Search Documents

By Richard Turnbull

Maules Creek mine is an open cut coal near Boggabri in the Gunnedah Basin of New South Wales, Australia. The mine is currently operating at an annualised run rate of 9.5Mt of saleable coal. The plan is to ramp up production to 13Mtpa. Maules Creek has multiple seams each with varying depths; the inter-burden ranges from a few metres thick to greater than 30m (98ft). Due to this, Maules Creek mine is utilising truck shovel operations rather than a cast/dozer push operation.

Jan 1, 2018

By T. L. McCall

CHANGES in mining practices have evolved so quietly and unobtrusively that perhaps we scarcely appreciate how truly startling these changes are unless we cast our minds back so as to compare the past with the present. Such retrospection is, indeed, necessary when attempting to forecast the future, for it is only by carefully reviewing the past that we can hope to obtain an indication of what the future may hold in store. In this instance, it is not necessary to delve into the very early history of . coal mining, as our purpose will be served if the last three or four decades are reviewed, a period that is still fresh within the memory of many of us. These earlier days might be termed the selective period of mining, for at that time the coal resources of the world had not been tapped to anything like the extent they are at present and this condition enabled the owners and operators to exercise selective powers and only mine such seams of coal as could be most easily reached an worked at the lowest possible cost and which, at the same time, would suit the requirements of the market. Carrying this thought of selective mining still further, the miner, who was then an artisan skilled in all the branches of his calling, was able to select or discard such parts of the seam he was working that the co al sent out of the mine was acceptable to the consumer with just the barest minimum of preparation. Compare these conditions with the? conditions prevailing today, when coal seams of medium height, good quality, and readily accessible have been largely depleted and the operator has been compelled either to carry on his operations under much greater depths of cover where the coal is more costly to win, or else to work seams of lesser height or of poorer quality.

Jan 1, 1938

By S. C. Dhara

A process of solvent extraction and separation of platinum group metals (PGM) and gold using primary, secondary, tertiary, and quarternary organic amines has been briefly described. The effects of amine structures; the use of diluents; the principle of synergism and antisynergism in the mixed extractants; the oxidation states of metal ions are explained in the amine extraction process of precious metals.

Jan 1, 1984

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

By D. E. Cameron

"INTRODUCTION Grade control requirements for base and precious metal projects are an important input to both conceptual and feasibility mine plans. It’s the author’s experience that grade control input is insufficient at these critical stages. The few exceptions are a stimulus for this paper. A significant portion of CRC’s practice has involved assisting operations to solve grade control issues which were finally recognized as contributing to negative production variances. Even in operations perceived to be successful, deficiencies in grade control are often masked by measures taken by an operation to compensate a deficiency in one area with outperformance in another. The advantages in having a realistic and adequate grade control plan developed at an early project stage by a geologist(s) with considerable operations experience are manifold. It’s important for the geologist to prepare clear inputs into the mine plan backed by detailed supporting information in usable, flexible formats. When the decision is made to advance a project, the exploration team passes its model to a mine planner. The team doesn’t usually provide a detailed grade control plan with the block model, thus the planner tends to treat grade control as an activity to be rolled into a broader operating category. The consequences of highly compartmentalized mine planning can be severe in the long run. Once a plan is tabled, and especially once production begins, it is very difficult to improve grade control outside the fixed parameters of the operation. Major fixes tend to be costly in terms of time and dollars. Implementing needed changes to the grade control practices and culture in an established mine can present almost insurmountable difficulties. Hypothetical examples of grade control planning are presented to illustrate the author’s points. The diagrams are conceptual and schematic; any resemblance to actual deposits is coincidental. BEYOND 50¢/TON In more than a few cases, grade control cost is buried in a subcategory of mining cost with little more consideration than a plugged number. It is possible to do a word search in 43-101 Technical Reports on advanced projects and without finding reference to “ore control” or “grade control”. The idea is to reach the orebody by the shortest and least expensive means, achieving production and investor payback at the earliest possible occasion. This entails a low stripping ratio pit or a decline ramp with sills on ore to prepare the first stopes. The processes to achieve the target production, one of which is grade control, will fit into this framework. After all, there is a block model and the planner can see the grade and tons in each block. The exploration geologist whose responsibility was to bring a large percentage of the deposit into mineral resource owns the model and has released it to planning. Now comes the planning stage. Mine geologists haven’t been hired yet and they will be phased in with production. What could go wrong? Larger companies may have the geologists with operating depth who will be inserted into the mine planning discussions, but it’s not a given. Junior companies must often delegate the conceptual and detailed planning tasks to consultant groups. Is a senior-level grade control review part of the scope of work for the mine planning? If a good grade control plan is in place before the mine geology team is staffed, a key element of success is assured."

Jan 1, 2018

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By Hayward B. Oblad, Gary F. Meenan

Two optoelectronic detectors were developed by CONSOL R&D for fine coal processing applications. One sensing device is used to estimate the amount of fine coal in the solids fraction of the froth flotation tailings slurry. The other probe, based on similar technology, is capable of measuring sol ids concentrations as high as 10 weight percent in fine coal slurry streams. These patented optoelectronic sensors are installed in several CONSOL coal preparation plants and are an integral part of the fine-coal control systems.

Jan 1, 1993

Jan 1, 1970

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract I for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 11, 1976

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

Southeast Alaska's mining industry has come to life after nearly 50 years of relative dormancy. Commencement of operations of the Greens Creek Mine in 1989 marked a turning point in the industry as the first large scale mining operation in the region since closure of the Alaska-Juneau Mine in 1944. The Greens Creek Mine is now the nation's largest silver producer. Other large scale mining projects are now on the drawing board, including development of the Kensington Mine and reopening the Alaska-Juneau Mine, which could become North America's largest underground gold mine. The region's mining industry includes more than these large scale projects, however. For example, a significant level of mineral exploration occurs each summer in Southeast Alaska. In addition, mining operations in British Columbia and Yukon Territory are generating jobs and income in Southeast Alaska.

Jan 1, 1992

By Chas Kemsley

NO. 6 shaft at Dome Mines, Limited, is an internal shaft going down vertically from the sixteenth, or 2,000-ft., level to the twenty-ninth, or 4,000-ft., level, with loading station and sump below this. It is located approximately 4,600 feet east of No. 3 shaft, the latter being Dome's main shaft through which ail ore, men, and material are handled. The decision to sink this shaft was made in May, 1935, and work was commenced almost immediately. To reach the site of the new shaft, 3,100 feet of cross-cutting, and 1,400 feet of slashing to widen existing cross-cuts, was necessary. On account of the long haul and the large amount of material to be handled, trolley haulage was decided upon and installed as soon as possible to facilitate the removal of waste rock from the crosscut and other necessary excavations. Figure 1 shows a cross-section of the cross cut and the manner in which the trolley wire is supported and guarded. For hanging each individual cross-piece, two holes are drilled into the roof and filled with snug-fitting wooden plugs. Into these, %-in. ragged hanger bolts arc driven by means of a stoper. The bolts are of various lengths to allow for irregularities in the face of the rock, and they have sufficient thread to permit several inches of adjustment for proper alignment of the cross-pieces. These hangers are spaced at 8-ft. intervals except at the curves, where 5-ft. spacing is used. A 2 in. by 6 in. cedar plank is fastened to the cross-pieces directly over the centre of the track. To this the trolley-wire supports are bolted, and 1 in. by 10 in. cedar boards are nailed on each side to act as guards. Two power-supply cables, one telephone cable, and one .Y2-in. conduit lighting circuit are also supported on the trolley-wire hangers, as shown in Figure 1. A 20-in. ventilating pipe and a 10-in. air line are placed as shown, thus acting as a guard to prevent workmen from walking on the track.

Jan 1, 1938

The Sandvik Group (Sandvik AB), headquartered in Sandviken, Sweden, continues to expand its worldwide operations growth. After recent acquisitions, including Tamrock, headquartered in Tampere, Finland, the company now has annual sales of more than US$5 billion (SEK 40 billion). With the acquisition of Tamrock, Sandvik has further increased its interests in the mining industry. Sandvik Rock Tools, a familiar name in the mining industry, is one of the world's leading suppliers of rock-drilling tools. And Tamrock is one of the world's leading suppliers of drilling machinery, loaders and equipment for rock-excavation operations. Sandvik believes that the two companies combined offer customers "maximum productivity through total system solutions, including machinery, service and tools." In 1997, Tamrock posted sales of US$940 million (SEK 7.5 billion). In addition to its expertise in drilling tools and equipment, Sandvik is supported by its collective resources in specialty steel and cemented carbide. These resources include extensive research and development capabilities, with annual investments in R&D now at about US$150 million. As a result of the R&D programs, internal expansion and acquisitions, the company has nearly doubled in size during the past four years. From 1994 to 1997, nearly US$1 billion was invested in internal growth and another US$825 million has gone towards acquisitions. Return on net assets is now 22% annually. In addition to Tamrock, acquisitions of interest to the mining community include Drillmaster Inc., Houston, TX. The acquisition of Drillmaster (by Sandvik Rock Tools) has further strengthened Sandvik's position in down-the-hole drilling tools. Other major recent acquisitions by Sandvik include Kanthal, a Swedish manu¬facturer of metal and ceramic-resistant materials for electric heating furnaces, household appliances and elec¬tronics, and Precision Twist Drill, Crystal Lake, IL, one of the leading producers of high-speed cutting tools. With more than 38,000 employees worldwide, the Sandvik Group is divided into six separate business areas. Each area is responsible for its own R&D, production and sales: ? Sandvik Mining and Construction. Including Tamrock and Sandvik Rock Tools, this business area boasts of offering the most comprehensive range of "rock-working" products. These include drilling rigs, loaders, rock-excavation equipment and rock drilling tools. ? Sandvik Specialty Steel. This area includes Sandvik Steel and Kanthal, manufacturers of stainless steel tube, strip wire and bar, as well as high-alloy steel and specialty metals. ? Sandvik Tooling. This business area consists of tools and tooling for metalworking applications. Sandvik Coromant is a market leader in the development, manufacture and marketing of tools using cemented carbide, ceramics and extremely hard materials, such as diamond and cubic nitrite. CTT Tools is the world's largest manufacturer of high-speed steel tools and is now expanding operations into solid cemented-carbide tools. ? Sandvik Hard Materials. This segment produces a full range of "hard materials," ranging from cemented carbide to diamond. This area manufactures and markets a full range of cemented carbide blanks for tool manufacturers, as well as components and rolls. ? Sandvik Saws and Tools. This business area manufactures high-quality handsaws and metal saw blades, as well as hand tools ranging from wrenches to chains for logging machines. ? Sandvik Process Systems. This segment manufactures steel belts, process systems and automatic sorting systems for the chemical

Jan 1, 1998

By Gregg R. Bierei

Arch of Illinois is a mining complex comprised of two surface and two underground mines located in Perry County, in southern Illinois. The company a division of Apogee Coal Co. of St. Louis, MO. Arch of Illinois' two surface mines, the Captain and Horse Creek Mines, use large stripping shovels and cross-pit bucketwheel excavators to remove overburden from three seams of coal, the Herrin No. 6, Harrisburg No. 5 and Danville No. 7. All are considered high sulfur reserves. The two underground operations are managed by Arch of Illinois. They are the Kathleen Mine and the newly constructed Conant Mine, which began production in 1991. Both underground mines are continuous miner operations. They mine the No. 6 coal, which is about 1.8 m to 2.1 m (6 to 7 ft) thick. All coal is currently transported by truck to a central preparation plant located at the Captain Mine. This preparation plant produces 27 kt/d (30,000 stpd) of clean coal. Production in 1992 reached 5.9 Mt (6.5 million st) of saleable coal. Of that, about 66% or 4 Mt (4.4 million st) are produced by the surface mines and the rest the by under ground operations. Change is in the wind for Arch of Illinois. In 1988, 100% of all production (6.2 Mt or 6.9 million st) came from surface operations. By 1995, only 38% of production is scheduled from surface mines. And by the year 2000, 100% of production will from underground mining methods. Dwindling low ratio reserves, compounded by increasing environmental and land acquisition costs, coupled with more efficient underground mining equipment, have started an evolutionary trend toward development of underground reserves. For Arch of Illinois to maintain profitability of remaining surface reserves and to compete effectively mining underground, it must improve efficiency, productivity and cost reductions. These efforts are essential for maximizing current surface reserves and to ensure a continued existence in the presence of clean air legislation and the softening of the high sulfur coal market.

Jan 1, 1993

By Susasn Leiter

THAT oxygen in copper has been a source of trouble is well known and that that trouble has been real in the commercial world has been shown by Fuller.1 Moore and Beckinsale's paper2 at the annual meeting of the Institute of Metals in London, 1921, called forth considerable discussion. Prof. T. Turner expressed the opinion that it was not necessary to have cuprous oxide present in sufficiently large quantities to form either globules or seams in order to produce a bad effect if the copper were gassed. This brought up the question of the solubility of oxygen in copper and the authors desired to know whether there were any evidence of such solubility, because their experience was that whenever there was any oxygen in copper it was present in the form of free cuprous oxide, .which was practically always in the form of globules. Later Hanson, Marryat, and Ford3 stated that for all practical purposes cuprous oxide may be regarded as insoluble in copper. However, they found particles of the eutectic to coalesce to form much larger particles. They suggested that cuprous oxide was actually slightly soluble in copper, for it was diffi-cult otherwise to understand the mechanism by which such coalescence could take place. W. E. Ruder, in discussing that paper, said that his experiments had led him to conclude that a slight solubility must exist to allow for the ready coalescence of oxide particles, but conductivity tests convinced him that that solubility was very small. Nevertheless, there appeared to be a state of admixture of oxide with copper that closely resembled a colloidal mixture which at first was mistaken for a true solution and which usually existed at the grain boundaries.

Jan 2, 1926

By Cullen JF

Australia has a large resource of manganese at BHP's Groote Eylandt mine which has been progressively developed over the last two decades. While much of the product is marketed internationally to the iron and steel industry, substantial quantities are processed in Australia at the Company's ferro alloy works in Tasmania. In addition, small but increasing quantities of ore are being consumed by the non-metallurgical industry. Fluctuating fortunes in the steel industry produce similar trends in the marketing of manganese. The increasing cost of freight and power together with strict environmental control is further affecting the market balance. Mine operators are expanding into the alloy making field. Reduction in usage in less developed countries is occurring.

Jan 1, 1982

By R. H. Merrill, D. W. Wisecarver

The paper "Design of Surface and Near-Surface Construction in Rock" by Deere, Hendron, Jr., Patton, and Cording discloses a principal difference between civil and mining engineering as applied to openings in rock. Generally, the civil engineer considers an opening as an asset, where a mining engineer finds that most of his openings are a liability. The openings, or rock surfaces, treated in the paper by Deere and coauthors are designed for lasting stability and the foundations for dams, the diversion tunnels, abutments, and surface excavations are expected to be stable for long periods or provide continuous access and other useful purposes. Except for those openings used for the transportation of men, materials, ore, and for ventilation, the mining engineer finds that his underground openings serve no useful purpose once the mineralized rock has been removed. Usually, these openings create problems such as reduced ventilation efficiency, added requirements for scaling, sealing, and other tasks necessary to maintain or isolate the openings. The surface openings and mine plants present another liability to the mining engineer. After the product has been removed from the earth, the abandoned pits or strips, tailing ponds, dumps, and buildings sometimes become hazardous, unsightly, or occupy surface areas that could be used for other purposes. As a general rule, the various disciplines involved in rock mechanics have different objectives and uses for openings; however, the basic concepts regarding the design or control of openings in rock are similar for each discipline. The review by Deere and his coauthors contains examples of the duplications in this technology, and, in particular, the common approaches used by civil and mining engineers. Therefore, both the review paper and this report consider the problems that are common to most of

Jan 1, 1967

By E. D. Gardner

VICTOR G. HILLS, Denver, Colo. (communication to the Secretary*).¬If anyone advocates the abolition of the antecedent mineral discovery requirement for the purpose of making it easier to secure title to public land, I hasten to say that I am not of that number. I am in Hearty accord with all that Mr. Gardner has to say in regard to easy patenting as a handicap to small camps, and that in general it acts to retard the mining industry. And the following sentences I want to repeat in order to emphasize and endorse them, "None of the writers on this subject seem to have taken into consideration the effect amending the law pertaining to mineral discovery will have upon the Government's administration of the public land. It must be borne in mind that this land belongs absolutely to the people of the United States as a whole, and their interest must be considered. It is not a no-man's land, as some people would appear to believe." However, I believe that the discovery prerequisite should be abolished, because it fails to effect the protection for which it was designed, and I look for other provisions that will better serve the purpose. We propose to abolish the law of apex not because the theory is objectionable but because the question of physical fact gives rise to never ending litigation. Now the design of antecedent mineral discovery is good; the court rulings are unobjectionable; but when it comes to the physical fact this requirement is second only to the apex law as a healthy litigation breeder. The only circumstance that has prevented the pre-discovery lawsuits from becoming as famous and as: expensive as the apex

Jan 12, 1916

By Michael G. Zabetakis

Vaporization of a solvent into an airstream at temperatures above the flash point of the solvent is hazardous if vapor is liberated at a rate that is sufficient to produce a flammable mixture. In may operations, the formation of such a mixture is prevented by rapid diluton of the vapors with air. The minimum air requirements for the dilution process are determined by the composition of the lower limit mixture at the temperature and pressure of interest. Because limits of flammability cannot always be calculated with sufficient accuracy for a proposed operation, they .rust often be determined experimentally. The present Bureau of Mines investigation was prompted by an application in which the lower limits of flammability of a number of solvent mixtures were required over a range of temperatures at atmospheric pressure. These limits were to be used along with available solvent-vaporization-rate data to establish minimum airflow rates needed to prevent the formation of flammable mixtures in an industrial process. Lower limits of flammability were determined for a number of mixtures containing methyl ethyl ketone, tetrahydrofuran, toluene, ethyl alcohol, and ethyl acetate in dry air-at atmospheric pressure and temperatures between 16° and 200° C. The experimental values were found to be in good agreement at with those predicted by Le Chatelier's law; variations with temperature were in fair agreement with those predicted by a modified Burgess-Wheeler law.

Jan 1, 1962