Search Documents

Process Study on Some Ag-Cu-Pb-Zn Polymetallic Ore in South China

Sep 13, 2010

By Henry M. Howe

in Cast-Iron. It has been generally accepted that the presence of silicon in cast-iron leads to the formation of graphite; and this has been explained by saying that the silicon lowers the solvent power of iron for carbon at and somewhat below the freezing-point, so that, in the presence of silicon, the iron is unable to retain in solution or combination the whole of the carbon with which it has united while molten, and therefore expels the excess of carbon in the form of graphite, during and immediately after solidification. Probably the best way to study this question would be to examine pure cast-irons, i.e., those containing nothing but iron, carbon and silicon, which at the same time should have been saturated with carbon when molten. But the data for such a study are not at hand; so we must turn to commercial pig-irons as they are made in the blast-furnace, and before their composition has been changed by remelting. Much evidence has been offered of late, tending to oppose the theory of the action of silicon above set forth. Some of this evidence will be examined here. 1. Mr. Bachman's Results. In particular, Mr. F. E. Bachman† has published a collection of analyses of cast-iron, in which the proportion of graphite at first appears to be nearly independent of the proportion of silicon present. Thus, in his Table LI., we find that with pro-

Jan 1, 1901

By Lawson P. Entwistle

One of the important reserves of mangani-ferous iron ore is at Boston Hill, near Silver City, New Mexico. The area consists of a faulted block of gently dipping Lower Paleozoic shale, dolomite, limestone and sandstone, which has been intruded by a roughly circular mass of quartz-bearing monzonite porphyry and subordinate dikes. Prom a noselike protuherance of the intrusion radiate many premineral faults, which have localized much of the hypogene mineralization. Three important stages of hypogene mineralization can be recognized: (I) mesitite, a manganiferous iron magnesite, (2) quartz sulphides, and (3) barite-galena The carbonate stage is widespread but stronger near the intrusion. The quartz may have been derived from hydrothermal alteration of the igneous rocks. Barite-galena is most important in the Chloride Flat mining district, about one mile north, where argentiferous galena provided silver for the supergene ore. The hypogene carbonate, lean in iron and manganese, has been oxidized and consequently enriched by meteoric waters containing an excess of oxygen and carbon dioxide to form ore bodies of intimately mixed hematite and pyrolusite. The ore bodies, at one place attaining a length of 1600 ft., a width of 300 ft., and a thickness of 25 ft., are largely confined to areas of brecciation and to spreads from faults in Silurian dolomite beneath soft Devonian shale. Boston Hill comprises three rolling hills southwest of and adjoining the town of Silver City (pop. 5044), Grant County, N. Mex. The mining district covers less than 2 sq. miles. Silver City, on a branch line of the Atchison, Topeka, and Santa Fe Railway, is a supply point for the important mining communities at Santa Rita, Hurley, Hanover, Tyrone, and Mogollon. The Chloride Flat mining district adjoins Boston Hill on the north. History and Production Bonanza-type silver ores were discovered in the Chloride Flat mining district during the silver boom of the seventies and eighties, at which period it has been credited with as much as $5,000,000 production. In 1916 manganiferous iron ore was first shipped from the Boston Hill mining district to Pueblo, Colo., where it was mixed with manganese ore from Lead-ville and smelted into spiegeleisen. During 1926 and 1927 the Colorado Fuel and Iron Co. mined and churn-drilled part of the district. Mining operations ceased during the depression of the thirties, but production was resumed in 1937. Since 1916 the Boston Hill mining district has produced about 600,000 long tons of ore averaging about 12 per cent manganese and 35 to 40 per cent iron.

Jan 1, 1949

By Frederick Bloetscher

Means of improving the U.S. Bureau of Mines Brattice Window Method have been investigated by Goodyear Aerospace Corporation (GAC). An extensive series of laboratory tests at GAC and a series of tests in three operating coal mines of the Bethlehem Mines Corporation were conducted. The GAC laboratory tests defined the window coefficients and the accuracy of the method using different measuring techniques for a range of window sizes and shapes with window areas from 0.0873 to 4.0 square feet for flow velocities through the windows of from 100 to 1000 FPM. The results indicated that for the range of window sizes and window flow velocities investigated a single window coefficient value can be used with little error for each window size and for each flow direction, for the investigated range of window flow velocities. The mine tests developed techniques for quickly erecting the Temporary Test Stopping (TTS) in a cross-out, making the measurements, taking down the TTS and moving it and the test equipment to the next cross-cut. The time period for the total cycle ranged from 15-45 minutes depending on the properties of the cross-cut's surfaces. The total weight of the TTS and test equipment carried by the two miners conducting the tests was approximately 40 pounds. Correlation was obtained between the sum of the leakage values past 10 consecutive individual stoppings using the brattice window method and the value for the difference in the airway flow values before and after the 10 consecutive stoppings when the value for the sum of the leakages for the 10 was significant when com¬pared to the airway flow values. The mine tests reiterated the importance of using the largest TTS window(s) consistant with making accurate anemometer measurements for the best results with the brattice window method.

Jan 1, 1978

It took the US coal industry 55 years to increase domestic coal production by about 11%-from 568 million tpy in 1920 to today's level of about 630 million tpy. With such a growth record, it would take a few hundred years to double coal production. FEA planners think that it can be doubled in 10 years. "With all the obstacles continuously imposed on coal, the industry's real problem is not growth but survival," says Ray Albrechtsen, board chairman of Mountain States Resources Corp., and "we should consider ourselves lucky if, by 1985, the coal industry won't have been legislated and regulated out of existence."

Jan 5, 1975

By G. J. Hutchins

Precision surface mining is gaining traction in the iron ore, copper, iodine, limestone, bauxite, coal and gypsum markets. In this paper, we first address the possible improvements of a surface miner control using GPS techniques. An application in an iron ore mine in Western Australia is presented. The second item addressed is improvements of a new drum driving technique for a 100 ton surface miner. This technique involves installing a slow speed hydrostatic motor directly on the cutting drum rather than driving the drum through chain and sprockets. Details of the performance of this direct-drive versus the chain-drive are detailed. In addition to the 100 ton machine, we also present a 200 ton surface miner. This larger machine has 1600 hp (894.8 kg), and has been successfully introduced into a large iron ore mine in Western Australia. Performance of the 200 ton surface mining machine in various rock hardnesses is detailed. Some comments on the cost effectiveness of using a built-in loader versus loading with wheel loaders are included.

Aug 1, 2013

By Marcelo Chuaqui

We certainly have the data to back calculate it. I must admit that I haven't, at the moment my priority is not on what is the stiffness of the jet grout but is making sure that the jet grout is really there. It's a bit like what Stuart Littlejohn was talking about this morning in terms of grouting on the dams a small window causes a big problem so it's having the jet grouting there at all, at the moment must have been my focus rather than just what is the stiffness once you've got it there.

Feb 10, 2003

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

Develop an easy-to-use, reliable, resin-grouted cable support system capable of being installed as primary and secondary roof support in coal mines.

Jan 1, 1994

By B. G. Klugh

(New York Meeting, February, 1913.) THE present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglormer-ating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials-to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the applica-tion of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with materials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited tune allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace.

Jan 5, 1913

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986

By Virgil J. Stachura, Larry R. Fletcher, Matthew N. Plis

Falls of ground remain a leading cause of fatalities and injuries in underground mines. In response to this situation, the Bureau of Mines conducted a series of experiments in the White Pine room-and-pillar copper mine which resulted in smoother, safer ribs due to a reduction in the amount of overbreak caused by blasting. The tests evaluated the effects of changes in the loading of the rib holes of the mine's 20- by 28-ft drift round driven in shale and sandstone. The relative integrity of the ribs remaining after the blasts was measured using both photographic and seismic refraction techniques.

Jan 1, 1989

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By Chris Haycocks

The relevant literature concerning ground control, mine planning and reserve conservation in multi- seam mining is reviewed. Factors affecting interaction, interaction mechanisms, and design guidelines are presented in detail. The impact of multi-seam mining on future mining, measures for ameliorating negative interaction effects, and future research needs are also discussed.

Jan 1, 1990

By Aníbal Gastañaga Coll

El objetivo del texto es evaluar el problema de los accidentes ocurridos en las minas del Perú a través de un estudio que se realizó a 3,191 mineros de diversas zonas del país, los cuales fueron evaluados por Instituto de Salud ocupacional por una supuesta enfermedad ocupacional. Dicho grupo de trabajadores presentaron reclamos por una indemnización a causa de una enfermedad ocupacional y no por accidentes, considerándolo como muestra para ciertos estudios del problema de accidentes. Asimismo se analizó el tiempo perdido por los obreros accidentados, las lesiones sufridas de 1109 accidentados, el aspecto económico y los costos de la incapacidad del trabajador. En conclusión, se encontró que el 47.1% de los accidentes fueron leves y el 52.9% graves, es decir, con menos de 15 días y más de 15 días de incapacidad, respectivamente y se asumió que el costo total de los 1305 accidentes es de S/64'287,000.00.

Aug 20, 1965

By Ricardo Arrarte

El presente texto describe la optimización del método de corte y relleno ascendente en la minería subterránea peruana a través de un modelo matemático matemático que minimiza los volúmenes de roca usando la programación lineal, y tiene como resultado las distancias de ubicación de las rampas, pendientes de las mismas, número de cortes a realizar en el tajeo, radios de curvatura, y otros parámetros adicionales.

Sep 14, 2009

By J. C. Gerdeen

It is of upmost importance to keep the size of the program to a minimum for the computer being used. One way is to reduce the size of the data bank by adjusting the large common array A in the main program (page, line 32) and the statement following the assignment of A. The current value of A is 35001 and is optimized for the UNIVAC computer with 5,000 words of useable storage. Another way to reduce the required storage is to overlay the program. That is, to have in the computer only the subroutines which are being used. In large finite element codes, overlays or segmentation of the program is a necessity. The code presented here has three levels of segments and are presented graphically in the tree in Figure D-1.

Jan 1, 1976

By G. J. Jansen

Introduction The usefulness of microscopes in exploration and ore dressing, problems has been documented for the older generation of mining industry personnel in such publications as Schneiderhohn and Ramdohr (1931). A more recent publication that examines the subject is Process Mineralogy, a conference proceedings of The Metallurgical Society (TMS, 1981). However, it is worthwhile to review some of the principles and advantages of microscopic examination of rocks, ores, and mill products. Transmitted light Microscopists can look at materials in transmitted or reflected light. Studying transmitted light is what is usually meant by petrography. In this method, the light passes through the specimen. The upper polarizing filter can be moved in (crossed nicols) or out (open nicols) of the light path. The specimen can be a thin section, a slice of rock mounted on a glass slide and ground to 30 µm (>400 mesh). Or, it can be a sample of rock or ore crushed to about 70 µm (200 mesh). Transmitted light study is particularly suited to gangue minerals, such as quartz, carbonates, and feldspars, and to the study of alteration processes and products. It has some applications to liberation studies. Minerals are identified in transmitted light by observable and measurable optical parameters, such as cleavage and twinning. Figure 1 is a photomicrograph of the mineral microcline, (original

Jan 8, 1985

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By H. J. McQueen

Pyro-reduction of ores to metal products developed markedly through the industrial revolution into the great depression. Nineteenth century resource and environmental sustainability were haphazardly improved by many process changes, although the motivation was primarily reduction in labor, feed stocks and fuel. Some notable achievements were coke and hot air for blast furnaces (later from waste heat stoves), puddling of wrought iron and steel ingot production with convertors advancing into oxygen use and continuous slab, billet and strip casting. Although advances in one sector were often counteracted by fall-backs in others, there was progress in that the resource consumption and pollution per unit of production was decreased. Improvements in the 2 decades following WW2 were mixed but popular notice of environmental hazards forced governments to legislate pollution controls and initiate steps in resource conservation. The energy crisis of the 1970’s saw an industrial energy-saving campaign and legislation of technology assessment procedures. Up until mid 18th Century, the training of iron masters depended on apprenticeship with some formalized knowledge from medieval books such as those of Biringuccio (1540) and Agricola (1556). The advances were very slow partly due to absence of scientific concepts of the smelting process. Nevertheless, some iron masters succeeded in improving the process and described procedures to instruct others. With the surge of steam power and the reverberatory puddling process for ductile wrought iron (WI), machinery changed from wood (iron strap reinforced) to WI machinery. With the clarification of the reduction and oxidation mechanisms by Cavendish and Lavoisier (~1780), productivity in iron production surged. The mechanical testing and microscopy of Kirkaldy (1862) spurred understanding of processing and properties of WI and steel. The various forms of C in steels were determined by chemists at the end of the 19th Century. It also became possible to control metal and slag chemistry in the open hearth furnace. But understanding of the transformations during heat treatment of steel only came in the first decades of the 20th Century.

Jan 1, 2012