Search Documents

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By Hewitt Wilson

A review is given of the nomenclature, sources, imports, statistics, common methods of preparation, and testing of mineral pigments. A description of the Deer Park-Spokane colored-clay district and the laboratory methods of preparation of these colored clays, others, and siennas follows. The mineral pigments were prepared by washing or grinding the original material as received and by calcination of the yellow ocher and brown sienna with and without manganese dioxide to produce red, brown, and black colors. These prepared powders were tested for fineness, oil absorption, and color as compared with well-known brands of commercial pigments. Similar tests were made with several basalt red clays occurring in the neighborhood of Salem, Oreg., and Kalama, Eatonville, and Clay City, Wash. The color particularly was studied, since this property is the most important commercial characteristic of the minerals. PURPOSE OF INVESTIGATION Since the development of the clay industry in the Pacific Northwest, some curiosity and interest have been aroused by the red and yellow clay or ocherouslike material that has often been found associated with the commercial clay deposits. These include the red and yellow "paint pots" near Deer Park and Spokane in eastern Washington, a red clay at Clay City, another close to Eatonville in western Washington, and red basalt earths near Salem, Oreg., and along the Columbia River near Kalama, Wash. Several companies have been organized to produce pigment colors from two of these deposits but have either discontinued or never started operations.

Jan 1, 1929

By J. Rowe

The attrition of activated carbon, and the loss of gold associated with it, is of significant economic importance to the operation of a CIP/CIL circuit The focus of this study was on activated carbon recovered from an elution circuit which was deemed too fine for reuse. Results of cyclosizer and laser particle size analysis identified that most of the carbon was contained in the larger size fraction suggesting formation by abrasion. Digestion and AAS analysis of the individual size fractions identified a disproportionate concentration of gold in the finer size fractions which was identified by scanning electron microscopy to be due to the presence of fine metallic gold formed as a result of the acid washing process. Attempts to strip the remaining gold using sodium hydroxide or sodium sulphide based solutions proved unsuccessful due to poor elution efficiencies and re adsorption of gold. Upgrading of the material by froth flotation was also investigated using various conventional flotation reagents which had some success in concentrating the free metallic gold, however, grade and/or recoveries were considered less than desirable. Greater success was ultimately found in the transfer of gold from the fine carbon material onto coarser virgin activated carbon using a caustic cyanide solution. Sodium sulphide, sodium chloride and ammonium chloride based solutions were also trialled but proved less successful owing to their inability to mobilise metallic gold or gold cyanide species. Repetition of the transfer process proved capable of stripping 97% of the gold contained on the carbon fines for abed volume ratio of 6:1.

Jan 1, 2009

By Frank L. Hess

In 1876 cassiterite was identified in the placer gold from the northern Black Hills, and such a mixture could have come only from Nigger Hill or one of the streams draining the hill, because in no other hart of the northern hills have cassiterite anti gold been found together. Nigger Hill is in western Lawrence County, South Dakota, and on it is the little camp of Tinton. The Wyoming line runs along the west side of the hill and crosses the ridge which is the hill's continuation about miles north-northwest of Tinton.

Jan 1, 1938

"With millions of dollars and thousands of lives at stake, the Iron Ore Company of Canada (IOC) turned to a private wireless network for help.IOC needed a network that possessed the ability to adapt to changes in a nanosecond and to function seamlessly in the most rugged of environments.Canada’s largest iron ore producer required a private wireless network powerful enough to support all mine applications and deliver all data to one central point — without any existing cellular/3G/Wi-Fi coverage.Operations at IOC, a leading global supplier of iron pellets, involved dispatch, drill management and equipment monitoring, pump control and remote video that must service three distinct pits. Due to its setup, the facility does not offer a great deal of flexibility for transmitting signals.IOC serves a robust customer base made up of North American, European and Asian steel producers. It also employs nearly 1,900 people. Catastrophic death and destruction are two very real potential consequences of system communication failure.Technology for tough terrainKinetic mesh technology was born in the wake of the 9/11 terrorist attacks on the United States, one of the most high-stakes emergency situations in U.S. history. The failure of the communications infrastructure on a massive scale that day underscored the need for networking technologies that could provide service even in the most chaotic of conditions.Kinetic mesh networks allow organizations to deploy networks at sites where communications infrastructure has been compromised, as well as quickly establish networks in places where they did not previously exist. Kinetic mesh networks have also demonstrated a better ability to adapt to network changes on-the-fly versus other types of networking technologies."

Jan 1, 2015

By A Scott, A C. Torrance

Explosive properties are typically summarised on manufacturers’ technical data sheets. The values most commonly referred to are the density of the explosive, the energy it is expected to release and its velocity of detonation (VOD). This information is provided so that blasting engineers can make a considered selection of the most appropriate product for a particular blasting application. As an example, a lower VOD and energy product is better suited to blasting in soft, weathered material. In contrast, blasting hard, competent material generally requires a higher energy product which is usually characterised by higher VOD and energy.A review of the technical information supplied by manufacturers shows a wide range of methods of reporting both VOD and energy. A meaningful comparison between products from different suppliers is almost impossible to achieve based on these data. For a similar product, one supplier may have a VOD range of 2800–5800 m/s and a relative bulk strength of 1.34 while a corresponding product from another supplier is quoted with a VOD range of 3100–6300 m/s and a relative bulk strength of 192. In the end, the user has to rely on the level of confidence available from their experience using a certain type of explosive in the type of rock to be blasted at that mine.This paper reviews some of the technical and supporting information that is freely available in the literature and attempts to provide some clarity as to what the numbers that are reported actually mean for the end user. An alternative approach to the evaluation of the suitability of a given explosive to blast a given rock mass is proposed.CITATION:Torrance, A C and Scott, A, 2015. What is relative about energy?, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 447–454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The methods used by the Anglo American Corporation for analysis of long-term metal markets and prices are described. The principal factors affecting the relationships between production costs and metal prices are analysed. These are firstly the type of market, - speculative or consumer commodity, free market or subject to price control; and secondly the rate of growth of demand for the metal. It is shown that virtually all metals will have relatively low rates of demand growth for the foreseeable future, due to market saturation, increased economisation, substitution and product obsolescence. Metal prices have a clear dependance on production costs, however forecasting future costs is by no means simple; amongst other things, account must be taken of changing exchange rates, inflation rates, and the potential for operating more efficiently. The paper concludes by giving brief assessments of the long-term future for aluminium, copper, zinc, nickel and tin.

Jan 1, 1986

By William E. Ford, Edward Salisbury Dana

274. The PHYSICAL CHARACTERS of minerals fall under the following heads : I. Characters depending upon Cohesion and Elasticity - viz., cleavage, fracture, tenacity, hardness, elasticity, etc. 11. Specijic Gravity, or the Density compared with that of water. 111. Characters depending upon Light - viz., color, luster, degree of trans- parency, special optical properties, etc. IV. Characters depending upon Heat -viz., heat-conductivity, change of form and of optical characters with change of temperature, fusibility, etc. V. Characters depending upon Electricity and Magnetism. VI. Characters depending upon the action of the senses-viz., taste, odor, feel.

Jan 1, 1922

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By John V. Beall

Many Americans will judge the energy crisis by the picture shrink on their TV screen. And they are right to make this assessment considering the large areas of the country with marginal generating capacity, (See Fig, 1). The Federal Power Commission (FPC) recommends 20-25% reserve generating capacity above peak summer loads and 15-20% as minimal. The New York metropolitan area is the most concentrated power service area in the United States, and a spot check with Consolidated Edison, serving this area, revealed that on Friday, August 18, the company was operating at 5% reserve.

Jan 10, 1972

By Donald H. McLaughlin, Reno H. Sales

ADAPTATION to mining needs of the rich store of geologic knowledge concerning mineral deposits and the application of principles of the science to specific problems in the finding, development and stoping of particular ore bodies are the major tasks of the mining geologist. On him to an increasing degree is placed responsibility for estimation of ore and appraisal of mineralized ground, for explicit guidance of exploration and development, and for reliable advice with regard to the many geologic conditions that influence mining operations. In the long continued and steady efforts to meet these requirements, a special skill in close observation, recording, and quantitative interpretation has been developed, particularly by geologists on staffs of mining companies, which in many districts has proved to be effective, not only for technical ends, but also for advancement of scientific understanding. The foundations for mining geologic work were laid in most districts of the West by investigations of the United States Geological Survey. For years they have provided a reliable basis for geologic thought with regard to ore deposits, and later studies have enriched and supplemented rather than superseded them. In very few districts have the geologic relations stated in the earlier papers needed serious modification or revision, in spite of new evidence subsequently made available in abundance by mining exposures. Indeed, one of the chief satisfactions derived from success in mining geologic work is the assurance that it gives of the correctness bf the major concepts of the science of ore formation, established to so large an extent by the leaders of this notable group among whom Lindgren has been so eminent a figure. The geologists of the Survey have given and are continuing to give the service which can properly be expected of the Federal government. Their work, however, though of the greatest value in establishing the broad geological setting,

Jan 1, 1933

Mine planning for ore recovery by open stoping and pillar recovery is becoming more sophisticated, but there are basic operating constraints which must be imposed if this planning is to realise the production results on which the mine is dependant. The production reliability of an open stope is usually a high priority and common design problems can be identified. A range of practical considerations which should be considered at the mine planning stage are reviewed including equipment performance, blasting technology, ventilation requirements, development layouts, lead time, ground conditions, support, backfilling and ore recovery.

Jan 1, 1982

By Andy Hudson, Stuart Brashear, David Lilly

Because of greatly increased timing accuracy, electronic detonator systems are a well-known and widely accepted major tool to control and reduce ground vibration. At a Southeastern quarry the authors found that the use of electronic detonators improved the reliability of the well known cubed root scaled distance equation for determining air blast. In addition, the authors noticed significant correlations between selected major peak particle velocity frequencies and air blast magnitudes. The major peak particle velocity frequency alone is a close approximation to air blast magnitudes. This relationship is not as significant or not always evident when standard pyrotechnic initiation systems are used.

Jan 1, 2009

The influence of Harold Hotelling?s work in the field of mineral economics is both unusual and outstanding. In the 66 years since its development, theory surrounding the economics of exhaustible resources has only been significantly researched since the early 1970s. At that time a wave of research into the economics of exhaustible resources arose from the threat of global resource scarcity and continued into the late 1990s. Current East Asian and global demand for natural resources as well as mineral and metal commodities, has stimulated interest in the optimal and sustainable exploitation of exhaustible resources to the point that the subject is worthy of review. Hotelling?s theory and the assumptions that he made in establishing a model for the optimal exploitation of mineral resources at the industry level and at the level of the individual mine owner, are examined. He showed that the rate of increase inexhaustible resource prices should be equivalent to the market rate of interest and that in a market with rising prices the rate of extraction should be constant. In markets where demand is stable optimal exploitation requires that the rate of extraction should decline over time, while in a monopoly market he showed that the rate of extraction is retarded. In addition, the effects of cumulative production on costs and prices, the uncertainty associated with estimates of the resource stock, the impact of exploration and issues of intergenerational equity are examined. An analysis of the optimal price path, extraction costs and mineral rents at an industry level is presented as a model. An analysis of the rates of production and optimal benefits at the individual mine level including total, average and marginal costs on the optimal rate of production, is considered. Optimal extraction rates for a mine with a clearly defined concave positive cost equation vary according to the position on the marginal cost curve. The influence of discount rates and the size of the ore reserves on the rates of mineral extraction are also examined and could define the frontier of usefulness for the ?economics of exhaustible resources?.

Jan 1, 2007

If problems are opportunities in disguise, the mining industry certainly had plenty of "opportunities" in 1975. Considering the industry's generally lackluster 1975 profit record, and in view of the slowdown in inflation, there's some hope that 1976 might be a better year in spite of the increasing risks and uncertainties that plague the mining industry.

Jan 2, 1976

By Ken Barish

Jane Mine of the Keystone Coal Mining Corporation was started in 1962 and is in the Lower Freeport seas located in Armstrong County, Pennsylvania, approximately 45 miles northeast of Pittsburgh. The mine is a slope/shaft complex with the cover ranging from 100 feet at the slope to 450 feet near the back end of the property. The seam height ranges from 48 to 72 inches. A variety of roof conditions have been en¬countered, and an equal variety of roof control systems have been tried with varying degrees of success. Initially, places could be mined as deep as 100 feet without any permanent roof support. After several problems and the advent of the Health and Safety Act of 1969, roof control became more and more prevalent and predominant at the Jane Mine. It started with 4 foot conventional oolts. As the mine progressed in the northeasterly direction, roof conditions changed from the extremely good roof that was encountered initially, to bad roof; and other types of roof support were required. Sixty pound rails and 6 inch 25 pound to the foot steel I-beams were used for supplemental support in long life headings such as belt and track. Resin bolting was done in many areas for long life support due to the deterioration of the shale roof over time. Several areas had to be abandoned because of uncontrollable top.

Jan 1, 1984

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written that aid in the design process in the academic arena and should also have industrial applications. The programs described include a drag-line cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program, and an overburden volume and coal tonnage sequencing program.

Jan 1, 1988

By G Stanway, P Mahoney, C Griebel

The Mining Innovation – State of Play was initiated three years ago by VCI in partnership with the University of Western Australia. The ambition was to create a ‘think tank’ type platform to support industry discussion on how it is performing in terms of innovation at a strategic level, what needs to change in the industry ‘ecosystem’, and how businesses may more effectively develop their strategy and architecture to innovate for competitive advantage.The drivers for this ambition were straightforward. The industry recognises itself as being conservative with respect to innovation and it knows the business and community endowment dividend from getting better at innovation is large; however, much of the material that seeks to provide insight on innovation tends to be drawn from industries that do not have the same high capital, long life cycle and market uncertainty characteristics as that faced by mining. Material that does focus on mining innovation is orientated towards technical innovation, not innovation strategy. There exists a significant knowledge gap, and filling it is valuable to both mining businesses and communities.The 2014 Mining Innovation State of Play report (Stanway, Griebel and Mahoney, 2014), based on a survey of over 230 mining executives, uncovered a range of insights but left several questions unresolved. The people with the best perspective on these questions are CEOs. They can see the business issues with sufficient clarity and have the influence to shape both the industry and its organisations, as seen in Figure 1. Discussing these questions with the view to progressing our collective understanding was the primary reason this interview series was conducted.Unsurprisingly, interviewing 15 CEOs and Chairpersons from different industries and commodities, across the globe resulted in a broad range of views. The discussions were frank and often blunt in assessing the short comings in the industry and suggestions for improvement. This degree of candour is hugely valuable as a basis for improvement. In the end, four key areas emerged as a basis for improvement.CITATION:Stanway, G, Griebel, C and Mahoney, P, 2017. Mining Innovation State of PlayTM – iron ore insights, in Proceedings Iron Ore 2017, pp 439–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007