Search Documents

By J J. Cilliers

The aim of this paper is to give an overview of the FrothSim flotation simulator and to demonstrate its ability to predict the performance of real flotation circuits. Example simulations are presented in which the feed rate to the circuit is varied, followed by simulations in which a cleaner section and recycle loop are added to the rougher bank.The simulator is able to predict both the recovery and the grade produced by the cells at all locations in a circuit and the simulator is shown to produce plausible grade recovery curves. It also demonstrated that the performance of banks of cells improve as the feed rate to the bank increased (improved grade for a given recovery), but that more cells are required to give the same overall recovery.

Jan 1, 2005

By J Evans-Wheeler

"The mandate of the 2005 VALMIN Code to provide ‘(all) reliable, thorough, understandable material information required by investors and their advisers when making investment decisions’ requires that due diligence for tenure be full and thorough. Yet a published due diligence would often appear to be simply a list of tenures allegedly held without any commitment as to the standing of the tenure as safe and secure or otherwise.The value of due diligence for tenure, as mandated in the 2012 JORC Code and the 2005 VALMIN Code, must focus on compliance rather than simply on ‘vital statistics’. Enforcement in every jurisdiction in Australia focuses on penalties (some more harsh than others) for non-compliance, which, in turn and most importantly, reflects directly on security of tenure. Some 22 Acts (on average) impinge on security of tenure and fundamentally underpin the security of any mineral asset.This paper will outline regulatory processes to demonstrate how tenure compliance is achieved and argue that the rigorous application of good practices in tenure evaluation will lead to more of this information being made available on a regular basis.The paper will then focus on further practical examples of tenure compliance failures, the application of these to the requirements of the JORC and VALMIN Codes and due diligence that failed to fulfil the mandate. Examples will be given that alerted other professionals using the JORC Code to complex geological and mining situations of which they were unaware in their valuations.Finally, the author will make a personal plea for tenure to be considered at the commencement of any reporting process.CITATION:Evans-Wheeler, J, 2016. The VALMIN code and tenure compliance – not just a list, in Proceedings Project Evaluation 2016, pp 112–121 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Charles O. Thompson

IN 1867 the city of Worcester walled in the Mill Brook for its main sewer. This stream, one of the important affluents of the Blackstone River, flows through the city in a southwesterly course from Salisbury Pond, and along its valley a considerable part of the heavy manufactories of the city are placed. At two points, a mile apart, a sufficient fall occurs to be turned to account for motive power, and at many points it was the right and practice of the riparian proprietors, prior to 1867, to use the water for steam and other manufacturing purposes. But the

Jan 1, 1881

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

By P Ormsby, T Hewitt

Ore in pillars constitutes a significant proportion of the ore reserve at PasmincoÆs Broken Hill Mine. Many of these pillars are narrow (5 -6 m) and high (16 û 35 m) vertical blocks. High-grade ore has been left between primary horizontal cut and fill stopes. These stopes were mined from the late-1960s until the early-1980s. Fill material is a variety of hydraulically stowed sand, sand-cement, and remnant timber support. Many pillar cut-throughs were made between the old stopes. In order to gain access for the current pillar recovery operations, it has been necessary to develop pillar drill drives through, and adjacent to, the hydraulic filled stopes. Whilst long hole recovery of vertical pillars is not new, some notable successes using innovative ideas have been achieved during 1997. These innovations include:The use of steel mesh reinforcing in shotcrete when mining through, or adjacent to, hydraulic fill. Construction of steel sets to support vent rises and haulage ways encountered in the cut-throughs. The use of ground movement monitoring equipment. Survey lasers with chain droppers and convergence monitors were installed in the 18 Pillar to detect any movement of the pillar block and decrease risk to personnel. The development of a three-dimensional computer model of primary stoping, using Vulcan software, to assist in the design of pillars. Maximisation of recovery using different drilling and firing practices.

Jan 1, 1998

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner(SPL) is obtained at the end of the pot's life. The SPL contains small amounts of cyanide and fluoride, which present environmental problems. Spent potliner could possibly be used as a fluidizer to replace calcium fluoride (CaF2) in the iron- and steelmaking industry and in the glass industry. A low viscosity and a low melting point are prime requirements for such an application. In the present study, viscosity measurements were performed. The effects of various additives, such as sand, limestone, dicalcium silicate dust and MgO baghouse dust, on the viscosity of SPL were studied. The results showed that the addition of sand and limestone can produce a very high fluidity SPL melt at significantly lower temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 2002

Pressing-Drill Method - A Representative Method for Taking Analysis Samples from Recycled Materials

Sep 13, 2010

By George Burgess

I. INTRODUCTION THE suggestion has often been made that it would be highly desirable, at least for certain grades of steel, to be able to control more certainly, by pyrometric measurement or otherwise, the temperatures of the operation of the open-hearth and other furnaces used in the manufacture of steel and iron. That the properties of the ingot and finally of the finished steel product are intimately related to the final temperatures attained by-the metal inn the furnace and to the temperature of casting, has been recognized by metallurgists for a long time, and this question has been very thoroughly treated, especially by Prof. Henry M. Howe, and by A. W. and H. Brearley.1 It is the object of this paper to demonstrate that in so war as casting temperatures of furnaces, steel ingots, and similar operations involving the temperatures of streams of iron and steel are concerned, well-known pyrometric methods s may be easily applied-if certain recently determined corrections are made and precautions taken-with a relatively high degree of accuracy. Greater but not insurmountable difficulties will be encountered in. the case of open-hearth furnace temperatures, while for" those of the converter type a ready solution does not seem practicable. It appears that certain essential data have always been lacking in reporting observations such as those of Le Chatelier in 1892. Thus the correction to be applied for the characteristic radiation-or emissivity¬has hitherto not been adequately taken into account nor the limitations of the several possible pyrometric methods clearly recognized.

Jan 2, 1917

By P. Rama Rao, D. H. Sastry, T. R. Anantharaman

Deformation (a) and twin (a') stacking-fault densities in cold - wor ked filings of fcc silver alloys containing 2, 4, and 6 wt pct Sb have been estimated from Debye-Scherrer peak shifts and asymmetries, respectively. Evidence has been obtained for a possible strain-induced transformation in a two-phase alloy containing 9.0 zut pct Sb. Using Fourier analysis of X-ray line profiles, the effective particle sizes and root mean square strains have been determined for the three fcc alloys in the cold-worked condition. The values of the compound fault probability 0.5a + a') evaluated from peak shifts and asymmetries are in reasonable apeement with those derived from peak broadening. COLD work of fcc metals may produce both deformation and twin (also called growth) stacking faults, which can be detected and quantitatively estimated by X-ray diffraction techniques.' In addition to peak broadening, deformation faults produce a shift in peak positions and twin faults an asymmetry of the Debye-Scherrer reflections. Besides stacking faults, a reduction in the size of coherently diffracting domains and distortion within these also broaden the powder reflections of deformed fcc metals and alloys. Fourier analysis' of peak shapes provides quantitative infor- mation about the effective domain sizes, lattice strains, and also the compound fault probability (1.5a + a'), where a and a' represent deformation-and growth-fault density, respectively. The Paterson method2 for determination of a from peak shifts, the warren3 or wagner4 method for evaluation of a' from peak asymmetries, and the Fourier analysis for quantitative estimates of all the contributory causes of peak broadening have, in the course of the last decade, been extensively applied to obtain data for a number of deformed fcc metals and alloys. One of the useful results of earlier measurements of a in several solid solutions is a correlation between a and the solute valence as well as electron concentration per atom (p) in alloy systems based on a particular solvent. The work of Smallman and westmacott5 on Cu-Zn, Cu-A1, and Cu-Sn, of Foley, Cahn, and ~aynor' on Cu-Si and Cu-Ge, and of Rama Rao and Anantharaman7 on Cu-Si and Cu-Sb has revealed a common trend in the increase of a with p and also a with valency of the solute. Cahn and Davies' and Ad-ler and wagnerg have observed similar trends for silver alloys containing cadmium, indium, and tin. Data on a for silver alloys with a pentavalent solute element are not, however, available. It is primarily to fill this need that the present investigation on Ag-Sb alloys was undertaken. Utilizing the Patersonand Warren methods, values of a and a', respectively, have been determined in three silver alloys containing 2, 4, and 6 wt pct Sb. By Fourier analysis of the broadening of Debye-Scherrer peaks, effective particle sizes, lattice strains, and the compound fault probability (1.5a +a') have also been evaluated.

Jan 1, 1967

By R. G. Agarwal, Ramey Jr. H. J., Al-Hussainy R.

Although it has long been realized that gas recovery from a water-drive gas reservoir may be poor because of high residual saturations under water drive, it appears that only limited infomlation on the subject has been available until recently. This study was performed to show the qiiantitative potential importance of water influx. Results indicate that gas recovery may be very low in some cases: perhaps as low as 45 per cent of the initial gas in place. Gas recovery under water drive appear to depend in an important was on: (I) the prodirction rate and manner of production; (2) the residual gas saturation; (3) aquifer propertie.); and (4) the volumetric displacement effciency of water invading the gas reservoir. The manner of estimating water-drive gas reservoir recovery can vary considerably. Examples are: the steady-state tnethorl. the Hurst modified steady-state method, and various unsteady-state methods such ac. those of van Ever-dingen-Hurst, Hurst, and Carter-Tracy. The Carter-Tracy water influx expression was used in this study. In certain cases, it appears that gas recovery can be increased significantly by controlling the production rate and manner of production. For this reason, the potential importance of water influx in particular gas reservoirs should he investigated early to permit adequtrtr planning lo optirtize the pay reserves. INTRODUCTION In recent years, the economic importance of natural gas production has become increasingly apparent. This has been evidenced by more intensive exploration efforts aimed at gas production, and exploitation of both deep, as well as low-permeability gas reservoirs. Technical developments such as deep-penetration fracturing have made development of such formations economically feasible. Unfortunately, water influx has forced abandonment of a number of gas reservoirs at extraordinarily high pressures. Although reservoir engineering methods for estimating water influx have long been available, it appears that application of these methods to the water-drive gas reservoir has been sporadic.'a Available methods for estimating water influx which can be applied to the water-drive gas reservoir problem include the steady-state method,1 the Hurst modified steady-state method and various unsteady-state methods such as those of van Everdingen-Hurst. Hurst, and Carter-Tracy. Interesting applications of these solu- tions to gas reservoir and the aquifer gas-storage problems have appeared recently.3,12,14 The experimental study of residual gas saturations under water drive by Geffen et al. in 1952 indicated that residual gas saturations could be extremely high. A value of 35 per cent of pore volume is often used in field practice when specific information is not available. The study of Geffen et al. showed that residual gas saturation might be much higher in some cases. Naar and Henderson concluded that the residual non-wetting phase saturation under imbibition should be about half of the initial non-wetting phase saturation. The Naar and Henderson result that residual gas saturation under water influx should be about half the original gas saturation is recommended as an estimate if laboratory measurements are not available. Thus, it is clear that a considerable portion of the initial gas in place might be trapped in a water-drive gas reservoir as residual gas at high pressure. A full water-drive would result in loss of residual gas trapped at initial reser.voir pressure. Consideration of transient aquifer behavior leads to the conclusion that high-rate production of water-drive gas reservoirs could result in improved gas recovery by reduction of the abandonment pressure. However, there appears to be little quantitative information on this possibility. One of the few advantages of water-drive gas production appears to be improved deliverability through water-drive support of the reservoir pressure. There may also be an advantage in higher condensate recovery caused by pressure maintenance for gas-condensate water-drive reservoirs. In view of the preceding, this study was made to assess the potential importance of water-drive in gas reservoir engineering. The Carter-Tracy approximate water-influx expression was used because this equation offers some advantages in hand-calculation which do not appear to have been generally recognized.' However, calculations were performed in the main with a high-speed digital computer to permit evaluation of the effect of water-drive under a large variety of conditions. CALCULATION METHOD Water-drive gas reservoir performance can be estimated in a manner completely analogous to oil reservoir calculations: a materials balance is written for the reservoir, and a water influx equation is written for the aquifer. Siniltaneous solution provides the cun~ulative water influx and the reservoir pressure. When reservoir performance data (gas produced and reservoir pressures) are available, it is usually possible to match performance data to determine the initial gas in place and the water influx parameters —

Jan 1, 1966

By W. Crafts, J. L. Lamont

Electrolytic extraction of carbides from quenched and tempered steel and their examination under the electron microscope were found to be helpful in understanding the mechanism of secondary hardening in alloy steels1 and the same technique has been applied to isothermally transformed steels. A preliminary survey of the utility of the method has indicated that it has promising possibilities for investigating the characteristics of pearlite and bainite. The examination of a few carbon and chromium steels has suggested that pearlite is formed with carbides of two varieties representing the lamellar and nonlamellar forms and that bainite appears to form with a structure analogous to, but significantly different from, martensite. Procedure The method used for examining the carbides was similar to that described previously.1 The chromium steels used in the investigation were made from an Armco iron base in an induction furnace and were not treated with grain-refining deoxidizers. The composition of the steels is given in Table 1. Three-inch square ingots were forged and rolled to 1/8-in. thick sheet for use in the isothermal studies. After rolling, the sheets were sandblasted to remove the rolling scale. Specimens approximately 3/4-in. wide and l1/2-in. long were prepared from the 1/8-in. sheet. They were heated in a salt "bath at 2100°F (1150°C) for 1/2 hour, transferred to other salt baths at 1300°F (704°C), 1000°F (538°C), 800°F (426°C), or 600°F (315°C), held for various periods up to 100 hr and finally quenched in water. After quenching, the specimens were cut in half, one half being submitted to microscopic examination and the other half being used for the electrolytic extraction. The isothermally transformed specimens were submitted to examination under the light microscope to determine the degree of transformation and type of structure and were photographed at 2000 X. Carbide residues were obtained by electrolyzing in 10 pet hydrochloric acid and collecting the residue in glycerine to minimize attack by the acid. As pointed out in the earlier paper, the carbides are attacked to some degree during electrolysis. This attack is relatively minor on the coarser carbides but may be quite severe on the fine bainitic carbides. The residues were washed free of the glycerine with water and alcohol. The alcohol was removed by repeated washings of amyl acetate, and the amyl acetate suspensions were transferred to stoppered vials. Debye-Sherrer X ray diffraction patterns of the residues were prepared using a chromium target. A selection based on the microstructure and X ray data was then made of samples considered most illustrative of the progress of transformation. Electrolytically extracted residues from these samples were submitted to examination by W. D. Forgeng and A. C. Jenkins on the electron microscope at the Research Laboratories of The Linde Air Products Co. and electron micrographs were made at X 5000 and enlarged to 25,000 X. The micrographs obtained with both the light and the electron microscopes are mounted side by side in the accompanying figures. Although no effort was made to establish the T-T-T diagram for the chromium steels, the times for holding in the salt bath were adjusted with the intention of making the samples represent different stages in the transformation at temperatures of 600, 800, 1000, and 1300°F. The degrees of transformation and results of X ray examination are shown in Tables 2—4. The carbide designations refer to orthorhombic or trigonal carbide types and are not meant to imply that the compositions are exactly as indicated. X ray Diffraction Data The occurrence of Fe3C and Cr7C3 in these steels was found to be consistent with published data on comparable chromium steels. Steels A and B with relatively low ratios of carbon to chromium contained Cr7C3 in the pearlitic structures and FeuC in the

Jan 1, 1950

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By T. Sterry Hunt

I HAVE lately had occasion to examine sulphuretted ores of bismuth both from Tudor, Ontario, and Latete, New Brunswick. The former consisted chiefly of bismuth-glance, carbonated at the outcrop, and within associated with some metallic bismuth, iron-pyrites and graphite, in a quartz gangue. In the second locality, where it appears to be present in considerable quantity, the veinstone is also quartz, but the associates of the bismuth-glance are chalcopyrite and galena. The treatment of such mixed ores in the furnace for the extraction of the bismuth could yield only a very impure product, and in view of the high price of the metal I tried with success a wet method for the treatment of the ore, which is based on well-known chemical reactions, and may, in some cases, be advantageously used. The pulverized ore is dissolved by heat in commercial nitric acid, and the remaining gangue washed by displacement, first with a little strong acid (which is used to attack a fresh portion of ore) and then with a moderate quantity of water, which is added to the first solution. This, if the excess of acid be considerable, may be partially

Jan 1, 1873

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

Mathematical considerations of green ball growth in a balling device by the mechanisms of layering new feed onto seed or recycle pellets are presented. An experimental procedure was developed for investigating the agglomerate growth by layering in which the addition of feed to a batch of seed pellets was made cyclically. Using this procedure, the layering growth mode under partial feed consumption and no seed generation conditions was investigated experimentally in a laboratory balling drum as a function of such operating variables as moisture content of the material, feed rate, and the size distribution of the seed pellets. The experimental results were analyzed in the context of the model equations and the layering growth constant was estimated as a function of the operating variables.

Jan 1, 1978

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬lows: the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circum¬stances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money- prize to the younger men, rather than the medal.

Jan 1, 1923

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By W. F. Holbrook

IN a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 pen cent MgO slags over the range 1475° to 1525° C is included The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple Twelve-gram charges of 0 8 per cent sulphur-metal and 5-gram charge-, of slag were subjected to heating for 30 nun at a prescribed temperature The charges were analyzed for sulphur content For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal Six slag and metal charges were made coincidentally in 5/8-in holes in a section of an electrode graphite rod One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO SLAGS WITH MAGNESIUM OXIDE CONSTANT 15 Per cent MgO -The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SI02, 5 to 27 per cent A1203 and 24 to 53 per cent CaO Variation in composition has been in steps of 2 per cent over much of the area Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered m steps of 4I per cent and even

Jan 1, 1938

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By M. Hekmati1

SAG/AG mills have been most common choice in grinding circuits last decades. In the most cases, at the discharge of SAG/AG mills, a trommel screen is used that is equipped with baffles to provide appropriate residence time and improve separation efficiency. Using baffles, with the resultant maintenance requirements could lead to decrease in mill availability. In this research, an innovation in the structure of baffles of a trommel is presented. The results show that using new baffles led to 67% decrease in SAG mill downtime due to problems of baffles and 80% decrease in fine particles on recycle conveyor.

Jan 1, 2012