Search Documents

By C. H. Hobbs

A recently completed series of projects funded by the Commonwealth of Virginia and the U.S. Minerals Management Service was designed to assess the distribution of heavy minerals on the inner continental shelf adjacent to Virginia. These projects indicate that a suite of minerals of both strategic and economic interest is present. Analysis of several hundred grab and core samples shows that zircon, monazite, and titanium minerals (ilmenite, rutile, and leucoxene) occur in quantities that probably warrant further study by the mineral industry. Furthermore, side-scan sonography and shallow seismic profiles have provided information on the thickness and areal extent of the mineral-bearing sands. Possible development of the resource is enhanced by a potential use of offshore sand for beach nourishment. The results of the preliminary studies have been presented in open-file publications and oral reports in order that the mineral industry might have an up to date basis upon which to consider more exploratory work. Much of the effort south of the mouth of Chesapeake Bay was made in cooperation with and enhanced by an independent study of sand resources for beach nourishment and other needs. Preliminary review of the quantitative analyses of the heavy-mineral content of several hundred samples demonstrates that the distribution of high concentrations is non-uniform. From core data, the greatest abundances of some economic heavy minerals (ilmenite, rutile, leucoxene, monazite, and

Jan 1, 1988

By R. Rosenblum, J. Y. Kim, D. Shink, K. G. Stowe

"A small scale continuous flotation cell was designed and constructed at the Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine.This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results. INTRODUCTIONStudy of the behaviour of an ore during concentration by flotation process starts, in general, with a series of tests in laboratory cells. Given the discontinuous nature of these tests, the information obtained by such a study is somewhat limited. It has long been recognized that laboratory test results are not always reproducible in pilot plant tests and subsequently, the pilot plant results do not always predict plant performance. The differences are often blamed on batch vs continuous operations, grinding media, size distribution, aging (oxidation), water quality, equipment, operator's skills, etc."

Jan 1, 1992

By E. O. Wagner, V. F. Parry, J. B. Goodman

C. P. HEINER*—If you take out 35 pct of the total weight of the coal in the form of moisture, would that be about what it was in the case of North Dakota lignites ? V. F. PARRY (authors' reply)—That is about it. C. P. HEINER—That will be about a 35 pct loss and the final product will be about 11,000 Btu? V. F. PARRY—That is right. The heating value of the dried lignite is 10,000 to 11,000 Btu. C. P. HEINER—And the thought is not, then, to produce a commercial coal with that heavy loss, but to make other products—that is, synthetic fuel base, is that it? V. F. PARRY—The principal thought is to upgrade the coal, making it a more favorable raw material for industrial purposes, both for shipment and direct use. You see, the trouble in these lignites is that their moisture penalizes their

Jan 1, 1950

By J. M. Snook, F. C. Langenberg

FOR a better understanding of the melting and refining processes, the oxygen content of the steel bath should be determined. The oxygen content influences many process and product variables such as the efficiency of alloy recoveries, the ingot structure (through reaction with carbon in the steel), certain reaction rates, cleanliness (formation of indigenous oxide inclusions), and mechanical properties. Many methods of sampling liquid steel for oxygen have been devised. These methods can be divided into two main groups: 1) taking samples directly in the furnace or ladle;'-'0 2) removing the metal from the furnace or ladle in a sampling spoon and pouring it into a mold, or drawing the metal from the spoon into a sample holder.11-l4 The advantages and disadvantages of the two general sampling methods are presented in Table I. The bomb-sampling technique described by Huff, Bailey, and Richards8 has been used by the Crucible Steel Co. in certain research projects where oxygen contents were needed. It was recognized that a localized boiling condition could result when the mold is introduced into the steel bath, although the work of Gilbert and Bailey9 seems to indicate that the carbon boil occurring in the bomb-sampler cavity has a negligible effect on the oxygen content. In order to confirm the reported negligible effect of a carbon boil, additional work was done with adaptations of the conventional bomb sampler. The methods used are shown in Fig. 1 and are as follows: 1) Type A: aluminum wire (0.125-in. diam) coil in cavity; steel cap over mouth 2) Type B: aluminum cup in cavity; aluminum cap over mouth, 3) Type C: aluminum cup in cavity; steel cap over mouth, 4) Type D: fine aluminum wire (0.013-in. diam) in cavity; steel cap over mouth. The amount of aluminum wire in the Type A and D samples varied from 0.8 to 1.2 pct of the sample weight. The aluminum cups averaged 2.0 pct of the sample weight; the latter were used to ensure that the steel contacting the walls of the bomb cavity was fully killed. Samples were taken from plain carbon heats made in open-hearth furnaces. This grade of steel before silicon additions is essentially an Fe-C alloy and the effects of other alloying elements on the oxygen activity can be neglected. The results of sampling with the bomb samplers is shown in Fig. 2 where the percent oxygen is plotted against the percent carbon on log-log paper. Spoon sample results on the same grade of steel where the sample was killed in the spoon are shown in Fig. 3. The oxygen contents were determined by the vacuum fusion method. A comparison of Figs. 2 and 3 shows that the oxygen concentrations obtained with the spoon-sampling method (metal killed in the spoon after slag removed

Jan 1, 1960

By Stephen C. Tadolini

The anchorage capacity of four types of bolting systems was investigated in two mines with thick coal roofs. In conjunction with the in-mine tests, a simple axisymmetric finite element computer program was developed. Both the field and computer results indicated that thick coal roofs can be effectively supported entirely by the coal member.

Jan 1, 1986

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

Phase equilibria have been determined experimentally for pseudo-ternary sections of the form ?MnO?-(CaO+MgO)-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.17 and MgO/CaO weight ratios of 0.25 and 0.17 respectively for temperatures in the range 1473-1673 K. The primary phase fields present for the MgO/CaO weight ratio of 0.17 include manganosite (Mn,Mg,Ca)O; dicalcium silicate a-2(Ca,Mg,Mn)O?SiO2; merwinite 3CaO·(Mg,Mn)O·2SiO2; wollastonite [(Ca,Mg,Mn)O?SiO2]; diopside [(CaO,MgO,MnO,Al2O3)?SiO2]; tridymite (SiO2); tephroite [2(Mn,Mg)O?SiO2]; rhodonite [(Mn,Mg)O?SiO2] and melilite [2CaO?(MgO,MnO,Al2O3)?2(SiO2,Al2O3)]. For the section with MgO/CaO weight ratio of 0.25 the anorthite phase (CaO·Al2O3·2SiO2) is also present. The liquidus temperatures of ferro- and silico-manganese smelting slags have been determined. The liquidus temperatures at low MnO concentrations are shown to be principally dependent on the modified basicity weight ratio (CaO+MgO)/(SiO2+Al2O3).

Jan 1, 2004

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012

By F. C. Bond

History The breaking and shaping of rock was one of man's earliest occupations. In the Paleolithic Age long before the dawn of history, arrow¬smiths and the makers of stone axes, hammers, knives, scrapers, spears, and borers were highly respected members of society. In early historical times stones for building blocks, roads, and city walls were shaped by slaves and convicts, who also did most of the mining. However, great artists erected beautiful stone sculptures, while gifted architects planned imposing temples and monuments. Until well into the 19th century nearly all rock was broken laboriously by hand. The small rock required by John MacAdam for his macadamized roads in England in the 1820s was produced by women and boys seated alongside the roadside with hand hammers and legs wrapped with rags. Eli Whitney Blake, a nephew of the Eli Whitney who invented the cotton gin, developed the first successful jaw crusher before 1870. The gyratory conical crusher soon followed. Comparative tests established its large capacity advantage over the jaw crusher, as well as its greater cost for a given feed size. Both types have been in use for more than 100 years. Crushing rolls appeared before 1900. Thomas A. Edison made very large diameter rolls which were excessively long; they failed because of shaft deflection. Various types of disk crushers and edge runner rolls appeared about this time. The older methods of reducing rock were adaptations of other processes. The stamp battery of dropping weights effected crushing by simulating heavy hammer blows; the much earlier arrastre, in which heavy stones were dragged in a circular path over the ore by animal power, came from the prehistoric method of grinding grain between two rubbing stones, while the jaw crusher was adapted from simple squeezing devices. But the tumbling grinding mill was not just an adaptation; it was an invention, because it required thinking on a somewhat higher order-there was no prototype. Its nearest antecedents were probably the small closed tumbling drums used in England more than a century ago for cleaning and polishing small iron castings. The date of the first tumbling mill actually used to grind rock is unknown, but it was later than the American Civil War (1861¬1865). It was almost certainly a closed or batch mill in which rock was placed and rotated until it reached the desired particle size. It could have been operated either wet or dry. The first published refer¬ence to such a batch mill was one introduced by Alsing in England (1870) for the grinding of calcined flints for pottery work.21 There are several rather indefinite reports of grinding mills in the early 1890s, including an overflow ball mill in the Helena and Livingstone reduction plant in Montana which may have been the first of its kind. 11 Many of the first mills, which were called tube mills, used hard rock both as grinding media and as mill lining. The rock used was preferably stone from the Normandy and Danish beaches, when it could be imported. This remarkable siliceous stone was already widely used for grist mills throughout America, and its resistance to wear was greatly respected. The decade of the 1890s saw the development of tumbling mills with continuous feed and discharge and their extension into different industrial uses. By 1895 some experience had been accumulated. Iron grinding balls were being tested and the proper speed of rotation was being determined. The Clark Patent tube mill was featured in an E. P. Allis bulletin of 1890, which may have been the first published description of a tube mill. More than 1,000 Gates tube mills had been built by Allis-Chalmers before 1913. Many of these were used in gold mining, espe¬cially in South Africa. The 5 x 22-ft size was particularly favored for grinding portland cement; the use of tumbling mills in the manufac¬ture of cement began about 1900. A great deal of attention was paid to the mill lining. Metal was then relatively expensive, and the general approach was to trap some of the rock grinding media into mill lining pockets. This rock would then absorb the wear and protect the metal lining. In the first ten years of the 20th century there were several different types of pocketed liners, with different manufacturers advancing the superior claims of their patented arrangements. The Osborne liner, developed in South Africa, was probably the most successful. 21 Another item which attracted much attention was size classifica¬tion within the mill and in ancillary equipment attached to the mill and rotating with it. The Krupp type, with interior screens protected inside the mill lining, was developed quite early in Germany, possibly before 1890. The Dorr reciprocating rake classifier (1907) had not yet been invented, and many strange and impractical screening and classifying devices were proposed. In these unsatisfactory machines the two separate processes of size reduction and classification were combined into one operation. It was many years before recognition came that a machine is most efficient when it is designed for one specific purpose. There was much industrial wastage before the opera¬tions of grinding and classification were finally separated. After 1900 the grinding of portland cement raw material and of cement clinker required large numbers of tumbling mills. Most of the raw material was then ground dry. This was also the heyday of gold mining. The old stamp mills that were used in great numbers for grinding gold ore did not grind sufficiently fine to liberate all of the gold, and the new tube mills were installed following the stamps. After 1910 larger diameter tum¬bling mills with larger grinding media were developed. These could receive the finely crushed ore directly, and the inefficient stamp batter¬ies were gradually eliminated. The Rand in South Africa was the greatest gold producer, treating immense quantities of rather low-grade but consistently free milling gold ore. The first tumbling mills, or tube mills, went into operation there in 1904. They were so successful that within a few years no new stamp batteries were installed in the district, even though old ones continued to pound away until after 1950.3 The early tube mills on the Rand all employed Normandy or Danish pebbles, which had to be imported at considerable expense. Their reported wear was as low as 4 lb per ton ground. 4 Many of the mills were lined with the same tough Danish stone cemented into place, while others used the pocketed steel Osborne liner. It was in 1907 on the Rand that an important test was made using hard native ore for grinding media in place of the expensive imported pebbles. 3 This ore, called banket, did not wear as well as the renowned Danish pebbles, but the cost per ton of grinding was definitely reduced. Many of the tube mills on the Rand were soon grinding with native ore. This was the beginning of the development now called autogenous grinding, in which the ore grinds itself. This is treated under a separate heading. See Subsection 3C, Chapter 4. Gold mining was important in America also, and its grinding history follows that of the Rand. Danish pebbles were replaced by native ore in Santa Gertrudis, Mexico, in 1913, 4 and in Consolidated Gold Fields, Nevada, in 1914. 5 Other properties followed suit. However, it gradually became apparent that the capacity of a given mill could be almost doubled if rock grinding media were re¬placed by cast iron or steel grinding balls. In order to increase plant grinding capacity many rock media mills were converted to iron grind¬ing media in the second decade of the present century. In some mills the motor size was doubled; other mills were cut in two and another motor was provided for the second half. Grinding mills began to assume a more modern appearance. Crushing rolls were formerly much used following crushing in jaw or gyratory crushers and preceding grinding in ball mills. How¬ever, the roll surfaces wore rapidly, and skilled maintenance was required to obtain even wear. Rod mills could take feed of the same crusher product size and reduce it finer. The first rod mill was con¬structed by Mine and Smelter Supply Co. and was tested in Canada

Jan 1, 1985

A. W. TRACY' AND D. H. THOMPSON (presented in written form).-Messrs. Ed¬munds, Anderson and Waring are to be commended for their excellent work in so painstakingly reducing to constants, the variables believed to be associated with these types of stress corrosion. An ammonia stress-cracking apparatus similar in many respects to the one described has been assembled. Certain aspects of its construction may be of interest. Tensile loading of the specimens, which are usually Y8-in. diameter wires, is accomplished by springs acting in compression in compact, portable, tubular assemblies weighing less than 10 lb. The lower end of each assembly contains the test specimen and is passed into the test chamber for exposure to the moist ammoniacal atmosphere. There is considerable convenience in being able to load the specimens in a portable unit, which may be warmed to prevent condensation, and then thrust instantaneously into the test chamber. Spring loading obviates the use of weights, but it has the disadvantage of allowing some relaxation of the load if the specimen elongates during corrosion. The maximum loss in load found so far was 20 per cent. The air supplied to the test chamber is humidified by passing it through thermo¬statically controlled water. The air is dispersed into fine bubbles by being forced through a porous ceramic filter at the bottom of a tank containing about 10 liters of water. The temperature of the water is controlled independently of the tempera¬ture of the test chamber. Thus, with the

Jan 1, 1945

By Cyril Wells, Robert F. Mehl

THE two earlier papers in this series1,2 presented data on the rate of diffusion of carbon and of manganese in gamma iron. Apart from their scientific interest, these [] data are needed chiefly in order to treat data on carburization, on the rate of formation of pearlite, and on the rate of austenizing in a quantitative way. 1,2,9,10 In the present investigation rates of diffusion of nickel in -?-Fe over wide temperature and concentration ranges have been determined, and the effects of carbon, of impurities, and of grain size on these rates have been studied. Claussen,3 using the data of Fry,4 has calculated the diffusion coefficient of nickel [ ] in -?-Fe as 9.2 X 10-11 sq. cm. per sec. at 1200T., but had no data from which to calculate the variation of D with concentration, temperature, and percentage of carbon. METHOD AND MATERIALS Method.-Nickel was diffused along the axis of a cylindrical specimen across a concentration gradient, concentration-penetration curves were determined and D values calculated from Grube or Matano solutions.5 Details of the method are given

Jan 1, 1941

By Johnson RD

The variation in coal properties and the coal seam reduced level can be analysed using partial trend-surface analysis techniques. For the area studied seam reduced level and seam thickness data from the Bulli Coal yield trend-surfaces with a high coefficient of determination, since they have relatively small systematic local and random components in their overall variation. Sulphur content appears to have no significant re.gi_onal trend, and phosphorus content has a very weak regional trend. Other analytical variables have regional trends which are of intermediate strength. The strike-directions of.the statistically significant first degree! trend-surface are similar, sug-gesting.: that the variation of the several coal properties was controlled by a set of- related causes. The relations apparent from the dip and strike of the first degree trend-surfaces are similar to- those which are apparent from the trend- surface residuals and'from the results' of canonical trend-surface analysis.'.. It is probable that differential subsidence controlled the areal

Jan 1, 1975

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By Ashraf A. M. A. Wali

Many of the economic resources of Egypt have been recognized and exploited for thousands of years (e.g. gold and copper). Most of these minerals, particularly those from hard-rock sited deposits, are found in complex form along with other components while those present in sedimentary sequences are largely in simple compounds or as native elements. Recognition of their characteristic settings (structure, basin development, environment of formation etc.) is the main clue in predicting and locating their presence. The main economic minerals exploited in Egypt today come from sedimentary sequences and include sodium and potassium chlorides, gypsum, sulfur, and sedimentary iron ores. Large amounts of low grade sedimentary phosphates are known but are not of economic value at today's prices. Recent intensive investigation in the north-eastern Sinai (EI Arish) and along the southern coasts of the Gulf of Suez has revealed new and extensive sulfur and chloride deposits, and considerable oil and gas are now being exploited from closely related sediments. Tin is the only mineral that is produced from hard-rock sources, and gold and copper deposits are present but not of high enough grade to be economically viable. However, a significant part of Egypt has not yet been studied in enough detail to close the door on future discoveries. Another point of considerable geological interest is the presence of diverse, modern evaporitic settings, from which we may draw the analogs for many of the older gypsum, anhydrite, chloride and sulfur de-posits. In fact these analogs are so well displayed that both the Sinai and Gulf of Suez-Red Sea evaporites (Middle and Upper Miocene) can be readily compared with these modern deposits.

Jan 1, 1990

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By C. van der Merwe, R. Lumbule, J. Kgomo

"The mining industry in the Democratic Republic of Congo has seen a significant expansion in copper and cobalt production in recent years. The greater proportion of this expansion has arisen through processing of oxide ores. The design of metallurgical processes for these oxide ores is based on the conventional equipment and layout for processing of sulphide ores, and comprises milling followed by leaching, solvent extraction, and electrowinning. The physical characteristics of the oxide ores, however, provide the process design engineer with an opportunity to examine critically the principles on which equipment selection is based and to design processes better suited to these ores. In 2015, ERG Africa began a project to expand the leaching capacity of the Luita hydrometallurgical facility. A number of innovative changes to the conventional process design were included in the modified flow sheet, which were validated when the project reached design throughput in November 2017. Of these changes, the most novel presented an alternative approach to mitigate the impact of colloidal silica on the operation of the solvent extraction plant. Introduction ERG Africa operates the Luita hydrometallurgical facility located at Kakanda in the Democratic Republic of Congo (DRC), treating malachite and heterogenite minerals to recover copper as electrowon cathode and cobalt as a hydroxide precipitate. The process was originally conceived as a heap leach operation followed by direct electrowinning of copper, with solvent extraction (SX) and electrowinning (EW) of cobalt. In preparing the sized ore for the heap leach operations, the undersized ore fraction at a P80 of 625 µm was discharged to a fines storage facility for later processing. This fraction carried with it approximately 30% of the copper contained in the run-of-mine (ROM) ore feed, and an equivalent proportion of cobalt.In a subsequent development, the cobalt SX section was converted to a copper SX facility, the leached cobalt being recovered from a bleed stream from the copper heap leach circuit. The operating cost for the process as then installed placed this facility well in the fourth quartile of the industry cost curve. The initial Luita operation was established in 2010 at a time when metal prices were above long-term averages (copper above US$3.00 per pound; cobalt above US$20.00 per pound), and the drop in prices in 2015/2016 presented a major challenge. The London Metal Exchange (LME) copper price dropped below US$2.00 per pound, with cobalt dropping below US$10.00 per pound in Q1 2016. This set in motion a range of improvement initiatives for the Luita operation. Central to this was the installation of a tank leach circuit to process the discarded fines and a modified SX circuit to manage colloidal silica. The revised Luita circuit reached design capacity in November 2017 and has proven to be well suited to processing of the oxide ore feed. This process design challenges the boundaries of conventional thinking in the areas of leaching, solid/liquid separation, solution management, impurity management, and metal recovery, and is the subject of this paper."

Nov 1, 2018

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002