Search Documents

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount lVIorgan mine. It will be admitted that in all mining operation, the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be ineluded, as it is necessary to understand the eonditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan.

Jan 1, 1910

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By Hongfei Li, JianLong Wang

This paper introduces the technical characteristics, transformation scheme and production practice of the project in which Copper P-S Converter was replaced by Bottom Blowing Continuous converting for the first time, and introduces the technical achievements obtained by the project. The application practice proves that bottom blowing copper continuous converting technology can completely solve the problems of fugitive off-gas pollution in the ladle transportation, large amount of flue gas and fluctuation of flue gas caused by P-S converting. Comprehensive energy consumption and operating costs of producing blister copper, safety and environmental risks are greatly reduced, and economic, environmental and social benefits are significant. It is one of the preferred technologies for upgrade and to replace P-S converting technology. INTRODUCTION At present, more than 80% of copper production capacity is still using the P-S converting technology with a history of more than 100 years. During P-S converting process, melted copper matte needs to be transported by ladle, and it needs to rotate the furnace body several times, causing a lot of serious environmental and safety risks such as SO2 flue gas emission and low-altitude SO2 pollution. In addition, the high operating cost caused by low rate of air blowing, the short life of the refractory materials and high energy consumption during P-S converting become big problems. Other problems such as large amount of flue gas, low SO2 concentration, large fluctuation of flue gas volume and SO2 concentration, and discontinuous flue gas cause high cost of subsequent flue gas treatment are also needing to be solved. In order to solve these problems during the P-S converting, metallurgical engineer in various countries has spared a lot of efforts to develop continuous blowing process for decades. The continuous converting that have been industrially applied are flash continuous converting, Mitsubishi continuous converting, Noranda continuous converting, Bottom Blowing Continuous converting and multi-lance top blowing continuous converting

Jan 1, 2019

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By Theodore H. Orem

In 1928 Elam,1 discussing the subject of twinning in metals, disclosed that she had observed this phenomenon in aluminum, a metal little susceptible to twinning. The twinning described was one in which the boundary between the twinned portions was not a geometric plane but appeared, in one section, more like a normal grain boundary. Under these circumstances twinning might remain unrecognized by an observer of microscopic sections. She therefore suggested that twinning in aluminum might be much more prevalent than expected. Whereas the parallel composition lines shown in sections of polysynthetic twins were characteristic of the phenomenon of twinning, Elam pointed out that from the absence of

Jan 1, 1963

By Mark Larson, Doug Tesarik, Joe Shoemaker, Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the roof and floor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right mine through and should provide beneficial case study information for other longwall backfilling applications in the future.

By M. Greyling, C. Panaou, M. Bellino

Commonly the most frequent method of calculating the overall mass balance of a multi mineral platinum-group metal (PGM) concentrator circuit in Southern Africa has been through the use of spreadsheets, typically Microsoft EXCEL®. While there are some advantages in using spreadsheet based mass balances during the conceptual design phase of the project, their use becomes limited in the detailed design phase of the project. This paper discusses the successful application of METSIM® for mass balancing of a PGM concentrator and highlights the benefits gained during the conceptual and design phase of the project.

Jan 1, 2005

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By Eduardo Simian

El presente texto señala las condiciones adecuadas de las inversiones respecto al cobre en Chile. Así también se define las cinco materias que definen la política del Gobierno para el desarrollo de la industria cuprífera chilena como la idea de refinación, franquicias y garantías de las inversiones, intervención en el comercio, adquisiciones en el país y las sociedades mixtas.

Nov 1, 1965

By D. P. Power

The development of an accounting code for the metallurgical industry has been debated for many years. Following the series of tumultuous economic events in the nineties and earlier this century that have affected business, there was much need for legislation to be passed to minimize potential risk. One of the consequences to affect the mining industry was the enhancement of existing geological codes for reporting. In parallel the sponsors of AMIRA have taken the brave step to develop a generic code for metal accounting that embraces the full gamut of industry. In this paper the code will be reviewed in the context of metallurgical accounting as it applies to coal preparation. This paper provides the background for this development and an insight into the mechanism for the debate for the generation of this code. The key elements of the code as it applies to the coal industry are explained but most importantly the key opportunities are highlighted.

Jan 1, 2010

By P. G. Vikre

Several factors have caused less emphasis to be placed on geologic mapping in mineral exploration in the last 15 years. These include opportunities for "easy" discoveries of near surface gold and silver deposits in developed countries, and of base metal deposits as well in less developed countries, a decline of emphasis on geologic mapping in many universities, and a decline of useful mapping by government agencies in many areas. Geologic mapping is simply a way of recording geologic observations on volumes of rock larger than can be seen from one place. Since most geologic processes involve systems larger than this, mapping is also essential to understand the significance of observations made on smaller volumes of rock, such as thin sections and sample taken for chemical or isotopic analysis. To be useful, the observations recorded through geologic mapping are then interpreted to arrive at an understanding of the 3D geometry and geologic history of a volume of rock, which is used to direct mineral exploration, or any number of other purposes.

Jan 1, 1995

By M. P. Bohrer

A closed-loop hydrometallurgical process has been developed for treatment of smelter flue dust generated by copper recycling. The process is a semi-continuous operation in which zinc, iron, and copper are first extracted from the dust with a sulfuric acid solution. The lead and precious metals, initially present in the dust, remain as solids and can be recycled to the copper smelting furnace. Cementation with iron and zinc metal purifies the zinc and iron-rich liquid stream prior to spray drying. The spray-dried product, consisting of a mixture of zinc sulfate monohydrate and iron sulfate monohydrate, is a desirable micronutrient additive for use in animal feeds. Treatment of the smelter flue dust in this manner will generate a positive return on investment, as well as mitigate a potential environmental liability.

Jan 1, 1992

(Members are urged 'to, send in for this column any notes of interest concerning themselves or, their fellow-members.) Members and guests who registered at Institute headquarters during the period Sept. 10 to Oct. 10, 1915: George H. Blakemore, Sydney, N. S. W. W. B. A. Dingwall, San Antonio, Tex.. H. Haege, Sydney, N. S. W. R. H. Jeffrey, London, England. C. A. Filteau, New York, N. Y. H. S. Emlaw, Spring Lake, Mich. Myron R. Walker, Cerro de Pasco, Peru. Y. T. Woo,' Tientsin, China. William R. Grunow, Morenci, Ariz. A. L. DeDeken, LouVain, Belgium. E. DeGolyer, Norman, Okla. K. P. Swensen, Tokyo, Japan. William W. Elmer, Tuttletown, Cal. Charles Enzian, Wilkes-Barre, Pa. Huntington Adams, Iquique, Chile. C. F. Schnepp, Cobalt, Ont., Canada. W. Ray Cox, for several years Mineral Inspector of the General Land Office at Portland, Ore., has been appointed Professor of Mining and Metallurgy in the School of Mines, Oregon Agricultural College, Corvallis, Ore.

Jan 11, 1915

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By Juan Silbino Marceliano Rojas

Volcan Compañía Minera S.A.A. es una empresa minera peruana que inicia sus operaciones en el año 1943. A lo largo de sus 71 años ha logrado posicionarse como la primera productora de plata, plomo y la segunda en zinc a nivel nacional. Durante este periodo la compañía se ha expandido y ha alcanzado excelentes resultados de productividad. Sin embargo, estos resultados no han sido acompañados de indicadores de seguridad favorables. En los últimos 12 años (2000-2011) se han presentado 88 fatalidades, 960 accidentes incapacitantes y 1400 accidentes leves. En el 2012, la dirección de la organización decide realizar un cambio trascendental en la gestión de seguridad, estableciendo como primer objetivo estratégico de la compañía la implementación de una cultura de seguridad de clase mundial para minimizar la frecuencia y la severidad de los accidentes de trabajo. Partiendo de este objetivo en el año 2012 realizó un diagnóstico a nivel corporativo que nos ubicó en una fase de dependencia en relación a la curva de cambio de cultura, tomando como base el concepto de Bradley e identificó la necesidad de efectuar un cambio en dos frentes: Sistema de Gestión SSO y Líderes. Diseñamos una "Estructura Organizacional" en los tres niveles de operaciones, lo que involucró a los líderes y evidenció así el "Liderazgo Visible". El sistema se basó en cuatro pilares fundamentales y aplicó las siguientes herramientas: gestión de riesgos, condiciones, conocimiento y comportamiento. Dentro del pilar condiciones, priorizamos doce riesgos críticos para contener los accidentes mortales e incapacitantes. Los Líderes fueron entrenados en la herramienta de gestión y en los cuatro pilares del sistema. De esta manera se logró el impacto directo en la supervisión y los trabajadores, así como desarrollar las competencias de comunicación, motivación, retroalimentación, confianza y compromiso. El modelo está evolucionando la cultura de seguridad hacia una fase de interdependencia. Hemos reducido los índices de frecuencia en un 55%, severidad en un 92% y accidentabilidad en 96%, sin embargo nuestro logro más importante es la contención de los accidentes mortales a la fecha.

Sep 21, 2015

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990

By J. Iannicelli

Availability of large-scale high field/high gradient magnetic separators during the past five years allows applications of magnetic separation to feebly paramagnetic materials which have been considered nonmagnetic in the past. Technology is now available for magnetically attracting not only feebly magnetic compounds of iron such as hematite and pyrite, but also hundreds of compounds of nonferromagnetic elements such as copper, tin, uranium, vanadium. Besides enabling novel separation of industrial minerals, metallic ores, and coal, the new technology also can be used in effluent treatment, catalyst cleanup, and purification of chemicals.

Jan 1, 1979

A production drill rig at a site in Sweden was equipped with a monitoring system to estimate production statistics. Drill running times, drill hole depths, penetration rate, rotation speed, thrust, air percussive pressure and torque pressure were recorded for every 10 mm of hole length for a period of 5 months. Operational activities (rock penetration, tube handling, moving and set-up time) accounted for almost 62% of the time consumed, the remaining 38% being different types of stoppage. Drilling itself, as opposed to handling, took less than 24% of the total time. The results give an indication of how the overall drilling capacity can be increased and which activity should be emphasised. The impacts of automation, new developments and reorganisation on production can also be predicted. Average production was found to be around 100 m/day, but varied between 50 and 160 m/d. The company's specification for the drill rig, before purchase, was that an average production rate of 130 m/d be attained over two consecutive months of drilling - a rate which monitoring shows will not be achieved

Jun 19, 1905