Search Documents

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By P Carrasco, E Me, M Campos, J Tapia

Correct sampling practices are of vital importance to the mining industry; key decisions for the business are made on the basis of samples in all the value chain. Geology plays a relevant role in pre- and post-investment stages. Actually the understanding of natural variability is essential for geological modelling, geometallurgical modelling, mine planning, grade and process control. Improper sampling practices obstruct this objective introducing irrelevant variability components, which can cause monumental economic losses. A good approach to accomplish this understanding is the application of heterogeneity and IngamellsÆs tests, which are useful tools to quantify the variability of a certain well-delimited geological unit at different comminution scales. The application of heterogeneity test can help minimise Pierre GyÆs fundamental sampling error and to study the impact of other sampling errors. IngamellÆs test allows us to define the correct mass of sample for chemical analysis. This paper presents the results of several heterogeneity and IngamellsÆs tests done in Chilean porphyry copper deposits that belong to CODELCO Chile (Chuquicamata, Mina Sur, Radomiro Tomic, El Salvador, Andina and Teniente), in different geological units (endogenous oxides, exotic oxides, supergene sulfides and hypogene sulfides) and for several elements (Cut, Cus, Mo and As). These tests, considering the natural variability, have helped us develop accurate sampling protocols to minimise the fundamental error to acceptable levels. A major contribution of these tests (more than 30) is the generation of secure sampling protocols using the highest sampling constant obtained in the tests, for new porphyry copper deposits that donÆt have information given by heterogeneity and IngamellsÆs tests.

Jan 1, 2005

Owing to circumstances which are entirely unavoidable, the cost of rendering to Institute Members the services which they have been ac-customed to expect from the Institute has increased enormously, especi-ally during the past year. The cost of printing has increased 20 per cent. and another 30 per cent. is expected. There is no recourse; the Institute must pay this or cease publishing. The increase for supplies and office force will be very great. Justice to our employees, whose cost for living expenses has risen by leaps and bounds, demands an increase in. wages, wholly aside from the fact that the employees need not and will not stay. The Institute is, therefore, faced with the alternative of greatly re-ducing its service to the members or else of asking from them a small increase in clues. An amendment to the Constitution has been offered by the members increasing the clues to $15 per year, which cannot become effective until 1921. This still leaves us as the engineering society with the lowest annual clues, except only one, whose dues are $15 per year. To help meet the immediate emergency, the Directors have exercised the authority vested in them by the Constitution and By-Laws and requested the members to pay $3.00 for the Transactions to be issued during the year 1920, which is very much less than the cost of publication. It is the opinion of the Board that the members will prefer to pay this slightly additional expense rather than to have the Institute take a backward step in respect to the services which it is rendering, and which has been increasing constantly in amount, as well as in unit cost, during the past seven or eight years.

Jan 12, 1919

Water is required as a key strategic resource in most mining and metallurgical processes and, in some countries, it has become a limiting supply for the development of mining activity. During the last years, mining industry efforts have been successfully focused on water use efficiency in the different processes. However, these efforts will not be sufficient to compensate for the growing demand of mining products and the decrease of ore grades. New efforts should be oriented to the search for alternative water supplies such as sea water, with or without desalinisation, or water harvesting. But to survive this growing pressure and to get a social licence to operate, the mining industry can also assume a proactive attitude and pursue a prominent role in water management at regional and local scale. This paper reviews some of these emerging issues, particularly in the context of the Chilean copper industry.

Jan 1, 2009

By S. Vela, R. M. McKinley, L. A. Carlton

Johnson et al. have described a new well-testing technique that measures formation flow properties between wells.' The technique, called pulse-testing, requires a sequence of rate changes in the flow at one well and measzcrement of the re.rulting pressure changes at an adjacent well with a very sensitive differential pressure gauge. This paper describes an extensive application of the technique in a producing oil field. Pulse-tests on 28 of 45 possible well pairs in the field provided a picture of the areal distribution of reservoir hydraulic diffusivity, trans-missibility and storage. The primary objective in presenting these data is to demonstrate the potential of the methcid for reservoir description. A second objective is to show in three ways the qualitative and quantitative accuracy of reservoir parameters determined from pulse-tests: (I) pulse-test data show a nonuniformity in the field, closely correlating with the oil-water distribution as given by production data: (2) pulse-test values for permeability are comparable with core va1ue.s; and (3) perhaps most important, the field responds to a conventional interference test in the manner in which pulse-test data predict it should. The pulse-testing technique by Johnson et al.' is an ideal source of data for purposes of reservoir description, for it provides a measurement of formation storage S = +ch, hydraulic diffusivity 91 = k/+cp and transmissibility T — This paper describes an application of this method in a producing oil field. Results were analyzed to give numerical values for the parameters 7, T and S. These values were compared with oil-water production data (for the effect of fluid saturation), with core data and with data from an interference test. The reservoir in which the pulse-test survey was run is the result of a structural trap formed by a fault along the east side of a north-south trending anticline. A down-structure aquifer providcs a natural flank water drive for the pool. The producing formation is a dolomitic lime- stone having mainly vugular permeability; the formation oil has a gravity of 29" API with negligible dissolved gas. The field contains 19 wells, all on pump, arranged on 40-acre spacing along the top of the anticline. Fig. 1 shows the location of all these wells except two at the south end of the field. The dashed line on the right-hand side of the figure represents the approximate location of the fault with respect to well positions. Pulse-Test Survey and Analysis of Data A pulse-test requires a pulsing well and a responding well. In the field, changes were made in the rate of flow at the pulsing well by stopping and starting the pump periodically and measuring the corresponding pressure

Jan 1, 1969

By Randal J. Barnes

The January 1988 issue of Engineering and Mining Journal includes two short articles on blasting practices in surface gold mines (Anon., 1988 ; Carr , 1988). A reader of these articles learns, among other things, that a "12 x 13 ft" blasting pattern is used at the Carson Hill Mine, and a "17-ft burden and 18-ft spacing" is used at Echo Bay Mineral's Borealis operation, while at Mascot's Nickel Plate Gold Mine "ore shots are on a 10 x 10 ft" pattern. Like a new edition of the World Book Almanac, these articles are overflowing with useful tidbits of technical data; but, they never mention why the particular blasting patterns were selected. A survey carried out during the Winter of 1988 at six surface gold mines in the western United States also failed to produce a satisfactory answer. The responses from mine planning engineers to the question "why is your blasting pattern X by Y", reduced to "we use X by Y here because we used X by Y at our last operation, and it worked ok." Certainly, with the available decades of experience and professional practice in blast holes design, rock fragmentation in surface mines has been thoroughly investigated. However, and this is the central issue, fragmentation of the rock is not the primary purpose of most rotary drill holes in surface gold mines. Quoting senior mine engineers from companies operating, three of the richest surface gold mines in the world (AMAX Gold, Homestake Mining, and Gold Fields Mining)

Jan 1, 1989

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

By S Juras

To our geologists at Eldorado Gold Corporation, the release of the gold assays on a new ore zone causes a flurry of excitement. But to our metallurgists, that news is often greeted with the question ‘What’s the sulfur grade’? In our company, we operate and manage projects whose end-product will either be auriferous sulfide flotation concentrate or gold doré. Almost all of the steps in the ore processing are related to sulfur (in this paper specifically sulfide sulfur). So why do we geologists wait until late in a project or into production before collecting sulfur data for mine planning and ore control purposes?Gold deposits associated with sulfides commonly use a metallurgical process that begins with a flotation step to recover gold into a smaller mass known as flotation concentrate. Often, this step solely targets the sulfide minerals with gold only coming along for the ‘ride’. As a result, the gold grade in the concentrate is primarily influenced by the ratio of gold to sulfur in the feed. Should this concentrate require a refractory process downstream (eg pressure oxidation), knowing sulfur grade is critical as sulfur controls heat balance in the process. Regardless, we need sulfur models to be as robust as gold models, and created much earlier in the project evaluation process.Sulfur models require quality data collected at the same density as gold samples. Analytical methods must match expected grade ranges and quality assurance quality control (QA/QC) protocols and must be of the same integrity as in use for gold. Sulfur models will then be created by their own data analyses, interpolation protocols and validation. Furthermore, ore control systems should be designed for regular sulfur monitoring to ensure and enhance downstream value. Given time it should become habitual for geologists to likewise ask, ‘And what’s the sulfur grade’, or more specifically, ‘What’s the gold to sulfur ratio’?CITATION:Juras, S, 2017. Sulfur – the new geometallurgical grade in gold-sulfide deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 199–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By H. R. Reed

THE cost of hoisting with electricity in deep mines is a matter about which little information has been published. This paper makes a detailed study of such costs and presents the information in a series of curves. In particular the curves show the cost of hoisting ore from depths varying from 500 to 7000 ft. Vertical with the shaft at 70° incline for the double cylindroconical and double cylindrical drums, the hoists operating balanced, using Ward Leonard and Ilgner-Ward Leonard control, and designed for most economical operation from each depth. Operation with the double cylindrical drum is expanded to cover hoisting from 2000 to 5000 ft. using equipment designed for 5000 ft. and from 4000 to 7000 ft. using equipment designed for, 7000 ft. Additional curves are included to show the ratings of the necessary hoist motors, energy input per hoisting cycle and size of flywheel in tons for complete equalization when the Ilgner-Ward Leonard system is used, also hoisting efficiency. The duty imposed on a mine-hoist motor fluctuates between wide limits during a cycle of operation. The demand on the motor may vary from a large horsepower value' near the beginning of the cycle to a small or a negative demand near the end of the cycle. Such factors as tonnage to be raised per hour, depth of shaft, and balanced or unbalanced opera-tion have such a marked effect on the operating cycle and vary to such an extent for different mines that no set of rules can he formulated for quickly determining the size of the motor required. The duty cycle from which the motor rating is (derived must he determined for each case according to the conditions of the proposed hoisting operations. The motor torque required at the cardinal points of the duty cycle is determined from the moment or torque in pound-feet necessary to raise and lower the load and ropes, accelerate and retard the load, ropes, drum, etc. The torque diagram depends largely upon the type of drum. Two different types of drums, if used on exactly the same duty cycles, may have widely different peak demands and capacities of hoist motors. The essential feature in the design of hoisting drums and in determining

Jan 1, 1937

By M. A. Pipke, C. M. Brown

The semiautogemus grinding circuit at the Utah Mines Ltd., Island Copper operation, located on Vancouver Island, British Columbia, is described. Since startup of the operation in 1971, grinding circuit throughput has been progressively increased from the initial design rate of 90 000 (99,000) to the current average 45 000 t/d (49,600 stpd) of porphyry copper ore. Key developments ad modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1987

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By W. A. Rachinger, C. Graeme-Barber, R. L. Bell, R. C. Gifkins, T. G. Langdon

R. L. Bell. C. Graeme-Barber, and T. G. Langdon (Imperial College. London)— The internal-marker technique developed by Ishida, Mullendore, and Grant has enabled them to make some interesting observations on the role of grain boundary sliding in creep. Certain of their conclusions are supported by our own similar experiments on Magnox AL80 (Mg-0.8 pct Al) specimens containing several markers, full details of which will be published shortly. In particular, we would agree that: 1) Using the internal-marker method, there is little difference between Egb, the contribution made by grain boundary sliding to the total strain, measured at the surface and in the interior of a specimen. 2) The measurement of the change in grain shape during creep leads to an underestimation of the grain strain, and hence an overestimate of Egb.. However, the discrepancies between the values obtained by this method and those obtained using markers are not as great as Tables IV and V of Ishida, Mullendore, and Grant would suggest; see below. The authors' Eq. [I] which is used to compute Egb from the transverse displacement ITt of longitudinal marker lines is not given in the reference quoted,'' where in fact only relations for Egb in terms of the longitudinal displacements of markers were developed. As first pointed out by Gifkins and Gittins,12 a problem arises in the use of longitudinal markers. and we will show that Eq. [1] underestimates Egb in the interior by a factor of 2. In Fig. 12, two grains X and Y have become displaced by the vector AC which lies in the plane of the grain boundary ABCD separating them. A longitudinal marker has been split by this displacement into the two parts LA and CAW. If these were surface grains the transverse displacement, Ut. could be obtained by viewing normal to the "top" surface. If interior, a section through CD parallel to the top surface would show the same result, provided the longitudinal internal markers delineated planes normal to the top surface. (This is an essential feature of the markers not pointed out in the paper.) The important point is that the quantity Ut tan B (=BE=DF) only gives the elongation due to the one component AB of the sliding. The elongation V/tan 8 (=GD) due to the component AD must be added to produce the total elongation resulting from the boundary displacement AC. If the grain boundaries in a poly crystalline specimen are randomly oriented with respect to the stress axis it follows that In the interior of a specimen the two sums depend for any difference simply on the definitions "top'' and "side". On the surface it is possible that the two sums could differ somewhat. In either event it is clear that the authors' Eq. [I] underestimates Egb, and in the interior, and perhaps at the surface also, the appropriate formula is given by The suggested modification probably makes little difference to the comparison between surface and interior values of Egb where both were obtained from marker measurements. For the estimation of the correction becomes extremely important where the boundary contribution is large. In our own work on magnox, for example, we have obtained values of as large as 70 to 80 pct, under conditions of high temperature and low strain rate. The use of planar markers transverse to the stress axis would simplify the comparison between surface and interior behavior, because measurement of the longitudinal offsets Us of these markers could be summed to give the total elongation di-

Jan 1, 1965

By Pablo Andrés Galarza

Si bien la ventilación de minas depende de las condiciones de la naturaleza, en muchos casos, la profundidad de las mismas, requiere de un sistema completo de ventilación forzado. En este sentido, el texto señala el uso de dicho sistema y sus implicancias como la ubicación de la ventilación principal, número de ventiladores auxiliares y otros medios de control como reguladores, tampones y costos de operación. Asimismo comprende la determinación de un método apropiado para la solución de la red y la selección de un sistema económico más efectivo con los objetivos, parámetros e incentivos de la mina.

Nov 8, 1982

G. M. TAYLOR,* Colorado Springs, Co1o.-I do not think the plan outlined in this paper would work at Cripple Creek. Most of our men have had a pretty good education. The Cripple Creek district is a lessee district-I do not think there is one mine operating in Cripple Creek to-day that does not have the leasing system. We have as many men leasing on our property as we have mining and every plan who is working for wages is looking for n lease-everyman has mined for him- self, he has been his on7n boss on n lease, either on our own property or

Jan 1, 1919

The 114th (New York) Meeting of the Institute will be held in the third week of February, 1917. The Committee on Papers and Publications has set Dec: 1, 1916; as the closing date for the receipt of manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committee they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified. While Dec. 1, 1916, is the final closing date, it is a great advantage to get papers in as much before that time as possible as it enables them to be submitted in proof form to their authors. Papers received on or before Nov. 1, 1916, will, as far as possible, be published in the January Bulletin or earlier, thus giving good distribution among the members in advance of tile meeting. The Institute's records show that the discussion of papers is very rnuch better when they are distributed somewhat in advance of the meeting instead of in the Bulletin which goes out immediately preceding the meeting.

Jan 9, 1916

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981

By Milton T. Pana

Computer techniques now have been applied to the solution of a wide variety of scientific and engineering problems in the mining industry, but generally not in great depth in any one area. In mining, the area covered in greatest depth and with the greatest success has probably been mine planning and to a lesser degree production scheduling. A rather comprehensive review of the literature related to mine planning and production scheduling indicates that contributions in these areas have been geographically, as well as organizationally, widespread. Of twenty-six papers reviewed, eleven were from industry, eight from educational institutions, four from computer vendors, two from the Bureau of Mines, and one from a private consultant. The conclusions that can be derived from the literature are: First, the-state-of-the art has advanced to the point that computing ore reserves and developing mining plans with the aid of the computer is now a routine practice; second, the application of the computer to mine planning problems has markedly improved our ability to estimate ore reserves, more accurately define pit limits, and determine an optimum mining sequence. MINE PLANNING The papers in this section deal essentially with the problem of determining the final pit limits of an orebody and the ore reserves associated with a given pit limit. The problem is probably best described by Soderberg25 and more recently by Reibell. 23. There are two techniques currently being applied to this problem by several mining companies: 1) the multiple-cone technique and 2) the Lerch-Grossman algorithm. The multiple-cone technique is the older of the two techniques and has the advantage of being more flexible, allowing an engineer to easily vary pit slopes in different sectors of the design. The technique can also be used to define intermediate pit contours. The Lerch-Grossman algorithm is appealing in that the final solution is given in the form of a true mathematical optimum. The technique is limited, however, in that the size of the blocks in the orebody model are a function of the desired

Jan 1, 1969

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013