Search Documents

By Xiyun Yang

Magnetite was prepared by hydrogen reduction method. For a conversion to cobalt-modified magnetite, magnetite particles were suspended into a solution containing Co2+ and Fe2+ to precipitate a cobalt ferrite layer on the surface. pH value influences the particle composition directly, the desirable CoFe2O4 is obtained when pH value is 12. The coercivity increases with the increase of cobalt content, cobalt efficiency reaches a maximum value at cobalt content of 2.71wt%. With cobalt modification, magnetite particles have similar lattice constant and squareness ratio to that without cobalt modification. TEM and XPS analyses indicate that acicular morphology is retained during the coating process, the epitaxial growth layer consists of CoFe2O4and 0.3Co2O3CoFe2O4 at cobalt content of 2.71wt% and 5.03wt%, respectively.

Jan 1, 2006

By C. Tan, C. Detournay

Wellbore stability is a major concern for drilling in naturally fractured formations. The infiltration of drilling mud into the fractures is a factor, which may compromise wellbore integrity due to the loss of strength experienced by the fractures. The reduction in the fracture frictional and cohesive properties is attributed to weakening of the infill materials and lubrication of fracture asperities by the mud filtrate. One way to investigate the influence of mud infiltration on wellbore stability in fractured formations is to use a numerical modeling approach. A requirement for the numerical model is the ability to predict the region of mud infiltration. This paper describes a numerical technique to model the extent of mud infiltration for application in coupled fluid-mechanical simulations in densely fractured rock masses using the computer code, UDEC. Several factors are considered including fracture pattern, in-situ stresses, reduction in joint frictional angle and cohesion, viscosity of the mud filtrate and fracture plugging. Results of numerical simulations are presented to illustrate the technique and show the influence of these factors on the extent of mud infiltration. Un des problèmes importants posés par le forage en milieu fissuré saturé, est celui du maintient de la stabilité du puit. L’infiltration de boue de forage dans le massif peut avoir pour effet de réduire les propriétés frictionnelles et cohésives des fractures et de compromettre ainsi la stabilité du puit de forage. Le radoucissement des propriétés des fractures est attribué à la dégradation du materiau de remplissage et au pouvoir lubrifiant des boues. L’analyse numérique offre un moyen d’investiguer l’influence jouée par l’infiltration de boue sur la stabilité du puit. Un des critères de sélection du modèle numérique sera son pouvoir de prédiction du domaine d’infiltration de boue. Cet article décrit une technique numérique permettant de modéliser l’infiltration de boue de forage dans le cadre de simulations hydro-mécaniques, en milieu à haute densité de fractures, effectuées avec le logiciel de calcul UDEC. Parmis les facteurs tenus en compte, on trouvera la nature du réseau de fractures, les contraintes in-situ, le radoucissement en friction et cohésion des joints, la viscosité de la boue et le bourrage des fractures. Des résultats de simulations sont présentés pour illustrer la technique et montrer l’influence de ces facteurs sur la taille du domaine d’infiltration de boue. Bohrlochstabilität ist ein wichtiger Aspekt für das Bohren in geklüfteten Gebirgsformationen. Das Eindringen der Bohrlochstützflüssigkeit in die Klüfte kann die Bohrlochintegrität wegen des Verlustes der Festigkeit des Kluftsystems gefährden. Die Reduktion der Reibung und kohäsiven Eigenschaften ist der Schwächung der Kluftfüllung und der Schmierwirkung der eingerungenen Stützflüssigkeit in Bezug auf die Kluft-Asperities geschuldet. Numerische Berechnungen sind ein Weg zur Untersuchung des Einflusses der Infiltration der Bohrlochstützflüssigkeit auf die Bohrlochstabilität in geklüfteten Gebirgsformationen. Eine Voraussetzung für numerische Modelle ist die Fähigkeit den Bereich der Infiltration der Stützflüssigkeit zu prognostizieren. Diese Publikation beschreibt ein numerisches Verfahren, um die Reichweite der Infiltration von Stützflüssigkeiten mittels fluid-mechanisch gekoppelter Simulationen im engständig geklüfteten Gebirge mit dem Programm UDEC zu modellieren. Verschiedene Faktoren, wie Kluftmuster, Gebirgsspannungszustand, Reduktion von Kluftreibungswinkel- und kohäsion, Viskosität der Stützflüssigkeit und Rissabdichtung wurden untersucht. Ergebnisse numerischer Simulationen werden präsentiert, um die Vorgehensweise zu illu

Jan 1, 2003

By Paul L. Horrer

Costly damage by severe wave attack to many engineering structures has illustrated the need for a consideration of the nature of wave action in plans for offshore drilling operations. Using wave data it is possible to answer questions pertaining to engineering problems such as platform elevation, structure orientation, and expected wave forces. For locations where wave records are not available a technique can be used to obtain information about wave characteristics from past meteorological data and near shore submarine topography. Forces exerted on structures by waves may be divided into four parts. A completed study is given in which frequencies of various wave heights and maximum frictional drag forces are computed for a typical offshore drilling site. INTRODUCTION Waves of tremendous proportions accompanying hurricane winds crash against breakwaters and other offshore structures causing untold damages. Wave forces exerted on structures at these times are enormous, as shown by past records of incidents where massive portions of breakwaters have been broken off and moved by waves. On other similar occasions, whole structure; have been unloosed and smashed or floated away. These incidents, which seem almost incredible, serve to illustrate the great amount of energy contained in large waves, and to show that this energy results in powerful forces destructive to offshore installation~ which are not designed sufficiently strong to withstand wave attack. In the past the expected frequencies of waves having various characteristic.% have rarely been considered in the design of structure affected by wave action. As a result, many structures have failed to accomplish the purpose for which they were designed or have collapsed under wave attack. Others have been constructed to withstand greater wave energy than is ever encountered, with resulting waste of material and construction time. In this study an analysis is made of the frequencies of waves having different characteristics which affect the plans for offshore drilling installations. After such an analysis the erection of these structures can proceed with less risk involved and with more efficiency and economy. ENGINEERING ASPECTS In the offshore drilling program wave forces play an extremely important part in design and construction of drilling rigs in shallow water. The design of a platform or other structure from which drilling equipment is operated is critical, becauze any damage to the platform may endanger personnel and result in complete loss of equipment. Since a platform built too close to the water would be battered by breakers, and one built unnecessarily high would involve undue expense, it is necessary to know the most desirable elevation at which the platform should be erected. This is only one of many questions about structural planning which can be answered using existing technique for determining wave characteristics. The purpose of efficient design for the portions of many types of offshore structures which are acted upon by wave forces is the same as that of all designs which deal with frictional forces of a fluid on a solid. For these structures the problem is comparable to that encountered by undersea craft moving through water, except that in the case of a fixed structure the force is produced by the water moving past the model. For off shore sructures which are extremely rigid the frictional forces may be nearly negligible compared with the impact or shock forces imparted by breaking waves. In all case; the better design is that which offers the least resistance to the opposing forces. From a consideration of wave forces, each drilling structure varies in efficiency depending upon the type and amount of superstructure in contact with the waves. For example, round piling and bracing offer less resistance to wave forces than do I-shaped ones. All network superstructure such as cross bracing should be kept to a minimum and at as low an elevation as possible, so that it will not expecience the pressure exerted at the tops of breaking waves. Models of proposed structures can be tested in wave tanks and in the field to ascertain the efficiency of specific designs. Past experience in beach and shoreline engineering has shown that, although changes in the topography of the bottom very near shore do not seem to be occurring, the natural forces involved may be in a delicate balance such that a static state exists. Interruptions of any of these natural forces by erecting offshore structures are likely to cause undesirable effects. Changes in beach profile result partly from sediment being brought into suspension by the orbital motion of waves and partly from the transport of sediment by longshore currents. With the erection of an offshore structure and consequent change in the combined effects of these two forces, unfavorable deposition upon, or erosion of, the bottom at the site may occur. Therefore, combination wave and current studies are essential for the solution of problems involved in the design of most marine structures. TECHNIQUE FOR OBTAINING WAVE INFORMATION In determining the probable effect of wave action on an offshore drilling structure, it is first necessary to know the usual frequencies of certain wave types for the given location. A technique has been developed which provides a means for obtaining information about wave characteristics in the

Jan 1, 1949

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By Jiling Wang, Xuefeng Liu, Haojian Duan, Lifeng Zhang, Ying Ren, Wen Yang

"In order to study the influence of MgO-C refractory on steel cleanliness and inclusions during steelmaking process, and to understand the reaction mechanism deeply, laboratory deoxidation and equilibrium experiments were respectively performed in MgO crucibles at 1873K. In the former experiment, after Al addition, steel samples were taken at different holding time. In the latter experiment, different slag components and different contents of carbon and aluminum in steel were considered respectively. The inclusion characteristics of each experiment were analyzed. The results showed that with the increasing of holding time after deoxidation by Al, MgO existed in the small inclusions firstly, and then in the large ones such as the clusters. The MgO content in the inclusions increased with the increasing of holding time, indicating that the MgO in crucible could be individually reduced by the aluminum in the molten steel. The reaction could occur within nine minutes.IntroductionNon-metallic inclusions would have positive or negative effect on steel quality depend on the quantity, size and composition of inclusions. Large inclusions are always detrimental. From the point of view of inclusion property, plastic inclusions are required by steel cord, while hard inclusions are preferred by pipeline steel. One of the most important ways to increase the steel quality is reducing the inclusion size and controlling the inclusion composition in steel. Nowadays, MgO based refractory is used as ladle glaze material with more and more frequency, which results in different inclusion characteristics in molten steel, for example, the inevitable generation of MgO contained inclusions during ladle treatment of steel. In other words, the inclusions in this type ladle will influence on the steel cleanliness and the product property. Thus, keeping an eye on the inclusion formation behavior in the steel with MgO-C ladle glaze is important for the steel industry. There have been a few studies in this regard. Li et al[l] studied the reactions between MgO-C refractory, molten slag and metal using a high temperature X-ray radiographic apparatus. They found that the local corrosion was regarded as due to the cyclic dissolution of MgO and graphite in the refractory into slag and metal phase. The gas bubbles formed according to the reaction of (FeO)+C(s)=Fe(l)+CO(g) greatly influenced the corrosion. On an industrial scale, Du[2] found that ladle glaze is a major source of inclusions in the ladle. An experimental study has been performed by Lehmann in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel[3]."

Jan 1, 2014

By John Dean Smith

In order to discuss problem solving techniques for the future. we must first review the past. This paper will discuss the drilling and blasting problems and techniques that were used by .Imax Coal in the past few years, tn those of today.

Jan 1, 1991

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By B Broad

"Establishing ventilation in the early stages of a new mine is an essential step to achieve scheduled outcomes that ultimately drive the financial success of an operation. If the primary ventilation is not in place in time to support a contractorÆs work output, then the ore delivery is likely to be severely impacted. Options to increase ventilation in order to address shortfalls are limited. This in turn can lead to reduced revenue generation at a time when a mine is at its highest capital outlay. This can have implications for any company, but even more for an explorer moving to producer. The ventilation put in place to cover the start-up period is also unlikely to cover any extended or increased load required to meet schedule delays.The following paper examines two issues in relation to ventilation with a focus on small to medium projects where the company is establishing a mine using a mining contractor. The issues being: potential impacts on the contract and tender process when using a mining contractor key mine design considerations, such as æcrunch timeÆ, as they interact with ventilation achieving a successful ramp up.A recommendation is made for higher levels of detail around secondary ventilation leading up to the primary fan installation. The information should be included as part of the tendering process and preliminary project execution planning. Understanding the æcrunch timeÆ concept can lead to strategies, as well as back up plans, to minimise any negative impact.By understanding key risks around primary ventilation establishment for a new mine, detailed design work can be completed where it is needed most. Value is added by reducing uncertainty and a payback with better contract terms and a more robust ramp up plan. This will improve the economic return for the company and reduce the risk.CITATION:Broad, B, 2013. Contract considerations and other critical ventilation aspects in achieving a new mine ramp up, in Proceedings The Australian Mine Ventilation Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013

By L. Zeka, I. Ndala, J. Frenay, S. Gaydardzhiev

"Reductive leaching of cobalt (III) from a heterogenite bearing ore has been performed. Pyrite was added to the system and simultaneously bioleached in order to provide ferrous iron as reducing agent. Within such arrangement the iron ions are continuously re-circulated inside a Fe 3+ / Fe 2+ loop. As a result Co(III) is solubilized in the presence of Fe 2+ ions in concentrations well below the stoichiometric requirement. The ore has been initially subjected to acid pre-leaching in order to guarantee that the available Co (II) has been entirely removed. Two technological parameters have been studied to show influence on the degree of cobalt leaching: concentration of ferric iron in the inoculum and the presence of bacteria. The bacterial role could be mainly viewed in supplying ferric ions in the system which chemically react with the pyrite to generate ferrous ions used as Co(III) reducing agent. Co(III) dissolution has been less efficient when the concentration of total iron in the system was low, but also when microorganisms were absent. SEM observations on leached heterogenite have evidenced bacterial attack on the mineral; however the precise role of bacterial presence on cobalt (III) leaching is still to be elucidated.INTRODUCTIONCobalt accompanies quite often copper in secondary oxidized ore deposits (Rumbu, 2013). In such associations cobalt is found both as CoII+ as well as CoIII+ (Deliens, 1974). In contrast to cobalt (III), cobalt (II) is leached relatively easy in sulphuric acid solutions. Cobalt (III) when present in mineral form belongs to the heterogenite mineral group with a simplified chemical formulae Co2O3.H2O or CoOOH. In order to be brought in solution, heterogenite should capture two electrons, likewise shown in reaction 1 below:"

Jan 1, 2016

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By J. S. Moretzsohn, D. F. Graham

"Airborne Synthetic Aperture Radar (SAR)was acquired over the Carajás Mineral Province, within the rainforests of the Amazon, which hosts the world’s largest Fe-ore deposit(Santos, 1986). Significant chemical weathering exists in this humid environment. PrevalentAu mineralization is thought to be generally associated with deformation zones in Archean schists.Radar data have proven to be very useful as an aid to geological mapping in the tropical rainforests of the Amazon Basin in Brazil. In these densely vegetated areas, a sense of regional structural trends is obtained as a con-sequence of the sensor/terrain geometry. The top forest canopy is the main terrain reflector of X-band radar energy, and consequently is the main terrain surface feature expressed in processed radar imagery. Radar is important for extending t,he continuity of mapped structural lineaments. Differential weathering is related to variations in radar image texture which is used to infer gross lithologic variations and relative age relationships of major rock units. Specifically, quartzites and banded iron formation are highlighted in the radar imagery due to their unique tonal and textural appearance, in contrast to schists, gneisses and metavolcanic rocks. As tropical areas are typically enveloped in cloud or mist, radar data are invaluable in providing information for logistical planning of field mapping activities."

Jan 1, 1997

By F. Goodarzi

"The nature and distribution of the inorganic components and the concentration of certain environmentally sensitive elements, such as, As, Sb, B, Hr, Cd, CI, F, Mo, Pb, S, and Se, or elements detrimental to the utilization by industry such as B, Na, P and S are very important in determining coal quality. The concentration of elements in coal is controlled by the following factors: (1) frequency of occurrence of partings; (2) nature and habit of occurrence of minerals in coal; (3) environment of coal deposition; (4)rank; (5) geological setting; and (6) weathering.Selective mining of coal can reduce the input of undesirable elements such as As and S by eliminating the part of the seam which is enriched in these elements. IntroductionCoal is a sedimentary rock of plant origin and consists of two components: an inorganic component (minerals) which is formed by influx of clastic sediments into the coal-forming environment and also by activities of groundwater, and an organic component (macerals) which is formed from plant debris deposited in the original coal-forming environment. However, coal is a generic term with a broad range of utilization characteristics. A coal that is attractive for use in one market - such as generation of electricity (combustion) - may not necessarily be acceptable for use in another, such as for production of coke (Davis, 1978).The elements in coal are associated with both macerals and minerals. The elements associated with coal macerals, such as C, H and N are termed elements with organic affInities. The concentration of elements with organic affmities (including B, Br, CI, F, I, S, and Mg) often decrease with increasing ash content of coal (Nicholls, 1968; and Finkehnan,1982). FIgure 1 shows such a trend for chlorine. Some of these elements may also be incorporated in coal maceral as very fine mineral grains (Finkelman, 1982). The elements with organic affmities are often volatilized during combustion and carbonization of coal and emitted in the vapour phase. Emission of some of these elements (C, 0, Br, N and S) is of major environmental concern (Lim, 1979)."

Jan 1, 1994

By J. H. Bechtold

Tensile properties of annealed molybdenum were investigated from 1000" to—200°C. In the vicinity of room temperature a well-defined transition in tensile properties occurs. Reduction in area decreases from over 80 pct to 0 pct and, simultaneously, the yield strength increases about 60,000 psi. MOLYBDENUM, tungsten, iron, and many other metals and alloys with the body-centered cubic and hexagonal close-packed crystal structures change from ductile to brittle behavior over some relatively narrow temperature range. The temperature at which this transition in ductility occurs depends on chemical composition, microstructure, and method of testing. When fine grained, completely recrystallized molybdenum of commercial purity is tested in uniaxial tension at a slow strain rate, the transition occurs at slightly below room temperature.' Iron2 and tungsten3 tested under similar conditions become brittle at temperatures close to the boiling point of nitrogen, — 195°C and at about 200°C, respectively. A sharp change in ductility is uncommon in metals with the face-centered cubic crystal structure, however, a relatively sharp transi- tion in notched bar impact properties has been observed below room temperature in a face-centered cubic copper-antimony alloy.4 A transition from ductile to brittle behavior is usually explained by the concepts originally developed by Ludwik,5 and discussed and elaborated on by others including Orowan,6 Hollomon and Jaffe,7 and Gensamer8 In brief, there are two aspects to strength, first the resistance to flow and second the resistance to fracture. Both are functions of temperature, strain, strain rate, stress system, composition, and microstructure. With decreased test temperature the flow stress required to initiate plastic deformation increases more rapidly than the fracture strength and brittle fracture occurs at that temperature where the yield strength equals or exceeds a brittle fracture strength. This investigation was conducted to determine the effects of temperature, strain, and rate of straining on the flow and fracture strengths of molybdenum above, through, and below the ductile-to-brittle transition. Other variables were held constant during testing. This information is believed to show

Jan 1, 1954

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By W. A. Crosby, A. Bauer

The recent increase in size of open-pit mining operations has resulted in major improvements in efficiency that are beneficial to the mining industry. Higher bench heights, larger diameter blast-holes, and more powerful explosives have played an important part in reducing mining costs. These measures have, however, resulted in increased energy concentrations in the blast area, which can result in severe backbreak problems for final pit walls. If backbreak is not controlled, a decrease in the overall pit slope angle will ultimately be necessary, and consequences, such as decreased recoverable ore reserves and increased waste-to-ore ratios, will result. Greater amounts of loose face rock will be produced, and planned safety berms will be less effective or nonexistent. Hazardous working conditions can also result. Remedial measures, such as scaling large areas and using wire mesh or other artificial support, are very expensive and difficult to implement. There must be a trade-off between the money saved by using larger blasts, and the time spent to maintain pit wall quality. The best approach is to control blasting effects so the inherent strength of pit walls is not destroyed. Presplit and trim blasting are two control blasting techniques used to accomplish this. Both techniques are designed to create a low explosive energy concentration per unit of wall area at the perimeter of the pit. Energy concentration of the main production blast must also be controlled to avoid damaging the final pit wall. A low-energy concentration at the final wall can be obtained by decoupling charges, decking charges, using less powerful explosives, decreasing blasthole diameters, and changing the burden and spacing. Rock properties-fragmentation and the final state of the pit wall-influence the success of a blast. The most important properties to consider are: in situ rock strength, and the nature, frequency, and orientation of structural features. Since these variables cannot be controlled, they must be evaluated by suitable field tests, and then a control blast can be designed using controllable variables, such as spacing, burden, and hole diameter, so the blast will be successful for appropriate rock conditions. One main thrust of this article is to show how control blasts can be successfully designed for larger hole sizes, up to 381-mm-diam. While efforts to produce a good control blast in shovel/truck pits have been ongoing for some time, recent use of a modified presplit technique in dragline operations has helped reduce water problems, improve safety, and increase dragline productivity in a number of surface coal mines. This article presents examples on designing and using presplit and trim blasting for large hole operations in both shovel/truck and dragline mines. Presplit Blasting As introduction to presplit blasting, Fig. 1 illustrates a typical presplit blast layout using 102 mm-diam presplit holes for 381¬mm-diam production holes. For this type of blast, presplit holes would normally be drilled first, ahead of main production holes. The choice can then be made between loading and firing the presplit line or infilling the main blast. In the latter case, the presplit line would be fired instantaneously 100-150 milliseconds before the main blast. As shown in the figure, the presplit line is formed ahead of the main

Jan 2, 1982

By Percy Zamora

El presente trabajo da a conocer el crecimiento que ha tenido el yacimiento Tantahuatay desde el inicio de las operaciones en Agosto del 2011 con sólo 658 Koz Au en reservas de mineral llegando a reportar a Diciembre 2016, 1.0 Moz Au en la misma categoría, y con un número casi igual en onzas de producción (onzas puestas en Pad) acumulado.

Sep 1, 2017

By K. Sawada

Along with the expanding demand of copper concentrate in Asian countries, custom-smelters have confronted with difficulties of low TC/RC. Now, Japanese Copper Industry have 2 options; investment in mine development and/or recycling of copper scraps. The strategy of global mining companies is analyzed, and implications for Japanese Copper Industry will be discussed from the viewpoint of sustainability of smelters in Japan.

Jan 1, 2014

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960