Search Documents

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By U. Heuer, B. Rathmann

Many mining operations have gained an impressive expertise in trouble shooting and maintenance with their existing fleet over the years. Whether it is an in-house maintenance group or an external service group - most of the systems weak points are well known and can be corrected by maintenance personnel. As some of these issues get more and more serious each year, too much time is lost in unscheduled downtime, often taking hours to be repaired and to find the failure with obsolete diagnostic tools (Fig. 1.). Many of the breakdowns result from failures that cannot be detected in advance. The maintenance system is much more reactive than preventative. The state of the art of mining equipment today uses advanced, efficient, and reliable systems for electrical drives, control and diagnostics of the machines. The demand for highly sophisticated solutions on such mining equipment is well known. Mining operators need to ensure the highest level of productivity, lowest operating costs, least maintenance and highest reliability in a drive system. The paper will introduce you to the state of the art of drives technology for dragline (Fig. 2) and shovel mining equipment (Fig. 3).

Jan 1, 2007

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006

By S. Jeffress Williams

Continental shelf margins are dynamic sedimentary environments that contain important benthic habitats and support many functions such as navigation, national defense, cables, pipelines, trawling, and oil and gas and mineral extraction. Coastal margins also contain resources such as sand and gravel aggregates, which are becoming increasingly important for beach nourishment to mitigate coastal erosion and enhance recreation and to restore degraded coastal ecosystems. Existing geologic maps of the seafloor and sub-bottom sedimentary character, morphology, texture, composition, and other seafloor properties are not available for some regions, are out of date and not inclusive of the massive data collected during the past several decades, and are not in GIS-based digital formats. New geologic maps, based on unified and integrated national digital datasets, showing the sedimentary character of continental margins are critical tools for both research to better understanding the geologic history and processes of continental margins as well as the distribution of habitats and resources and for managing coastal-marine resources. The majority of existing seafloor maps are decades old and do not include recent data from mapping surveys, seabed sampling and observation carried out by federal agencies, universities and industry. Because continental margins are increasingly important, comprehensive and integrated databases are needed to produce GIS-based digital maps displaying information such as seafloor geology, sediment character, texture and distribution. To meet the need for a unified database of seafloor sedimentary character, the USGS is conducting the Marine Aggregate Resources and Processes project, a national assessment of marine sand and gravel with federal, state, and academic partners.

Jan 1, 2004

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

By G. Richards Gwinn

"Mica" is a group name for a number of orthosilicates of aluminum with magnesium, ferrous iron, and the alkalies. They are characterized by their high reflection and a basal cleavage so well developed that they can be split into exceedingly thin laminae, which are more or less tough, elastic, and transparent, according to variety. Barium, manganese, lithium, chromium, titanium, boron, and ferric iron occur in same varieties. Eight distinct species of true mica, which appear in the following table, are recognized by mineralogists, but only the first five are of commercial importance. [Species General Formula Muscovite H2KA13 (SiO4)3 Phlogopite [H,K, (MgF)]) Mg3A1 (Si04)3 Biotite (H,K)2(Mg,Fe)2(Al)Fe)2 (S104)3 Lepidolite K,Li Al(OH,F)2 Al (5103)3 Ros coalite H8K(Mg,Fe) (A1,V)4 (S103)12 Paragonite H2NaAl3(S104)3 Zinnwaldite (K)Li)3 FeAl3 Si5016(OH,F)2 Lepidomelene HK2F3IIIFe6III A13 (S104)9]

Jan 1, 1951

By S. Rupprecht, G. Rapson

Long blast hole drilling has been successfully implemented since the 1950s in caving operations, steeply dipping wide reefs and boxhole/raise developments worldwide. However, when applying long hole drilling to narrow tabular reefs, the challenges of achieving high economic drilling rates, combined with acceptable accuracy and appropriate powder factors have yet to be overcome. The focus in this paper is the selection, application and optimization of long hole drilling equipment at mining operations shallower than 2 000 meters. The drilling, blasting and cleaning operations have to be optimized as a process if maximum production at minimum per unit cost is to be achieved. For this to be possible, it is essential that the mine design and layout match the mining process being implemented. The critical parameters affecting the sustainable implementation of long hole drilling in stoping applications for platinum mines are improved safety and higher production rates compared to conventional methods. In terms of drilling, both top hammer and down-the hole hammer configurations have been considered. For economic drilling, the benefits of monitoring and optimizing performance (i.e. drill bit rotation, thrust, and percussive power) for specific rock types are discussed. While the drive is for longer, more accurate, smaller diameter holes to reduce drilling costs, the design of appropriate blast hole patterns and the corresponding charging and initiation systems is crucial for success. The effect of hole diameter and pattern on the powder factor, when comparing small diameter, shorter holes versus large diameter, longer holes, is a major factor in achieving good blasting results. Once appropriate drilling and blasting have been implemented, the cleaning process becomes a potentially critical operation to ensure the production, cost and safety goals are met. Hence, the blast hole pattern and charge have to be integrated for optimal fragmentation to suit the cleaning cycle for maximum production output. Providing that long blast hole drilling is applied as a process in a planned, committed and well-managed manner, the benefits in safety, production and cost over conventional methods should be achievable. However, if the implementation process is not planned and supported by all parties concerned, it will not be possible to succeed in the new operation. Hence, an implementation or roll-out plan of new technology is crucial for success.

Jan 1, 2004

By Claudio Toro, Alex Moyano, Rodrigo Díaz, Hugo Jara, Carlos Caballero, Pedro Morales, Leandro Guzmán

"During 2007, Codelco-Chile carried out industrial tests to validate the Continuous Converting Process in the Teniente Converter of the Codelco Norte smelter.For planning and starting up the tests, a predictive, analytical and dynamic model was developed to support operational decisions. The dynamic model was developed using the METSIM® platform and dynamic data exchange (DDE) to operate smoothly with MS Excel®. The main feature of this real-time model was the on/off-line ability to work and gather data from either the smelter’s PI system® or database, and simulate the operation with or without scheduled events and controls.The main model development aspects, which include thermodynamics, metallurgical and kinetic considerations, slag-type and on-line mass and heat balances of the process, as well as the successful validation of the model, are presented and discussed in the present paper."

Jan 1, 2009

By H. M. Wells

The influence of economics on the design of mine shaft systems by H, M. WEI.LS, Pr. Eng., M.Se. (Fellow) The purpose of this paper is to review some of the more important economic criteria that must be taken into account when planning the number, type, size, and distribution of the shafts, or shaft systems, required to exploit a block of payable ore. The postulated philosophy governing the selection of design parameters is that of optimization of the financial return per rand of venture capital employed for the project as a whole. While this criterion may not necessarily satisfy the investment objective under all circumstances (as, for instance, where risk limitation is important), it does serve to place the relative economic advantages and disadvantages of specific design features, which may sometimes be in opposition, into correct perspective with respect to the overall economics of the project under the prevailing economic climate at the time of the investigation.

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE ST. Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 12, 1918

By Richard N. Grigsby

INTRODUCTION The Chord property was acquired in 1975 from Roy Chord, an early prospector and miner of the area. He had staked numerous claims on the southern flank of the Black Hills in the early 19501s, and by the late 50’s, many small open pit and underground mines had been or were in operation. By the mid 1960's small tonnages of high-grade oxidized uranium ore had been mined from the property. Starting in 1975, Union Carbide conducted a series of exploration programs to determine the remaining economic potential. The previously mined areas were re-examined in order to define additional oxidized mineralization. Meanwhile, a wide-spaced drilling program was initiated to determine the potential for deeper unoxidized deposits. Through the exploration program of 1979, measured minable reserves in excess of two million pounds of contained uranium had been discovered. GEOLOGY The Edgemont District is located on the southern end of the Black Hills Uplift. A succession of pre-Cambrian to Cretaceous Formations is exposed within the core and across the flanks. The uranium host is the lower Cretaceous Inyan Kara Group which is divided into two formations, the Lakota and Fall River Formations (Figure 1). The basal Lakota Formation rests unconformably on the Jurassic Morrison Formation and consists of fluvial channel sandstones

Jan 1, 1983

By G. A. Irona

Solids injection into non-ferrous converters and furnaces is becoming increasingly important for concentrate injection, removal of impurities, and recycling of dusts and other waste materials. The fundamental design aspects of these technologies will be reviewed, including gas and particle trajectories, lance clogging, heat transfer, and mass transfer including reaction rates and mixing. The use of soda ash for removal of impurities such as antimony and selenium will be used as an example of versatility of powder injection processes.

Jan 1, 1993

By N. O. Taylor

THE failure, by swelling, of several cast aluminum-zinc, spiral, pump rods, used to circulate water in a constant-temperature bath, brought up the question as to whether the presence of tin in varying quantities would have any appreciable influence in controlling this action. Previous workers had found the same difficulty with aluminum-zinc alloys, due to their swelling in water or solutions of electrolyte^.^ It was known that pure aluminum was practically insoluble in concentrated sulfuric and nitric acids, presumably due to the formation of an oxidized film on the surface. Concentrated sulfuric acid had little or no effect on pure zinc and tin and concentrated hydrochloric acid would attack all three metals. These facts aroused curiosity as to the probable reaction of the ternary alloys of these metals, and tests were made to determine their resistivity to the action of common laboratory reagents. Samples, covering the entire range of the ternary series of aluminum, zinc and tin alloys, were made up from good grades of the commercial metals.2 The materials were melted, at as low temperatures as possible, in graphite crucibles in a gas-fired crucible furnace. Graphite crucibles were used in preference to clay, to prevent the absorption of silicon by the aluminum, as found by previous workers. The melted materials were stirred thoroughly with pine sticks in order to ensure complete mixing and the greatest possible freedom from oxidation, and were cast in sectional, iron molds giving bars % in. in diameter and 5 in. long.

Jan 1, 1927

By Yoshinao Kobayashi

he removal of oxygen from titanium and zirconium is important for use in application because it significantly affects the mechanical and physical properties such as ductility and toughness. However, thermodynamic properties of oxygen in molten titanium and zirconium have not been clarified and the effective deoxidation process of molten titanium and zirconium has not been established. In this study, the standard Gibbs energy of reaction of oxygen and yttrium in molten titanium and zirconium have been measured by a chemical equilibrium technique. Molten titanium, zirconium, and their alloys with aluminum were equilibrated with a Y2O3, A12O3, or Zr02 pellet in a cold crucible. The results are summarized as follows:

Jan 1, 2000

By J. S. Gardner, K. E. Houston, A. Campoli

INTRODUCTION Disposal of coal refuse is a costly and challenging problem facing the coal industry today. After the Martin County Coal Company slurry spill and the subsequent regulatory changes state and federal agencies are now beginning to require companies to justify new slurry impoundments. The authors have performed an analysis of different means of disposing of coal refuse for a major coal producing company located in the eastern Kentucky coalfields (the name of which will be withheld for the purpose of this paper). The company’s existing slurry impoundment is nearing its maximum permitted elevation and also an elevation where it may come in contact with abandoned underground workings. Due to the increased concern with underground mine works near slurry impoundments, additional consideration was given to raising the existing impoundment. Several other alternatives were evaluated, including but not limited to raising the existing impoundment, constructing a new slurry impoundment, constructing slurry cells, belt presses and others. This alternatives analysis was performed as part of a Section 404 permit for a valley fill and is currently being reviewed by the U. S. Army Corp of Engineers. All of the known possible alternatives were discussed in detail in the analysis. Due to the findings of the alternatives analysis, the company considers the engineered construction of the proposed impoundment to be the most favorable option of all the other alternatives evaluated, from both an economic and environmental standpoint. ALTERNATIVES EVALUATION FOR COALREFUSE/SLURRY DISPOSAL Background The company currently operates several deep mines and employ over 300 people and produces over 3.9 clean Mt/a (4 million stpy) of high quality, low sulfur coal. Currently, coarse refuse is belted to a valley fill, while, fine refuse is pumped to the existing impoundment. Coarse refuse is trucked to the existing impoundment as needed for construction purposes. The average recovery is approximately 50%; therefore, over 3.9 Mt/a (4 million stpy) of coal refuse must also be separated and placed.

Jan 1, 2003