Search Documents

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

A slag-metal equilibrium study of the system SnO-FeO-(Si02+Al2O3)/Sn-Fe was carried out at 1250°C. The distribution coefficient, k =(Sn/Fe)metal X (Fe/Sn)slag was found to range from 246 for an iron contentof 0·53 per cenrt in the metal to 82 for an iron content of 6·4 per cent. The value of the ratio ?SnO/?FeO was calculated and found to be approximately a function of per cent SnO in slag alone in the region (Si02+Al2O3)/ FeO = 0·4 to 1·2. Comparison with other published work suggests that the addition of CaO to slags having (SiO2+Al203)/FeO ratios of about 1·1 raises the value of ?SnO/?FeO...

Jan 1, 1974

CARACAS PETROLEUM Established February 24, 1957 Official year begins in January Harry J Sykes, Chairman G J Clarke, Vice-Chairman Robert S Longwell, Vice-Chairman David L Stepanek, Treasurer Robert C Newman, Secretary Texas Petroleum Co Apartado 267 Caracas, Venezuela

Jan 1, 1960

By E. Wm. Heinrich

Glass sands fall into that extremely select category of mineral deposits that requires a fantastic degree of natural concentration (95% +) of a single component before they can even be considered as ores suitable for further refinement. The combination of geological factors that has produced such an environment of "mineralogical single-mindedness" has appeared only rarely. Factors that require consideration in the economic evaluation of a potential glass-sand deposit can be grouped into three categories: 1) geological (e.g., size, shape, structure); 2) petrographic (e.g., grain size, accessory minerals, nature of iron contaminants); 3) geographic - political (e.g., proximity to consumer, size of market, zoning restrictions). Of particular con ern is the nature of the iron contamination. Iron-bearing species appear as 1) accessory mineral grains, either detrital or authigenic, 2) cements, 3) grain coatings, and 4) quartz-grain inclusions. Selection of the cheapest form of beneficiation requires precise information on the mineralogy of the iron species and their detailed petrography. Because of the antipathetic relationships, in many parts of the United States and Canada between the geographical locations of glass plants and the geological distribution of glass sands, the selection of ac suitable source for a particular glass plant may be dichotomous. One may seek either an exceedingly pure "classic" type glass sand that is relatively distant and whose cost includes a major transportation charge or a relatively proximate and somewhat "impure" source whose cost includes a substantial fee for beneficiation.

Jan 1, 1974

By W J. Rankin

Metals are well suited to sustainable development goals. They are not biodegradable and have virtually an unlimited lifespan and the potential for unlimited recyclability. Thus metals can be considered as renewable materials. However mineral resources, the source of primary metals, are ænon-renewableÆ as their supply is finite, but this does not necessarily mean scarcity. In this paper the results from a series of Life Cycle Assessments of primary metal production processes for copper, nickel, lead, zinc, aluminium and steel have been used to examine how metals may contribute to societyÆs transition to sustainable development. Particular issues considered include:current metal reserves and how these may change in the future; some of the environmental impacts (Total Energy, Global Warming Potential and Acidification Potential) associated with primary metal production and how they will be exacerbated by declining ore grades; new processing technologies with lower energy consumptions and improved metal extraction efficiencies that will reduce reserve depletion and environmental impacts; increasing the utilisation of æmetals in useÆ by recycling, with particular reference to aluminium; and the potential impact of a carbon tax on metal prices and how this may influence the ways in which metals are used in the future.

Jan 1, 2002

By R. A. D. Pattrick, D. A. Polya, D. J. Marsh, J. -J. Bao

"Abstract-The utility of high-density stream sediment and stream water sampling to the exploration for silver deposits was investigated by the study of the epithermal Ag-Au base-metal prospect at Lagalochan in western Scotland. The geology of Lagalochan is dominated by a calc-alkaline Caledonian intrusive complex emplaced into Dalradian Supergroup rocks (Harris et al., 1988a). The complex consists of subvolcanic porphyrytic rocks associated with intense hydrothermal alteration and brecciation. Early Cu-Ag-Mo-rich mineralization is found in the core of the complex with later Pb-Zn-Ag-Au-As-Sb-rich mineralization toward the margins (op. cit.).Stream sediment sample analysis spatially resolved the Cu-rich and Ag-rich mineralization. Ag and Cu anomalies relative to local background values were found in all size fractions analyzed (-125 µm, +125 µm, +180 µm, +250 µm) but the more pronounced anomalies were found in the -125 µm fraction. The coarser fractions generally revealed more erratic but longer dispersion trails. The separation of Cu-rich and Ag-rich mineralization is also apparent in the distribution of relatively high dissolved Cu and Ag in stream waters, particular when expressed relative to the solute load as Cu/TDS and Ag/TDS.The mineralization at Lagalochan is indicated by Ag, Cu and Pb stream sediment and water concentrations that are anomalous with respect to local backgrounds, but are difficult to distinguish from regional backgrounds. This emphasizes the further potential of high-density stream water sampling, in particular, as a viable geochemical exploration tool on a sub-regional scale for epithermal deposits in relatively unpolluted upland terranes."

Jan 1, 1995

By G. P. Chaudhari, F. Warchomicka, M. Dikovits, V. Pancholi, C. Poletti

"The hot formability of a microalloyed steel with 0.16 wt-%C modified with N is studied by using processing maps. Compression tests of cylindrical samples are carried out using a Gleeble®3800 simulator in the range of temperature between 750 -1000°C and strain rates between 0.01-100 S-1. For this alloy, an Ar3-temperature about 740°C is determined by means of dilatometry. Processing maps are calculated using the modified dynamic material model developed by Murty and Rao for different logarithmic strains. For the instability map, the parameter Kj developed by the authors in previous works is used and compared with other instability values. Softening in the flow curves provoked by induced ferrite during deformation at low temperatures and low strain rates is reflected in the n-value. Light optical microscopy (LOM) and electron back scattered diffraction (EBSD) measurements are used to study the microstructure of the hot deformed samples to determine the deformation mechanisms active and to verify the processing maps.IntroductionProcessing maps offer a good possibility to optimize thermomechanical process parameters and to avoid defects in the products. Prasad et al. [1] developed the processing maps using the dynamic material model (DMM) and Murty & Rao [2] modified it. Processing maps consist of two superimposed maps: the dissipation efficiency and the instability map. The processing maps can be used to detect areas with a good hot formability, which are normally related to restoration of the material by dynamic recovery/recrystallization. For a high dissipation efficiency value and no instabilities, a good hot formability is predicted. In the DMM no storage of energy takes place and so the material is considered essentially dissipative, this is only true for high temperatures and high strain rates [1]."

Jan 1, 2012

By Z. Zhongwei

The leaching kinetic of mechanically activated sphalerite with acid FeCl3 solution was investigated. The result has shown that mechanical pre-treatment has greatly enhanced the leaching process. Comparing with the original concentrate, the activated one can be leached more completely at relatively lower temperature with diluter FeCl3 concentration within a shorter leaching time. The activation energy for the activated concentrate is 27 KJ/mol, while for the original one is 52 KJ/mol.

Jan 1, 1995

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By F. A. Rutledge

"The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively pros¬pected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941.The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program.The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.During July 1943, the coal area in the immediate vicinity of Costello Creek was geologically and topographically mapped. by Clyde Wahrhaftig and Jacob Freedman, geologists, U. S. Geological Survey. F. A. Rutledge, mining engineer of the Bureau of Mines examined the property July 18 to 22, 1943, and a project of trenching, diamond drilling, and sampling was initiated on August 4, 1943. During the project Clyde Wahrhaftig remained at the Dunkle mine to interprets drill cores and assist the author in planning the explora¬tory program. The project was completed October 7, 1943.Field investigations were under the general direction of R. S. Sanford, acting chief, Alaska Branch, Mining Division. Coal analyses were made by Maurice L. Sharp, coal analyst for the Alaska Railroad.Special mention is made of the cooperation and assistance received from Clyde Wahrhaftig, geologist, U. S. Geological Survey.The many courtesies received from the owner, W. E. Dunkle, and the members of the Army Coal Procurement Section, Alaska. Department, also are acknowledged.The W. E. Dunkle coal mine is in the Broad Pass region on the south slope of the Alaska Range at an altitude of 2,800 feet (fig. 1). It is situated within the Third Judicial Division, headquarters of which is Valdez, Alaska. The area is situated approximately at latitude 63° 15' N. and longitude 149° 30' W. and is connected with the Alaska Railroad at Colorado Station by an 11-mile gravel road that is passable throughout the year. This road is maintained by the Alaska Road Commission. A private telephone line to Colorado Station connects with the telephone and telegraph service of the Alaskan Railroad.The passenger rate from Anchorage, Alaska, to Colorado station is $12.10. Freight rates are $1.60 a hundred pounds for heavy machinery and $2.66 a hundred pounds for first-class freight.The Costello Creek coal basin is in an area of low relief and has been dissected by numerous creeks flowing down the south flank of the Alaska Range. The Dunkle coal mine is on Coal Creek, a small tributary of Camp Creek, 1,000 feet from their junction. About 700 feet below this junction, Camp Creek joins Costello Creek, which in turn empties into Bull River 1/2 mile above the latter's confluence with the West Fork of the Chulitna River. The location of the mine is shown on figure 1."

Oct 1, 1948

By C. A. Herbert

"The Bureau of Mines for a number of years has conducted experiments at its experimental mine near Bruceton, Pennsylvania, on the explosibility of coal dust, with particular reference to dust explosions in coal mines, and the knowledge so rained may well be applied to the handling of coal dust at industrial plants and elsewhere.Powdered coal is coming into use more and more as a fuel, and the dangers incident to its use should be recognized and guarded against, as a number of accidents have occurred in recent years due to ignorance of this danger or to carelessness.Within the past three years two very serious accidents, under almost identical circumstances, have occurred on the surface at two different coal mines in Southeastern Iowa, due in each case to the sudden ignition of a cloud of fine coal dust.The first accident resulted in the burning of six men, three of them fatally; the second burned eleven; three men died as a result of their burns.The mines in the Southeastern part of Iowa, where these two disasters occurred, are operating in a thin coal bed averaging about three feet in thickness, and are worked on the long-wall advancing system similar to that of Northern Illinois.The miners in this section are paid on a screened coal basis; in other words, receive no pay for the fine coal. As a result they use forks in loading the coal into the mine cars, and naturally a considerable quantity of coal is left along the roadways. Subsequently this fine coal, together with the roof rock that is taken down to give sufficient height on the roadways, is loaded into cars and dumped in piles on the surface. This roof rock is a block, oily shale and the contribution of fine coal and oil shale gives ample combustible material to thoroughly burn the rock as it is dumped."

Jul 1, 1923

By Lloyd A. Morley

To reduce safety and production problems, it is essential that the electrical operating characteristics of coal mining equipment and their electrical subsystems be clearly understood. The Bureau of Mines and the Pennsylvania State University have developed techniques to monitor and analyze several of the critical parameters. A unique system for measuring traction locomotive consumption at the machine has been assembled and utilized. Conclusions from 27 continuous miners show that voltage levels are directly tied to machine efficiency. The Bureau of Mines and Pennsylvania State University, along with West Virginia University, are currently monitoring and accessing mine power transients. Results exhibit that voltage transients of three to five times the line -to-line value are common on underground distribution systems.

Jan 1, 1975

By D. Fourie

A brief history of channel sampling in South African gold mines is followed by a chronicle of different sampling events and sampling methods that used the traditional ?hammer and chisel? approach as well as diamond core extraction of the sample. The problems associated with each method of sample collection are documented and the use of a laser scanner to measure the exact volumes of sample material extracted from a correctly delimited sample site are considered. Areas where increment delimitation errors (IDEs), increment extraction errors (IEEs), increment weighting errors (IWEs), and increment preparation errors (IPEs) occur were investigated. A ?simulated chip sample model? is introduced and provides the basis for comparing the percentages of error introduced as a result of improper sampling. The heterogeneity experiment showed that reefs that are more homogenous tend have lower extraction errors than the more complex carbon-rich reefs, which may contribute to understanding the poor mine call factor on mines exploiting the latter types of reef. Keywords channel sampling, chip sampling, error, bias, modelling.

Jan 1, 2014

By V. Miller

Highly variable milling procedures within a geologically complex porphyry copper deposit owned by Kennecott Corp. in Nevada made it necessary to estimate copper recovery and concentrate grade in areas where actual test data was lacking. Estimation was made by first determining the relationships between desired metallurgical properties and the ore's petrology-copper mineral type, rock type, and copper grade. This relationship was then combined with previously estimated rock type, mineral type, and copper grade data in the mineral block model to predict milling properties.

Jan 1, 1985

By George E. Cole

Introduction In view of the fact that, during the past year, two Manitoba mines-Flin Fion and Sherritt Gordon-have entered the list of producers and have materially increased that Province's contribution to the metal production of the Dominion, it would seem appropriate at this time to review the progress of the industry in the Province, with particular reference to the out-standing metal-mining developments of the past decade. That these two mines have been able to continue their operations in spite of the low prices of copper and zinc adds a touch of brightness to the industrial life of the Province. Depression in metal prices is not encouraging to the mining industry, but it does stimulate efficiency in methods and costs of production. As two thriving towns have grown around the two mines, the will of the management to carry-on is of great consequence to Manitoba, this year so hard hit by the .agricultural depression. And, much as it is a pleasant feature in the mining situation that these mines have been able to continue operations, nevertheless it must be noted, in reviewing the mining developments of the past few years in Manitoba, that the Province was fortunate enough to profit by good times, in that an industry was established which gives evidence of permanency. In the metallic field, the section of Manitoba that first received attention from prospectors was the boundary district, west of the Lake of the Woods. Several claims were staked here at the time of the gold boom in the neighbouring Ontario area. But the first real interest in metalliferous deposits dates from the discovery of gold in March, 1911, in quartz veins on the shores of Rice lake, some twenty miles east of lake Winnipeg. Systematic and organized prospecting of the pre-Cambrian areas of the Province may be said to have commenced with that discovery. The first gold discovery in northern Manitoba was made at Wekusko (Herb) lake in 1914. This was followed by the discovery of the Flin Flan and Mandy copper ore-bodies in 1915 on Flin Fion and Schist lakes, respectively.

Jan 1, 1932

By David P. Reddick

Economics is a social science dealing with the allocation of scarce resources. In modern times the “science” was identified by Adam Smith in his book, The Wealth of Nations, written in 1776. Mr.Smith, highly influenced by the Mercantilists of the 17th and 18th centuries, identified the “Invisible Hand” which would lead every individual to pursue selfish rewards in purchasing goods. He speculated these selfish motives would result in the best good for all. Price would be determined by barter, at a point where self-centered customers and vendors were mutually satisfied. Today, Smith’s theory is known throughout the world as “Capitalism” but most often termed “Free Enterprise” in the United States.

Jan 1, 1992

Alternative processes for converting coal to liquid products and their stage of development are outlined. The merits of hydrogenationprocesses in general, and the solvent refined coal process in particular, are stressed. Bench scale experimental hydrogenation procedures used by the Australian Coal Industry Research Laboratories Ltd. (ACIRL) to study the liquefaction of Australian coals and correlations between properties of such coals and their conversion to liquid products are described. Factors involved in assessing investment and operating costs for modern hydrogenation based coal refineries of different capacities are described with reference to a recent study undertaken in N.S.W. The significance of coal properties such as yield and yield structure of total liquid products and how they and other factors can influence the economics of the coal refining operations are discussed.

Jan 1, 1977

By M. Sukhram

This paper presents a technique to determine the direction of velocity in liquid aluminum (Al) by measuring the temperature distribution within a cylindrical rod while it is inserted into the flow. The heating pattern of the rod is a result of the interaction of the thermal fields of the rod with the liquid Al. This interaction freezes aluminum onto the cylinder in a characteristic pattern and as a result the temperature response within the rod also follows a distinctive heating pattern. Monitoring the temperature within the cylindrical rod as a function of spatial and temporal coordinates, the direction of velocity can be inferred. Experimental research work involving liquid Al was conducted at the University of Toronto using the Revolving Liquid Metal Tank (RLMT). The RLMT is a resistance furnace which can hold up to 50kg of liquid Al. In this RLMT tangential velocities up to 0.35m1s can be generated. Experimental data for different superheat and magnitude of velocity demonstrate that the sensor records different heating patterns under different fluid flow conditions. Using the transient temperature information, the direction of velocity of the molten Al flow field can be detected.

Jan 1, 2011

By Alan D. Hoagland

The Flat Gap mine, are important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolonmite and accessory pyrite. There is local minor galena and very rare barite and fluorite.

Jan 10, 1962