Search Documents

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By J. J. Carlson

An important factor in filtration is the zeta potential of the particles. Since zeta potential is a function of pH, it was hypothesized that adding CO would lower the pH and zeta potential. A reduction in zeta potential should enhance the flocculation and increase the filtration rate. This paper describes the effects CO on the zeta potential of both pure hematite and samples of hematite concentrate from an iron ore processing plant. A significant shift in the zeta potential, as a function of pH, curve was observed. These results point to an alteration of the particles mineralogy, not just a shift in pH.

Jan 1, 2010

By R. B. Inturi, R. G. Reddy

Solid-state reduction of roast Movat chromite ore with carbon was carried out as a function of the C/FeO ratio at temperatures ranging from 800°C to 900°C. The reduction was studied using thermogravimetric analysis (TGA). A two¬stage mechanism consisting of the reduction of FeO with carbon monoxide and the regeneration of CO by the oxida¬tion of carbon with CO2 was proposed. The rate-controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55,800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 2000

By Manfred G. Raschke

INTRODUCTION In the past decade, the international coal trade has been undergoing a period of gradual change. This change will continue through the remainder of this century until by the year 2000 the international coal industry will look very different from the industry which existed in the early 1970's. The industry which will emerge from the thirty year period of change (1970-2000) will be different in many ways. -The volumes of coal transported will be much larger. - The primary type of coal traded will be steam coal rather than metallurgical coal. - A much broader group of countries will be participating in the trade both as suppliers and as consumers. - The trade will be dominated by a relatively small number of large producing and trading companies. - The coal mined for international shipment will be primarily surface- mined. – The United States will play a decreasingly important role in international coal trade. In the course of this paper I propose to address three questions which are crucial to the formulation of an understanding of the changes outlined above : (1) Which supplier nations will be most successful in the international metallurgical and steam coal trade in the next decade and a half? (2) What emerging trends will shape the international coal trade in the 1980's and 19901s? (3) Where are U.S. producers likely to fit in this scheme of things? As a background to my remarks, I should note that what follows is based on five years of work in a consulting capacity on coal supply and demand issues worldwide. Although in the course of this work I have had occasion to develop mining and transportation cost figures for all of the countries discussed below--both my own and those obtained from coal producers--it is apparent that success in the marketplace can be determined in some instances by considerations other than costs. Nevertheless, my comments today about international competitiveness will be dominated by cost considerations; there are, after all, not many markets that reward the high-cost producer with success. Let us begin by establishing some criteria for success in the international coal market and then compare some of the producer nations to some of these criteria. The criteria are: - Low delivered cost, - Good quality coal, - The producer's partnership in a joint mining venture with an importer or a consumer of coal, - The producer's international business orientation and commitment to penetrating the market, - The producer's reliability as a supplier, and - Political pressure exerted by the producing country on consumers.

Jan 1, 1986

By M. Ge, C. Mborah

"The acoustic emission/microseismic monitoring (AE/MS) technique has widely been used in the mining environment for the monitoring of rock mass stability. A successful implementation of the method is hinged on being able to accurately determine the P- or S-wave arrival which is then used in the determination of the source of an event. Determination of the arrival phase is usually performed visually by a human expert. However, the mining environment is characterized by high noise levels and different noise types of varying intensities. Therefore, performing manual phase picking on time series data acquired from the AE/MS monitoring system can sometimes be tedious and time consuming if not impossible. In this paper, a proposal for improving manual P-wave phase arrival picks is discussed. The method involves the filtering of the AE/MS data using a stationary discrete wavelet transform (SDWT) method. After filtering, appropriate scales/levels of the multi-level decomposition process are then selected for further processing. The first step in the picking process after filtering, requires the computation of the signal power and the root mean square (RMS) using the signal amplitudes at each scale. The preliminary P-phase arrival time is picked using the results of the calculated power and RMS values respectively. The calculated RMS values are then superimposed on the calculated power values to determine the final arrival picks. If the arrival time picks obtained by both methods coincide or are within 5 to 10 sample points, the pick is considered reliable. The accuracy of the method was verified using AE/MS data from two datasets obtained from two separate underground mines. The results of the study showed that the picking method is reliable and robust. Based on the data studied, it can be concluded that the method will help reduce the time usually spent in processing AE/MS data from mines. INTRODUCTION A successful identification and location of the source of acoustic emission/microseismic (AE/MS) events is mainly dependent on the onset time of the P-wave phase. In many seismic networks, initial picks are performed by picking algorithms followed by manual picks by human experts. If the waveform signal-to-noise ratio (SNR) is low, the P-wave onset time picks by the human expert is generally reliable and accurate [1]. However, for waveforms with high SNR, picking of the P-wave onset could be a major challenge. Also, due to the volume of data acquired daily, manual processing could be stressful and time consuming [2]. These challenges continue to provide motivation for alternative means of providing reliable and efficient ways of improving manual phase picking. The AE/MS technique has been an intergral part of safety monitoring in mines [3] due to its capacity to identify zones of instability in a monitoring area. To obtain an accurate source of an AE/MS event however depends on the quality of the data used for P-wave phase picking [4, 5]. AE/MS data from mines are generally contaminated with excessive background noise generated by the different mining operations. The AE/MS signals of interest are mostly buried in background noise which makes it difficult to pick the P-wave phase arrivals [4]. Processing AE/MS data acquired in noisy environment remains a major challenge due to the weak nature of AE/MS signals [6]. As noted by [4] most of the data recorded in the mine environment are mainly due to events not related to AE/MS events of interest. The complexity of data in this type of environment makes the detection and picking of P-wave arrival by human experts a very difficult task."

Jan 1, 2017

Dynamic Simulation of an Alumina Refinery

Sep 13, 2010

By Henry C. Freeman

During the early period of the construction of the Illinois and Michigan Canal, about 1838, in excavating for the canal, where the present town of Utica stands, hydraulic limestone was discovered, and its value was recognized. A kiln for calcining and a mill for grinding were erected, and the cement was used in the construction of the locks of the canal. This property was subsequently bought by the present owner, Mr. James Clark, and the work has been continued to the present time in much the same primitive manner as it was begun. The bed is exposed in the Illinois River valley by stripping off a few feet of the covering rock. It is from 4 feet to 6 feet 9 inches thick, and nearly level, dipping gently to the northeast. The Utica Cement Company's establishment, which is two miles west of Utica and two miles east of La Salle, was an outgrowth of the Illinois geological survey. The writer was in charge of the district which included La Salle county, and, in working out the details of the geology of that county, discovered, below the Utica bed, another workable hydraulic limestone, which makes its appearance in the northern bluff of the Illinois River valley, rising above the water level at the point where the company's works are established. This cement group, of which there are several thin beds, lies just below the St. Peter's sandstone, with a few feet intermediate of transition-rock, which appears to represent the Calciferous, and is exhibited in place, in concretionary form, at the top of the bluff. The hydraulic beds are very regular, and the one worked by the company is 10 feet thick; or, speaking more definitely, there are two beds, separated by 18 inches of sandstone, lying about two feet above the bottom, and the two beds are worked as one, the sandstone being first cut out and removed, to prevent mixture. In 1869 I was invited to join with a company, and to take charge

Jan 1, 1885

By R. F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Bureau of Mines has developed a general method for preparing solutions from a wide range of metal and mineral samples for chemical analysis. The development of the method from current knowledge of vessel material, pressure dissolution techniques, and the fluoride-boric acid reaction is given. The method uses 7 ml of a mixture of HC1-HNO3-HF acids in a ratio of 3.5:2:1.5 sealed in plastic bottles that act as pressure vessels when heated in a boiling water bath. A final volume of 100 ml is obtained by the addition of 93 ml of a 1. 5-pct H3BO3 solution to the bottles, which are reheated; precipitated fluorides as well as sample residue are dissolved by the fluoride-boric acid reaction. A copper slag and a steelmaking slag treated using this method were analyzed by atomic absorption spectroscopy yielding values for Si, Mg, Ca, AI, Fe, Mn, Na, As, Pb, Sb, and Zn very close to certified values with an average relative standard deviation of 2.13 pct. The low cost, reduction in preparation time, ease and safety of sample handling, conservation of reagents, and ability to dissolve volatile materials without loss make this method superior to traditional wet digestion techniques for many materials, and ideal for use with atomic absorption, and optical emission or X-ray emission spectroscopy.

Jan 1, 1980

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a' range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.'

Jan 1, 1955

By T. C. Page

The Yarnell gold depoSit, located in the Weaver mining district of Yavapai County, Arizona is found within a structurally controlled, hydrothermally altered zone that occurs within a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rock that occur around and above the low-angle northeast striking Yarnell fault are known to host economic gold mineralization; a wider envelope of weakly-propylitic alterred rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz ± adularia veining, stockwork formation, and localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized), and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit although the thickness of the zone and associated alteration envelope diminish away from the orebody. A sample of undeformed illite taken from the Yarnell fault zone was K/Ar dated at 69 ± 1.6 Ma; this date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As, Cu, and Mo content. Both CO2-and H20-rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit.

Jan 1, 1992

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By Zárate G. E.

Practical and statistical considerations concerned with the sampling, sample preparation and chemical analysis of precious metal ores are reviewed. The principal requirements related with the characteristics of sample cutter, sample preparation, equipment and methods are discussed. The main errors introduced in the different stages of the sampling systems are defined. The application of statistical techniques to evaluate these errors to determine the ore grade variation and to design the number of increments needed to get an accurate assay are presented. Finally, results obtained with the application of this method to gold and silver ores are analyzed and some recommendations are given.

Jan 1, 1984

By Batterham RJ

A 'research model' can be used to investigate cause and effect relations and generally improve the understanding of extractive metallurgical processes. As such, it is a useful research technique which complements the traditional methods of laboratory and plant measurement. The procedure of model development is iterative and involves observation of the process, hypothesis of phenomena, prediction using mathematical descriptions of the phenomena and comparison of predictions with real-world measurements. Lack of agreement of predictions with real-world measurements usually indicates an inadequacy in the hypotheses and necessitates revision. Experimentation has an integral role in the process of model development but its emphasis is different from that when experimentation alone is used to study processes. Since a process as a whole is investigated by using a model, experimentation is restricted to the study of specific phenomena to aid the description of these in the model, to the characterisation of the raw materials (for initial values of the model parameters) and to the measurement of physical and chemical constants required in the model equations. Similarly, plant measurements are made for the purpose of comparison with the model predictions not to establish cause and effect relations. This makes plant experimentation much simpler and cheaper'since most measurements-can be taken during normal operation.

Jan 1, 1984

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003

By Mahony BK

This paper discusses the major infrastructure elements required to support a typical Australian mining development. Infrastructure elements are grouped into four major types, urban planning, transportation, power and communications and water supply. The design criteria applying to individual elements within these groups are briefly discussed as well as order of magnitude cost estimates. The use of simulation models to test the capacity of existing rail networks, as well as novel sources of energy generation, are also described.

Jan 1, 1983

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette' recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.'."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy's law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By R. S. Dean, John Gross

"In a preliminary report made a year ago it was shown that certain minerals when subjected to heating with water under high pressure and temperature were shattered upon the sudden release of that pressure. The main feature in which the results of this method differ from those of conventional grinding is in the differential effect obtained. The more metallic minerals, and hence the valuable minerals, are shattered more readily than are the gangue minerals. In other words, explosive shattering is unique among possible methods for comminuting an ore in that it wastes the least energy on the useless part of the ore. Explosive shattering, therefore, offers possibilities as a means for reducing grinding costs, arid it is this potential advantage of the process that makes it worthy of further experimental study. The first part of this paper is devoted to a study of the mechanism of the process; the, second part reports results obtained in toots on a selected list of ores to exhibit some of the advantages of explosive shattering."

Feb 1, 1933

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

By W. B. Plank

The figures on enrollment in the engineering schools of the United States and Canada indicate that the total number of students in these schools for the current year, 1949-50, is about 10% less than it was a year ago. This year, 226,533 undergraduates and graduate students are studying engineering in the United States and Canada as compared with 249,913 students last year. These figures are taken from advance data in the Journal of Engineering Education for February 1950.

Jan 5, 1950

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A 1/2x4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four 5/s in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of 3/s yard capacity, both manufactured by Blaw Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1950