Search Documents

By E. J. Margi

Deep gold exploration such as is used for Witwatersrand gold deposits is both expensive and time-consuming. This paper provides quantitative guidelines as to the economic optimum number of boreholes and deflections within each borehole for a certain reef characterized by its variability pattern and depth below surface in order to maximize the level of confidence for a fixed drilling budget or to minimize the total drilling cost for a given level of confidence. Portions of the Basal, Vaal, and Elsburg Reefs that show a wide range of variability (sample logarithmic variances of 0,63, 1,05, and 2,06 respectively) are examined at depths below surface ranging from 1000 m to 4000 m over a simulated mining property covering 7000 ha (7000 m by 10000 m). It is concluded that four intersections per borehole are optimum in al the cases considered, which cover the majority of current Witwatersrand exploration, with the exception of the highly variable Elsburg Reef at depths of 1000 m and 2000 m, where boreholes with one and two intersections respectively should be preferred.

Jan 1, 1987

By Frank E. Chase

Geologic structures have been responsible for numerous underground accidents and fatalities, and are a constant-source of down time. During - longwall mining, ground control problems associated with geologic anomalies are aggravated by the abutment pressures which develop as the panel is retreated. Therefore, it is imperative that these structures be recognized and properly supported in head- and tailgates. Fractures, faults, clay veins, igneous dikes, and ancient stream channels (paleochannels) disrupt the lateral continuity of the mine roof and can cause falls in gateroads. Horsebacks and kettle bottoms are also hazardous because abutment pressures tend to "pop out' these structures into the gateroads. This Bureau of Mines investigation describes the physical characteristics associated with hazardous geologic structures, identifies the coal fields where-they have been observed, and, where possible, suggests support strategies and other mine plan modifications to help minimize their effect.

Jan 1, 1990

By Marshall, L. K. Oliver

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Susan Robertson

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100% can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

Jan 1, 2002

At the Annual Meeting of the RMCMI Board of Directors held June 29, 1985, the following amendments to the corporation bylaws Article III were made: Section 2. Advisory Board. There shall be an Advisory Board of Directors which shall be com- posed of all former presidents of the corporation and of the unincorporated association, also known as The Rocky Mountain Coal Mining Institute, of which the corporation is the successor. The Advisory Board shall periodically review the philosophy and policies of the corporation and make recommendations concerning the same to the Board of Directors. The Advisory Board shall hold an annual meeting at the same place as and immediately pre- ceding the annual meeting of the members in each year and written notice stating the place, day, and hour of the meeting shall be given or mailed to each member of the Advisory Board at least thirty days prior to the date fixed for such annual meeting. The annual meeting of the Advisory Board shall be for the purpose of electing a chairman from among its members and the person so elected chairman shall also serve as a member of the Board of Directors of the corporation. The Advisory Board shall meet at such other times and conduct its affairs in such a manner as it shall determine from time to time by resolution. Section 4. Regular Meetings. A regular meeting of the Board of Directors shall be held immediately following the annual meeting of the members, at the site of the annual meeting of the members, the day and time to be fixed by the Board of Directors at its annual meeting immediately pre- ceding the annual meeting of the members in each year, without the necessity of any other or advance notice. Such regular meeting of the Board of Directors shall be for the purpose of considering committee appointments, and for the transaction of such other business as may come before the meeting. A regular meeting of the Board of Directors shall also be held in the Fall of each year following the annual meeting of the members and written notice stating the place day and hour of the meeting shall be given or mailed each member of the Board of Directors at least thirty days prior to the date fixed for such regular meeting. Such Fall regular meeting of the Board of Directors shall be for the purpose of receiving the treasurer's annual financial report of the previous fiscal year as reviewed and approved by the auditor, to take action on the budget, and for the transaction of such other business as may come before the meeting. Section 8. Standing Committees. The Board of Directors may create by resolution adopted by a majority of the entire Board of Directors, a Bylaws and Resolutions Committee, a Nominating Committee, a Finance Committee, and one or more other committees each of which shall consist of two or more directors and which shall have and may exercise such authority in the management of the corporation as shall be provided in such resolution or in these bylaws. Section 9. Ad Hoc committees. The Board of Directors from time to time may by resolution create a Membership Committee, a Scholarship Committee, an Education Committee, various convention committees, and one or more other committees each of which shall consist of members of the corporation and which shall have and may exercise such authority, other than in connection with the management of the corporation, as the Board of Directors may determine. MINUTES of the Rocky Mountain Coal Mining Institute 81 st Member Annual Business Meeting July 2, 1985 The 81st Annual Business Meeting of the mem¬bers of The Rocky Mountain Coal Mining Institute was called to order by the president, Charles W. Margolf at 1:35 p.m. Tuesday, July 2, 1985 in the Windom Peak Room of the Tamarron Resort near Durango, Colorado. Thirty members were present and a quorum was established. It was moved by Bill Balaz, seconded and car¬ried to dispense with the reading of the minutes as these were published on pages 67 thru 77 of the 1984 issue of the Proceedings. The chair called for reports of the various com¬mittees and these reports will be placed on file in the RMCMI Office. Bylaws and Resolutions. Chairman Loren V. Linville reported that the Board of Directors had adopted changes to Article III, Sections 2, 4, 8 and 9 calling for clarification of Ad Hoc and Standing Committees as well as setting forth a purpose for the Advisory Board meetings and stating a time for an annual meeting. He further reported that the Board had passed three resolutions: (One) Noting the passing of these members since the last conven¬tion - Einar M. Arentzen, Gerhardt A. Benne¬witz, Claude P. Heiner, Raymond A. Johnson, Vard H. Johnson, P. T. Schonstrom, Augusta F. Whiteside and Edward Wiemann; (Two) Of appreciation to the officers, chairmen and their commit-

Jan 1, 1985

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By Eder Villarreal, Moisés Ortega, Heo Chul-Ho, Jorge Acosta, Carlos Salazar, Cynthia Yauli, Braulio Zorrilla

Los depósitos minerales del batolito Andahuaylas-Yauri se encuentran en la franja metalogenética de pórfidos y skarn Cu-Mo-Au del Eoceno-Oligoceno. Se puede reconocer un periodo de 16 millones de años de mineralización, donde la fuente de Cu-Mo-Au de Trapiche y Constancia proviene de la corteza superior, mientras que la de Cu-Au en Utupara y Cotabambas deriva de una mezcla de la corteza superior e inferior.

Dec 31, 2018

Detailed mapping in the Permian-Triassic clastic sediments of the Southern Alps delineates a number of strike-slip faults, both dextral and sinistral, associated with the major Alpine Fault to the west and displacing a tight array of fault blocks. Concurrent steeply plunging folds are deforming early major folds of probable Cretaceous age, and generating schist locally. To the east a major collapse zone has developed along the crest of a Cretaceous anticline, located over an ancient Permian submarine scarp, with a number of small normal faults. Further east, extensive Carboniferous to Triassic rocks of much the same appearance are exposed as horsts and grabens in a large possible extension zone through central and east Canterbury. This may have crept incrementally from Cretaceous from the offshore Bounty Trough to reach the eastern margins of the Southern Alps in the Pleistocene.

Jan 1, 1990

By John M. Pitt

A rapid in situ stress measurement technique was developed for exposed underground surfaces. The method applies radial stress in small diameter (38mm) boreholes, initiating fracture propagation which is monitored by measuring ultrasonic pulse velocity. Theoretical relations for stress concentrations near boreholes provide independent expressions for unknown principal field stresses at incipient fracture; fracture orientation defines principal stress orientation. Accuracy and precision were evaluated using blocks of brittle material subjected to known stresses. Results were comparable to those obtained by other in situ stress measurement techniques.

Jan 1, 1984

The resignation of Herbert Hoover, Director General of Relief in Europe, from his post as Chairman of the Board of Directors of the Food Administration Grain Corporation, in which capacity he had served for nearly two years; and the reorganization of the corporation under the name of the United States Grain Corporation, with Julius Barnes, United States Wheat Director, as its new head, took place at the annual meeting of the stockholders, held in New York, July 1. This action on the hart of Mr. Hoover is believed to be one of the first steps in his intended withdrawal from public service upon the conclusion of the war service of the various departments of the Food Administration, or as soon as they shall have been absorbed by other agencies. The Grain Corporation has been, for the past two years, a vast collection and distribution agency. Its function has been to assist in supplying to the Allies and the American Army and Navy large quantities of wheat, wheat flout, and other foods, with very little disturbance of American prices, and with such an even control of American distribution that reserves from one crop to another have been brought down to the lowest possible compass and without the dvelopment of actual scarcity anywhere in the United States. In the year just past, it carried on all the buying and the shipping for, the Belgian Relief Commission, until the commission retired on May 1 and the Belgian Government itself undertook its own overseas supplies. During the twenty-two months of its existence the corporation had disbursed $3,500,000,000 and collected an equal amount, selling for over-seas shipments commodities valued at $1,800,000,000, at an operating expense of about $3,250,000, or one-sixth of 1 per cent. During this time it has not lost a single dollar through fire loss.

Jan 8, 1919

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010

On Jan. 1, the office of the. National Service Committee was established at 502 McLachlen Building, Washington, D. C. The first work was to review current legislative information; which is being continued and good results are accomplished. Whenever matters of importance appear in the Congressional Record, notice thereof with such documents as are germane are forwarded to the members of the committee for their information and advice. The first formal report of the chairman was on the so-called Smith-Howard bill to secure Federal endowment for the establishment of engineering research. The chairman of the Committee, at the request of the Executive Committee of the Engineering Council, appeared before the Senate Committee on Education and Labor for the purpose of opposing those features of the so-called Kenyon bill which would create a practically permanent commission dominated by the Engineering Corps of the Army over all Federal engineering projects as well as state and municipal projects receiving Federal aid. The greater part of the time has been expended in correspondence and consultation on the matter of the establishment of a Department of Public Works. The results of this work lead to the belief that there is much promise of the establishing of such a department by the 66th Congress Hall members of engineering societies, as well as the societies themselves, will unanimously agree on and support a measure, and in order to secure such unanimous support, it will be advisable to call a conference of engineering societies. .

Jan 4, 1919

By K. K. Kershner

The purpose of this research by the Federal Bureau of Mines was to investigate the recovery of tin from mine-run ores and low-grade concentrates. Over 95 percent of the total tin in such materials was volatilized to tin chlorides at temperatures ranging from 520° to 565° C. Gaseous mixtures of hydrogen and hydrogen chloride were used for reducing cassiterite to stannous oxide and for converting this compound to tin chlorides. The chlorides were swept from the reaction zone of an oscillating kiln by a rapid flow of reactant gases and collected in a condensing system. Losses of tin that occur in current metallurgical processing were prevented. Approximately the same time of treatment was required for minus 35-mesh mine-run ores and low-grade concentrates. In a continuous process, the circulating gases would require some enrichment.

Jan 1, 1961

Mr. Murray said: Having recently returned from a visit to America, it may be of interest to members to hear something from me of the mining fields and metallurgical works which I had the opportunity of seeing, and the impressions which I formed concerning general practice and conditions there, as compared with our Australian standards in the mining industry, and in matters generally.The most striking feature of the North American continent is thehuge plan upon which Nature has built, the multiplicity of immense mountains, rivers, and lakes, the snow-covered tops of the former forming reservoirs for the latter during the summer months, being most impressive to the Australian visitor. Starting from Vancouver I travelled east for over 500 miles through the wonderful Canadian...

Jan 1, 1927

By A. A. Beland, R. J. Dawson, S. Shewchuk

"Shovel buckets, scraper blades, dipper teeth, mine car wheels and hammermills are examples of equipment which require routine maintenance due to abrasion. Service life can be extended by the use 0/hard/acing and buildup materials. Mining and milling applications are described and field welding procedures discussed.A high-stress abrasion test used to select hard/acing and buildup materials/or hammers in a hammermill is described in detail. Field tests of the selected alloys confirmed their performance, and maintenance records showed a significant saving in down time and cost.The relationship between the abrasion resistance of the alloys and their hardness, work hardening, composition and microstructure is summarized. IntroductionLarge volumes of ore are handled daily by the mining industry. The abrasive nature of most ores results in extensive wear to both handling and processing equipment. If such wear is neglected it may cause lost production time and also, in extreme cases, require the complete replacement of expensive equipment. The well-planned maintenance of components subject to abrasive wear by means of buildup materials and hard facing can result in substantial economic benefits. Such benefits can , however, only be realized through the correct choice of welding process, consumables and deposition methods available to maintenance personnel. Hardfacing MethodsHardfacing is applied by a variety of methods; the three most widely used being arc welding, oxyfuel gas and thermal spraying. Table 1 summarizes the major processes used within each method. Filler metals in the form of rod, wire or powder are necessary to fulfill the individual requirements of each process. The filler rods are available in the cast form or, in the case of ductile metals or alloys, as wrought rod or tube. All types are supplied bare or flux covered. Wire is supplied in two forms, drawn flux cored and drawn solid. Powder filler metals are available in many metals or alloys; they may be simple mechanical mixtures or prefused and atomized alloys made to a specific size range and shape for optimum results for each applicable process."

Jan 1, 1980

By Desmond M. Connor

"The State of the EnvironmentRecent data from a State of the Environment report prepared in January 1991 and released in April (see references) , indicates that the physical and biological environment across Canada is deteriorating in some important ways. For example: • emissions and atmospheric levels of CO2 are rising at a rate more than 50% of the U.S. increase; global temperature continues to rise, especially during the last decade;• while S02 emissions have been falling since 1984, NOz has declined only slightly since that time; N02 in Canada rose 43% during 1970-87, compared with a 7% rise in the U.S.;• municipal discharges of phosphorus and BOD (biochemical oxygen demand) to fresh water have been rising steadily since 1983);• pulp and paper mill discharges to fresh and Pacific coastal waters have been rising, 1970-87;• migratory game bird populations (Prairie Mallard, Northern Pintail) have been declining for the last 20 years;• total per capita energy use continues to climb.The State of the PublicSimilarly, data from recent public opinion surveys shows that public concerns about the environment are either rising, or are remaining at a high level despite the competing claims of the economy and political events for attention.For example, Professor Reginald Bibby's national survey this year shows that Canadians rank our top three issues as theeconomy, the environment and government incompetence.An Angus Reid survey commissioned by the Mining Association of Canada and other mining organizations in 1989 showsthat, despite general support for its economic benefits:• 67% of the general public perceive the mining industry to be a major source of pollution and environmental contamination;• 68% believe that a new mine should not be developed if it will disturb local wildlife;• 52% would prohibit a new mine if it required a road through a national park;• 49% would disallow mine development if it took as much land as an average farm in an agricultural area or if it limited sports fishing in a local lake."

Jan 1, 1991

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the Bureau of Mines studied the 350-acre Henry?s Lake Wilderness Study Area (ID-035-077) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in northern Fremont County, ID, approximately 140 air miles north-northeast of Pocatello and 3 miles south of the Montana border. The Wilderness Study Area is near the north shore of Henry's Lake at the foot of the southwest-facing slope of Black Mountain. Archean hornblende gneiss, the main rock type present, crops out northeast of the Madison Range Fault, which trends northwest across the southwest corner of the Wilderness Study Area.

Jan 1, 1988

By A Self, B Robertson

During 2015 and 2016, the authors conducted a number of surveys, workshops and reviews of ventilation and gas management practices in Australian underground coalmines. The study was funded by ACARP with a brief to identify gaps in ventilation and gas management practices for current and future needs, and to prepare a road map for change that would assist in delivering improvements.The study found that despite many examples of leading practice, gas and ventilation management is not afforded the attention and priority that is warranted and that this must be remedied if future operational performance targets are to be achieved and the safety of the industry protected. This paper summarises the findings of the study and presents the recommendations proposed.CITATION:Robertson, B and Self, A, 2017. A review of ventilation and gas management in underground mines, in Proceedings Australian Mine Vent Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

By James K. Grunig

As the real price of uranium increases, deposits of lower and lower grade will be treated. The various occurrences of uranium ore are described and the chemical aspects of extraction are detailed.

Jan 1, 1981