Search Documents

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By U. K. Custred

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. This trend contrasts sharply with the reduced phosphate rock production levels of the 1966 - 1971 period. The natural consequence of this growing phosphate rock market is an evaluation of the variety of means whereby plant capacity can be most effectively increased. One approach toward increased plant production capacity is through large capacity flotation cells provided they can be successfully applied to the recovery of the relatively coarse product which is characteristic of the phosphate rock feed. This paper will summarize the results of a nine month evaluation test program, conducted at the Haynesworth Mine at Bradley, Florida in which the flotation circuit "specific capacity" (tons feed/ft.2 floor space) and "specific input power" (Hp/ton feed) were determined, and the feasibility of achieving economically acceptable concentrate grade and recovery levels was demonstrated, using large, high capacity, flotation cells.

Jan 1, 1974

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases. In the 1950's, the Chesapeake and Potomac Telephone Co. of West Virginia introduced a telephone set for use in explosive atmospheres that was designed around the philosophy of explosion containment. To contain an explosion within the telephone set required a 39-pound casing, which greatly limited portability. [ ] Both of these telephone sets required "pipe" or conduit, not a very practical item for a 100-squaremile coal mine. A common thread prevalent in the first 40 years of design and development is that the primary effort was placed on the telephone set. In the early 19701s, as work began on the design of modern communication systems for use in underground mine environments, the following requirements were established: 1. Must meet intrinsic safety standards .--This applies not only to coal mines, but to other explosive environments. 2. Must be compatible with the environment.--The system must with- stand dust, moisture, and corrosive conditions. 3. Must be rugged in structure.-- The system must withstand maintenance by 10-inch pliers and 4-pound hammers, as well as impact from a falling piece of roof. 4. Must be size-flexible.--Whatever is built must be sized for the small operator as well as the large companies. 5. Must be a total system in design.--The system must be intrinsically safe, including cable, power supply, and station set. 6. Must work with present telephone system.--The system should be compatible with aboveground communications already in place; it should not be the single cause of change in aboveground communications. 7. Value-added pricing.--The system should be reasonably priced so that savings created by its introduction will more than offset the installation cost.

Jan 1, 1984

Active geothermal fields show many of the characteristics seen in hydrothermal ore deposits but there are important differences as well. There are, for example, many differences in geology and chemistry between individual geothermal fields, even some nearby, and these include variations in host rock types (volcanic, sedimentary, plutonic and metamorphic), structures controlling fluid flow (normal, lateral, and, rarely, reverse faulting occur) and hydrological setting (valleys to elevated terrain).

Jan 1, 1986

The FSPE Award for Services to the Engineering Profession was awarded to Or Francis George Hill at a ceremony held in January of this year by the Federation of Societies of Professional Engineers. The following is an abridged version of the citation made by Professor A.N. Brown, President of FSPE, and of Or Hill?s reply. Achievements. It is indeed fitting that such a distinguished group of people have gathered on this special occasion to honour and pay tribute to Or Pinkey Hill

Jan 1, 1988

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By Lyman G. J

The volumetric distribution of valuable mineral, or phase, within a set of particles is called the liberation distribution. To optimise a mineral processing plant it is necessary to know the liberation distribution in most of the streams, especially those adjacent to separation devices. Possibly the most common method of analysing ore particles is to section sets of similarly-sized particles. However, the observed sections can appear liberated even if the particle is composite. This means that the 'apparent' liberation distribution can be very different to the 'actual' liberation distribution. This discrepancy is called stereological error. One must then somehow estimate the actual liberation distribution using the apparent liberation distribution. This problem is called the liberation distribution problem and its solution is the subject of this paper. The solution is based on a sorting algorithm which uses geometric probability equations. These equations are based on the assumption that sectioning is isotropic and uniform. Apart from these assumptions the equations are completely independent of particle shape or texture. The algorithm is verified by numerical simulation and experimental methods. For the numerical simulations the correspondence between the actual and estimated liberation distributions is excellent. For the experimental methods, the agreement is not as good and appears to be due to experimental errors.

Jan 1, 1995

Jan 1, 1952

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By Margaret R. Egan

The Bureau of Mines subjected three commercially available brands of transformer fluid to a series of combustion studies. The experiments were conducted in the intermediate-scale fire tunnel, which was designed to simulate environmental conditions in underground mines. The work was divided into three phases. In phase one, the brands were compared for gas production, smoke characteristics, and combustion yields. In phase two, the production constants of transformer fluids and other fuels were compared for the rate of formation of gas and smoke as a function of fire size. In phase three, several diameters of liquid-pool fires were compared in terms of fire size and burning rate. These transformer fluid measurements will be added to the existing coal and wood data that can be used as a basis of comparison for future studies of other mine combustibles. Further research into the combustion product emissions from combustible materials found in underground mines will lead to improved and realistic fire detection and suppression systems,

Jan 1, 1986

By A. H. Anderson

THE travelling grate coking process was developed by Shawinigan Chemicals, Limited, at their Shawinigan Falls plant. The first production unit went into operation a month prior to the outbreak of the war. Since then a substantial part of the coke used in the manufacture of calcium carbide has been produced by this process. In the following will be given a short account of the development work, a description of the process and the equipment, a discussion of the properties of the coke, the economics of the process and its future possibilities. EXPERIMENTAL WORK The carbide industry is a large consumer of coke, one ton of commercial carbide requiring for its production 1,200 lb. This coke must meet certain specifications in order to be acceptable. It should have a low ash content, preferably below 8 per cent, and the sulphur and phosphorus content must not be above specified limits. The size of the coke is also important. If it is too large it has to be crushed before it can be used in the furnaces, and if it is too fine it may have to be screened and briquetted. In addition, it must be dry. Although it was generally possible to purchase coke, including petroleum coke, and coke fines, in the quantities required, it became increasingly more difficult as time went on to obtain coke of a suitable quality at an attractive price. It was therefore natural for us to look to coal carbonization as a means of basing the supply of the fundamental raw material for carbide manufacture on something more solid than the shifting conditions of the coke market.

Jan 1, 1944

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By R. V. Ramani, J. Qin

"During the mining process, the insitu material is broken into different size ranges, from very, large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable. dust is associated with health and safety of the miners: The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper.. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined.The amount of respirable dust airborne is on the average only. 0.016% of the respirable dust generated. On the average, 61% of the total .airborne dust measured is in the respirable size range. The amount of respirable airborne' is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (<0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of 'the airborne propensity of respirable dusts in mine atmospheres.INTRODUCTIONMining is a sequential process of breaking, gathering, loading, and transporting the in-situ .materials.' In underground coal mines, duet in both the non-respirable and respirable size ranges is generated and entrained in every phase of the process. Even though large amounts of dust particles' adhere to run-of-mine coals, part of the dust generated becomes airborne (Cheng and Zukovich, 1973). Studies have shown that bit type affects the amount of dust generated'(Evans and Pomeroy, 1966; Kurth et al., 1975; Roepke et al., 1976; Stecklein et al., 1982; and Khair and 'Reddy, 1986). Deep cutting can reduce airborne dust generation (Black and Schmidt, 1977 arid, Black et 1978). Mechanical properties of. coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable. dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with' data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is'widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism of dust generation and the process by which the generated dust becomes airborne are complex and not yet completely understood coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism"

Jan 1, 1989

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

Jan 1, 1927

By Magnus Ek

After the installation of three new converters as part of the recent expansion of the Rönnskär smelter completed in 2000 work continues to further improve the converter operation. The converter upgrade led to an increase in blister copper taps from 150 tons per batch to more than 300 tons. The total cathode copper production increased from 130,000 tons in 1999 to 230,000 tons in 2001, the first year in full production. In recent years focus has been to improve operating practise, maximize the blowing time, extend the converter campaigns hence to reduce the specific brick consumption and improve the converter slag composition.

Jan 1, 2005

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Shannon Studden, Angela King, Allan Koski

Cliffs Natural Resources is an international mining and natural resources company with over 160 years of history. A member of the S&P 500 Index, the company is a major global iron ore producer and a significant producer of metallurgical coal. Throughout its history, employees have been the foundation of the company’s success, which has long embraced a focus on continuous business improvement.

Jan 1, 2014

By S McKnight, L Koroznikova, S Hall

Mineral sands represent an important new resource being developed in the Murray Basin, including parts of western Victoria. This paper will outline a simple methodology for mineral sands characterisation, developed as part of the AMIRA-managed project P777 æThe Development of Heavy Suspension Techniques for High Density Separations (Replacement of ClericiÆs Solution)Æ. This project is currently sponsored by three multinational mining companies (De Beers Consolidated Mines, Iluka Resources Limited and Rio Tinto Limited) and is developing an innovative laboratory mineral characterisation procedure that will allow the replacement of the currently employed highly-toxic chemicals.Mineral sand resources almost always contain more than one valuable (and relatively heavy) mineral. Titanium minerals are found with a large range of titanium contents, giving rise to density variation and often subjective mineralogical descriptions. Companies tend to rely on laboratory heavy liquid separation in the evaluation of samples arising from exploration, mining or metallurgical processes. Unfortunately, there are only a limited number of high density (æheavyÆ) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. However, beyond this value currently only organic liquids can be used. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used; however, this presents significant health and safety hazards. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0, hence æClericiÆs solutionÆ. For the characterisation of the heavy components of mineral sand deposits (eg anatase sg 3.9, rutile sg 4.2, ilmenite sg 4.4 û 4.7 and zircon sg 4.6 û 4.8) there is currently no heavy liquid alternative to ClericiÆs solution. ClericiÆs solution is highly toxic and testing is now conducted by very few laboratories worldwide with costs reflecting the chemical costs (though extensive efforts are made to recover and reuse the liquid, plus the requirement of its removal from the mineral samples), the infrastructure costs and health and safety regimes (eg blood testing of exposed staff, inventory management). A simple laboratory technique of density fractionation is being developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions, that can replace ClericiÆs solution in the evaluation of fine mineral sands samples (eg -250+150 microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 5.0 will be outlined and the comparison of results with ClericiÆs solution presented.

Jan 1, 2006