Search Documents

By W. D. Forgeng, P. F. Wieser

MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.

Jan 1, 1964

In 2005, a total of 4,490 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.6% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,039; 45.4%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Of all states, Pennsylvania had the most stone mines (n=379; 8.4%).

Jan 1, 2008

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By A. W. Schlechten, Ernest J. Breton Jr.

Experiments on the separation of copper and zinc ions by selective action of ion exchange resins showed the carboxylic type to be more effective than the sulphonic resins. The latter demonstrated a greater capacity over a wider pH range. Data show the effectiveness of resins as a means of concentration. IN recent years the restrictions of stream pollution laws and the high price of metals have created an interest in ion exchange as a means for metal recovery. Some applications have proved successful. In Germany during World War 11, 17 tons of copper per day were recovered from rayon mill wastes by means of ion exchange resins;' and for some time in this country a large ion exchange unit has been in operation for the recovery of copper from rayon waste water. The possibilities of applying ion exchange to the recovery of metals occurring in plating rinse water is particularly promising. In most of these applications only the metal being recovered occurs in the waste. The ion exchange resins act merely as a means of concentrating the metals to a point where they can be recirculated. It would be highly desirable to use ion exchange as a means of not only concentrating but also of separating metals. With the exception of the impressive separations accomplished in connection with the atomic energy program, very little has been done on metal separations.' Therefore, an investigation was undertaken at the Missouri School of Mines and Metallurgy to determine if either of the two main types of ion exchange resins could be used to separate metal ions in solution. The selective removal of copper ions from a mixture of copper and zinc on carboxylic and sulphonic-type resins was investigated as a function of flow rate, pH, copper-zinc ratio, and concentration. It was shown that zinc can be separated from copper and that very large ratios of concentration can be obtained using ion exchange resins. Since ion exchange is relatively new to the field of metallurgy, a brief review of the subject will be included. Theory of Ion Exchange A comprehensive theory for ion exchange has not been developed as yet, but the mechanisms are analogous to metathetical reactions: R Na + Cu++ *=? K(SO3)2 Cu + 2Na+ R is the designation for the ion exchange resin. If a copper solution is passed over a resin bed in the sodium form, two ions of sodium will be released for every ion of copper removed. For the most part this reaction follows the laws of mass action and of electrical neutrality. Consequently, if an excess of sodium ions is passed over a bed containing copper, the reactions will be reversed, and the resin will be regenerated to its original form. A few empirical rules governing the exchange reaction have been set forth: 1—In general ions with a high valence will replace ions with a lower valence. 2—Ions having higher activity coefficients have a higher replacement potential. 3—In a series of mono-valent ions, those with the smallest radii of hydra-tion will tend to replace those having larger radii of hydration. 4—Where ions are similar in most respects, those with the higher atomic weight sometimes will take precedence. This last rule is not as definite as some of the others. These rules apply to rather dilute solutions at moderate temperatures and assume all ions to be present in about equal concentrations. Higher concentrations and temperatures may in some cases reverse the normal exchange reactions. Ion exchange materials are unique in that their efficiency increases as the concentration of the solution decreases. For many exchangers, most efficient operation is obtained at concentrations in the order of one thousandths of a percent. Most applications, though, are made in solutions containing considerably higher concentrations than this. Coste9 as shown that ion exchange resins will remove aluminum and iron effectively' from solutions of up to 10 pct chromic acid. Ion Exchange Resins Ion exchange resins are insoluble, porous, resinous structures to which active groups have been attached. Active groups such as (—SO,,)- and (COO)- pick up cations; hence structures saturated with groups such as these are called cation exchangers. Structures saturated with groups such as (—NH,)' which pick up anions, are referred to as anion exchangers. The resinous structure of necessity is resistant to strong acids, bases, oxidizing, and reducing agents, and most of the common organic solvents. An idea of the stability can be gaged from the fact that resins last for many years under constant use without detectable chemical or physical breakdown. The ion exchange reaction is not confined to the surface of these synthetic resins. Its porous structure permits active groups in the center of a particle as well as those on the surface to remove ions. A high capacity resin such as Amberlite IR-120 will remove up to 3.3 lb Cu per cu ft of resin. In this investigation several approaches to the problem of separating copper from zinc by ion exchange were considered. First, if a reagent could be found which would complex one of these metals and not the other, then by passing this reagent through a bed of exchanger containing copper and zinc, the

Jan 1, 1952

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

The paper discusses how automation is steadily proceeding throughout all areas of the electrolytic zinc industry. Fluid bed roasters with integral sulphuric acid plants are now on -computer control. Highly efficient, continuous leaching and purification stages, with feed-forward predictive and optimisation computer control, precede electrolytic cells with on-stream solution analysers and automatic stripping of deposited zinc. Controlled electric induction furnaces feed continuous casting lines, equipped with automatic stacking and strapping, machines, after computer based metal analysis has confirmed metal purity or alloy composition. The paper also discusses the use of computer models tied to process control systems, and the equipment and solution measurements that could be automated with advantage, using modern micro-based controllers and analysers.

Jan 1, 1985

By E. J. Roberts, E. B. Fitch

Most classifiers in use today are, in function, settling pools. A fluid suspension of particles is passed through a pool at such a rate that only a fraction of the particles-the coarser fraction-has time to settle out of suspension. The rest are carried on out of the pool as overflow. The most fundamental way in which such classifiers differ is in the mechanism used to remove the settled particles from the pool. The particles may gravitate from the pool, as in the various sand cones, or they may be conveyed mechanically from the pool by drags, spirals, or reciprocating rakes. The mechanism of settling pool classification and its limitations are discussed. A method for calculating countercurrent classifications is presented. The practical validity of the calculation method has been confirmed through 20 years of use within The Dorr Co. During this time it has been used on diverse feeds and has been checked against many types of settling pool classifiers, with close agreement in nearly every case. Excellent elimination of third critical mesh particles and finer ones may be obtained in a countercurrent classifications series where all stages separate at the same mesh, but elimination of first and second criticals is inherently limited. Spectacular elimination of all criticals may be obtained by arranging successive stages to classify at successively coarser mesh. Improvement in elimination is obtained at the cost of an increased internal recirculation, but this may be tolerable in many cases.

Nov 1, 1956

By P. Chu, J. A. Finch, R. Li

"Bubble size plays a key role in flotation. In this paper, we examine the possibility of using passive acoustic sending to determine bubble size. Software was developed based on Short Time Fourier Transformation (STFT) to analyze the frequency of the acoustic signal emitted from the bubble formation event. Bubble size was determined from the Minnaert frequency. The acoustic-determined bubble size responded to reagent dosage, but was less sensitive than that given by imaging. The constraints of the current acoustic approach are discussed.INTRODUCTIONBubble size is an important factor affecting flotation performance. It determines the maximum available surface area for collecting and transporting mineral particles. Of interest for process control (Gorain, Franzidis, & Manlapig, 1995), it can be determined by several techniques, such as image analysis (Grau & Heiskanen, 2002; Hernandez-Aguilar, Gomez, & Finch, 2002); conductivity (Barigou & Greaves, 1992); drift flux analysis using gas rate and gas holdup measurements (Banisi & Finch, 1994); and optical sensors (Randall, Goodall, Fairlamb, Dold, & Connor, 1989). However, all these techniques have drawbacks.Acoustic analysis of the oscillatory behaviour of bubbles to extract bubble size is another possibility (Leighton & Walton, 1987; Pandit, Varley, Thorpe, & Davidson, 1992; Al-Masry, Ali, & Aqeel, 2005; Manasseh & Ooi, 2009; Leighton & White, 2012; Spencer et al., 2012). The fundamental basis is the work of Minnaert (1933) who first correlated the bubble size with its natural frequency, Equation 1:"

Jan 1, 2016

By John C. Branner

Inquiries are frequently made concerning the chalk- and clay-beds of Arkansas, usually with a view to the manufacture of Portland cement. The chalk-deposits were first described by Professor R. T. Hill in the annual report of the Geological Survey of Arkansas for 1888, vol. ii., pp. 153-162. Since the publication of that report I have visited localities then unknown, and have accumulated considerable additional information concerning these deposits, dl of which is brought together in the present paper. My report upon the clays of the State has never been published; only a few of the more conveniently available deposits are mentioned in the present paper. The Chalk-Deposits. Stratigraphic Position of the Chalk.—The chalk-deposits of Arkansas belong to rocks of Cretaceous age. The Cretaceous rocks are confined to a single definite area in Southwest Arkansas. Beginning on the Ouachita river, a little northeast of Arkadelphia, its southern or upper margin follows a line about five miles southeast of, and approximately parallel to, the St. Louis, Iron Mountain and Southern Railway from Arkadelphia

Jan 1, 1898

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By Linneas W. Laage

The purpose of this report is to document the fire experiments conducted at the Waldo Mine, NM during March 1990. The U.S. Bureau of Mines is concerned with improving and validating the predictive capability of the mine ventilation and fire simulator, MFJRE. To accomplish this, fire experiments were conducted at the Waldo Mine and temperature profiles were developed as functions of time and distance from the fire. These tests then provided data for verifying the heat transfer model in the MFIRE mine ventilation and fire simulator. An initial analysis of this data indicates that it will serve this purpose well. This report summarizes the data obtained during six fire tests at the Waldo Mine.

Jan 1, 1994

By Jack Bedder, Nils Backeberg

"Native antimony metal is rare and antimony generally occurs together with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main economic mineral.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. While China remains the leading primary producer, accounting for 69 percent (80.5 kt or 88,700 st) of the global 117.5 kt (129,000 st) in 2017, market consolidation and regulatory inspections across China leading to closures of facilities have caused a significant decrease in Chinese output from 115.8 kt (127,600 st) in 2015 (81 percent of global production).Tajikistan and Russia are the next largest producers of antimony after China, both ramping up production in recent years. Russia could significantly increase its supply of antimony if Polyus moves ahead with supplying 10-12 kt/a (11,000–13,200 stpy) of contained antimony from gold tailings. Australia and Bolivia are also significant mine producers outside China. The value of the different ores varies based on the metal content of the concentrates, with the most valuable gold-bearing ores sourced from Australia’s Costerfield Mine and the least valuable mercury-bearing ores sourced from the Anzob Mine in Tajikistan. On average, Bolivian and Russian ores trade at an intermediate value between those from Costerfield and Anzob. Nearly all of the rest-of-world production is exported to China, where the ores and concentrates are processed into antimony ingots and oxides.Antimony ingot production is not as widespread as is the case with antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries ,such as Vietnam and Myanmar, where environmental legislation has historically been less stringent. Tajikistan has become a growing producer of antimony ingot since 2014, coming from the commissioned metallurgical plant at the Anzob Mine.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe (mainly Belgium and France), which relies on imported antimony metal feedstock, mostly from China.A new antimony project under construction by Strategic and Precious Metals Processing (SPMP) in Oman made progress in 2016 and 2017, and after producing first metal in April 2016 in test facilities, was set to be commissioned in the first quarter of 2018. Commissioning had been moved back to June 2018, with a potential ramp-up to 2-3 kt/a (2,200 to 3,300 stpy) of antimony metal by the end of 2018. SPMP is also reviewing producing antimony oxide as part of its flow sheet."

Jan 7, 2018

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By Wilford L. Stork

Certain influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,l such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, 'thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is redly burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the . world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book.3 The work of J. E. Johnson, Jr., has revolutionized the metallurgy of cast iron and it seems apparent that all future work must include an oxygen determination just as we include silicon, sul-

Jan 1, 1920

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,' adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953

The following is a discussion of a new approach to safety when developing or applying a new mining technology. In the form of an engineering process, the following approach had its inception in the military and aviation industries and is also very strongly evident in the chemical industry.The process has been developed and applied in the mining industry by the author. It is called 'Incremental Development and Management of New Technology'.The process is a composite of carefully selected System Safety Management, System Engineering and Financial techniques and methods. It consists of modules which can be modified to suit the requirements of a specific project. Modules provide an organised framework of activities to facilitate a gradual acquisition of pertinent knowledge and information and to enable progressive evaluation or verification of produced outcomes against specified requirements.

Jan 1, 1992

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008