the changes in stress that a coal may undergo as part of the drainage process. As a consequence of this, some coal seams will come to the situation that they have zero horizontal stress existing within them at the time of mining. The hypothesis of this paper is that this lack of horizontal confining stress means that on mining, the vertical stresses may be easily raised to a level where failure occurs. This failure may be accompanied by significant energy release from energy stored within the coal as well as that coming from the roof and floor. To determine the state of stress within the coal seam, the concept of the effective stress path that the coal passes through is examined and is found to be very dependent on the shrinkage of the coal with degassing, the Young’s modulus of the coal and its Poisson’s ratio. The Young’s modulus of the coal is important and has been found to be highly dependent on the state of stress within the coal. It may change by more than an order of magnitude.CITATION:Gray, I, 2014. The consequences for pillar stability of zero confining stress brought about by forced or natural drainage, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014