Search Documents

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

By James H. Aase

Selected glacial lake clay deposits in Minnesota were sampled, tested, and evaluated to determine their suitability for use as a bonding agent in iron ore pellet manufacturing. Preliminary tests conducted on clay samples obtained from five ancient glacial lake basins identified the clays in the Lake Agassiz glacial lake basin near Cook, Minn., as having the greatest bonding potential. An auger drilling program was conducted to obtain substantial quantities of representative material for detailed testing. The drilling indicated the presence of large clay reserves in excess of 500 million tons within the 12-square-mile area investigated. Bench scale tests indicated that the bonding properties of Cook area clays, when activated with relatively small quantities of sodium carbonate monohydrate (Na2C03?H2O), imparted excellent strength characteristics to iron ore pellets. Larger scale continuous pelletizing tests were made to confirm the bench scale results. These tests indicated that use of 1 percent activated clay alone as binder gave the iron ore pellets an overall strength slightly lower than with 0.75 percent bentonite, considered the industry standard. Use of 0.5 percent activated clay plus 0.5 percent bentonite produced better pellet strength qualities than use of 0.75 percent bentonite alone, without increasing the silica plus alumina content. The data from both bench scale and larger scale continuous tests suggest that the Cook, Minn., clays can be utilized after activation either alone or in combination with bentonite at an economic advantage over present pelletizing practice with bentonite.

Jan 1, 1968

By Frank Firmstone

IN Chemical Phenomena of Iron Iron Smelting, Mr. Bell gives the weight of materials required to fill furnaces of various sizes at the Clarence Works ; as this differs very much from the weight required for furnaces at Glendon, where anthracite and in agnetic and brown iron-ores are used, a comparison is interesting. Taking furnaces at Glendon of 4800 and 11,900 cubic feet capacity and comparing them with the Clarence furnaces of 6000 cubic feet and 11,500 cubic feet, we find that the 4800 cubic feet at Glendon and the 6000 cubic feet at Clarence required respectively

By M. Cross

INTRODUCTION The results of the Japanese dissective investigations have [l-4] transformed our understanding of how the blast furnace operates. These studies revealed an internal structure of the furnace burden with five main zones, as illustrated in Figure 1. In the granular zone the charged material retains its structure whereas in the cohesive zone the iron ore particles are at advanced stages of reduction and form a semi-molten mass with a relatively high flow resistance. In the active coke zone molten iron and slag flow through a matrix of loosely packed coke. The raceway is a relatively small void space generated by displacement of coke due to the hot blast momentum, whilst the hearth is packed with coke, slag and molten iron. [ ] It is now well appreciated that furnace control is largely achieved and maintained by using the burden charge distribution to determine the gas glow distribution within the furnace and, hence, the shape and extent of the cohesive zone. In fact, Wakayama et a1 [5] of Nippon Steel Corporation state that optimum furnace operation is synonomous with the formation of a desirable cohesive zone shape, which in turn is almost solely determined by the burden charge distribution and its mechanical properties [6]. Much of the development work on operating furnaces since the dissective investigations has been oriented towards the identification of external furnace measures which reliably predict the shape of the cohesive zone. Currently the most popular measures are top gas temperature, velocity and CO/CO, ratio profiles [5]. More recently pressure distributions as evaluated from a series of wall measurements down the height of the furnace are also being utilised [7] to identify the position and shape of the cohesive zone. A great deal of emphasis has been placed upon achieving a consistent quality in the burden charge materials, establishing a suitable set of operating conditions and only making changes when forced to, ie., the operation for some reason moves outside a desired operating range or the production requirements change. Operational control schemes based upon this philosophy (eg., Kawasaki's GO-STOP system [8]) have been remarkably successful at achieving both high production rates and relatively low fuel costs. Mathematical models have long been used as tools to assist in the analysis of the blast furnace process. Although, the models have been useful in post-operative analysis and for identifying trends, etc., they have not proved reliable for detailed design criteria or as the basis for effective control schemes. Such mathematical models have moved from simple statistical correlation, through overall and stagewise heat-and-mass balance calcu-

Jan 1, 1984

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019

During the year terminating at the date for the third annual meeting of Engineering Foundation, the Board completed, its undertaking to sustain the National Research Council for one year. Assistance given in the organization of the National Research Council has been amply justified by the results. The Council is now well established in a 4¬story building at 1023 16th Street, N. W., Washington, and has recently secured another similar building near by in order to house its increasing force. The breadth, importance and volume of work done have steadily grown. Foreign offices have recently been established in London and Paris, Dr. H. A. Bumstead being in charge of the former and Dr. William F. Durand of the latter. The total expenditure by Engineering Foundation for the National Research Council was $9,036, derived partly from income of the endowment fund and partly from special gifts from Ambrose Swasey and Edward D. Adams. In May, Walter M. Gilbert was appointed Assistant Secretary of Engineering. Foundation, with headquarters in Washington, his services being contributed by the Carnegie Institution. He also became and has remained to date Assistant Secretary of the National Research Council. In September, resolutions were exchanged between the Engineering Foundation Board and the National Research Council, setting forth a policy of continuing reciprocal relationship, and a conference committee, Chairman M. I. Pupin, Dr. Charles Warren Hunt, and Gano Dunn, was appointed to inform the National Research Council of the readiness of Engineering Foundation to work upon definite problems sug-gested by the Council. No problems have yet been suggested.

Jan 5, 1918

By J. P. Grieco, F. W. Grieco

"Manufacturing of Jaw CrushersOriginIn 1858 Eli Whitney Blake invented the first successful mechanical rock breaker-the Blake-type jaw crusher. Blake adapted a mechanical principal, the powerful toggle linkage system used to transform rotating motion and energy into oscillating mot ion and tremendous compressive forces. Today these same principals apply and the basic Blake-type jaw crusher is one of the leading machines of its class for heavy duty primary crushing service.In 1881 Philetus W. Gates patented a design for a crusher, the forerunner of the modern gyratory crusher which dominated the field from the late 1800s to the early 1900s. In 1910 the largest gyratory crushers built had 48-inch openings. However, about this time the jaw crusher came to life when the Power and Mining Machinery Co. built an even larger sized opening crusher-a giant 84-inch by 60-inch jaw crusher for a trap rock quarry in Pennsylvania. A 24-inch gyratory crusher became the ideal sized secondary machine for this size jaw. From that time on jaw crushers were looked on favourably as primary breakers and lines were brought up to date to parallel the already developed gyratory lines.FunctionMost heavy duty Blake-type jaw crushers work basically the same way. They are ruggedly designed and capable of crushing material in some cases in excess of 80, 000 p.s.i. compressive strength. They are very simple machines with few moving part s and, with the exception of replacement of renewable parts, are relatively maintenance free. It is quite common to have these machines in product ion for 20 to 30 years. The following will de scribe how these machines work. Large-diameter high-inertia flywheels which are connected to the main eccentric shaft, rotate inside a connecting rod type mechanism called a Pitman. It transforms rotating motion into vertical oscillating motion. This vertical motion is in turn transformed into reciprocating mot ion by means of a system of 2 toggles, each connected to the Pitman. The rear toggle is connected to the fixed rear head, and the front toggle is connected to the swing jaw which is hinged at the top of the crusher. With each rotation of the eccentric shaft the swing jaw opens and closes on rock which is fed into the crusher chamber, crushing the rock in a series of bites. These bites, or strokes as the y are called, usually vary between 1/2 inch to 1 1/2 inch at speeds of 120 to 200 strokes per minute. The reduction ratio of feed input to discharge is usually about 8 to I. Output capacities can vary from 100 tons/hour to 1200 tons/hour depending on the size of machine and its discharge opening. Horsepower requirements can vary from 75 hp to 400 hp.The entire crusher chamber is lined with replaceable 14070 manganese steel liner plates. This material is ideally suited for the job since it hardens as it wears during crusher operation. Manganese is also used in the high wear areas at each end of the toggle plates."

Jan 1, 1985

By Rildo Rodríguez, Dante Soberon

En el presente estudio se ha tomado en consideración diferentes aspectos geológicos que ayudan a determinar importantes controles estructurales que estuvieron activos en diferentes etapas de la evolución andina. El reflejo de la actividad de estas fallas se manifiesta por la presencia de controles estratigráficos, cambio brusco en la dirección de los ejes de pliegues y emplazamiento de pequeños cuerpos magmáticos, así mismo se encuentran relacionado al emplazamiento de mineralización de estaño, oro, uranio y tierras raras.

May 1, 2008

By M. R. Geer, H. F. Yancey

"INTRODUCTION The increased use of coal as pulverized fuel has focused attention on the grindability of coal and on the necessity of evaluating this property by a method suitable for use in the usual coal-testing laboratory. Without some knowledge of how various coals behave in the grinding operation, that is, how their use affects mill capacity and power requirements, the selection of coals for pulverized-fuel plants cannot be made on the same critical basis used in selecting coals for other types of burning equipment. The grindability of a coal, serves principally as an indication of the mill capacity attainable in grinding it - not as a direct index of the total cost of grinding. Although the grindability of coal may play a minor role at some plants, it is a decidedly important factor where pulverizer capacity limits the ability to carry high loads.Purpose Standardized tests for determining the grindability of coal are relatively new, so that the information now available on the grindability of various coals is limited in comparison, for example, with that available on proximate analyses. Published information is restricted to determinations on many important Eastern coals by the Fuel Engineering Co. of New York, 4/ a bulletin giving the results of numerous tests by the Babcock and Wilcox Co. 5/, and a comprehensive report on. Alabama coals by the Bureau of Mines. 6/This report presents the results of grindability tests of 34 samples of coals from Illinois, Kentucky, Pennsylvania, Utah, Virginia, Washington, West Virginia, and British Columbia at the Northwest Experiment Station of the Bureau of Mines, Seattle, Wash., in cooperation with the College of Mines of the University of Washington. In the future, as the laboratories of the Bureau make grindalility tests of other coals, additional reports will be issued."

Jul 1, 1938

By Michael D. McGill, Jeff Freadrich

There are many factors which affect the productivity of a front end loader. One of the most obvious is the characteristics of the material being mined. Characteristics such as size distribution, swell factor or heave, and material hardness / abrasiveness will all effect the efficiency of the mucking cycle. The focus of this paper is to look specifically at the size distribution of blasted material, and quantify the effects on loader productivity.

Jan 1, 1994

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By J. C. Gathje

Newmont&apos;s Phoenix Project is located near Battle Mountain, Nevada and is scheduled to produce copper concentrates containing high precious metal values. High temperature pressure oxidation (PDX) of the concentrates was considered as a treatment option during process development. The metals content in Phoenix concentrates range from: 15-25% for Cu, 1-10% for Zn, 0-2% for Pb and ?27% Fe. The precious metals content of the Phoenix concentrates can range up to ?300 g/t Au and >3,000 g/t Ag. As a consequence it was necessary that any process for consideration should have the capability of recovering both the copper and precious metal values. Typically, gold can easily be leached from the autoclave discharge solids, but silver is chemically bound with the jarosite formed and cannot be directly leached. Laboratory investigations led to the development of a patented PDX process that minimizes the formation of jarosite so that the silver can be leached easily along with the gold. The process was confirmed with extensive pilot plant testing. Excellent solution extraction of copper and zinc was achieved, and both iron and lead were precipitated in the PDX residue. The process produces clean PDX discharge liquors with very low iron concentrations. As an example, conventional PDX techniques resulted in pregnant liquors containing ?5 g/L Fe. However, the Newmont process, which controls the iron and sulfate species, achieved high iron precipitation in the PDX solids and pregnant liquors containing <0.5 g/L Fe. High gold and silver recoveries were achieved by direct cyanidation of the PDX solids. This process has the added benefit of producing PDX solids that demonstrate superior settling and filtration characteristics.

Jan 1, 2006

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By B. Ceccarelli

Many public domain programs useful in mining engineering, e.g., MULSIM, DZTAB, and EXPAREA, require tedious data input and generate pages and pages of printed output. To eliminate the tedium and to enhance the output, ETI U.S., Inc. developed GEM, Graphics for Engineering and Mining, a collection of application programs and underlying interface tools for VAX/VMS computers. This paper presents an example of how an application program in GEM enhances a specific public domain program. It describes how GEM provides automated graphics assisted input and output. The paper describes how this program uses the GEM User Interface: the 3D GKS device independent graphics, server and drivers, various mining, mathematical and statistical algorithms, the means of handling graphics, data including IGES, and the foreign language interface.

Jan 1, 1992

The surface properties of eight coal samples were studied by measuring contact angles, coal oxidation, equilibrium moisture and film flotation. The penetration tests were carried out with do de cane, while dodecane and MIBC were utilized in batch flotation tests and in the simplified release analysis. Coal floatability results from the properties of coal organic matter and coal liberation. While the wetting of coal by water seems to be determined by the surface properties of coal organic matter, wetting by hydrocarbons correlates very well with the content of coal mineral matter.

Jan 1, 1992

By Konrad Stern

The terms asphalt and bitumen have been applied interchangeably, although incorrectly on occasion, for centuries to various bituminous materials that were found in nature. Native bituminous materials of only the solid types, deposits of which are found on or near the surface of the ground, together with the principal asphaltic type petroleum bitumens will be considered in this chapter. The international dictionary compiled by the "Permanent International Association of Road Congresses" still gives the full name as "Asphaltic Bitumen" but of recent years the word "Bitumen" has been recognized as most appropriate and is defined by the American Society for Testing Materials as follows: "Mixtures of hydrocarbons of natural or pyrogenous origin, or combinations of both, frequently accompanied by their nonmetallic derivatives, which may be gaseous, liquid, semisolid or solid and which are completely soluble in carbon disulfide." Asphaltic pyrobitumens, as defined by Abraham,2 is a species of pyrobitumen, including dark-colored, comparatively hard and nonvolatile solids; composed of hydrocarbons, substantially free from oxygenated bodies; sometimes associated with mineral matter, the nonmineral constituents being infusible and largely insoluble in carbon disulfide. Deposits of native bituminous materials are found scattered over the entire world, but many are relatively unimportant as far as commerce is concerned. No attempt has been made to cover all of the known deposits. The principal bituminous materials of commercial interest are: 1. Native asphalts, solid or semisolid, associated with mineral matter such as Trinidad Lake asphalt, Rock asphalt and Selenitza, Boeton and Iraq asphalts. 2. Native Asphaltites, such as gilsonite, grahamite and glance pitch, conspicuous by their hardness, brittleness and comparatively high softening point. 3. Asphaltic bitumens obtained from nonasphaltic, semi-asphaltic and asphaltic crude petroleum by distillation, blowing with air and the cracking of residual oils. 4. Asphaltic pyrobitumens of which wurtzilite and elaterite are of chief interest industrially as they depolymerize upon heating, becoming fusible and soluble in contrast to their original properties in these respects.2 5. Mineral waxes, such as ozokerite, characterized by their high crystallizable paraffine content. Native Lake Asphalt At Brighton situated in the southwestern part of the Island of Trinidad is one of the largest deposits of native asphalt in the world.3 The lake is oval in shape, covering an area of 114 acres and having a depth of 285 ft at its center. The material forming this deposit is an emulsion of water and bitumen with a suspension of mineral matter consisting of impalpably fine clay dispersed by nature in the asphalt, and small quantities of silica and vegetable matter. The entire mass of asphalt is in slow but constant motion as evidenced by the migration of islands of vegetation from one place to an-

Jan 1, 1960

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

Western Mining Corporation, managing partner of the Windarra Nickel Project are in- stalling a raise-bored haulage shaft and under- ground crushing system at the Mt. Windarra Nickel Mine. The system will be the second of its type installed by W.M.C., the first being in- stalled at the Otter-Juan mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limi- tations, and escalating costs of a deep decline mine. The Windarra haulage system required a single 3m diameter vertical raise drill hole to a depth of 470 metres. Two five tonne skips in balance will hoist crushed ore and mullock to the surface, at a design rate of 200 tonnes per hour, effectively reducing truck haulage leads by up to 50%. It is expected the project will be in full operation by mid 1982 and will enable the mine to achieve an annual production rate of 600,000 t.p.a. by 1983.

Jan 1, 1982

By Joel K. Waterland

The Homestake Mining Company at Lead, South Dakota is one of the few remaining gold properties still in operation, in this country. The mine is relatively deep, with a bottom production level of 4250 feet, and a bottom development of 6200 feet. 4, 800 tons of ore are produced daily from three rather large, but inconsistent ore bodies; the dip of which is easterly at about 72 degrees, and the plunge to the south is about 30 degrees. The ore is, for the most part, a chlorite schist with large veins of secondary quartz and cummingtonite schist The ore is not continuous in any direction, but is localized at the ridges of the very intricate system of anti clinal folds. This property has been in active production since its establishment in 1876, except for a period during World War II. The incentive, or contract pay system, has been a gradual process that has been developed by the trial-and-error method down through the years. In looking over the old records, hand-shoveling was paid on an incentive basis as far back as 1916. Since this time, the contract system has grown until it now includes almost all types of underground work - except haulage and maintenance work

Jan 1, 1960

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

A borehole sonde using a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed. With the sonde stationary at points above, in, and below the coal bed, capture gamma rays were measured to show the variation in concentration of certain elements. From the spectrum recorded in the bed, a complete ultimate analysis, the percent ash content, and the heat content were determined without recourse to an external standard. Delayed gamma-ray analyses of the core were also made on the surface in the vicinity of the borehole in a fixed-geometry irradiation facility wing the detector in the borehole sonde. The concentrations of 10 elements were determined by this method on a coal split from the drill core. These experiments show that it is feasible to use a 252Cf- Ge(Li) borehole sonde as an aid in coal exploration.

Jan 1, 1979