Search Documents

By I. R. Kramer

In his technical note entitled "Specimen Temperature During Electropolishing of Aluminum Crystals" Dr. Nakada 1 reported that the temperature of his aluminum specimen increased 65°C when it was polished electrolytically; he therefore concluded that the temperature of the specimens used in our work (Nakada's Refs. 4 and 5) similarly increased by this amount. From this he further concluded that the change in plastic-flow characteristics associated with the removal of the surface by electropolishing during deformation were due solely to a temperature effect. We believe that these conclusions are not justified. It is, of course, realized that the amount of the temperature increase is associated with the total heat transfer of the entire system, including the efficiency of the stirring action, heat flow through the grip on the specimen, and so forth. Of great importance is the type of electrolyte used for polishing. For example, in Dr. Nakada's experiment a methanol-perchloric acid solution was used. This solution has a relatively low conductivity and for the current densities of 0.3 amp per sq cm the electrical input appears to be 30 to 40 w. In our research a methanol-nitric acid solution was employed and for the size of specimen employed by Dr. Nakada the power never exceeded 7 w. There are major differences in his test apparatus which also appear to affect the temperature rise. In our case a steel specimen holder was used in order to provide a good heat sink and conduction path. The cathode was a coiled aluminum tube through which a coolant was passed to provide additional cooling capacity near the specimen. The stirrer was placed in a position to obtain maximum cooling efficiency. On the other hand Dr. Nakada used a teflon grip to support the specimen at one end only and a flat copper cathode, thus providing a much less efficient heat sink as compared with the metal grips used in our studies. The relationship between current density and the temperature increase for two sizes of aluminum crystals tested in our tensile apparatus is shown in Fig. 1. The temperature measurements were determined from a thermocouple spot-welded to the surface of the specimen. The thermocouple was protected from the acid by means of a thin film of stop-off lacquer which covered just the outer surface of the thermocouple junction. Whereas Dr. Nakada reported a time delay of 8 min to obtain thermal equilibrium, our temperature change occurred in less than 15 sec. This emphasizes the importance of the heat transfer in the entire system. However, readings were taken over a period in excess of 5 min to assure thermal equilibrium. The data given in Fig. 1 were also confirmed by determining the thermal expansion of the specimen in a sensitive creep apparatus. As may be seen, for the smaller specimen the increase in temperature is 8°C for a current density of 1.5 amp per sq in. The majority of our data on the effects of surface removal on the plastic behavior of aluminum were obtained at current-density values at or below this value. Above 1.5 amp per sq in. the temperature rise is uncertain; for under certain conditions, especially in the vicinity of 2 amp per sq in., the anode can become polarized and the current flow is erratic. This condition is easily recognized because wide fluctuations in the creep and stress-strain data make it virtually impossible to obtain reliable results, a condition which was always avoided in our work. The temperature increase for the larger specimen is less than that of the smaller specimens below a current density of 1.5 amp per sq in. At a current density of 2 amp per sq in. the temperature increased 13°C. The above temperature data are in accord with observations made during creep experiments. Using a transducer capable of detecting strain in the order of 10 -6, temperature changes in excess of 8°C were not detected when the current density was increased to as high a value as 1.5 amp per sq in. Finally we wish to point out that our experimental data cannot be explained solely in terms of a heat effect. For example in Fig. 1 of Ref. 2, the change in slope of Stage II as a function of the rate of re-

Jan 1, 1965

This paper examines the operational characteristics and requirements of crushers and screens. Several possible control loops are considered and it is shown how these can be used to satisfy particular requirements.

Jan 1, 1978

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By A. Luszczkiewicz

This paper presents the beneficial effects of non-oxidative leaching of final and intermediate copper sulfide concentrates with sulfuric acid prior to the final cleaning stage of flotation. This unique process, combining leaching and flotation, appears to be advantageous for difficult-to-treat carbonate-bearing Polish copper ores, such as those processed in copper concentrators at KGHM Polish Copper. It was shown that after the chemical decomposition of about 70 % of the total carbonates naturally present in the flotation feed, a considerable enhancement of subsequent flotation results (both grade and recovery). The resulting products of non-oxidative leaching are solid hydrated calcium sulfate (gypsum), soluble magnesium sulfate and gaseous carbon dioxide. The beneficial effect established by the laboratory leaching tests was subsequently confirmed during a pilot plant operation treating final copper concentrate and a problematic intermediate concentrate at the Lubin concentrator.

Jan 1, 2007

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By H Y. Fang, H Sutherland, R M. Koerner

Due to the increased number of complaints by property owners to blasting related industries an apparent need for a clearer understanding of blasting-related damage is needed. We feel that direct structural crack monitoring during such blasts is the appropriate measurement technique. Instrumentation and interpretation of results for taking such measurements are described in this paper. Typical results from blasting and other environmental effects are also described which can eventually be related to Fracture Mechanics principles in the hope of clarifying such disputes in an equitable manner.

Jan 1, 1976

"Reports are sometimes heard of one ill effects of pneumatic tools on the hands of workmen. In consequence of such reports, Dr. Francis M. Barnes, Jr., M..D. of St. Louis, Missouri, was retained by the operators to make an investigation of conditions in the Bedford, Indiana, region, and the result of this investigation was published the Journal of the Missouri State Medical Association, Volume 16, February 1919. A brief review of this report may be of interest to all users of pneumatic tools, or operators of plants where such tools are employed.The investigation was made during December 1917, and involved an examination of general working conditions, and a careful physical examination of stoneworkers who had long used pneumatic tools. As the Bedford district is the most important structural limestone producing center in the country, the results of this investigation may be regarded as fairly conclusive as to the general effect of pneumatic tools on limestone workers."

Jan 1, 1920

By Daniel W. H. Su

Current longwall pillar design relies heavily upon past experience and many assumptions about pillar and entry response to longwall abutment pressures. Caving characteristics of the immediate and main roof strata are known to play an important role in the overall pressure redistribution, which determines the maximum abutment pressure, abutment pressure at the T-junction, and the width of influence zone. This paper presents the results of an extensive geomechanical study in a longwall panel at a West Virginia coal mine. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed by the instrumented locations. Overburden response to longwall mining was also monitored, and height of the highly fractured zone above the gob was determined by postmining drilling. Good agreement was observed between the measured stress changes and those computed using the known height of the highly fractured zone. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining.

Jan 1, 1987

By Paul Chamberlin

Management has assorted roles to play, many of which are listed, that may call for consultant input. Consultants also play various roles, and some of these are discussed as well. The relationship between management and the consultant depends mainly on management's preparation for the assignment and on their monitoring during the assignment. Consultant costs are discussed briefly and suggestions for keeping consultant costs under control are given. In addition, some qualities of a good consultant are covered.

Jan 1, 2001

By Robert Palmer

So MUCH has already been written on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have, come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place.

Jan 1, 1930

By Joseph D. Martinez

Salt, because of its plasticity, exerts a major influence in deformation. Resulting salt structures are common world-wide. A special type, salt domes, are associated with thick sequences of sediments deposited over salt. Their upward intrusion is generally thought to be in response to buoyancy. Mines in salt domes reveal an internal pattern compatible with large amounts of vertical flowage. Caprock, the end product of accumulation of anhydrite from salt dissolution, attests to long continued upward growth and concomitant truncation by moving underground waters. Concepts of modes of growth are evaluated and related to problems in utilization.

Jan 1, 1979

By Ricardo Dr. Chavez, Mathieu Lachamp, Rob Dr. Farnfield

Pueblo Viejo is an open pit gold mine in the Dominican Republic which is always looking forward to implement the newest technology in the industry to improve all processes. Focusing on one of the pillars of the department and our company, digitalization, we’ve been looking for the technologies that allow us the automation of data generation, supervision and process innovation. That’s where a new Drill and Blast software takes place, helping to integrate the process from the beginning to end, right after the pattern is designed until it’s blasted, allowing us to track results like vibration, fragmentation, performance, cost and inventory of each blast in a single platform. The software helps engineers to generate back analysis by blast, bench, pit, month and many other ways, in a timely friendly manner. Therefore, we can catch business opportunities and improvement for the drilling and blasting process.

Jan 1, 2019

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By John Boardman

THE latest metal-mine accident report available for the United States is that of the Bureau of Mines for the calendar year 1919. Quoting from Table 20, p. 53, of that report, we find that there were 468 men killed, 7 permanently totally disabled, 321 permanently partially disabled, 7848 injured seriously (more than 14 days disability), and 23,330 of 1 to 14 days disability. We have no records to show what the average days lost per case of accident is, but the records for the Anaconda Copper Mining Co. show that, leaving out the fatalities and total permanent disabilities, and counting those in which the lost time was one or more days, the actual days lost due to accidents, for the Butte mines and shops for five years, 1917-1921, were as follows: Accident Statistics, Butte Mines and Shops of A. C. M. Co. Rate Shifts Days Lost Year Accidents Total Shifts 10,000 Shifts Days Lost Per Acci-dent 1917 2,661 3,169,720 8.395 26,734 10.05 1918 2,765 3,545,149 7.799 39,199 14.17 1919 1,381 1,853,143 7.452 22,797 16.50 1920 1,376 1,879,410 7.321 20,164 14.65 1921 376 776,461 4.842 8,287 22.03 Total... 8,559 11,223,883 7.625 117,981 13.80 In order to place an economic value. on this loss, we will assume that all the 468 fatalities and the 7 total permanently disabled in the United States were com-pensated for at the rate which applies in the State of Montana, that is, $5000 each, and that the 8169 serious accidents in the United States were compensated for at an average of $70 per case, thus bringing the estimated compensation paid by metal-mining companies in the United States to the enormous total of $2,946,830 for the year 1919. The figure of $70 per case was obtained by dividing the total amount paid by metal-mining companies under Plan No. 1 of the Montana Compensation Law, for the first five years of its operation, by the total number of serious accidents for those years.

Jan 9, 1922

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By T. J. Dudek

To be competitive in automotive applications, polymer composites must be processable by high production rate processes like injection molding (IM), reaction injection molding (RIM), structural rim (SRIM) and compression molding. With current fiber reinforced composite materials, performance properties are sometimes compromised to make them compatible with these processes. This is done by decreasing the amount and length of the reinforcing fiber and the viscosity and molecular weight of the polymer matrix. Sheet molding composite (SMC) and thermoplastic polymer blends are examples of polymer composites which are cost effective in many applications and meet the high speed processing requirements for automotive parts.

Jan 1, 1993

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

By Burks WG, Hughes FE, Muceniekas E, Whitcher IG

The area containing the iron field, recognised by the writers, is part of an uplifted, portion of the 'Western Australian Plateau,' ranging in elevation from about 1,000 feet to about 3000 feet above sea level. The local rock succession is flat-lying or moderately-folded and belongs to the Nullagine Series of Upper (2). Precambrian age. This series forms the Hamersley Rangeland vast portions of the...

Jan 1, 1964