Search Documents

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

By Robert Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultimate cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development.

Jan 9, 1926

By K. E. Stanfield

Oil-yield results are presented for 65 oil-shale sections in Piceance Creek Basin, Colorado, sampled during the period 1957 through 1963. Including previously published data, oil-yield results for 203 sampled sections have now been released by the Bureau of Mines to aid in appraising the shale oil potential of the basin. Oil yields of core samples (135 sets) were regarded as reliable bases for appraising the Mahogany-zone interval, but only 5 sets of cores sampled the deeper, lower-zone oil shales. Drill cuttings (68 sets) sampled the lower-zone oil shales, but their oil yields are principally indicative and should be confirmed by analyses of cores. More complete core sampling of the lower-zone oil shales is needed.

Jan 1, 1967

Risk management has become an essential tool for mining companies to ensure their projects are well-managed and profit expectations are achieved. Risk management has also become a mandatory corporate governance requirement in Australia for publicly listed companies and equally important to attract investors. This paper provides a brief overview of the essential tools needed to implement a practical risk management framework to comply with the internationally recognised ISO 31000:2009 risk management-principles and guidelines from the perspective of small or soon to be producing mining companies. To?successfully?deal with the unknown and to manage the opportunities and risks involved with a mining project requires a clear understanding of the basic risk management principles. These include how to develop a project risk register, how to develop a project risk treatment plan and how to manage and monitor project risks to take full advantage of the opportunities presented.The first step is to identify and fully appreciate the risks that face a mining project. There are many risk identification methods that can be used including checklists, brainstorming and hazard and operability (HAZOP) studies. These often lead to a telephone book full of risks which are near to impossible to manage. A risk library specifically designed?for mining?projects containing no more than 100 risks will cover the major showstoppers, is practical and can be readily implemented and successfully managed.A risk framework also needs to be established which is compatible with the companyÆs structure and objectives. Once each risk has been assessed in regard to consequence and likelihood and the risk control systems are in place they need to be assigned to the responsible manager. The extreme or high risks will require a risk treatment plan to be developed. Risks will change during the life cycle of a mining project. Hence, a reliable monitoring system is also required for compliance.CITATION:Jones, J A, 2012. Mine project risk management, in Proceedings Project Evaluation 2012 , pp 117-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Clinton O. Rex, Adam S. Hurley, W. Morgan NeSmith

"Hartsfield-Jackson Atlanta International Airport underwent a $1.2 billion dollar expansion project centered on the construction of the new Maynard H. Jackson International Terminal. Passenger access between the new International Terminal and the domestic airport facilities is primarily via underground Automated People Mover (APM) trains. Prior to this expansion, the APM tunnel terminated beneath Concourse E, which previously served all international flights. The new International Terminal is located approximately ½-mile from the previous terminus of the APM tunnel.A paper describing the general approach to excavation support for construction of the entire APM tunnel extension from under Concourse E to the new International Terminal was published by two of the authors (Hurley and NeSmith, 2014). One of the features of note of the approach involved the intersection of the proposed new alignment of the APM tunnel extension under Concourse E with the old terminus. Specifically, the new tunnel extension conflicted with the location of the existing Auger Pressure Grouted (APG) piles supporting four columns in Concourse E. This paper presents design and installation details of the micropile underpinning approach used to support the existing columns to allow for the proposed excavation including the cutting and removal of the existing APG piles, while allowing Concourse E to remain in service during construction.PROJECT DETAILSGeneralThe construction of the APM extension required an excavation support system for a 450-ft long, 55-ft deep excavation across Taxiway Dixie and a 900-ft long, 30-ft deep excavation beneath the basement of existing Concourse E. The excavation under Concourse E required both excavation support and support of the existing columns over the proposed excavation zone. A general overview of the work area is shown on Figure 1."

Jan 1, 2017

By J. M. Singer

Methods are proposed for predicting concentrations of nitrogen oxides and carbon monoxide in the combustion gases of flames, specifically of lean, stoichiometric, and rich propane-air flames. Calculations are based on kinetic and thermodynamic theory. These theoretical data are compared with concentrations observed experimentally downstream of flat grid-type burner flames (approximately 25,000 Btu/hr) that were used to simulate gas appliances such as water and space heaters. Air pollutant concentrations are also computed for (1) flames chemically perturbed by recycling flue gases into the primary fuel-air mixtures; (2) flames thermally perturbed by cooling the burned gases at different rates; and (3) flames perturbed by combination of these two effects. In general, experimental and computed concentrations agree to within a factor of 2 to 7 with the experimental values always being higher than the theoretical. The theoretical analysis indicates that cooling the primary flame by recycling cold flue gases (with and without excess air) reduces the relative emission of nitric oxide and increases emission of carbon monoxide if the flame stoichiometry does not radically change. Cooling rates of about 5,500° to 10,000° R/sec starting at about 3,500° R generally suffice to prevent nitric oxide concentrations in lean flames from increasing much above the initial values at the combustion zone; these same cooling rates do not prevent oxidation of most of the initial carbon monoxide.

Jan 1, 1967

By H. Utsunomiya

Most magnesium alloy sheets show low deformability in rolling. Edge cracks and transverse fractures are common difficulties. In addition, rolled sheets show well-developed basal texture <0001>//ND. The texture causes high anisotropy in mechanical properties and low formability in subsequent metal forming. Differential-speed rolling, where the upper and the lower rolls rotate at different speeds, introduces shear deformation through the thickness. Not rolling texture but shear texture evolves in the sheet so that the asymmetric rolling can be a method of texture control. However the primary slip system of the hcp alloy, is basal, the shear texture should be also basal. Differences between the two basal textures, i.e., the rolling texture and the shear texture, have not been understood completely. In this study, conventional (same-speed) rolling and differential-speed rolling have been applied to commercial AZ31B sheets at 623K. Microstructures, textures and mechanical properties of the rolled sheets before/after annealing are compared. It is found that the basal texture is more pronounced by the asymmetric rolling. On the other hand, the asymmetric rolling is effective to decrease the grain size and the planar anisotropy.

Jan 1, 2006

By S. Katz, M. E. Nicholson, J. J. Kelly, D. R. Curran

A series of wedges of 1020 steel (2 1/2 by 6 by 8 in.) were explosively loaded, as shown in Fig. 1. A slab of explosive on the surface of the steel wedge was initiated simultaneously along one edge, producing an essentially two-dimensional oblique shock in the metal. Pressure and density in the metal were measured as a function of distance from the explosive-metal interface by a method described elsewhere.&apos; While for pressures below 130 .kbars the technique produces accurate results, for greater pressures the presence of two shock waves in the metalzy3 makes interpretation of the data uncertain. However, the location of the transition in pressure at 130 kbars can be readily identified from the data. The assumption of a single shock in the region above 130 kbars overestimates the pressure computed on a multiple-shock model. After firing, the wedges were sectioned, lapped, and etched with 2 pct Nital. A photograph of an etched specimen is shown in Fig. 2. The specimens were examined metallographically. The dark region, at the top of the specimen, was heavily banded, Fig. 3, while the lighter area was comparatively free from banding, Fig. 4, the boundary between the two regions being quite abrupt. The very light regions at an angle of about 45 deg to the explosive-metal interface show virtually no banding. The origin of these light regions, which are not Luder&apos;s bands, is not yet explained. The thickness of the heavily banded area was measured and compared with the pressure at the boundary between the heavily and lightly banded regions. The results of these measurements and calculations are given in Table I. For all shots, the pressure at the boundary is approximately the same

Jan 1, 1960

By John E. Murphy, Ernest L. Ohle

Hematite-magnetite ore bodies at Iron Mountain, Missouri, have produced nearly 9 million tons of iron ore concentrates since 1844. The ore minerals occur principally as open-space filling in fractured and brecciated andesite porphyry with very minor replacement of the wall rocks. The enclosing rocks are Precambrian in age and consist of a series of dacite, rhyolite, and andesite flows aggregating about 2000 feet in thickness. All of the ore is in andesite and the mineralization is Precambrian in age. The shape of the ore bodies, the breccia character of the ore, and the gangue mineralogy are believed to be unique. One of the two main ore bodies is crudely dome-shaped with a tendency for development of concentric mineralized shells; the other is an elongated lense in plan but hook-shaped in cross section. Both have strong linear elements striking northeast, east-west, or northwest. Various modes of origin for the structures and for the tension breccias have been suggested, but none is completely satisfactory. Hematite is the main ore mineral; magnetite is subordinate. Important gangue minerals are andradite, quartz, calcite, actinolite, apatite, epidote, and chlorite. Although some evidence favors injection of an iron-rich melt, other evidence suggests ore formation by a high temperature, water-rich solution.

Jan 1, 1968

By W. E. Newell

The basic principles and assumptions involved in D. L. White&apos;s solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.&apos; In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-&apos; and semi-conductor, and current saturation in piezoelectric semiconductors.&apos;4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By William F. Riggs

The characteristics of frothers can often be determined by the proper selection of various chemical groups. There are three basic groups utilized in the application of frothers. These are alcohols, polyglycol ethers, and polyglycols. Some of the chemical groups are separated in subgroups. Each chemical group provides particular characteristics which affect load support, bubble diameter, water retention, air dispersion, and kinetics of froth formation. These chemical groups may be preblended in various percentages to optimize frother characteristics for a particular ore deposit.

Jan 1, 1986

By Kliment Y. Hakobyan

A new technology for treating molybdenum sulfide concentrates has been developed. It includes roasting the concentrate in a special regime with water vapor, cooling and neutralizing exit gas, oxidation roasting of rhenium containing MoO2, and the extraction of rhenium from exit gases. This technology allows economically efficient and environmentally safe processing of molybdenum concentrates: The degree of molybdenum extraction is 98.8%, rhenium-90%, sulphur-98.4%. The technology also ensures high extents of extraction of selenium and tellurium as well as the fixation of sulfur in the form of sodium sulfide or elemental sulfur.

Jan 1, 2006

By Edmund S. Leaver, Jesse A. Woolf

"The Baboquivari mining district is about 60 miles southwest of Tucson, Ariz., the present railroad shipping point. The values are silver and gold. The silver is largely associated with the black oxides of manganese. The ore is highly oxidized, and careful panning shows only a very small amount of pyrite. Our sample analyzed as follows:A flotation mill has been installed in the district, but it does not concentrate the precious metals satisfactorily. Our best laboratory flotation results were obtained by grinding to pass 65-mesh and floating with Xanthate or standard flotation oils plus sodium sulphide and polysulphide. This sulphidizing method gave a concentration of 32 per cent of the silver and 80 per cent of the gold, which about equals plant practice.We do not know of an instance where the oxidized forms of manganese have been concentrated satisfactorily by flotation.Plain cyanide on the original ore extracts practically all of the gold but only one-third of the silver. A preliminary deoxidizing roast, using producer gas or powdered coal, gives a calcine from which cyanide dissolves about 90 per cent of the gold and 75 per cent of the silver. This method of treatment, known as the Clevenger-Caron process, is described in Bureau of Mines Bulletin 226.Preliminary treatment with sulphur dioxide by burning pyrite or sulphur and passing this gas into the pulp until all of the contained manganese is dissolved or changed in form best prepares the ore for cyanidation. The acid consumption will vary with the percentage of manganese and other soluble constituents. Neither gold or silver is dissolved by this acid treatment. The washed residue gives maximum cyanide dissolution of the gold and silver with minimum loss of cyanide,"

May 1, 1928

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By Zbigniew Zurecki

The selection of atmosphere composition is critical for controlling surface quality of reactive aluminum alloys during solution treatments. An improper selection of annealing atmosphere can result in surface blistering in AI-Mg and sub-surface depletion of lithium in AI-U ingots. To determine optimum atmosphere compositions for homogenizing A1-Mg and Al-Li alloys, Ii number of exploratory experiments were carried out in air, nitrogen, and carbon dioxide based atmospheres including reactive impurities or additive such as moisture and sulfur hexafluoride. This paper describes the influence of these atmospheres on high-temperature oxidation and sub-surface defects. The results are discussed in terms of the change in Pilling-Bedworth ratio.

Jan 1, 1996

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By J. L. W. Birkinbine

This paper is a discussion of a part of the mineral wealth of the States of Oaxaca and Paebla, Mexico. It does not refer to the precious metals, sonie mines of which, in these States, are said to have been worked before the advent of the Spanish conquistadores in the sixteenth century, as my purpose is to invite attention to the exploration of deposits of coal and iron-ores in the Mixteca region. The prominence given to coal is warranted by the great effect of the scarcity of fuel upon the industrial development of Mexico. Under the progressive administration of President Porfirio Diaz, the Republic has made wonderful advances in the past three decades; and this progress would have been greater but for the limitations imposed by expensive fuel. In the spring of 1906 I was detailed by the Birkinbine Engineering Offices, of Philadelphia, to accompany A. B. Adams, of New York, in a reconnoissance of reported deposits of iron-ores in the State of Oaxaca. The result of this expedition was the formation, in 1907, of the Oaxaca Iron & Coal Co., of which Mr. Adams became, and has remained, President and General Manager, and I have spent the past three years as Chief Engineer of this company in Mexico, principally in western Oaxaca, where field-headquarters were established. GEOGRAPHY AND POPULATION. Although the geographical and topographical features of the Republic of Mexico are well known, few realize that the majority of its population is domiciled in the States which immediately surround the capital city of Mexico, including the Federal District, Mexico, Tlaxcala, Morelos, Puebla,

Jan 1, 1911

By Kiyoshi Mizui

Processes for manufacturing prereduced iron pellets from iron ore dust occurring in iron works have recently begun on an industrial scale. Because of their high porosity and low mechanical strength, these prereduced iron pellets tend to oxidize again and disintegrate into fine particles during transportation and storage; this may result in such difficulties as decreased yield, undesirable work environment and heat generation during oxidation. A possible process for avoiding oxidation and disintegration of prereduced pellets is increasing the density through briquetting. The authors carried out briquetting tests under various conditions, attempting to find optimum briquetting conditions. They found that crushing prereduced pellets and adjusting the particle size to a certain range before briquetting increased the briquette strength and reduced the amount of binder needed. Oxidation resistance of briquettes and raw material pellets was compared in open air and at high temperatures. Briquettes showed superior oxidation resistance.

Jan 1, 1977

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

By Wolfgang H. Roth, Stephen J. Navin, Samuel K. Louis, Anthony F. Stirbys

This paper presents a case history of the design and construction of the access shaft and cross adit utilized to gain access to the Los Angeles Metro Rail tunnel alignment, at the A146 Contract site. The access shaft, a 14 m (45 ft) inside diameter structure, was constructed using ring beams and lagging with concrete backfill to a depth of 18.59 m (61 ft). The cross adit was hand excavated in sequential benches using liner plate, arch ring beams, and posts for support. The sequence of excavation and support placement are discussed. Soil conditions encountered at the project site are discussed together with the development of the design criteria. Instrumentation data collected during the excavation are also presented.

Jan 1, 1989