Search Documents

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By Pierre Choquet

"The whole work carried out both in situ and in laboratory by a research group of the West German collieries is presented. This work has led to a design method of steel arch supports for gate roadways that gives full satisfaction in this particular coalfield. The method accounts for mining depth, the mining system (advancing or retreating), thickness of the coal seam and other parameters.Full statistics are then given on gate roadway supports of the ECCS (European Community for Coal and Steel) coalfields. They were collected by the author in order to show that the West German method can be applied to other coalfields as the long wall systems which are generally being used are very similar. Design calculations are conducted for each coalfield's case. They show that the method would have been able to predict in most cases the support actually used.Utilization of the design method is recommended to the Cape Breton Development Corporation 's mine operators because mining conditions, even though different from European ones, present a number of similarities which make it possible to apply the design method to their particular case.This procedure might be profitable in mines facing support problems in their levels and for any planning of future projects"

Jan 1, 1986

By D. B. Robinson, J. Lukacs

A knowledge of the equilibrium water content of hydrocarbon systems under pressure is important to the natural gas industry. The information available on the solubility of water in hydrocarbon, hydrogen sulfide, and carbon dioxide systems is reviewed in this paper and the influence of the more important variables such as temperature, pressure and molecular structure on solubility in liquids and gases is discussed. A suitable cbromatographic technique has been developed for determining low concentrations of water. Tailing of the water peaks has been elim inated by adding water to the carrier gas stream The method is applicable for both gas or liquid samples and is effective in the presence of hydrogen sulfide. The experimental study of water solubility in methane-hydrogen sulfide systems at a temperature of 16oF has shown that the presence of hydrogen sulfide causes only a modest increase in water content at pressures up to 1,400 psia. Theoretical considerations and data on pure hydrogen sulfide and carbon dioxide suggest that the effect of both these compounds will be greater at higher pressures and in the liquid phase. INTRODUCTION Before transporting or processing natural gases and gas condensates, it is usually necessary to dry them using suitable dehydration equipment. The design and operation of this equipment requires a knowledge of the amount of water present in the fluid at the reservoir and operating conditions. This is influenced by temperature, pressure and composition, particular1y when certain non-hydrocarbon components are present. Field experience indicates that hydrogen sulfide and carbon dioxide, for example, alter the usual water solubility relationships appreciably. However, an extensive search of the literature does not reveal any quantitative data on such systems. For sweet natural gases, generalized empirical correlations such as the one proposed by Katz, et al,6 can be used to predict water solubility with confidence at most temperatures and pressures of interest. However, existing theoretical relationships do not permit a calculation of the deviation from these curves when polar substances like hydrogen sulfide are present in the system. Thus one must resort to an experimental approach to obtain the necessary information. The fact that laboratory experimental methods frequently involve the use of mercury which reacts with hydrogen sulfide in the presence of water, and that hydrogen sulfide interferes with many chemical reactions specific for water has contributed to the difficulty of studying water solubility in systems containing hydrogen sulfide. In this investigation the water content of a limited member of methane-hydrogen sulfide mixtures was determined using a special technique with gas chromatography. REVIEW OF PUBLISHED DATA Experimentally determined water solubility data have been reported for methane, 14 ethane, 15 propane, 9 n-butane, 16 1-butene, 11 hydrogen sulfide 18 and carbon dioxide. 19 These studies report the effect of pressure, temperature and molecular structure on water solubility in single component gases and liquids. Fig. 1 compares experimentally determined water solubilities in several hydrocarbons, carbon dioxide and hydrogen sulfide at l00F as taken from this

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By R. B. Sudderth

The recovery of copper by various combinations of processes centered around liquid ion exchange has certainly been accepted as a technically superior entity when compared to the widely applied classical method of cementation. While the technical aspect of liquid ion exchange processes has received much attention and acclaim through actual operating data, in particular the ease of handling solutions, percentage recovery, reduction of pollution, etc., the corresponding economic data has either gone unpublished or has been held confidential. Much of this economic data has now been made available for publication; and with this data, we at General Mills Chemicals, Inc., will attempt to present an accurate economic analysis of some liquid ion exchange plants and an economic comparison between these plants and the typical cementation facility.

Jan 1, 1974

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

The new field of environmental investiga tions introduces new problems of ethics, res- ponsibility, conflict of interest and technical procedures. Such investigations involve four elements: developer, consultant, approving authority and the public. It is essential that the consultant provide technical competence, speed and efficiency, impartiality and credibi- lity. Despite allegations to the contrary, it is not in the consultant's own best interest to omit, ignore or obscure significant adverse en vironmental impacts.

Jan 1, 1975

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By Alhondra de los Santos, Jesús L. Valenzuela, Jose R. Parga

"The present study evaluated the feasibility of using iron species generated by electrocoagulation (EC) as an adsorbent for removal As(III/As(V) from aqueous media. The full potential of EC was evident in that more than 99 percent of arsenic was removed without addition of chemical reagents. The adsorbent iron-species generated by EC was characterized by Chemical Analyses, X-Ray Diffraction and Scanning Electron Microscopy. The experimental data were correlated by employing a Langmuir adsorption isotherm. Thermodynamic parameters such as ?H o , ?S o and ?Go were calculated. The adsorption process was found to be exothermic and spontaneous.1. IntroductionArsenic contamination in potable water supplies is a serious health problem in many countries around the world. Groundwater arsenic contamination in La Comarca Lagunera Mexico was first reported 30 years ago [1]. Arsenic concentration has been found in well water from several communities ranging from 0.25 to 1.0 ppm. The elevated concentration of arsenic in water, above that originating from natural sources, has been attributed to the use of organoarsenical pesticides in the cotton fields and also to the millions of tons of waste slag generated at a local lead smelter [1]. The main arsenic species present in natural waters are arsenate ions 3- 4 AsO (oxidation state V) and arsenic ions H3AsO3, - 2 3 H AsO and 2- 3 HAsO oxidation state III). However, As(V) ions are most prevalent in oxygenated water while As(III) is found for anaerobic conditions, such as in well water or in groundwater. Conventional methods of arsenic removal rely on chemical-based treatment with lime, alum coagulation, iron coagulation and chemical oxidation. Other processes used with varying degrees of success include adsorption onto activated carbon, reverse osmosis, nanofiltration, manganese dioxide, magnetite and ionexchange resins [1-3]. These conventional processes generate a considerable quantity of secondary hazardous waste such as solid sludge, which also pose serious environmental problems. These drawbacks have forced various industries to search for effective, alternative treatment technologies for arsenic with a preference for electrochemical methods."

Jan 1, 2008

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1995

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

Systematic ICPES (Inductively coupled plasma emmission spectrometry) analysis of magnetic concentrates from drainage samples has been used to discriminate concentrates dominated by magnetite from those dominated by pisolites, presumably maghemite-rich. In addition, a set of spurious zinc enhancements was recognised and explained with the help of mineralogical data, and systematically isolated using chromium as a Discriminator.

Jan 1, 1987

Lake Superior Iron Ore Association, 3100 East 45th St , Cleveland, Ohio W L Tinker, Secretary This Association does not issue scientific technical bulletins, strictly speaking, but statements, etc , are published containing information of interest to mining engineers and geologists To show the type of information published, mention may be made of material issued in 1931: 1 Directory of mine operators and statistical data. 2 A bulletin, Distribution of Lake Superior iron ores, also Eastern and foreign ore 3 A booklet, Analyses of Lake Superior iron ores, season 1931 These publications, or information on others may be had by addressing the above

Jan 1, 1933

By J. Mantilla, J. Calizaya, J. Frisancho

"La mina Tantahuatay; es un deposito epitermal de alta sulfuración Au-Ag, en perforaciones recientes de extensión por sulfuros, se ha determinado zonas de Skarn al NE del tajo Tantahuatay 2, ubicado políticamente Chugur, Cajamarca, Perú. Los trabajos de perforación 2016, nos han permitido reconocer nuevos cuerpos mineralizados asociados a zonas de Skarn, con leyes de (0.30 g/t Au y 0.4% Cu), emplazados en las formaciones Chulec (calizas), Inca (sedimentos), Farrat (cuarcitas). Los ensamble de alteración analizados son Yeso, Clorita, Epidota, Paragonita, algunos de estos minerales poseen una concentración anómala de REE. Indicativos de una gradación sistema alta sulfuración a Skarn."

May 1, 2008

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

By Jin Zigang

In China there are more than 30 coal fields menaced by karst-confined water. In the north and east of China there are many collieries which mine coal seams of the Carboniferous and Permian Systems, which are above the Ordovician limestone (general thickness is 500-600 meters). Ordovician limestone is full of karst fissures, contains a lot of water under high pressure (15-65 kg/cm2) near the commercial coal seams (20-80 meters), the water easily infiltrates the thin lime- stone at the point of the structure crevice, so water-irruptions from the floor are the main source of water-related disasters in these coal fields. According to the statistics there were more than 300 accidents of all kinds of water-irruptions from the floor in these fields since the beginning of their development. It is of great significance in developing coal production in the eastern part of China to solve the problem of safe mining of the seams menaced by the karst-confined water of the Ordovician limestone. The research on this subject consists of three parts: (1) investigating the geological structure and hydrogeological conditions of each mine of the mining area; (2) researching the mechanism of water-irruptions from the floor and proposing reliable methods to predict and monitor; (3) improving the mining system and proposing a mining plan with safety precautions against water-caused accidents. The chief task is to research the mechanisms involved and to discover the causes and conditions of the phenomenon. The authors have obtained some findings on this subject in the last five years, making use of the comprehensive observation and research system, which will be discussed under three headings.

Jan 1, 1984