Search Documents

By Anibal Gajardo

Clays for building bricks and roofing tiles in Chile are classified as common clays and ball clays, with deposits of sedimentary and residual origin, both Cenozoic in age. Deposits are known from north to south, through 11 of the 13 Chilean Administrative Regions, 18° to 39° South latitude, and from west to east, through three of Chile's main geomorphic features, namely the Coastal Plains, Coastal Range, and Intermediate Depression. Alluvial and lacustrine sedimentary common clay deposits are located in the northern and southern Intermediate Depression. The average chemical composition of clay deposits in I and I1 Regions, is 58 percent Si02, 16 percent A1203, and 4 percent Fe203 by weight; the primary minerals are sericite, quartz, feldspar, and albite. The average chemical composition of clays in Metropolitan, VI, and VIII Regions, is 52 percent Si02, 16 percent A1203, and 6 percent Fe203 by weight; the primary minerals are montmorillonite, quartz, and plagioclase. Residual common clay deposits occur in the Intermediate Depression and in the Coastal Range internal basins, VII, VLII, and IX Regions, and they represent surficial alteration of pumice beds and crystalline rocks. The average chemical composition of clay deposits derived from crystalline rocks is 58 percent SO2, 17 percent A1203, and 9 percent Fe203 by weight; the primary minerals are sericite, quartz, and clinochlore. Clay deposits formed from pumice beds contain 47 percent Si02, 24 percent A1203, and 10 percent Fe203 by weight; the primary minerals are kaolinite, feldspar, and cristobalite. Sedimentary ball clay deposits are located in the Coastal Plains and Coastal Range, VI, VII, VIII, and IX Regions, between 34" and 39" South latitude. The average chemical composition of the ball clay deposits is 51 percent ,902, 28 percent A1203, 5 percent Fe203 by weight; the primary minerals are kaolinite, quartz, and sericite (illite?). These clay deposits supply the Chilean building sector with over one million metric tons (mt) (1.1 million short tons [st]) of material per year. The average growth rate of clay consumption during the period 1993 through 1997 was 10 percent annually. The clays are used by both mechanized plants and handcraft facilities.

Jan 1, 2001

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous 'merry-go-round' operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979

The Virginia Center for Coal and Energy Research has been developing models of wireless signal propagation in underground coal mines since 2007. The current mine propagation modeling software, named COMMS, is able to locate potential broadcast points for underground wireless mesh systems and estimate their coverage. COMMS utilizes programmed routines to calculate necessary values to both quantitatively and qualitatively solve and analyze predicted coverage areas. The program approximates the spatial relationships that are encountered, such as ventilation regulators, belts and other obstructions. Using this model for propagation allows the optimal communications node locations to be calculated, by using lessons learned from current installations and experience with the new technology. In addition, the optimization can be calculated by checking all possible combinations of broadcast locations. This paper compares these optimization calculation methods. The ability to solve a mine?s communication network provides a pre-installation mine network design map, creates coverage maps of the mine and allows planning for future communication activities

Jan 1, 2011

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By Frederick Laist

THE ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaces, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of -copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper;: this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it was found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first-.and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator, produces a product that is self-fluxing; in fact, it is possible to produce a

Jan 1, 1920

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By C. R. Ince

The term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalco-pyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggartl has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 Ib. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 Ib. per ton were added to the thickened pulp and the whole

Jan 1, 1930

By T Smith

The evaluation of a new mineral resource and its economic viability is critically dependant on the quality of the assay data as it is this data that defines the grade of the resource. However, all too often the procedures of sampling and chemical analyses used to generate such data are neglected or given little consideration until final modelling and evaluation are under way. This approach frequently requires large reassay and/or re-sampling programs to be undertaken to validate or to improve the integrity of the data base. This paper outlines a step by step approach to ensure quality data is achieved and then maintained throughout the entire exploration and resource development program. This involves the use of correct field sampling methods, assay methods designed to give the required levels of accuracy and precision and quality procedures in place to monitor the effectiveness of the overall process. Thorough documentation is an overriding and necessary part of the entire process. Practical examples are given to demonstrate the use and value of these methods.

Jan 1, 1998

By Rob Farnfield, Mike Kelly, Toby White

There are a variety of sources of dynamic stress which can affect a building and give rise to cracking. A two-storey house, situated in the middle of a surface coal mine was monitored for a period of 30 months to attempt to identify the major causes of cracking. The factors described as environmental include internal and external temperature, humidity, wind speed and direction, rainfall and water table level. These were monitored using a weather station and piezometer and recorded every 20 minutes. The other factors are vibratory and include normal household movement (walking, shutting doors etc.), vehicle vibration and blast vibration. All the significant vibrations in the house were recorded using four sets of velocity transducers and accelerometers.

Jan 1, 1993

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Werner Engelmaier

Constant-strain rotating-bending fatigue tests were conducted on 2024-T3 aluminum alloy constant-strain McAdams-type specimens in ultrahigh vacuum, 10-lo Torr, and in atmospheric air. In the elastic strain range the ratio of vacuum-to-air fatigue life varied from about 10 at a maximum bending stress of 37 ksi to near unity at the endurance limit. After 10 pct of the fatigue life, intergvanular microcracks appeared on the surface which did not appreciably propagate further until the last 5 pct of the fatigue life, where trans-granular cracks propagating first in slip-plane cracking and then in the stress-dominated mode led to failure. No reduction in residual tensile strength resulted from the fatigue of the specimens short of fracture. The mechanism governing the fatigue life operates between the occurrence of the intergranular microcracks and the initiation of the trans granular cracks. MORE than forty years ago, Mc Adam' and Haigh2 published the first systematic studies showing that the fatigue properties of metals were greatly affected by environments. Gough and sopwith3 found in a later study that the fatigue life of metals subject to corrosion can be substantially increased by reducing the atmospheric pressure. This and their later work4'5 was, however, done in a vacuum of only 10~3 Torr. Subsequent studies6-' at a vacuum of 10- Torr showed that water vapor is the primary agent affecting the fatigue properties of aluminum alloys. Only recently was ultrahigh vacuum used for fatigue studied.l Various theories have been put forward to explain this phenomenon. Wadsworth and Hutchings12 postulated that cracks form very early in the test and that the chemical attack by the corrosive components of the atmosphere at the root of the cracks enhances the speed of the crack propagation. They also noted that chemisorbed layers of gas on the fresh crack surfaces prevent cold welding of the crack and make the separation irreversible. Ham and Reichenbach, on the other hand, reported that their specimens showed no cracks after a run in vacuum, even though the runs were long enough to have caused the specimen to fracture in atmospheric air. They also reported that in argon at 0.14 Torr the fatigue life was about 5 times longer than at 7 X lo-' Torr. Jacisinll reported that fatigue tests in dry nitrogen showed results close to those obtained in ultrahigh vacuum. The present experiment was designed to determine the extent to which cumulative fatigue damage, i.e., the accumulation of length of fatigue cracks, reduces the residual static tensile strength of an aluminum alloy in both ultrahigh vacuum and atmospheric air and to obtain fatigue-life data for this aluminum alloy at various strains. It was also hoped that information ex- tracted from these data might support one of the previously mentioned theories. 1) EXPERIMENT Test Specimens. The material tested was commer-cial 2024-T3 aluminum alloy. In addition to aluminum, this alloy contains approximately 4.4 pct Cu, 0.5 pct Fe, 0.5 pct Si, 0.6 pct Mn, 1.5 pct Mg, plus smaller amounts of other elements.13 Some typical mechanical properties of this aluminum alloy are listed in Table I.'~ The material was used in the as-received condition, i.e., solution-treated and cold-worked. Mc Adam-type1' constant-stress specimens and notched fatigue specimens were machined from 4 -in. -diam rods, Fig. 1. The critical section of the McAdam-type samples was polished with a 45-deg spiral motion to a No. 8 microfinish. The notch in the notched specimens was machined on a lathe with a forming

Jan 1, 1969

By W. C. Peters

From the time of its beginning in the mid-19th century, the American barite industry has had its major development in the eastern and central states. Geologic and economic factors serve to maintain Arkansas, Missouri, and the Southern Appalachian states in the lead position. In earlier days, the major markets for barite were in paint, chemical, and glass manufacturing, and the favored deposits were those which were close to eastern industrial areas; furthermore, the eastern deposits were cheaply mined and required little or no beneficiation. In the last few decades, the use of barite as a weighting medium for muds in rotary oil well drilling has caused a great expansion in the industry, but the marketing picture is still centered outside of the western states-now on the Gulf Coast area where high pressures are common in oil wells. Low cost imported barite, readily available on the East Coast and Gulf Coast, has always been a major marketing factor in the industry. The major barite producing state is Arkansas, with the industry centering about the Magnet Cove area. Missouri ranks second, with production mainly from residual deposits. Several Southestern states are actively producing from residual deposits.

Jan 9, 1958

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By A. W. Deurbrouck

This report presents the results of a washability study of 322 coal mine samples showing the sulfur forms and distribution in the coals. The samples were collected from mines which were principally utility coal producers. Generally, the data show the total sulfur content of the coals evaluated could be significantly reduced by some combination of stage crushing and specific gravity separation. However, few coals could be upgraded to a final product containing 1 percent or less total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds.

Jan 1, 1972

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By J. Engel

The talc deposit in Gemerská Poloma lies 350 to 400 m under the surface; the whole deposit is located at the highest-level drinking-water-source protection zone, therefore, opening in this mining area (a well, a ramp) requires higher investment, operational and water protection costs. The adit, outside the mining area, with a length of 4200 m, rising with a gradient of 3? and a diameter of 10.3 m2, allows free passage/runoff of mining-water through the adit, and guarantees low costs for transporting produced material and equipment. This solution is in total less demanding from both investment and operational point of view.

Jan 1, 2007

By J. A. Russell

IT IS the purpose of this paper to show how the design of the larger slope hoists in use in the mines of the Dominion Steel and Coal Corporation has tended to evolve ta suit the particular conditions of operation. These hoists are all used for hauling coal in trains or trips of pit tubs up the mine slopes, which usually follow the dip of the seam . As the mine is developed to the dip and the slope grows in length, the length of the rope and the size of the hoist required to handle it rends to become extremely cumbersome. It has been found that the best economic conditions of hoisting are obtained when the length of the slope is limited to about seven or eight thousand feet. Beyond this length it is necessary to offset to one side of the line of slope and start a second or auxiliary slope, which will be served by its own hoist installed underground. With this hoisting distance as a basis, we find that we can economically hoist the outputs required, usually about 1,500 tans per eight hours per slope, by hoisting the coal in trips of about twenty boxes. This, on the grades obtaining, will require a rope of about l 1/4in. diameter, running at a speed of 1,200 ta 1,800 feet per minute, and requiring from 1,200 to 1,800 h.p. at the hoist shaft. The tendency is for the rope speeds of the surface hoists to be a little higher than the underground hoists which relay to them, so that the surface hoist has a small margin of time in hand. The oldest surface hoists were steam-driven, but, with few exceptions, these have given place to electric hoists. With the exception of one hoist, which was altered in design, the steam hoists have not had the opportunity of evolving in the same way as the electric hoists, and will not be mentioned any further.

Jan 1, 1944

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987