Search Documents

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By S. E. Khalafallo

The Bureau of Mines investigated the kinetics of reduction of wustite and magnetite with carbon monoxide. A mechanism was postulated wherein the interaction between gaseous and absorbed carbon monoxide appears to be the rate-determining process. This mechanism fully accounts for the experimental rate equation JL.h relates th velocity of reduction to the pressure of the reducing gas at constant temperature. It also explains the variability of the heat of activation of the reduction process with the state of aggregation of the oxide material. The integrated rate equation is in perfect agreement with the experimental reduction-time curves.

Jan 1, 1966

By L. Cifuentes

Electrodialysis (ED), i.e. a technique based on the effects of electrically charged membranes on ions in solution in an electric field, has been applied to Cu-Fe-As-Sb- H2SO4 electrolytes similar to those used in copper electrorefining and electrowinning operations. The effects of current density, time and species concentration have been studied in a batch ED cell. The technique has shown to be effective in concentrating and separating a range of ions and points to possible new methods of treating copper electrometallurgy effluents.

Jan 1, 1999

By S. Shrivastava

A structure based model has been developed for the prediction of viscosities of K20-B20, melts. These melts exhibit an anomalous behavior of viscosity with continuous variation in B203 content. A maximum and a minimum are observed at low temperatures, which disappear on raising the temperature above the softening range. The addition of K20 to the borate melts causes two opposing phenomena: (1) depolymerization effects and the related breakdown of network structure resulting in the formation of singly bonded oxygens, which weakens the structure and hence causes a decreases in viscosity, and (2) the formation of four coordinated borons (BO4 tetrahedra) which strengthen the structure leading to an increase in the viscosity. The structural changes taking place in these melts on varying the temperature and the alkali content have been reviewed and are incorporated in developing this model. The predicted values are in excellent agreement with the experimental values over the whole temperature and composition range.

Jan 1, 1992

By J. F. McMahon

Introduction The greater portion of the information presented in this paper was obtained in the course of an investigation on clay gathering and its cost in the provinces of Quebec and Ontario (1). For assistance in the preparation of the paper, the writer wishes to record his thanks to Mr. Howells Fréchette, Chief of the Ceramics and Road Materials Division of the Mines Branch. Clays are mineral substances consisting essentially of hydrous aluminium silicate which become plastic when wet, fairly hard when dry, and stony masses when burned to a sufficiently high temperature and re-cooled. Shales are clays which have been indurated by the processes of nature. Millions of tons of clays and shales are won yearly for the production of brick, tile, sewer pipe, drain tile, roofing tile, fire-brick, china-ware, wall and floor tile, cement, and a host of other products. There are certain types of clay which, due to their particular qualities and limited distribution, are mined entirely or in part for sale to manufacturers, and are even exported from one country to another, as for example china-clays or kaolins, utilized in the manufacture of white-wares and in the paper industry, due to their consistent whiteness; ball-clays, utilized in the white-ware industry, due to their bonding power and whiteness; slip-clays, used in the stone-ware industry because of their glazing properties, and in the grinding-wheel industry for their burned bonding properties; and suspension-clays, such as are used in the enamelling industry. However, the great bulk of clays and shales won are used in the production of heavy clay products, and the manufacturer of these generally owns and operates his own deposit of raw material.

Jan 1, 1933

By W. A. Weimer

Australia, the land of the kangaroo, koala, and the platypus, is often referred to as "down under" by people of the Northern Hemisphere. It is a tropical land and has very little freezing and thawing; consequently the in-place rocks are near the surface, exposing some of the unaltered mineralization. This type of geology induces the prospector and miner to search for minerals which lie at his feet (or not far under them), and it is adapted to open cut surface mining. Some of the rules and regulations applicable to exploration and mining in Australia will be interesting and helpful towards understanding acquisitions and control of minerals. They are common and basic to the United Kingdom. Throughout Australia practically all minerals are the property of the Crown (government), and their exploration and exploitation are administered by the state Department of Mines. Surface owners, or land lessees, do not control the minerals. Their mining codes protect the prospector. If a prospector obtains a permit, "miner's right," it entitles him to search for minerals any place within the state, only holding him responsible for damages he may incur in his exploration. If he finds something of interest, he may then apply for an authority to prospect, which gives greater latitude and protection in his work to develop the find. However, he will be obligated to spend a minimum specified amount to exclusively hold an area. He will be required to furnish maps, analyses, and geological data to the Mines Department. Presuming that he has located something economically valuable for mining, he may then apply for a mining lease or be granted a franchise to produce a specific material. It will contain a quantity clause so that the area cannot be held indiscriminately without production of the mineral. The states have Bureaus of Mineral Resources, Geology, and Geophysics that keep constantly abreast of the search for minerals and often do much of the drilling and deep boring to promote geological study for the states.

Jan 1, 1969

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By Aug. J. Jr. Bowie

(Read at the Wilkes-Barre Meeting, May, 1877.) Brief Outline of the General Topography of the Gold Regions of California. THE topographical features of California, as demonstrated by the explorations of the State Geological Survey, are found to be exceedingly simple. Three equidistant parallel lines can be used in conveying a general idea of the physical geography of Central California. A straight or " main axial line," whose course would be north 31° west, passing through the culminating peaks of the Sierra for a distance of five hundred miles, can be assumed as the eastern boundary of the State. A second parallel drawn fifty-five miles west of the " main axial line" will skirt the western base of the Sierra Nevada, along the edge of the foot-hills. A third parallel run equidistant from the second will represent "as nearly as possible the western base of the Coast Ranges." These parallel lines divide the State into three belts, namely, the Sierra, the Great Valley of California, and the Coast Ranges. " This arrangement of the physical features holds good for a length of four hundred miles in the direction of the main axial line, comprising almost the whole of the agricultural and the greater part of the mining districts."* The section of the country which is of immediate interest to the miner is the western slope of the Sierras. These mountains, rising in a short distance from the Sacramento plains to elevations of over seven thousand feet, with occasional peaks ten and twelve thousand feet high, are cut by numerous deep and precipitous gorges or capons, through which drains the immense watershed of the Sierra, supplying the main rivers of the State and ultimately emptying into the Pacific Ocean. Between these capons, ridges or divides are formed, on top of * See vol. i, p. 5, Geological Survey of California. J. D. Whitney, State Geologist.

Jan 1, 1878

Jan 1, 1911

By G. M. Ross, J. A. Scott, C. A. Laamanen, H. Shang

"Indirect recovery and use of waste heat contained in smelter off-gas is proposed to expand regions available for year-round, on-site production of micro-algae–sourced biodiesel, a fuel that could be used in underground machinery. A dynamic model of an off-gas heat exchanger describes capture and distribution of heat into open, external, rectangular micro-algae ponds. Smelter off-gas contains sufficient energy to maintain large-scale micro-algae cultivation pond temperatures above 15°C, even with winter ambient temperatures below –15°C. Results highlight opportunities that could lie in tapping these heat resources to produce renewable biofuels on-site and sequester CO2 while leaving the industrial process unaffected.RÉSUMÉ On propose la récupération et l’utilisation indirectes de la chaleur résiduelle contenue dans les dégagements gazeux des fonderies pour développer les régions se prêtant à une production toute l’année durant et sur place de biodiesel à partir de micro-algues, carburant dont on pourrait se servir pour le matériel d’exploitation souterraine. Un modèle dynamique d’échangeur de chaleur contenue dans les dégagements gazeux décrit le captage et la distribution de la chaleur dans des bassins rectangulaires ouverts de micro-algues en extérieur. Les dégagements gazeux des fonderies contiennent suffisamment d’énergie pour maintenir les températures des grands bassins de culture de micro-algues au-delà de 15°C, même avec des températures ambiantes en hiver inférieures à –15°C. Ces résultats soulignent les possibilités que pourrait offrir l’exploitation de ces sources de chaleur pour la production de biocarburants renouvelables sur place et pour la séquestration de CO2 sans que cela n’ait d’incidence sur le procédé industriel.INTRODUCTIONMicro-algae that grow in water can efficiently convertsolar energy and carbon dioxide into biomass. This biomass can be up to 50% oils (lipids), which can be extracted and converted into biodiesel through transesterification (Demirbas, 2008). Compared to terrestrial plants that produce similar oils (e.g., jatropha, soybean, and rapeseed), micro-algae represent an order of magnitude increase in areal productivity, do not require arable land, and can be continuously harvested (Rawat, Ranjith Kumar, Mutanda, & Bux, 2013). The potential advantages through the production of biodiesel from micro-algae also include sequestration of carbon dioxide, reduced reliance on fossil fuels, and the co-production of other value-added bioproducts."

Jan 1, 2017

By Harold A. Linke

The following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Handbook and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman. Launder Slopes The main object in the study of launder slopes is to provide grade steep enough to prevent "sanding" by a safe margin, and to avoid

Jan 1, 1943

By Thomas L. Linton

The results of an extensive literature review and field experiments regarding the effects detonation of high energy explosive have upon various aquatic organisms are reported. These results were used to modify regulatory permitting criteria in Texas. Three separate field experiments were conducted. In the first study, surface placed charges were used in a marine habitat. In the other two, the charges were placed in drilled holes. In one, which was in a freshwater environment, the drilled holes were filled with drilling mud after placement of the charges. In the second, which was in an estuarine environment the holes were allowed to sit for thirty days prior to detonation to permit natural back-filling to occur by water transported sediments. A variety of aquatic organisms held in wire cages were exposed to detonations. Immediate and long-term effects of the exposure were determined based on external and internal visual observations. Damage to aquatic organisms was found to be reduced by placing the explosives in drilled holes and back-filling the holes prior to detonation of the explosives.

Jan 1, 1997

By Henrik Gudbrandsen, Geir Martin Haarberg, Ana Maria Martinez, Karen S. Osen, Sverre Rolseth

"The Several approaches were tried for developing an electrochemical route for producing high purity silicon from molten salts. K2SiF6 and metallurgical grade silicon were used as the source of silicon. Molten LiF-KF and pure KF with additions of K2SiF6 were used as electrolytes at temperatures from 550 - 900 oC. Silicon was cathodically deposited and anodically dissolved in the fluoride electrolytes. High electrorefining efficiency was obtained for many elements after electrolysis experiments at constant potential or constant current. The main challenge was to reduce the contents of boron and phosphorus. Another difficulty was to remove inclusions of solidified electrolyte. The lowest energy consumption was estimated to be ~ 3 kWh/kg Si, while the best current efficiency for Si deposition was found to be ~ 95 %.IntroductionSilicon is the most important material for photovoltaic power generation devices because of high feasible efficiency, low ecological impact and slow degradation. Development of a new and less expensive route for producing silicon of the desired quality is necessary in order to make solar cells competitive. Electrochemical routes may be an alternative possibility, and many laboratory studies have been reported over the past few decades. Most of the studies have been performed in molten salts, chloride or fluoride, at moderate temperatures so that solid silicon was deposited at the cathode. The production of high purity silicon has shown an annual increase of about 25 %, due to the increasing demand of solar grade silicon (SoG-Si). For future increased use of solar energy it is important to develop alternative, more energy efficient and cheaper processes for SoG-Si production compared to the Siemens process.Common silicon sources have been SiO2 and K2SiF6 for electrowinning and MG-Si in the case of electrorefining. A serious challenge is to find an oxygen evolving anode for electrolytes containing dissolved oxides. Especially at moderate to high temperatures and in molten fluoride electrolytes this is a difficult task.Many experimental results have been reported in molten chloride electrolytes. Nohira et al. [1-3] and Chen et al. [4] cathodically deposited silicon by electrodeoxidation of solid SiO2 in molten CaCl2 by potentiostatic electrolysis. An alternatice approach is to use electrorefining of low-cost metallurgical grade silicon (MGSi) to produce SOG-Si. In previous studies [5], an MG-Si anode was used, and silicon was successfully electrodeposited on a molybdenum wire in a CaCl2 based melt. It was found that the anode was strongly passivated due to the precipitation of silicon. Also, some deposits detached from the molybdenum wire because of the poor adherence to the cathode.Considering the Cu-Si alloy which has a good segregation effect for some impurities, and should not passivate, could be a good candidate anode for electrorefining. [6]."

Jan 1, 2014

By W. Rostoker

A STUDY of the titanium-oxygen system' involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich's work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich's2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

By T Craske, J Sykes, T C. McCuaig, M Jessell, A Trench

The prevalent strategic approach in the mining industry is one of planning. However, it is widely recognised that planning does not work in complex and uncertain situations (Mintzberg, 1994), such as those associated with ‘above ground’ non-technical orebody complexity (Trench, Packey and Sykes, 2014). Mintzberg, Ahlstrand and Lampel (2009) suggest the focus instead should be on strategic ‘thinking and doing’ and using the many ways to think about strategy to make sense of complex, uncertain, and unique situations. They therefore place great value in cognitive flexibility. Scenarios development utilizes several different thinking styles and thus assists with this type of flexible strategic thinking (Figure 1). The ‘Centre for Exploration Targeting (CET) Scenarios’ were developed with the ‘Oxford Scenario Planning Approach’ (OSPA) (Ramírez and Wilkinson, 2016). The OSPA aims more to improve the thinking skills of decision makers, rather than forecasting per se (Wack, 1985a, 1985b). As such, this paper focuses less on the content of the scenarios and instead on the practical value of scenarios in strategizing. CITATION: Sykes, J, Trench, A, McCuaig, T C, Jessell, M and Craske, T, 2018. Strategic thinking about long-term ‘above ground’ orebody complexity using scenarios, in Proceedings Complex Orebodies Conference 2018, pp 60–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A. F. Buddington

INTRODUCTION EVER since a genetic connection between many ore deposits and magmas began to be widely recognized, some two-score years ago, there has been much discussion of the complex and intricate problem of the genetic association of specific kinds of mineralization with specific kinds of igneous rocks. General discussions of the latter problem and pertinent data have been given by S. F. Emmons, Kemp, Lindgren, Niggli, Rastall, Spurr, Vogt, and others. In this paper no attempt is made to deal with mineral deposits genetically associated with volcanic rocks, but only with those presumed to be related to exposed intrusive masses. The writer is indebted to E. S. Bastin, F. F. Grout, Edward Sampson, and to the members of the committee in charge of the preparation of the volume, for a critical reading of the manuscript and many worth-while suggestions.

Jan 1, 1933

By Williams JK, Bolitho BC

Laverton Gold NL (Laverton) is the first junior Australian mining company to establish a viable mining operation in Indonesia. It successfully commissioned the Rawas plant in Sumatra this year with an average anticipated production of 85 000 ounces of gold equivalent (as gold and silver) per year, a feat of which Laverton is justifiably proud.Working in Indonesia and South-East Asia generally is very stressful for juniors and stretches human and financial resources to the limit - more so than in medium to large companies which can absorb the workload in-house more effectively.

Jan 1, 1997

By Charles Barrett

PLASTIC flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following funda-mental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the lattice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals -"grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by vari-ous investigators for more than 25 years, ? yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of mate-rial that was used in the earlier compression experiments1-hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By G. R. Green, R. C. McDonald

The International Nickel Co., Ontario Div. mines, faced with rising production requirements, short labor supply, and ever increasing labor costs turned to mechanized mining for a solution to its problems. The degree of mechanization of ore removal has increased from 1966 with the purchase of the first diesel-powered load-haul-dump (LHD) machine to the present, with over 53% of all underground production handled by these units. Keeping pace with mechanized ore removal, there has been a parallel development of drilling equipment to complement the mucking units. This paper deals with the applications and economic advantages of mechanized drilling at the underground mines of Inco, Ontario Div. It covers the use of various types of mechanized drills in such mining methods as cut-and-fill, induced block caving, and sublevel caving. The economics of raise boring are also discussed.

Jan 1, 1974

By K R. Sharpe, A Davitt

CXA is currently evaluating, in co-operation with Inco Metals, a new idea in small diameter hole blasting - the Unidelay Nonel initiation system. In concept, the Unidelay system is a hybrid of the conventional multi-period Nonel system and the safety fuse assembly/igniter cord system. It combines the operational advantages of the latter, simplicity and flexibility, with those of the former, safety and compatibility with all commercial explosives.

Jan 1, 1982