Search Documents

By Prosser AP

The large body of knowledge about the relation between chemical process efficiency and mineralogical features is of only limited use. The profession ought to try to improve the methods of using information as well as adding to the knowledge. One attempt isòdescribed. Correlations between process efficiency factors and the mineralogical features of low- grade concentrates have been developed from both a theoretical analysis and experimental measurements. The ultimate recovery of a reactive phase in an inert matrix can be calcu- lated from simple measurements of the particle size, porosity and pore size of the concentrate, and the grain size of the reactive mineral., The rate of recovery, up to 98% recovery, can be calculated from simple measurements of particle size, porosity, proportion of reactive mineral and tortuosity. Some details are given. The correlations are of potential use in process selection and preliminary design. Satisfactory predictions have been made for near-ideal systems. Improvements in the measurement of pore size and tests on more realistic materials are required. The ultimate benefit of the correlations will be determined by the magnitude and frequency of the effects of mineralogical features other than those specified above.

Jan 1, 1975

By S. N. McIntosh

Column bioleaching was evaluated by the U.S. Bureau of Mines as a means of recovering manganese from a low-grade ore from the Three Kids deposit in Southern Nevada. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms. Diluted molasses medium was provided as nutrient for the microorganisms. The medium was recirculated through the ore bed until the sugars were spent. Two methods were evaluated to recover manganese from the sugar depleted bioleaching solution: (1) adsorption with a weak cation exchange resin followed by stripping and precipitation techniques, and (2) direct precipitation of the manganese using ammonium carbonate. Both methods removed up to 95 pct of the solubilized manganese from the medium as a carbonate salt. After manganese removal, the medium was replenished with fresh molasses and recycled back through the column. More manganese was effectively leached. This process of manganese solubilization and recovery followed by replenishment and recycling of the medium was repeated until 98 pct manganese was extracted from the ore.

Jan 1, 1993

By R. H. Fett

T HE APPROACH to maintenance must always be ?completely positive: there must be no question of putting off difficult problems until it is more convenient to tackle them. By this it is meant that a piece of machinery or equipment which, by experience, is known to be due for a check should not, merely because it appears to be operating satisfactorily, be left until it reaches a critical .condition and breaks down. The mentality of the Maintenance Manager must be completely orderly and methodical and he should, in fact, possess a ledger-book mind, having a debit and credit outlook. The debit side would be that applying to time out of service, cost in wages, material, personnel involved, etc., and the credit side that relating to continuous operational time of the locomotive and therefore to the ultimate benefit of the mine and the personnel who work there. The Maintenance Manager is not concerned with design problems, and although he and the personnel under his jurisdiction are not engaged in productive work, he and his staff do, nevertheless, add greatly to or detract from the overall efficiency of the organization. Provided the machinery placed in his care is good to start with, he must take the best steps he possibly can to keep it running. However, he may, on occasion, be forced to improvise and this is where the ingenuity of a clever man rises to the occasion.

Jan 1, 1956

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By H. B. Goodrich

In considering historically oil development in Oklahoma, it must be recognized that basic evolutionary factors interlock and have an effect in common throughout the whole oil industry, regardless of locality or minor problems. Oklahoma, as the third in rank of oil-producing states (Texas being first and California second in production for 1929) has, like the rest, advanced to at least a partial recognition of the words, "Conservation," "Unitization," "Curtailment," "Prora-tion," and especially "Cooperation." Whether through altruism (of which there have been examples) or by exercise of good business common sense, Oklahoma operators realize that the oil business can run itself by cooperative action for the good of all. In this long-continued period of overproduction, Oklahoma has brought the advancing output down to limit of market requirements at least temporarily. Sources of Statistical Data For this paper, figures published by four recognized authorities were consulted. Between themselves these vary only a negligible per cent, in their totals. To be consistent, and on account of earlier availability the estimates published by the Oil and Gas Journal are mainly used herein, supplemented from other public and private sources. General Oil ProdCction in Oklahoma In 1927 Oklahoma's peak of all years was 276,022,024 barrels. In 1928 Oklahoma's total production was 247,500,851 barrels. In 1929 Oklahoma's total production was 252,229,474 barrels. The efforts of proration and curtailment programs on flush and semi-flush districts such as Greater Seminole, Oklahoma City, Logan County and others, with the natural decline of older pools, kept 1929 below 1927, but still the total was greater than in 1928. The total United States production for 1929 is herein taken as estiiated at 1,004,266,723 bbl.† Oklahoma produced 25.1 per cent. Of

Jan 1, 1930

By J Mauk, J Rowland, S Rabone

Most epithermal Au-Ag deposits in the Hauraki Goldfield are hosted in late Miocene andesites. Broken Hills is an exception, being one of the few economic deposits hosted in rhyolite. Investigation of Broken Hills provides the opportunity to collate structural data that may be compared with that collected from andesite-hosted deposits in order to evaluate the importance of rock type on vein development. The rhyolite host rock at Broken Hills is strongly flow-banded, but this anisotropy does not appear to affect the orientation of mineralised structures. There is a range of structures at Broken Hills: veins, faults, fractures, and large breccia pipes. Veins generally strike north-south, with localised changes in strike and thickness. Slip vectors determined from striations indicate near pure dipslip on the main lode, indicating an extensional tectonic setting. The orientations of vein deflections are parallel to slip vectors. This correlation is common in modern extensional fault arrays where fault growth and linkage produces subvertical deflections in fault orientation (eg TVZ). There are three main types of breccias: 1. Primary breccias related to rhyolite emplacement. 2. Jigsaw type secondary breccias that are that developed during the life of the hydrothermal system. 3. Breccia pipes. Broken Hills was a dynamic epithermal mineralising system.

Jan 1, 2003

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By T E. Norgate

Salinity in Australia is caused by over irrigation and land clearing for agricultural use over the last 100 years. It is now the biggest threat to the quality of land and water in the Murray Darling Basin and Western Australia. Pumping the saline waters straight into the ocean or transporting the solid residue (mainly sodium chloride) to the ocean after evaporation of the water is expected to cost the taxpayer millions of dollars every year. This paper proposes that the salinity problem of Australia, at least in part, can be converted to an asset rather than a liability if it is exploited and used to make value-added products. The more value made out of saline waters, the more saline water is processed and therefore the more salt is extracted from the land. The value-added products that can be made out of saline waters are numerous and diverse. Rough calculations show that value addition to the saline waters could potentially generate up to $A 200 million per annum business in the Murray-Darling Basin. Although it is a challenge to make cost competitive products and find markets for these products it is possible that up to $A 100 million per year may be gained from import substitution. Value addition to salinity would also reduce the threat on the environment and existing agricultural industry. Investment to add value to salinity will create business in the region, nurture the local small population communities, and increase services and long-term employment.

Jan 1, 2002

By Gustavo García

En esta investigación se plantea una metodología de planificación estratégica de una operación minera que incluye el tiempo en el valor del bloque; es decir, basada en múltiples corridas sucesivas de planes mineros con diferentes conjuntos de fases de minados. Su objetivo de optimización está regido por el valor presente neto de cada bloque del modelo económico, sometido varias veces a la versión mejorada del algoritmo de Lerchs y Grossman, pseudoflow, de manera que se mejoran enormemente los tiempos de estimación de las nuevas propuestas de fases de minado. Asimismo, al hacer uso de la programación lineal entera mixta, se consigue el plan minero óptimo de mayor valor presente neto.

Sep 20, 2019

By P. Fleming, W. Pascheto

"Rod mills processing nickel and copper ore experienced recurring failures of liner bolts. In some cases failures became very frequent, requiring constant mill intervention and consequently impacting process stability and operating costs. Investigation related to the causes of bolt failures involved a multidisciplinary approach with the participation of engineering, maintenance and operation. It included the determination of bolt failure mechanisms as well as the assessment of mechanical properties, fabrication quality and handling and installation procedures. In addition, other parameters affecting bolt performance such as mill and liner design, operating parameters and maintenance practices were studied. This paper reports the failure investigation results and proposed solutions for failure prevention. INTRODUCTIONOccasional liner bolt failures are common in rod mills. However, chronic bolt failures developed in rod mills processing nickel and copper ore caused frequent shutdowns for bolt replacement to an extent that affected process stability. At first, it was thought that the cause of recurring failures was related to bolt quality. The operation then submitted several failed bolts to failure analysis. However, it became apparent that bolt quality was unlikely to be the main cause of failures. The determination of root cause (s) then became more complex, requiring a multi-disciplinary approach to failure investigation, requiring the assessment of bolt installation methods, mill design, operating conditions and maintenance practices. The results of the metallurgical failure analysis and investigation of other possible causes of failures are reported here."

Jan 1, 2016

By David Bigby

The paper describes research undertaken on an ECSC/K HSE project which investigated several potential physical principles which might be harnessed to provide a non-intrusive means of determining the extent of failure in the near roof of mine roadways and tested the most promising in the laboratory and in the field. It was concluded that the principles which warranted further development were thermal response and laser vibration measurement. In the latter case there is a need to develop an efficient means of imparting energy to the seam to induce sufficient vibration. A new, SIMRAC funded Project will progress work in the field of thermal response.

Jan 1, 2004

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation's critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

By H. W. Hardinge

Disregarding for the present the economic side of a new device, let us turn to that feature of the conical pebble-mill which is of interest from a scientific point of view, and consider the device as a puzzle in which the theories of the cylindrical type of mill have been increased. Many articles have been written on the theory of the tube-mill, and explanations have been made which do not explain ; but these have evolved suggestions of practice which have resulted in changes in the tube as to length, diameter, feed, discharge, speed of rotation, rotation on hollow trunnions, rotation on rings, and changes in the operation as to quantity and size of pebbles, charge of load above or below the axis, crushing by causing the larger pieces of the material of the charge to act as grinders, whether crushing is abrasive or impactive, etc. The practical worker in crushing. is first interested in the endeavor to reach an econonlic means of accomplishing a desired end; but the improvements in crushing-practice have been largely left to the manufacturer of machinery, who, as a rule, has little, if any, knowledge of the specific requirements— such as granulation, sizing for concentration without pulverizing the metals, instead of pulverizing the rock or gangue; the metals being the more friable, while the rock is tough and not so easily disintegrated. A reversal of this practice is the aim of sliming direct for cyanidation or pulverizing for cement, etc. In the ordinary cylindrical mill, having a diameter of 4 or

Jan 1, 1909

By Waldemar Lindgren

I. INTRODUCTION AT the time of the discovery of America the old world had a scant supply-of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the nines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia and some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon wade the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 4, 1916

By J. Randel Hill

The 64th Texas Legislature passed the "Texas Surface Mining and Reclamation Act," Chapter 131, Texas Natural Resources Code (subsequently referred to as "the Act"), at a point in time when little surface mining had taken place within the state. Thus, enactment of regulatory control governing mining operations in our state has, for the most part, preceded widespread, intensive mining activity. I should point out that the statute applies only to the extraction of coal, lignite, uranium and uranium ore. A recent opinion rendered by the Attorney General's office has stated that extraction of the named elements, when it occurs incidental to the extraction of other materials, e.g., clay, is not not an activity subject to the Act. An important theme of the Act, frequently overlooked in other environmentally oriented legislation, is recognition of the Act's affect on the mining industry. The Act states that "the extraction of minerals by surface mining operations is a basic and essential activity making an important contribution to the economic well-being of the state and nation" and, in reference to reclamation being accomplished contemporaneously with mining, provides a recognition that "the extraction of minerals by responsible mining operations is an essential and beneficial economic activity." This legislative recognition is, of course balanced against the need for proper mined land reclamation, the rights of surface owners, the need to guard against unreasonable degradation to land and water resources and numerous other actions or events that the Legislature wanted protected. Another rather pervasive general theme that is established in the Act is the concept that the agency is entitled to obtain whatever information, or take whatever action, that appears reasonably necessary to effectuate the purposes of the Act. This concept, coupled with the detailed requirements placed on mining operations in the portions of the Act dealing with Permit Applications, Reclamation Plan and Reclamation Standards, easily insures that surface mining activities can and will be regulated to the extent necessary. Section 131.102(b)(2) is probably the most relevant provision in the Act which deals with the preclusion of mined lands becoming waste lands. This portion of the Act states that the surface mining operator shall: ". . . restore the land affected to the same or a substantially beneficial condition. ." In this language the Legislature had made it abundantly clear that the abandoned or orphaned lands found in some of the Eastern states, will not be tolerated in this State, and provided the Commission with a degree of latitude to determine what condition would be appropriate in each individual mining situation. I bring this area of the Act to your attention because it is the area which has received the most inquiries and concern by operators, i.e. what does "substantially beneficial" constitute? The Commission's staff has spent a considerable amount of time wrestling with the statutory language "substantially beneficial" to determine the legislative intent and provide operators with guidance of what they can expect. In this regard, the most definitive criteria in our opinion lies in the Act's legislative hsitory. The Legislature had before it basically three reclamation standards namely: House Bill 656, considered to provide the most stringent reclamation standard and identical to Senate Bill 66; House Bill 1717 which was supported by industry spokesmen and was considered to contain the least stringent reclamation standard; and Senate Bill 55 which was adopted by the Legislature. During the Bill's initial hearing before the House Environmental Affairs Committee, the House sponsor of the Senate Bill 55, which was the Bill eventually adopted, made the following statement: (I am quoting verbatim from the Committee's transcript although substituting the speaker's reference to the authors names with the Bill's numbers.) "An example of the differing approaches of the four bills can be seen in the area of reclamation standards and this is critical. House Bill 656, talking about restoring the surface of the land, House Bill 656 has this statement: 'At least fully capable of supporting the use to which it was capable of supporting prior to any mining or any higher or better use.' In other words you have to restore it to the level it was prior to the mining. Senate Bill 55: 'Restore the land to the same or substantially beneficial use.' Substantially beneficial use. (Emphasis his) House Bill 1717 says: 'Restore insofar as practical to appropriate beneficial post-mining use.' So that House Bill 1717 said to, 'restore insofar as practical to appropriate beneficial use. I think that's too weak, whereas I think the House Bill 656 that would call you to restore it to at least the use it had prior to the mining may also be too tight the other way. I think the Senate Bill 55 approach is down the middle of the road which says that you do restore it to the 'same or substantially beneficial use,' is a proper way to go there." Therefore, the conclusion that we have drawn from the legislative history of the bill is that the extent of reclamation required by "substantially beneficial" may be something other than the use it was prior to

Jan 1, 1979

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

Sedimentation is used to clarify process effluents or to thicken process slurries. The sedimentation cycle of a suspension is presented as a settling curve. This curve is simply a plot of the height of the interface between the settled suspension and clear liquor versus time. Figure 1 shows a series of graduate cylinders which contain a suspension at various stages in its settling cycle. Cylinder 1 shows the suspension completely mixed at time zero. After a brief period of time (see cylinder 2), the suspension is observed to settle from its initial height Ho to height H1, leaving behind a volume of clear (or turbid) liquor, called the supernatant. The interface between the supernatant and suspension is termed the mud line. It is also possible to distinguish at the bottom of the cylinder a layer of sludge representing solids which have settled from the suspension. The interface between it and the suspension is called the sludge line. The sludge line moves upward in the cylinder.

Jan 1, 1992

Accurately measure time of detonation and explosive detonation velocity in a blasthole for analysis of explosive performance and delay intervals. Approach A blasthole-monitoring fiber optic probe was developed consisting of filer optic cable to carry the fight and a sensor to detect and convert the light signals into electrical signals. Events can then be recorded on an oscilloscope, tape recorder, digital computer, or start-and-stop timer. This method is simpler to use and more immune to electronic noise than existing resistance techniques. The fiber optic material,, are inexpensive and easy to obtain, and the recording devices, such as storage oscilloscopes, arc available or easy to obtain. The probe provides the mining industry, explosive manufacturers, and those studying blasting, with a practical alternative to complex and expensive coaxial cable reflectometry, resistor strings, or resistance wire methods for determining explosive and detonator performance. How It Works The fiber optic cable is a plastic light guide consisting of sixteen 0.01-inch-diameter optic strands having an overall outside diameter of 0.087 inch. The receiver module incorporates a photodiode to detect the signal and an integrated circuit receiver for signal amplification into one package about 1/2 by 5/8 by 7/8 inch.

Jan 1, 1989

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 44,015 employees worked in underground mining locations in 2003, corresponding to 44,778 full-time equivalent (FTE) workers. • Ninety percent of underground employees (n = 39,735) were mine operator employees. • Contractors comprised 10% of all underground mining employees (n = 4,280) and comprised only 5.8% of all underground FTEs. • The majority of underground employees worked for coal operators (73.0%; n = 32,130).

Feb 1, 2005