Search Documents

By Albert S. Trube

The purpose of this paper is to clarify the definition of compressibility and to present a uniform basis upon which instantaneous compressibilities of liquids and gases can be compared. The equations gaverning the instantaneous compressibilities of imperfect gases are derived and the concept of pseudo-reduced compressibility is introduced. Part of the data presented by Brown, Katz et a1 on compressibility factors for natural gases has been rearranged. A graph of pseudo-reduced compressibility vs pseudo-reduced pressure for various pseudo-reduced temperatures is presented. The need for additional work in relating the compressibilities of liquids and gases is discussed. This information should be of value to reservoir engineers in making non-steady state performance calculations in gas reservoirs. It should be of further use irz pointing the direction for additional research in the nature of liquid and gas compressibilities. INTRODUCTION With the increasing use of steady and non-steady state well and reservoir data, there is a corresponding increase in the importance of the various factors entering into such calculations. Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of the reservoir fluids well in advance of the more accurate laboratory data. One such factor is the isothermal coefficient of expansion of the media which are transmitting and attenuating the non-steady state pressure waves. The average isothermal coefficient of expansion, or "compressibility" is a complex function controlled by the physical properties of the formation and the fluids contained therein. The isothermal expansion coefficients for reservoir gases are usually quite variable, in many cases being highly-pressure sensitive. The coefficients for reservoir liquids tend to be pressure sensitive, but not nearly so much as reservoir gases. The coefficients for solids, usually expressed in terms of a "modulus of elasticity" are relatively insensitive to pressure variations within their elastic limits. For this reason, and also because many previous applications have been limited to rel- atively small pressure ranges, there has been a tendency to ignore the variable nature of isothermal expansion coefficients and treat them as constants. Also, the term "compressibility" by which these coefficients are generally designated is commonly confused with a similar term, z, used to define the deviation of an imperfect natural gas from the perfect gas laws. A clear distinction should be made at the outset between the term "compressibility", which is an isothermal coefficient of expansion of a substance, and the term "compressibility factor", z, which refers to the deviation of a gas from the perfect gas laws. Although the scope of this paper is limited to the compressibility of single phase natural gases, it is definitely related to the problem of accurately estimating the compressibilities of single phase hydrocarbon reservoir liquids, which will form the basis of a future presentation. BASIC PRINCIPLES The coefficient of isothermal compressibility of a substance, c, is usually determined from pressure-volume or pressure-length -measurements depending upon whether the substance is single phase gas, liquid, or solid. A convenient method for making such estimates for a finite change in pressure and volume at constant temperature is to use the well known equation V1-V2/V1 (p2 - p1) .....(1) Eq. 1 is negative because the volume of a confined substance decreases as the pressure is increased. In this case V1 > V2 and p2 > p1. This equation is useful in approximating the compressibilities of single phase gases and liquids undergoing small pressure changes. It is evident, however, that this equation is almost identical with the determination of Young's modulus of elasticity for solids. If the assumption is made that change in length is directly proportional to change in volume, as would very nearly be the case for a steel rod in tension within its elastic limit, then E5=-L1 (p2 - p1)/L1 - L2 .......(2) in which E. is the isothermal expansion coefficient, or Young's modulus of elasticity, for a solid. And further, for this special case L1 (p2 - p1)/L1 - L2 .......(3)

Jan 1, 1958

By B. Suresh

Iron ore in Bellary-Hospet region is friable in nature and generates a significant amount of micro-fines (-150 µm) during mechanized mining, handling and processing. Present beneficiation practice generally employs spiral classification followed by hydrocycloning to remove slimes (-15 µm). The iron ore fines, beneficiated at JSW Steel Ltd., Karnataka generates tailing having 48-52% iron content in the form of slimes, which accounts for 50 to 55% by weight with respect to classifier overflow. The loss of iron as slime is considerably high. In this context, laboratory studies were carried out with different combination of beneficiation techniques with an objective to develop an efficient flow sheet to achieve better product grade and recovery from classifier overflow. The results revealed that de-sliming process by hydrocycloning in combination with either magnetic separation or froth flotation leads to increased iron loss in tailing. Based on investigation it is observed that forward flotation is beneficial over the reverse flotation. The experimental approach of forward flotation on classifier overflow followed by magnetic separation on flotation tailing resulted in overall product grade of 62.9% Fetotal and 70.3% yield. The tailing contains 34.6% iron, which accounts for 29.7% by weight with respect to classifier overflow.

Sep 1, 2012

By Dae S. Young

The Disjunctive Kriging (DK) procedure was developed to estimate ore recovery figures within a deposit/ domain from limited diamond drill hole (DDH) core assay data taken at the exploration stage. Local recovery figures include minable ore tonnage and ore grades within relatively small areas such as stopes or small panels on a pit bench, for a given cut-off grade. The grade and tonnage should be computed based on the true selective mining units, that is, the average grade distribution of selective mining units within a panel. Local recovery figures are critical information for economic and engineering feasibility studies before mine development, as well as for short-term mine planning for operating mines. This kind of information can be provided only by non-linear geostatistical methods including DK and the Multivariate Gaussian Approach (MG) (Journel, 2, Parker, et al, 5).

Jan 1, 1982

By W Baguley

Attritioning has been a method of improving mineral extraction for over 60 years, however it is only recently that an understanding of the mechanism employed and the improvement in efficiency that have been achieved.The paper will discuss these improvements and how to overcome the problems that have been raised. At present there is a dearth of information on the correct design and operation of these machines.The paper will address these issues as well as fluid on the Zeta potential, micro shear, retention residence time and pilot plant operation.A study on the hydrodynamics of attritioner operation has been identified and will be discussed.Surface chemistry, clean lines of attrition material and the treatment of fines significant advances in the understanding of attritioning highlighted.CITATION:Baguley, W, 2013. Attrition scrubbers, in Proceedings MetPlant 2013 , pp 229-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By K. Walanabe

Kosaka Smelter & Refinery has a history of more than a century as a metallurgical department belonging to Kosaka mine. It has treated for a long time the "Black Ore" or the complicated concentrates dressed from it. The "Black Ore" is composed of black sulfides. It contains not only valuable metals such as gold, silver, copper, lead and zinc but also some impurities like arsenic, antimony and bismuth. With the development of Kosaka's floatation technology, five kinds of concentrates (copper, zinc, lead, pyrite and barite) have been separated from the "Black Ore" but the separation was not complete and each concentrate contained some unfavorable impurities. In 1980s the highly appreciated yen and the drop of the metals prices forced many domestic mines to close their operations. Since then Kosaka Smelter has changed its way of operation to a custom smelter. Now more than 95% of copper concentrates are imported to take advantage of this technology of "Black Ore" treatment. It mainly treats the raw materials that contain high gold and silver like the "Black Ore". Recently, Kosaka has been working on the recycling of the metals from the printed circuit board scraps and sludge which contain some precious metals. The volume of the recycled metal is continuously increasing.

Jan 1, 2003

By W. Mitchell, B. H. Bergstorm, C. L. Sollenberger

A unique compression testing machine was constructed to load individual 1/8 to I-in. spheres of glass, etc., at rates from 100 to 100,000 lb per min. During loading the applied load was continuously plotted us the deformation of the sphere-platen system. The load-deformation curve conforms to the theory of elasticity. The spheres were surrounded by steel retaining rings or by gelatin (to prevent secondary fracture). The product size modulus was determined from screen analyses. The data shows: 1) Energy input per unit mass is inversely proportional to the product size modulus (or directly proportional to the surface area per unit mass). 2) Increased loading rates slightly increase the energy input per unit mass required for fracture without affecting the preceding relationship. Theory and experiments show that much of the input strain energy is transformed into kinetic energy of fragments at fracture, this being a reason efficiencies based on "surface energies" are exceedingly small. This large kinetic energy component is usually dissipated as heat but may be partially reclaimed because impact of fragments against the surface of steel retaining rings causes additional comminution. There are currently several theories of crushing, all of which can be derived from the general energy equation of Gillilandl as was pointed out by Mitchellet al in 1954'and more recently by Rose and Sullivan. If the exponent of the equation dE-x-"dx is assigned values of 2,1, or 3/2, one obtains by intergration between suitable limits, the equations of Rittinger, kick,' and Bond,' respectively. Other investigators prefer to let the exponent be a variable parameter. To help resolve the controversy, the Allis-Chal-mers Research Laboratories set up a series of carefully controlled experiments in which the level of energy input required to induce the comminution of a single particle by slow compression loading was very accurately measured. The energy input requirement, in conjunction with the size analysis of the fragments produced at fracture, yielded an accurate energy-product size relationship for the conditions studied. APPARATUS The experimental apparatus was designed to apply a compressive load on opposite sides of an "ideal particle." Spherical shapes were chosen, because point contact loading is typical of the mechanics of conventional crushers. The bulk of the experimental data was obtained with glass spheres because glass is a fairly homogeneous, brittle material for which the properties follow definite statistical distributions. The spheres ranged from 1/8 to 1-in. diam. The compressive load was applied to the specimen at a uniform rate by a loading mechanism (Fig. 1) which acted through a system of levers. The uniform rates, ranging from 100 to 100,000 lb per min, were obtained by metering water into a bucket suspended at the end of the secondary level. Point contact was made with the sphere through tungsten-carbide platens. This latter material is extremely hard and has a high modulus of elasticity, thereby having a minimum of distortion when loaded. The actual load on the sphere was measured independently of the lever system by a load cell, Fig. 2, which was designed so that the voltage output of the load cell would be proportional to load. The deformation of the specimen was indirectly measured by a pair of transformers which were attached to opposite edges of the upper platen. The cores of the transformers, which were attached to the lower platen, moved relative to the transformer so that the voltage output was proportional to the deformation of the sphere-platen system. The load was plotted against the deformation on an X-Y recorder. The area under the curve, as shown on Fig. 3, was proportional to the energy input of the

Jan 1, 1961

By César García

La optimización de los costos de una empresa minera va de la mano con la Seguridad, Medio Ambiente y producción. En ese sentido, el presente texto señala el uso de las tecnologías de información en la mina Pierina para sistematizar los datos geológicos y tecnológicos. De forma que la información implementada - tanto manual y electrónicamente- señale el progreso de la mina. Así también se comparte la información con las diversas áreas para un posterior análisis y toma de decisiones futura

Jul 17, 2000

By George P. Demopoulos, Yan Zeng, Zhibao Li

Precipitated silica is marketed with a rising demand as reinforcing filler in the rubber industry and as a potential raw material for the synthesis of lithium-ion battery electrodes. Due to an awareness of the environmental impact of the existing processes for the production of precipitated silica, a green and sustainable process was proposed by using sodium bicarbonate (NaHCO3) as an alternative to sulfuric or hydrochloric acid in the precipitation reaction with sodium silicates. The use of NaHCO3 allows for better control of the supersaturation and pH to form silica with desired quality. Additionally, Na2CO3 solution as the process by-product is recyclable because it could be recovered to produce NaHCO3 by absorbing CO2. The solubility of sodium metasilicate nonahydrate (Na2SiO3·9H2O) in the Na-CO3-HCO3-OH-H2O system was measured using a dynamic method in the temperature range from 288.15 to 308.15 K. It is found that the solubility of Na2SiO3·9H2O decreases with increasing concentration of either Na2CO3 or NaOH over the investigated concentration range. With the aid of the OLI platform, a chemical model for the Na2SiO3-Na-CO3-HCO3-OH system was established with newly obtained interaction parameters of the Bromley-Zemaitis model by regression of experimental solubility data. The new model predicted the solubility of Na2SiO3·9H2O in multi-component systems with good agreement and was used to conduct a preliminary feasibility study of the new process.

Jan 1, 2015

By Herbert H. Kellogg

The chemistry of sulfide roasting is analyzed to show those aspects of performance which Thecan be predicted from considerations of thermodynamic equilibrium. It is concluded that equilibrium calculations can serve as a yardstick for prediction of roaster-gas composition and sulfate formation in the calcine for fluid-bed roasting practice. A method of calculation which combines the equilibrium and stoichiometric factors is outlined, and illustrated by an example from the roasting of Cu-Fe sulfides. ON first examination the roasting of sulfides would not seem to be a process to which equilibrium calculations could be applied to yield results of practical value. The burning of sulfides is an ex-tremely spontaneous reaction, excess air is always used to obtain rapid reaction, and in most traditional roaster designs (hearth roasting) the temperature and gas composition vary widely from point to point in the roaster. These are all conditions which promote a non-equilibrium state in the roasting process. However, the introduction of the fluid-bed roaster1 has brought to roasting practice new conditions of operation, so that equilibrium calculations can be used to predict certain limited aspects of practical operation. The fluid bed is characterized by uniformity of temperature, gas composition, and calcine composition from point to point throughout the bed. These relatively uniform properties of the bed make the meaningful calculation of the equilibrium state of certain reactions in roasting possible. It is the purpose of this paper to analyze roasting from an equilibrium viewpoint, to show where the method may be expected to yield valuable information, where it fails, and to outline methods of calculation. Main Roasting Reaction The reaction MS (s) + 3/2 0, = MO (s) + SO, [I] might well be called the main roasting reaction. It adequately accounts for the well known facts that metal sulfide and air are the main reactants, and metal oxide and SO, the main products. Deviations from this simple stoichiometry will be discussed under side reactions. For all metal sulfides, Reaction 1 is strongly exothermic and the equilibrium position is far to the right. Since the reaction is exothermic, the equilibrium shifts in the right-to-left direction as the temperature is raised. However, at all practical roaster temperatures (between 500" and 1200°C), the amount of this shift is small, and the equilibrium position remains far to the right. The main roasting reaction is essentially irreversible, and the application of equilibrium considerations to this reaction will not be! a fruitful field of investigation. A knowledge of the rate of this reaction. although not the proper subject of this paper, is of great importance to the roasting process. Analysis of the factors which influence this rate shows that: 1) The rate will increase rapidly with increased temperature. 2) The rate will be proportional to the partial pressure of oxygen at the surface of the reacting particle. Because of diffusion effects, the partial pressure of oxygen at the particle surface may be considerably less than in the bulk of the roaster gas. For this reason, intimate contact between gas and solid and high relative velocity between gas and solid, such as can be obtained in a fluid bed or flash roaster, will markedly increase the rate of reaction. 3) The rate will be proportional to the surface area of metal sulfide. Therefore, smaller particle size will permit a more rapid rate per unit of weight. To achieve practical rates of roasting the partial pressure of oxygen in the roaster gases must be maintained at a finite level at all times. Even where the gas-solid contact is very good, as in the fluid-bed roaster, the oxygen content of the gas must not be allowed to drop below some limiting value (perhaps 1 pct), or the rate of the main roasting reaction will become too small for practical operation. Side Reactions in the Gas Phase The gas phase during roasting of metallic sulfides contains the elements oxygen, sulfur, nitrogen, by-

Jan 1, 1957

Gold was discovered in the Bendigo area of Victoria in 1851 (Willman and Wilkinson, 1993), and all the early gold mining of any note involved washing (puddling) the gold out of the regolith or alluvium. The waste material from this process was a semi-fluid mixture of rock debris, soil and water, referred to as `sludge'. Puddling machines were gradually introduced to speed up the puddling process (Cole, 1994), and by 1855 an estimated 2000 machines were in the district (Anderson, 1978). In 1859 it was estimated that approximately 2 293 000 m3 of material was puddled annually by the machines on the eastern side of the goldfield, whose waste drained into Bendigo Creek and its tributary gullies. It was also estimated that after the gold was removed, approximately one-quarter of the residue/sludge consisted of the heavier, coarse-grained material which settled out fairly quickly, while the remainder, approximately 1 720 000 m3, was the fine-grained material which flowed downstream for some distance (VPP, 1859 - 60). From these figures it can be assumed that for the ten years during which this volume of puddling was maintained (1854 - 1864) over 5 700 000 m3 of gravels and sands and 17 200 000 m3 of fine-grained sludge had been discharged into and around Bendigo Creek. This was enough to cover an area of over 400 km2 to a depth of 5 cm. By 1859 the problems associated with the sheer volume of sludge being discharged were such that a Royal Commission was appointed to `Enquire into the Best Method of Removing the Sludge from the Gold Fields' (VPP, 1859 - 60). The goldfields referred to were those in the Bendigo area around the township of Sandhurst (now known as Bendigo). The Report of the Commission (VPP, 1859 - 60) stated that: `... inspection of the country bordering upon the course of the Bendigo Creek, to a distance of about fifty miles from Sandhurst . . . ' had revealed that the sludge had ' . . . filled up watercourses and flooded pasture lands . . . '. It also noted that ' . . . even on the plains, thirty or forty miles away from Sandhurst, where the sludge flows thin, and is relieved from its heavier particles, we found it baked into a perfect concrete, and in thicknesses varying up to two feet or more . . . '. The italics were used for emphasis in the original text. As it was considered unlikely that the physical evidence for such widespread inundation would have disappeared completely over the intervening 130 or so years, a project was initiated to locate any evidence of the inundation in the current landscape. If such evidence were to be found, then an estimate could be made of both its extent and its effects on the topography, drainage, and land-use of the inundated area. Extensive field work has determined that over 700 km2 to the north of Bendigo was inundated by the sludge. The area has not been uniformly covered, but has occasional `inliers' which have obviously escaped inundation by being slightly higher than the surrounding areas. Today the sludge is readily identified as a very fine-grained, hard-setting, concrete-like `capping' overlying a well-developed, well-structured, pedal horizon, or in some instances, the gravels and sands of a creek bed. The thickness of the sludge capping varies between a few centimetres and three metres (Peterson, 1996). The buried topography was gently undulating, in direct contrast with the almost unnatural flatness of

Jan 1, 1997

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By T. Watanabe, M. Nakagawa, K. Kimapong

Lap joint of A5083 aluminum alloy and SS400 steel was produced by Friction Stir Welding (FSW) Process. The effect of welding parameters such as rotational speed, traverse speed and tool dimensions on the mechanical properties and the interface microstructures of the joints were investigated. FSW process could successfully produce the lap joint between A5083 aluminum alloy and SS400 steel. The variations of rotational speed, traverse speed and pin depth of a rotating tool gave rise to various characteristic interfaces of the lap joint and had conspicous influences on the joint properties. The increase in hard and brittle intermetallic phase and defects formed at the interface of the joint decreased the mechanical properties such as the shear load of the joint.

Jan 1, 2004

By Joshua Hoffman, Braden Lusk, Kyle Perry

Despite its porous and lightweight characteristics, aluminum mesh is believed to have blast mitigation properties. The current use of the mesh includes fuel tanks for airplanes, boats, and fuel stations as well as light armored vehicles for the military. The mesh acts as an explosion suppressant by preventing fuel tanks from exploding when exposed to an ignition source. More recently, work has been performed to assess the ability of the mesh to mitigate blast pressures produced by high explosives.

Jan 1, 2009

By N. Henderson, J. Weyer, J. F. Brune

"The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization.Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ’old hands’ are retiring and cannot easily be replaced due to limited graduation numbers.Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries."

Jan 1, 2014

By John L. Floyd

A personal computer is a valuable tool for blast design and analysis. Programs designed for the personal computer, such as the electronic spreadsheet, can be used for a wide range of applications. The spreadsheet formats discussed in this paper are used for explosive comparison, inventory/shot records, and timing design analysis. Each template can be adapted to fit the individual needs of the end user. An example of a graphically orientated blast design program, written in the BASIC programming language, is also discussed.

Jan 1, 1987

By Charles W. Villiers

AS is well known, there are large and valuable deposits of coal in British Columbia, both on the mainland and on Vancouver island. These deposits are widely distributed over the Province. The chief sources of supply on the mainland are found in the Fernie and Princeton-Nicola districts and on Vancouver island in the Comox and Nanaimo districts. The coals range from a very high quality bituminous coal to lignite. On the Upper Skeena river there is said to be a very large deposit of anthracite or semi-anthracite, but this field has not been developed. Coal was first discovered in British Columbia on the north end of Vancouver island in the year 1835, but it was not until 1852 that coal mining was seriously undertaken by the Hudson's Bay Company at Nanaimo, where mining has been carried on continuously ever since that date. The production of coal in the Province continued to increase until the year 1910, when the annual output reached its peak at 3,100,000 tons and a total of 7,800 men were employed in the industry. Since 1910, the production has dropped steadily until, in 1934, only 1,347,000 tons of coal were produced and less than 3,000 men were employed. This continued decrease in production has in no way been caused by lack of coal reserves. It has been due entirely to curtailment of markets. I do not propose to discuss coal mining practice in British Columbia, where we have all sorts of mining conditions, including submarine mining. There is no lack of coal supplies for either industrial or domestic purposes, nor is there likely to be any shortage of coal in the Province for many generations. We have our mining troubles, which increase the cost of production, but there are no insuperable difficulties to prevent the extraction of a large and increasing supply of coal. Our main difficulty-in fact our only serious difficulty-is to find a market for our output, and we must consider means which can be evolved not only to conserve our existing markets but also to expand them, at any rate within the boundaries of Canada. I will therefore confine my remarks chiefly to the all-important factor of Markets for our coal.

Jan 1, 1936

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

By Tetsuo Yamazaki

Seafloor massive sulfides (SMS) in the western Pacific have received much attention as resources for gold, silver, copper, zinc, and lead (Lenoble, 2000). Since the end of the 1980s, SMS have been found in the back-arc basin and on oceanic island-arc areas. The typical representatives found are in the Okinawa Trough and on the Izu-Ogasawara Arc near Japan (Halbach et al., 1989; Iizasa et al., 1999), in the Lau Basin and the North Fiji Basin near Fiji (Fouquet et al., 1991; Bendel et al., 1993), and in the East Manus Basin near Papua New Guinea (PNG) (Kia and Lasark, 1999). The higher gold, silver, and copper contents in one of the areas increased the chance for profitable mining operation, which was considered by a private company (Malnic, 2001). The company gathered investment money and announced to start the commercial mining from 2010 (www.nautilusminerals.com). On the basis of geological information of the Sunrise Deposit of the Myojin Knoll on the Izu-Ogasawara Arc (Iizasa et al., 1999) and geotechnical characteristics of SMS (Yamazaki and Park, 2003), some preliminary economic validation analyses of the SMS mining in small production scale were reported by one of the authors (Yamazaki et al., 2003; Yamazaki and Park, 2005; Yamazaki, 2007). The results showed high profitability of the SMS mining.

Jan 1, 2011