Search Documents

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By J. V. Belke

There are many aspects of a grinding mill supply and installation that can result in the mill not operating as intended, resulting in unplanned shutdowns, poor reliability and headaches for all concerned. One of the largest aspects, both in criticality and physical mass, is the mill foundation; if not properly specified, designed and constructed the mill operation will be compromised. The mill foundation starts with the design specification and loading diagram supplied by the mill builder. The importance of understanding these documents and how to apply them is critical for the start of any mill project. When designing mills with a GMD the foundation must be properly modeled to ensure that all interactions of the mill and motor structures, foundation and subsurface strata behave in the intended fashion. All of the previous efforts can be laid to waste if the construction of the mill foundation is poorly handled. Mill foundations are typically the most massive concrete structure at a processing plant and can easily cause nightmares for inexperienced contactors. This paper explores some of the more important facets along the lifecycle of the grinding mill foundation.

Feb 23, 2014

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

By P. A. Riveros

This paper describes the leaching of the common copper minerals tennantite (Cu12As4S13), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4) in acidic media using Fe(SO4)1.5, FeC13 or 02 as oxidizing agents. At temperatures <100°C, tennantite dissolves slowly in Fe(SO4)1.5-H2SO4 media, and the rate is directly proportional to the area of the sized tennantite. The rate increases sharply with increasing temperature and the apparent activation energy is 69 kJ/mol. Increasing Fe(SO4)1.5 concentrations slightly increase the tennantite leaching rate. The kinetics of dissolution of disks of synthetic iron-bearing tetrahedrite in Fe(SO4)1.5-H2SO4 media are linear; the leaching rates are slow but increase significantly with increasing temperature, with an apparent activation energy of 120 kJ/mol. The dissolution of sized particles of natural Ag-bearing tetrahedrite in FeC13- HC1 solutions proceeds according to the shrinking core model, and both Cu and Ag dissolve at about the same rate, provided that the total chloride concentration of the solution is sufficiently high to solubilize the AgC1 reaction product. The leaching rates are slow, and the apparent activation energy is 116 kJ/mol. The addition of sulphate ions to the FeC13-HC1 system reduces the tetrahedrite leaching rate to values similar to those realized in the Fe(SO4)1.5-H2SO4 system. At <100°C, enargite dissolves slowly in either Fe(SO4)1.5 or FeC13 media, and the dissolution rate obeys the shrinking core model. The rate increases with increasing temperature and the apparent activation energies are 50-64 kJ/mol. The rate increases slightly with increasing FeC13 concentrations in 0.3 M HC1 media. The leaching of enargite at elevated temperatures and pressures was also investigated. Potentially useful leaching rates are achieved above 170°C, at which temperature sulphate, rather than sulphur, is produced. Lower temperatures (130-160°C) lead to fast initial leaching rates, but the dissolution of the enargite is incomplete because of the coating of the enargite particles by elemental sulphur.

Jan 1, 2007

By I. Iwasaki

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron micro-probe, scanning electron microscope and scanning auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures which have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their implications to the flotation recovery of arsenide minerals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1985

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

By Raymond M. Coveney

Bedded sulfide ores in Cambrian Chinese black shales typically contains at least 2% Ni, 4.5% Mo, 1% As and 0.2% Se. Thin laminae and replaced on colites from the ore contain intimate mixtures of fine-grained Ni-rich sulfides and jordisite complicating ore treatment. The ores contain abundant jordisite, vaesite, nickelian pyrite, and barite and lesser amounts of sphalerite, gersdorffite, millerite, tennantite, fluorite, chalcopyrite, and HgSe (probably tiemannite). At present only ores that are sufficiently rich (>4.5% Mo) for direct roasting are mined and treated to produce, ammonium molybdate. The ores contain Pt, Pd, and Au in amounts totaling up to -2.5 ppm, but these are not recovered.

Jan 1, 1993

By Dirk van Zyl

The world is consuming more and more electronic products every year. This has caused a dangerous explosion in electronic scrap (e-waste) containing toxic chemicals and heavy metals that cannot be disposed of or recycled safely. But this problem can be avoided. We are pressing leading electronic companies to change; to turn back the toxic tide of e-waste. Every year, hundreds of thousands of old computers and mobile phones are dumped in landfills or burned in smelters. Thousands more are exported, often illegally, from the Europe, US, Japan and other industrialized countries, to Asia. There, workers at scrap yards, some of whom are children, are exposed to a cocktail of toxic chemicals and poisons.

May 1, 2008

By Lean P. J

The present The Zinc ODrporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) tailing dam (Site C) is expected to reach its terminal capacity late in 1985. Planning and design of new facilities for disposal of tailing after 1985 which includes new tailing dams (Site D) commenced during 1980. This paper briefly describes planning guidelines and specifications, location considerations, environmental aspects, operating strategy, engineering specifications, envirormental aspects and scheduling of works.

Jan 1, 1983

By J. V. Atwood

The U.S. Bureau of Mines has developed a novel Double Membrane Electrolytic Cell (DMEC) that exhibits unique features for recycling contaminated metals and metal alloys. The DMEC incorporates two anionic ion exchange membranes, separating anodic and cathodic regions of the cell. The ion exchange membranes prevent significant transport of unwanted cationic impurities to the catholyte from the impure anolyte while the anion/cation balance in cell compartments is maintained through the free movement of anions between compartments. The membrane barrier makes it possible to electro refine highly contaminated materials or to electrowin from solution while utilizing alternate anode reactions. Sinceanolyte and catholyte cross contamination has been eliminated, premium cathode products are produced. The DMEC has been tested at bench, pilot, and commercial scales. Configuration of the DMEC, cell operation, scale, up efforts, and significant design factors are discussed. Two separate recycling investigations utilizing DMEC technology are presented. The first investigation examines recovery of high purity cobalt and nickel from severely contaminated super aIloy scrap. The second involves? upgrading contaminated cobalt in the U.S. Government&apos;s National Defense Stockpile. Capital and operating costs for both potential applications are presented.

Jan 1, 1995

By A Scott

Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data û especially with semi-automated data acquisition by instrumented mine equipment. However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model. An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc not only have many areas of interest but also have very different conceptual models by which they evaluate performance. It is too ambitious to attempt to bring all of these cultures together û in a single step. However, the success of the Mine to MillTM project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from orebody model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is strongly focused on the technical requirements û not on the business model. This paper considers how to define at least some of the key decision points in terms of some case studies. Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning.

Jan 1, 2002

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970

By J. D. Embury, R. M. Fisher, A. S. Keh

An investigation of the defect structure and properties following large strain deformation has been carried out using transmission electron microscopy and mechanical testing for a range of ferrous materials and for copper. It is shown that, for a variety of ferrous materials, a cellular substructure is developed during the initial stages of working and on further deformation the dimensions of this substructure are reduced. Quantitative measurements of the flow stress and the scale of the substructure indicate that the strength of heavily worked materials is largely determined by the spacing of cell walls. These cell walls act as dislocation barriers in a manner analogous to grain boundaries. FCC materials do not harden as extensively as bcc after cold working and the present observations on copper indicate that the dimensions of the substructure in fcc materials are not markedly reduced on deformation. The differences between the fcc and bcc structures produced by large plastic strains are ascribed to differences in the extent of dynamic recovery. It is tentatively proposed that the greater stability of substructural barriers in bcc structures results from strong interstitial Pinning effects. It is proposed that for large plastic strains the work-hardening process may be considered in terms of the reduction of substructural-barrier spacing during the working process. This pvovides a simplified hut useful analysis of the strain hardening occurring during mechanical processes. THE mechanisms of strain-hardening processes have occupied the attention of numerous investigators over the past three decades and a multitude of theories have emerged in this field. The majority of previous work has been concerned with the development of a description of the plastic behavior of single crystals in terms of dislocation theory.&apos;" In contrast, scant attention has been given to the strengthening mechanisms operative during mechanical working processes such as rolling and drawing. The large plastic strains involved in these processes make it difficult to correlate the observations with any elementary dislocation theory. Further, as Bullen and coworkers3 have opined, for large plastic strains both hardening and recovery occur simultaneously and thus it is extremely difficult to estimate the effect of plastic strain on the ambient internal stress field. It is probable that for large plas- tic strains any theoretical estimate of the internal stress field must be made in terms of complex dislocation groups. Although some valuable theoretical work has been done toward calculating the elastic properties of dislocation groups4 any detailed self-consistent model for large plastic strain is as yet impossible. With these limitations in view it is still of value to examine the mechanical properties of highly strained materials as a function of their substructure. This relationship is explored in the present communication for a variety of materials subjected to rolling, drawing, or swaging. The primary object of this investigation has been to establish the validity and the limitations of the substructural strengthening mechanism proposed by Embury and eisher&apos; for drawn pearlitic wire and by Meieran and Thomas for drawn tungsten wire. No attempt has been made to delineate the basic interaction mechanism which occurs between a slip dislocation and the substructure and the authors believe that a great deal more experimental evidence must be compiled before these fundamental aspects can be explored. Also, no specific attention has been given to the detailed formation of substructure during working. Experimental Details. A variety of materials were used in this investigation, the compositions and heat treatment of which are tabulated in Table I. The commercially pure iron is referred to throughout this report as Ferrovac E. The mechanical working processes were all performed at room temperature. The wire drawing was performed on a manual drawing bench. Reductions of between 10 and 20 pct in area per pass were used in both swaging and drawing. The experimental parameter used to evaluate the mechanical properties of the materials was the 0.2 pct proof stress. This was determined for wire samples using an Instron tensile machine at a crosshead speed of 0.02 in. per min. The techniques for preparation of samples for transmission electron microscopy have been described previo~sl~.~ Specimens from wire samples were prepared from longitudinal sections and in some cases from transverse sections. To evaluate the substructural characteristics of rolled materials, thin foil samples were prepared of both the face and edge sections. Results. One of the more familiar ways of expressing work hardening in mechanical working is by the flow stress as a function of reduction in cross-sectional area. Fig. 1 shows such a plot for Ferrovac E eutectoid carbon steel and for copper. The curve for Ferrovac E is characterized by an initial stage of rapid work hardening and a final stage of rapid work hardening separated by an intermediate stage with a low rate of work hardening. This behavior is typical of many ferrous materials and the drawn pearlite wire previously investigated by Embury and Fisher is a more pronounced example. Copper shows an initial

Jan 1, 1967

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007

By Anthony T. Iannacchione

Longwall mining produces surface subsidence basins that affect streams by water diminution and contamination. These effects can ultimately impair the biological character of the plants and animal communities living in the streams. The combination of flow, water quality, and ecological effects threaten the environmental sustainability of longwall mining and, ultimately its social acceptability. Pennsylvania has developed new standards, released in 2005 and implemented in 2007, to help protect the commonwealth?s valuable streams from the detrimental effects of subsidence. These standards are aimed at eliminating environmental problems and will therefore help to make underground bituminous coal mining more sustainable. The engineering solutions necessary to comply with these standards are fundamentally affected by the geologic nature of coal-bearing strata, the existing in-situ stress conditions, and the ability of selected species to survive and adapt to changes in their environment caused by longwall coal mining subsidence. Needless to say, geologists, biologists, and engineers are all playing a pivotal role in developing prevention controls and recovery measures necessary to protect streams and sustain underground coal mining. The challenges facing scientists and engineers in sustaining the development of underground coal mining in Pennsylvania are examined through case studies. These challenges all arise from the subsidence effects of longwall mining. The key effects of subsidence, discussed through case studies, are: a) tension cracks, b) springs in headwater stream areas, c) stream gradients and subsidence basins, and d) stream compression ruptures and horizontal stress. All of these potential threats demonstrate the need for high-level scientific knowledge and innovative engineering solutions. One could argue that Pennsylvania?s stringent stream protection standards put the coal mining industry at a competitive disadvantage compared to other coal producing states. It is equally likely that compliance with these standards help to mitigate the effect of subsidence, thereby helping the coal industry achieve a sustainable future.

Jan 1, 2011

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

By Andrew P. Ritter, Douglas A. Anderson, Stephen R. Winzer

We have adopted a unified approach to blast design. Based on earlier research, we chose minimum relief of 3.4 ms/ft between holes in a row and 8.6 ms/ft between echelons to produce good fragmentation. A model has been created which generates the expected ground vibration frequencies from a particular delay pattern. Within the relief guidelines, blast designs have been created to shift the expected frequencies of the ground vibration above the resonant range of residential structures. A programmable sequential blasting machine was used to delay circuits. An extensive three-month seismic monitoring program determined that this approach is successful. From data collected for over a year, we have determined that crusher throughput is up about 10%, frequency modification has been largely successful, peak particle velocities have generally gone down by a factor of 2, and neighbor complaints have decreased drastically.

Jan 1, 1982