Search Documents

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By S. A. Braley

DRAINAGE water from coal mines is probably the most serious water pollution problem today, varying in importance according to location of the mines and geological structure. Drainage may be either acid or alkaline in character. Acid discharge, the most severely detrimental to a stream, is caused by natural oxidation of the sulfuritic material (FeS2) in the strata associated with the coal seam. Since the acid is the result of a natural reaction the acid water differs because it does not cease with abandonment of the mining operations. There is no known economical method of neutralizing acid mine water or any practical method to prevent oxidation of exposed pyrite. Since production of acid from a mine does not stop when mining stops, the total quantity produced depends entirely upon the excavated areas. The increasing volume of acid water in manv mines has greatly increased operating costs. Pumping is expensive and acid mine waters are destructive of all equipment, especially metals in pumps and piping, and necessitate the use of corrosion-resistant materials. Discharge of the acid mine drainage into streams neutralizes their normal alkalinity, causes them to become acid, and produces an environment unfavorable for aquatic life and unsuited for industrial or domestic use without costly treatment. Mine drainages vary in percentage composition over wide limits, although the usual dissolved substances are ferrous and ferric iron, aluminum, calcium and magnesium sulfates, and lesser amounts of sodium, potassium and manganese sulfates and chlorides. Some alkaline discharges may contain heavy concentrations of iron as iron bicarbonate. These waters may produce iron hydroxide deposits in the receiving stream but do not cause it to become acid. In the extensive literature on acid mine water there appears to be a great deal of confusion about the importance of various components and the methods for their determination. In many instances faulty conclusions have been drawn from use of unsuitable methods of analysis. It is desirable that the factors and terms used in evaluation of analyses of mine waters should be so clearly defined that any interested person could properly appraise any analytical report. Some analysts report complete chemical analyses of mine waters and neglect to record drainage volumes. Others report only a minimum of analytical data after taking no precautions to preserve the original composition of the water during the time elapsing between collection and analysis. Some use methods of analysis intended for so-called pure waters of the potable and boiler water classes. These methods are not applicable to highly buffered waters such as mine water. Probably the most common criteria for evaluation are pH, free acidity, or acidity or alkalinity to methyl orange or methyl red, total acidity or acidity to hot phenol-phthalein, and the sulfate content. If these determinations are made on carelessly collected samples after a few days to weeks standing in warm rooms, they do not in any way represent the character of the water flowing from the mines. It is hoped that a brief discussion of the fundamental value of some of these factors may lead to a bettqr understanding of the need for more careful evaluation of mine water discharges. The term pH is one used by chemists to express relative acidity or alkalinity in terms of concentration of effective hydrogen ion in a solution. It is defined as the negative logarithm of the hydrogen ion concentration or activity in equivalents per liter. pH = logarithm A neutral solution, which is one containing the same number of hydrogen and hydroxyl ions, has a pH of 7. As the hydrogen ions increase and the solution becomes more acid, the pH decreases toward zero; and as the hydroxyl ions increase and the solution becomes more alkaline, the pH approaches 14. When dissolved in water to a dilute solution acids like sulfuric and hydrochloric, commonly known as strong acids, ionize completely, and the pH or hydrogen ion concentration varies with molar concentration of the dissolved acid. However, in high concentrations of such acids, the pH or hydrogen ion concentration is less than the acid concentration because the acid does not completely ionize. In only very dilute solutions does the pH represent the total amount of acid that can be neutralized by an alkali. All ionization reactions are equilibrium reactions. If other chemicals are added to the solution of an acid and the added chemical produces an ion that is the same as one of the ions of the acid, the degree of ionization of the acid is altered and the pH changes to some value that represents the active hydrogen ion of the new solution. Thus if iron sulfate is added to a solution of sulfuric acid the pH increases, since the common sulfate ion suppresses the degree of ionization of the sulfuric acid and decreases the effective hydrogen ion. However, the total acidity of the solution is increased. There are two salts composed of iron and sulfate— ferrous and ferric sulfate. In these salts there is no hydrogen ion that can ionize to give an acid solution, but when they are dissolved in water, the pH is less than 7 and the solution becomes acid. This is caused by a reaction known as hydrolysis and is represented by the equations FeSO4 + 2H2O ? Fe(OH)2 + 2H + SO,: or Fe,(SO,)3 + 6H2O ? 2Fe(OH)3 + 6H+ + 3504 A solution with a total acidity of 5000 ppm according to the first equation will have a pH of 4.40 but one with an acidity of 75 ppm, according to the sec-

Jan 1, 1958

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

The epithermal silver-gold Red Rock Deposit is hosted in the Late Permian inter- mediate to silicic composition Drake Volcanics of New England, N.S.W. This deposit represents one of the few low sulfur epithermal precious metal systems in eastern Australia, and differ! from epithermal models in that the hydrotherma: system which produced mineralization was active in a shallow water marine environment. The Red Rock Deposit has a resource of 180,000 tonnes of 66g/t Ag and 0.9 g/t Au, and a Ag:Au ratio of 70:1. Mineralization is largely associated with hydrothermal brecciation, and occurs as disseminations, vein stockworks, and struc- turally controlled lodes. Ore minerals comprise acanthite (argentite), electrum, native Ag, Ag- sulfosalts and base metal sulfides, Alteration minerals associated with ore are quartz, cal- cite, adularia, pyrite, illite, illite-mont- morillonite, chlorite and sphene (leucoxene). Illitic and propylitic alteration zones sur- round the hydrothermal breccia. Bulk rock analyses indicate that alteration is character- ized by the addition of Si, K, Fe, Mg and the loss of Na and Ca. Ore was deposited from a boiling fluid in a temperature range of 222- 295¦C, and of 0.5-7 wt. Z NaCl equivalent sal- inity. An upper hydrostatic depth limit of about 800 m is implied for the boiling fluid ii an open vein. Sulfur isotopes indicate a mag- matic sulfur source, and oxygen isotopes imply a predominantly marine ore fluid. Modern analogs of the submarine hydrothermal system that formed the Red Rock Deposit occur in the Taupo Zone, New Zealand, and southern Kyushu, Japan.

Jan 1, 1987

By Derek V. Ellis

This article is a summary, with documentation and references, of recent global developments in identifying environmental issues affecting the marine mining industry. It is recognised that marine mining for various products occurs at various depths from shallow water (e.g. aggregate and diamond mining) potentially to great depths (e.g. metalliferous muds, and manganese crusts and nodules). Nevertheless there are environmental issues in common, even though the options for resolutions will vary greatly. The point of this review is to identify the issues, so that where site-specific resolutions are considered, it is possible to draw on experience with the issues elsewhere. Related mining issues, e.g. tailings effluent quality, orebody geochemistry, are mentioned where relevant but are not detailed in this article, although obviously they are a part of there solutions to the environmental issues. The environmental issues and their resolutions are important - on the basis of the ethic of not creating more impact than is inevitable, and the long-term financial and social costs at a mine-site of not getting the resolutions right.

Jan 1, 2000

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

By P. J. M. van Heteren

The flotation system is usually distinguished from other physical chemical systems by the importance of interactions at the solid-liquid and solid-gas interfaces. In recent years, numerous quantitative studies have been made of the distribution of common collectors between the solid and aqueous solution phase. Although in flotation the main emphasis is placed on the adsorption process, chemical reactions will also take place in the bulk solution phase, These side reactions are often undesirable and will contribute towards the complex behavior of many a flotation system In sulfide flotation, the precipitation of insoluble base metal xanthates is a well-known phenomenon although the conditions under which the precipitation reaction will proceed and the magnitude of the solubility products are not known with accuracy. A knowledge of the solubility of these xanthate salts will not only be of value in flotation research, but the mill operator might be interested in knowing whether precipitation of metal xanthate can be controlled or completely prevented in the flotation circuit thereby reducing reagent consumption, For these various reasons the solubility of lead, copper, zinc, and silver ethyl xanthate was determined. The experimental techniques and results will be discussed in this paper.

Jan 1, 1958

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By J. Duncan Wilkins

Introduction In difficult times such as these, there is a strong reaction to the current way of doing things. Typical reactions that we have all heard are "There has to be a better way," "We're pricing ourselves out of business," "We have to improve our productivity," and "We have to have more cooperation," between union and management and employees and management. All of these comments have at their roots one common factor - getting the maximum amount for your dollar. The other factor inherent in these statements is productivity. I have not yet met a person in our industry who has not expressed the opinion that we should, and that we can, improve our productivity. Reducing Labor Costs In light of these factors I suspect we have all spent a fair amount of time examining our labor costs. For some of us, labor costs are a high proportion of our total cost of doing business. To alleviate the impact of these costs, we have generally done four things. We have reduced our number of employees, shut down operations for appropriate periods, sought concessions from union employees, and placed freezes on wages, salaries, and other benefits on nonunion employees. These approaches have been made to improve current shortfalls in our cash positions - to tide us over, as it were - or to provide us with a chance for survival. These are short-term measures that help to bring immediate relief, but can pose significant problems (or challenges), for the longer term. For instance, what do we do when times improve? How much do things have to improve before we do anything? By seeking concessions from unions in bad times, what do we do when unions come to us in good times? It is a rather sad and critical fact that we have grown too fat during the good times and too thin during the bad. In the first case, we have failed to optimize our earnings. In the second, we have cut ourselves too far. Consequently, when good or better times have arrived, we have had to bulk up our requirements to meet production commitments. In mining, for example, when times become tough, we tend to reduce our development plans so that when times improve we have to really "sock it to 'em," so that we can maintain productive capacities. We should plan ahead a little more to reduce the amplitude of our cyclical wavelength, so that in good times profits are optimized and in bad time we are better able to take the strain. Of course, forecasting cycles is not a refined art, but if we properly control our work force levels and costs at all times, and therefore optimize our productivity, we would be more able to withstand the problems we face today. Unfortunately, it appears that it takes bad times to bring us to a realistic appraisal of our way of managing our businesses. Labor Practices Not all of the problems now faced are due to low metal prices. Inflation has played a major role in bringing costs to a frightening level. Trade unions alone can not be blamed for high inflation levels over the past several years, popular though that notion is. Contract negotiations, after all, require two parties. Indeed, our current levels of labor cost are due to two factors: • We have felt obliged to keep our employees whole, relative to the cost of living. • We have felt obliged to maintain our competitive position relative to our peers, in order to maintain our ability to attract and retain a skilled, efficient work force. In the first case, our felt obligation has been applied without due recognition of the factor of performance, either in individuals or groups. Average, even mediocre performers, have been amply rewarded for their average work and mediocrity, while the good performers, no doubt receiving more for their good work and effort, have not perhaps appreciated the slight premium for their effectiveness. The rather predictable result of this practice has been that the average and mediocre stay that way (why change?), while some (certainly not all) of the good performers have said "It's not worth it," and slipped into the warm, cosy pool of the average and mediocre. In the second case, that of maintaining competitiveness with other companies' employees, we have compounded an already serious problem of lack of skilled tradesmen by paying higher and higher prices for the existing pool to maintain comparability without improving the flow of more skilled people through sound and sufficient training programs. We have the rather dubious pleasure of paying more and more for the same problems. Compensation is either mutually agreed, as with unions, or it is unilaterally applied, as with nonunion employees. Generally, there is more flexibility available to the employer when dealing with nonunionized groups than there is with unionized groups. Sometimes that flexibility has not been used well, most often be-

Jan 11, 1983

By H. Helmstaedt, P. Thurston, R. Harrap

"Evolution of the continental lithosphere over Earth’s 4.6 billion year history is one of the fundamental questions of geoscience. Much of the Earth’s present-day continental crust formed during the first 2 billion years, the Archean eon, of the planet’s lifetime and thus, Archean processes of lithospheric formation must be studied in order to address this question. Until recently, the processes of Archean lithospheric evolution were thought to be fundamentally different from present-day plate tectonic processes. However, subsequent evidence suggests that the growth of Archean continents may be explained in terms of modern tectonic accretionary tectonics similar to those presently operating in the southwest Pacific region. The evidence supporting this hypothesis was compiled largely by Canadian geoscientists working in the Superior Province of the Canadian Shield in northwestern Ontario, over the past 15 years. Study of Archean rocks is also economically important because the Archean rocks of the world, although comprising only a relatively small fraction of the exposed continental crust, contain much of the world’s mineral wealth, including more than half of the world’s gold, as well as significant base metal reserves. Furthermore, the vast majority of primary economic diamond deposits are derived from the lithospheric roots beneath Archean cratons.The LITHOPROBE Western Superior Transect is located within the western part of the Superior Province in northwestern Ontario (Fig. 1). The Superior Province is the largest and best exposed Archean crustal block in the world and forms the nucleus of the North American continent. The internal structure of the Superior Province records a history of the processes that formed the earliest lithospheric elements of the Earth into cratons, thus providing an ideal laboratory for investigating early crustal evolution. The Western Superior Province is characterized by a regional pattern of alternating, 100 km to 200 km wide geological belts (Fig. 2). The observed geologic relationships between and within these subprovinces have been explained in terms of a modern tectonic model of terrane accretion. Oceanic floor, volcanic island arcs, oceanic sediments and continental fragments were accreted successively from north to south against the southern margin of a cratonic nucleus (North Caribou terrane, Fig. 2) which grew steadily in size with the arrival of new terranes through geologic time. If this model is correct, it suggests that the tectonic processes operating today have been active without major variation over the past 3 billion years."

Jan 1, 1998

By G. J. McDougall, M. J. Nicol, O. L. Wellington, R. G. Copperthwaites, R. D. Hancock

X-ray photoelectron spectroscopy showed that the adsorption of gold cyanide on carbon in the presence or absence of electrolytes and acids proceeds by the same mechanism. Although the identity of the gold cyanide adsorbate is not known, the mechanism appears to have an initial adsorption stage that involves the adsorption of an ion pair: Mn+[Au(CN)-2]n where Mn+ is a metal ion (for example Na+, K+ and Ca2+) that has a lower solubility than the Au(CN)-2 anion in the adsorption medium, followed by a reduction step in which either a sub-stoichiometric Au(CN)x surface species or a cluster-type compound of gold is formed.

Jan 1, 1980

By G. A. Kosick, G. S. Dobby

"This paper presents the principles and application of a recently developed control system for flotation columns and column circuits. The control system uses triple pressure sensors to directly sense zone densities and level, and to help in characterizing the operating behaviour of individual columns. A complete expert system development tool is incorporated within the system to provide the facility for full operator training, an on-line help facility, and a means for incorporating the column behavioural patterns into decision making rules. The system is configurable to any number of columns and can be run in either supervisory mode or direct control through Minnovex PIO software. Additional process signals can be interfaced with the system if desired. Operating experience with the control system on the Minnovex column flotation pilot plant is described.I: INTRODUCTIONColumn flotation cells have been more difficult to control and are more sensitive to circuit changes than conventional mechanical flotation cells. This susceptibility encouraged investigation into various types of control strategies ranging from inexpensive single pressure measurements for level control, to highly instrumented and expensive systems using a variety of control methods.Flotation operators, in many cases, do not understand the column control philosophy or have not been trained to deal with this new type of cell. Some operators have subsequently absolved themselves of the column operating responsibility. Some column cells, for example, have run for hours with slurry pouring over the top or no froth coming off at all.ColumnEX is a column flotation control system which was developed from the viewpoint of an operating shift foreman who wishes to:1. control the column or column circuit through a genuine understanding of what is happening inside the columns, and2. to share this knowledge with his flotation operators and be available to guide them through times of circuit upsets."

Jan 1, 1990

The arbitration process, and its drawbacks: Any time you have taken part in a major arbitration, and the decision, when it comes out, is not what you thought it would be (which is bound to happen occasionally), the normal reaction is something like æthe arbitrator got it wrongÆ. Again normally, when you have cooled down a bit, and you look in more detail at the decision, you can see, probably, æwhere he got it wrongÆ (it is only male arbitrators who get it wrong). Ultimately, when reason prevails, and you reflect on it, you can see that what really happened was that you failed to get the arbitrator to see what you were getting at in the point or points concerned. This is doubly frustrating, when you consider what has been involved in getting to this point, having been through it all at least twice. An alternative to this process may be the dispute review board.

Jan 1, 1999

By Birger Schmidt

INTRODUCTION Conceptual design of the first Exploratory Shaft (ES-I) for the Nuclear Waste Repository in Basalt (NWRB) began in July 1981; detailed design began in February 1982, and was largely completed by December (RKE/PB, 1983). The intent was to begin shaft construction by January 1983. The site had been prepared at that time, a construction manager selected and on board, the starter hole excavated and lined, and steel casings were under procurement. Government policy changed, however, and construction was halted before the drill rig started turning. Construction is now planned to begin in 1988. ES-I is a part of the site characterization program for the NWRB. The shaft will be used to develop production data and related information relative to drilling shafts at the site near Richland, WA, and to provide access to the repository horizon for site characterization and testing. The early program called for one shaft and some 330 m (1000 ft) of drifting. The program has since expanded to include a second shaft (ES-II) and more extensive drifting and testing. Currently, both shafts are planned to be 1.8 m (6 ft) in finished diameter, but studies are underway to determine if the second shaft should be larger. The drilling method was selected for shaft construction primarily because it offered a significantly shorter construction period than conventional shaft sinking using freezing and grouting. The finished drilled shaft will be lined with a continuous steel lining. Personnel are safer during construction with a drilled shaft than with a conventionally sunk shaft. The drilling method

Jan 1, 1987

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

By P. M. Hedley

GOLD mining in Nova Scotia, as in any other gold district, has its own peculiar problems. Being in close proximity to excellent roads and to railways, and being blessed with good labour, the majority of gold mines in the Province find their paramount trouble is geological, namely, ore finding. After six years of continuous mining at Goldenville, the staff of Guysborough Mines, Limited, has collected many facts, has come to some definite conclusions, and has made a lot of guesses, some good and some bad. It is the purpose of this paper to set down such information as we have been able to gain in the hope that it may prove useful to other operators, present and future, faced with similar problems. What may be true of one Nova Scotian mine will not necessarily be true of another, so that the observations that follow should be considered as primarily applicable to Goldenville. Stated facts, conclusions, and theories are the result of the combined thought and effort of Head Office officials, of members of the Provincial and Federal Departments of Mines, and of members of the mine staff, past and present. Grateful acknowledgment is made to all.

Jan 1, 1941

By E. C. Pechin

The attention of the members of the Institute of Mining Engineers is asked to a description of the minerals of Southwestern Pennsylvania, as representing the minerals of an enormous area, stretching continuotisly, with local variations, along the western slopes, and at the base of the Alleghany Mountains, through Western Pennsylvania, West Virginia, and Kentucky, and destined to play no mean part in the future of the iron trade of the country. The particular locality is at and near Donbar, in Fayette County, where the most careful examinations and extensive developments have been made. The deep gorges cut by the Youghiogheny and Monongahela Rivers, in their passage through the mountains and lower lands, give admirable facilities for observing the measures lying between the sandstones of No. 11 and the upper coal measures. Apart from its varied mineral and agricultural resources this section of country has great historic interest attaching to it. It was down the Monongahela that Braddock led his ill-fated army to its defeat under the wails of Port Duquesne, and it was up the Youghiogheny River and Dunbar Creek that the shattered remnants hastily fled to gain the camp of Colonel Dunbar, the second in command, who was entrenched upon a high knob, at the head of the creek which bears his name, and which is still known and visited as Dunbar's Camp. Numerous streams, runs, and localities preserve the names of the guides and pioneers who accompanied, in early colonial times, young George Washington, who was pushing his surveys into the trackless and hostile wilderness, and many of them taking up large tracts of

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946