Search Documents

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By M. Rieber

In July 1985, as the U.S. copper industry contracted and the Mexican industry expanded, a trans border pollution agreement was signed which included smelter air pollution control in the "Gray Triangle": Cananea, Nacozari and Douglas. Since then the Douglas smelter has been closed, a year earlier than initially required; though its new smelter is operating, S02 collection and acid disposal at Nacozari is yet to come; and the Cananea smelter has been un-touched. Nacozari and Cananea copper mining have expanded while a reduced U.S. copper industry has rationalized to a point of fragile profitability. As a paradigm of U.S. copper competitiveness, this paper attempts to explain the differential fortunes of copper in the two countries, to project the future of the smelter agreement as a function of acid disposal, and to consider the consequences of the politicized application of smelter pollution control in Arizona.

Jan 1, 1988

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By T. Marsden

The demand for continuous improvement in the industrial world is an ongoing process. Some sectors, where the competitive forces are well established, have led the development of new and reliable technological innovations. Although the metallurgical industry can rightfully be proud of its process improvements, there is still work to be done in materials and in material handling. In some cases, the improvements will be as simple as adopting technologies that have been perfected in other processing or manufacturing industries. This paper discusses the next design generation for copper tankhouses which will yield: ?Improved copper quality ?Improved equipment availability ?Lower life cycle costs ?Safer operations. These benefits will be realized through new developments and design improvements in: ?Permanent cathodes ?Cathode washing ?Cathode stripping machines ?Anode preparation machines ?Improved lead anode design ?Recycling of lead anodes and refurbishment of cathodes. The demand for base metals, and in particular copper, has led to more research into improving efficiencies in electrowinning and refinery plants around the world. One of the areas previously taken as a matter of course was the production of lead anodes and stainless steel cathodes. In South America alone there are over 600 000 cathodes and anodes in circulation?a very significant figure.

Jan 1, 2009

By Rodger Fry

All coal deposits contain anomalous geologic conditions which have an impact on roof control, Run-Of--Mine (ROM) coal quality and production costs. To remain competitive in today's coal market and provide a safe working atmosphere, mine operators need to know in advance of mining the geologic conditions which prevail in the coal deposit. In order to identify geologic anomalies within a coal seam and surrounding roof rock in advance of mining, the Radio Imaging Method (RIM) survey procedure has been developed. This paper describes the RIM procedure and how it is used to predict various geologic conditions within a coal deposit. Figure 1 illustrates the RIM in-mine and surface surveys which can be used in an underground mine. [ ] RIM is an electromagnetic (EM} wave process which consists of in-mine and surface survey techniques. Both techniques are used in underground coal mines to detect faults, interbedding, sandstone channels, and thinning coal. Thesurface survey can also be used to determine seam correlation and continuity in strip and underground mining. In-mine and surface surveys work by propagating EM waves along straight paths through the coal. As the RIM signal travels along a ray path, it interacts with the seam material and surrounding rock. This interaction causes the signal to lose energy thereby decreasing its strength along the path. The amount of energy loss per unit path length depends upon the coal seam height and type of surrounding roof and floor rock. A reading of the signal level is taken at the end of the ray path at the receiver location. This reading is used to determine the loss (attenuation) rate of the signal along the path. The signal level data is compiled and analyzed through computerized algorithms which construct images of any anomaly present. This graphical depiction of the coal provides a basis for further geologic interpretation. By comparing the images reconstructed by the RIM analysis to in-mine geologic mappings made while mining through RIM study zones, it has been confirmed that RIM can help detect the following; Rapidly Thinning Coal Incompetent Roof Rock Poor Floor Lithology

Jan 1, 1984

By Guy Jordan

HIGH-IRON cements have a number of advantages over cements carrying little or no iron. The presence of iron in, Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to freezing and thawing, and increases the resistance of the cement to sea or sulphate waters. During the past few years the construction of numerous dams through-out the Southeast by the Tennessee Valley Authority has stimulated the production of high-iron cements. At present a great number of specifica-tions call for an iron cement, and the industry is supplying this demand with a Portland cement carrying approximately 5 per cent iron oxide. Several manufacturers are now making practically all of their cement of this type and a number of others manufacture it as a special cement over short periods to meet demands from the Tennessee Valley Authority and other buyers. The recent increase in the use of iron in Portland cement has created a market for iron products that previously was nonexistent. The chief sources of supply for the cement manufacturers at present are iron sand, iron sinter and slag, and ocher. The Copperhill mining district, Ten-nessee, supplies both iron sinter and slag for use in cement. The Carters-ville district supplies iron sand, ocher, and some iron resulting from the magnetic separation of iron from barite. The advantages of these products vary according to the chemical properties of the raw materials and the methods of handling used by the different manufacturers. Where the iron is to be handled by conveying belts and in hopper cars, the iron

Jan 1, 1939

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By M Ruhrberg, J Grassmann, C Bauer

Within the context of acid mine drainage (AMD) associated with mining activities worldwide there has been a tremendous research effort to determine the extent of AMD and assess the influencing factors controlling this process. However, the majority of the current approaches focus on local and regional scale case studies and do not provide a global scale picture of AMD potentials. This study attempts to develop a method aiming at a global environmental impact assessment related to AMD. To confine the complex topic this study concentrates on acidic emissions from heaps in consequence of copper mining processes. In order to pursue this approach two factors are of significant advantage: a comprehensive environmental data base of more then 600 copper sites worldwide and a method which has been developed and proven to be successful in assessing environmental impacts related to land use. Current and future research efforts focus on using this background knowledge to enable both a comparison between sites and a categorisation of sites according to emission estimates.

Jan 1, 2003

By John D. Ridge, Robert C. Barwick

The quantities and destinations of the metallic ores and concentrates and partially or fully refined metals in international trade result from the interaction of many factors, of which geographic location is only one. How far the processes of concentration and refining are to be carried in the country in which the mining is done and what dictates the destinations to which the more or less completely processed raw materials will move are determined not only by present-day geologic, political, and economic conditions, but also by the patterns set up by these same conditions as they obtained in the past. The first generalization that can be made regarding trade in metal raw materials-one that affects the form in which the material is transported, rather than the patterns followed by that trade-is that concentration is carried out for all low grade ores, nonferrous or ferrous, in the country in which they originate. (Rule 1.) Economic considerations alone almost always require that this be done; only high grade iron, manganese, and chromite ores can be shipped as they are mined.

Jul 1, 1955

By Fabio Santillan, Michael F. Zoccola

"Wolf Creek Dam and Lake Cum berland in Russell County Kentucky is operated by the United States Army Corps of Engineers (USAGE) Nashville District It is a combination 3,940 ft long (1,200 m) non-zoned clay embankment, a maximum of 215 ft (65.5 m) above top of rock and 1,796 ft long (547 m) concrete gravity section. Built in the 1940s, the limestone beneath the embankment is characterized by an extensive interconnected network of solution feature; varying from fist size to largecaves.In 2005, studies conducted by the Nashville Distrect concluded that a new seepage cut-off wall was needed as the existing cut-off wall, installed in the 1970s, did not go deep enough and did not extend laterally far enough to intercept all major karst features The dam was classified as a ""Dam Safety Action Classification I (DSAC 1) – Urgent and Compelling,"" the highest risk under USAGE risk category rankings. Also in 2005, under a USAGE risk screening program of its entire dam portfolio, Wolf Creek was classified as a Dam Safety Action Classification 1-Urgent and Compelling, which put it in the highest category. In 2007, an Independent External Peer Review from outside USAGE, concluded there was compelling evidence that a piping failure mode had re-initiated and was in an ""advanced continuation"" stage of development.Impounding approximately 6 million acre-ft (7.4x102m3) of water at flood storage, Lake Cumberland is the largest reservoir east of the Mississippi River and ninth largest in the United States. Catastrophic failure would result in widespread flooding, Ices of life and economic losses in billions of dollars.In 2008, the Nashville District partnered with a joint venture between finns Treviicos and Soletanche (ISM through a ""Best Value"" contract to construct a new seepage barrier wall. This acquisition method was used in lieu of a low bid contract due to complexity of the work and dam safety concerns. It took advantage of the experience and innovation of contractors by soliciting technical proposals that were evaluated independent of cost. Those proposals deemed technically qualified and responsive then underwent a trade-off analysis between ccst and technical approach and a selection was made of the one deemed to give the best combination."

Jan 1, 2013

By Joseph Kittredge

AT the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Pa., using fuel oil, then costing about 2 ½ ¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulveriz-ing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation.

Jan 1, 1939

Jan 1, 1930

By Earl L. H. Sackett

Barite, although not a glamour mineral and probably little known to many of those in the mining business, is produced in the US. in very respectable quantities and is an important factor in the mineral economy of this country. The scope of the various uses of this mineral is perhaps one of the most misunderstood things about it, for it is surprising how many of those with a casual knowledge of the subject speak of its primary utilization in terms of paint pigments and barium chemicals. The life blood of barite utilization, however, is the petroleum industry by virtue of its dependence on this high specific gravity, inert mineral as the weighting material in its drilling fluids. From 80 to 85% of barite usage in the U. S. is accounted for in this manner-in fact, its role in oil well drilling is the only excuse for some of the large-scale barite production facilities which have been developed. Other uses are important and widely varied, but comparatively they are of small scale. They include fine crushed barite of low iron content as a component in glass manufacture, barite as a source material for manufacture of barium chemicals, finely divided barite as a component of some rubbers and ground, bleached barite in pigments. The formerly substantial use of barite in lithopone, however, has declined markedly because of replacement of lithopone by titanium pigments

Jan 5, 1962

By M. B. Ramachandra Rao

THE occurrence of copper ores at Garimenapenta, 14° 59 min 30 sec N Lat., 79° 33 min 10 sec E Long., in Nellore district, Madras State, India, has been examined and investigated on numerous occasions during the past two centuries.1 No tangible orebody was ever located as a result of all the ex-

Jan 4, 1953

By Seth C. Schaefer

The Bureau of mines investigated thermodynamic properties of MnSO4 and 2CdO CdSO4 to obtain basic thermodynamic data applicable to the treatment of mineral concentrates during roasting and sintering processes. Standard Gibbs energies of formation were determined with high-temperature galvanic cells using stabilized Zr02 as the electrolyte. Potential measurements were obtained from the cells?

Jan 1, 1983

By Nielen van der Merwe

Mr Janisch' s comment' in the August issue on Dick Stacey's remarks about safety factors indeed requires wider debate. The example he quoted to illustrate the successful application of the safety factor concept in coal mining, namely the Salamon formula, is to my knowledge the only recognized application of that concept. Not only that, but that particular formula should be used only for what it was intended, namely to prevent major disasters. It was never intended to indicate long-term pillar stability, and it should not be used for that.

Jan 1, 1993

In the UK as existing face capacity is replaced, many of the new faces will have higher installed powers and be located in zones of higher strata temperature. These factors coupled with the need to increase production will result in more faces experiencing environmental difficulies, especially with respect to climatic conditions. In many cases these problems are unlikely to be solved, as in the past, by simply increasing the face air quantity. Therefore other techniques including refrigeration will be necessary, possibly requiring major capital and operational expenditure. It is easy to spend large capital sums and incur high operational expenditure without achieving the desired amount of climatic control. There is therefore a great need for reliable prediction techniques to aid in the making of sound, informed decisions which will have a significant influence in the long term on the level of production costs. A computer program able to predict the heat flows and resultant climatic conditions on a long¬wall coalfaces has been developed. Throughout it's development underground measurements have been used to validate the computer model and it has been shown that for an advancing coalface under normal production conditions that the program predicts the climate to within 1°C of the measured conditions. This paper outlines a number of methods available to improve climatic conditions on longwall faces. The coalface temperature prediction program is used to quantify the effects of these methods on the climatic conditions for a model coalface and a comparison is given. In conclusion a cool¬ing strategy for longwall faces is outlined.

Jan 1, 1991

By G. Deschênes

"In 2013, as the prices of precious metals dropped, investors moved their positions to equity markets for higher returns. As a result, the price of gold dropped further to below US$1200 per ounce, prompting additional substantial outflows from gold investments. In response to lagging gold prices, major gold producers initiated large asset write-downs and cost-cutting programmes. In 2015, this trend continues and gold mining stocks are close to lows not seen since the global financial crisis (GFC) of 2008. In the current economic climate many projects have marginal economics, and the number of projects that have competitive development and production costs is declining. A competitive edge is particularly important with the decreasing grades of orebodies, increasing complexity of the mineralogy, and increasingly demanding environmental constraints. In addition, higher cost producers seek to optimize their process t o reduce operating costs.This paper presents some highlights of three case studies on optimization of gold leaching strategies that improved the economics of brownfield projects. Processing of sulphide-bearing ores was optimized by using the synergy between cyanide, lead nitrate, and oxygen. The outcomes were significant reduction of retention times while maintaining or increasing gold extraction and reducing cyanide addition and effluent treatment costs. A stirred tank reactor experimental programme led to direct implementation of reliable leaching strategies from laboratory scale to production. This approach resulted in savings of $2.2 million to $15.2 million on the three brownfield projects discussed in this paper."

Jan 1, 2016

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By C. Díaz

Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulfur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is heated in a sulfuric acid plant, and the low sulfur calcine is reduction smelted with coke in an electric furnace to yield a sulfur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulfur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries are obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters.

Jan 1, 1993