Search Documents

The value of U.S. mineral raw material output reached a record $63.1 billion in 1975. This high exceeded the 1974 value of $55.2 billion by 14 percent. Among the three major mineral categories -fuels, metals, and nonmetals -only fuels showed an increase in value. Both the metal and nonmetal categories showed declines in value. The significance of this nearly $63 billion mineral output can be noted in the fact that it is the basis for the subsequent production of over $270 billion a year in energy and processed materials. Of the 78 individual mineral commodities included in these 1975 totals, only 17 registered gains in output, while 45 registered value increases, reflecting higher prices.

Jan 1, 1976

By Kenneth E. Skiff

INTRODUCTION United Nuclear Corporation and Homestake Mining Company are partners in a major uranium mining and milling venture near Grants, New Mexico. The partnership was formerly called Homestake-Sapin Partners and was recently renamed United Nuclear-Homestake Partners (UN-HP). The mill, originally built in 1958, had a capacity of 1,650 tons per day. With subsequent improvements and the addition of the adjacent Homestake - New Mexico Partners mill, the UN-HP mill is currently rated at about 3,500 tons per day. An alkaline type leach process is utilized by the mill. Milling consists of five basic steps: A. Ore handling and preparation B. Extraction C. Solid-liquid separation D. Precipitation and purification E. Product preparation MILLING Ore Handling and Preparation The primary source of ore for the UN-HP mill is from its four

Jan 1, 1983

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By Charles Bohdanowicz

As in preceding years, the most intensive drilling activity during 1934 took place in the old fields of the western part of the Polish Carpathian petroleum province (district of Jaslo). The number of wells completed to the end of 1934, expressed in percentages, is as follows: Jaslo district, 57 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 27; Stanislawow district 8 and Boryslaw fields only 7 per cent. The number of meters drilled (Table 2), expressed in percentages, for the same fields are as follows: Jaslo district, 51 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 26; Stanislawow district, 12, and Boryslaw oil fields, 11 per cent. This comparison shows that most of the new

Jan 1, 1935

By Y. Feng

Perovskite structured oxide 15% Y-doped BaCeO3 (BCY15) has been evaluated for use as proton conducting electrolyte in SOFC with propane as the fuel and Pt as both electrodes. Under the fuel cell conditions, BCY15 exhibited high proton conductivity and good cell performances. Propylene was detected as product at the anode outlet, and the product distribution suggests that propane dehydrogenation underwent competition with cracking to lighter hydrocarbons. Stability during cell performance tests showed that there was no obvious degradation for BCY15 electrolyte during operation of C3H8-O2 fuel cell.

Jan 1, 2005

By P. Yu, L. X. Liu

"A mechanistic model for tumbling mills was developed during PhD studies at the JKMRC. The concept was presented at the IMPC of 2014, followed by progress in a sub-process of the model presented at the IMPC of 2016. Additionally, a number of papers on the sub-models and breakage function have been published. This paper provides a consolidated summary of the outcomes and status of the model. The overall model structure is presented along with the sub-models such as appearance functions, breakage rate functions, energy distribution, transport, and multicomponent grinding interaction model. The strengths and capabilities of the model structure as achieved to date are presented. The gaps in knowledge and sub-processes are also presented, providing a guide to the areas that require further research and development. It is proposed that the approach developed in this paper provides a structure that can accommodate future mechanistic, dynamic mill model evolution that can incorporate the latest research outcomes and provide a platform to test modelling improvements. This can assist in substantially improving the predictive mill modelling capability in the industry, the importance of which should not be underestimated for this workhorse of mineral processing.INTRODUCTION Grinding is almost the largest single energy-consuming process in the mineral processing industry, which was estimated that about 0.2% of global, and 1.3% of Australia’s electricity is consumed by comminution of gold and copper ores (Ballantyne and Powell, 2014). Although there are some relatively new grinding mills, such as stirred mills, vibrating mills and HPGRs (High-Pressure Grinding Rolls), etc., tumbling mills, as the traditional grinding facilities, are more extensively used."

Jan 1, 2018

By D. Bienstock

In connection with air-pollution studies, the Bureau of Mines is cooperating with the U.S. Public Health Service in investigating the use of solids for removing sulfur dioxide in concentrations of less than 0.5 percent from combustion and waste gases. Removal of sulfur dioxide at flue-gas tempera¬tures would no longer result in the cooling of scrubbed gas, which is inherent to liquid scrubbing processes used exclusively in industry today. Results are reported of extensive investigation, using metallic oxides as absorbents, adsorbents, and oxidation catalysts at 130° and 330° C. (temperatures at which flue gas may be treated in powerplant practice). The most active absorbents tested were the oxides of manganese, cobalt, copper, and alkalized alumina; 23 to 33 grams of sulfur dioxidn were removed by 100 grams of absorbent at 130° C., while scrubbing more than 90 percent of the sulfur dioxide from a simulated flue gas, and 19 to 61 grams of sulfur dioxide were removed at 330° C. A more detailed study is reported on absorption and regeneration, using manganese oxides and alkalized alumina. Adsorption of sulfur dioxide on activated carbons and molecular sieves at elevated temperatures is considerably less efficient than removal by absorption--a maximum of 7 to 8 grams of sulfur dioxide could be removed with 100 grams of adsorbent at 130° C. A potash-promoted vanadium pentoxide is effective in converting sulfur dioxide to trioxide; complete conversion in a simulated flue gas containing 0.35 percent sulfur dioxide was obtained at 365° C. Pilot-plant and cost studies are being made by the Bureau to determine the economic feasibility of removing on an industrial scale the sulfur dioxide present in gases in low concentrations.

Jan 1, 1961

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By Eero Pokki

The Päijänne Tunnel is being constructed to conduct raw water from Lake Päijänne to the Helsinki Metropolitan Area. The length of the tunnel will be 120 km and the cross-sectional area is 15.5 sq m. Excavation started in 1973 and will be completed in 1982. 94 km of the tunnel have been constructed from Lake Päijänne towards Helsinki. The construction has advanced according to plan, and due to Finland's hard bedrock there have not been any great surprises. When completed, the tunnel will meet the water requirements of the Helsinki Metropolitan Area for a long time in the future because, with a free fall of 36 m, 9.6 cu m/s of water can be conducted through the tunnel from Lake Päijänne to the Helsinki Area. With pumping it will be possible to obtain a flow of 15 cu m/s, although at first the discharge will only be 5 cu m/s. The tunnel was partly taken into service as early as March 1979 when it was possible to conduct water to the municipalities north of the Helsinki Area. It is already possible now to conduct water to Helsinki, too, but from the Korpimäki pumping station onwards it must be done through the River Vantaa, which is polluted. When the tunnel is completed in 1982, good quality water can be conducted from Lake Päijänne to the Helsinki Metropolitan Area through a continuous rock tunnel. The cost estimate in 1973 was $ 88 million while it is now $ 90 million notwithstanding high inflation. AREAS NEEDED FOR CONSTRUCTION The areas needed for construction were bought through voluntary deals. Areas of 4 - 5 hectares were bought along the tunnel line at about 5 km intervals. The excavation of access tunnels was started from these places, and the crushed rock from the main tunnel was also transported there. However, it was not necessary to buy the area

Jan 1, 1979

By Kenneth L. Cook

THE five serpentine masses exposed within the northern half of Riley County, Fig. 1, constitute a major part of the few exposures of igneous rock in Kansas.' Although not many subsurface data are available for this part of Riley County,2 six deep wellsV indicate that the basement complex lies between 2500 and 3000 ft below the earth's surface. A northwestward-trending ridge in the present basement surface, which extends across the northern half of Riley County, is indicated on Mettner's contour map.' The serpentine masses lie in a region that was active during Pennsylvanian and Permian time along two main tectonic trends, which may, in part at least, have developed contemporaneously." One trend is northeasterly, as evidenced by the Nemaha anticline, the Abilene anticline, the Voshell anticline, and many other smaller northeastward-trending folds. The other trend is northwesterly, as evidenced by the central Kansas uplift, the Salina basin syncline, and smaller northwestward-trending folds. The area of the Abilene anticline was actively deformed during much of this time, and the present surface rocks, for the most part Permian in age, show many normal faults." The Bala and Leonardville intrusions lie within a mile of the axis of the Abilene anticline, Fig. 1, as mapped by Wallace Lee;' the Randolph No. 1 and Randolph No. 2 intrusions lie within about 5 miles of the axis; and the Stockdale intrusion lies within about 8 miles of the axis. The igneous rocks have intruded horizontal or gently dipping limestones and shales that are late Permian in age.V he period of intrusion, according to Moore and Landes, was probably Cretaceous.' At present a detailed description of the petrography is available for only the Bala intrusion. Moore and Haynes' describe the rock at Bala as a green, serpentinized, porphyritic, peridotite breccia containing inclusions of shale. The ground mass consists chiefly of serpentine and calcite with considerable chromite (5 to 10 pct) and some magnetite. The phenocrysts consist principally of altered olivine with some altered augite and biotite. Although probably different in petrographic details, all the serpentine masses are somewhat similar in that 1) they consist of a dark green, fine-grained ground mass of igneous rock containing many xeno-liths composed of fragments of the neighboring sedimentary rock; 2) they tend to form small mounds on the landscape, thus indicating their greater resistance to weathering and erosion; and 3) they are magnetic. Previous Magnetic Survey of the Bala Intrusion: To the writer's knowledge, only the Bala intrusion had been surveyed with a magnetometer prior to the magnetic surveys discussed in this paper. Dreyer8 interprets the intrusion as a vertical, eastward-plunging dike, on the basis of the results of his magnetic survey, Fig. 1, with a vertical magnetom-

Jan 1, 1956

By Tao Cheng

Previous research and applications in construction resource optimization have focused on tracking the location of material and equipment. There is a lack of studies on automated monitoring of the interaction between workers and equipment for safety purposes. This paper presents a new approach for measuring the safety performance of construction personnel particularly when they work in very close proximity to moving equipment as well as static hazards such as chemical and flammable substances. A method of generating hazardous zones according to the geometric and kinematic characteristics of the considered hazard is introduced. The spatio-temporal relationships between the hazardous zones and workers? positioning data collected by real-time location sensing technology are automatically analyzed. This approach has been validated in a controlled test bed environment that simulates a construction site. Results indicate that worker?s safety performance of selected activities can be automatically and reliably measured using the developed approach. Furthermore, a heat map is generated for visualizing proximity related issues in the test bed using the computed results.

Aug 1, 2013

By L. C. Glenn

In the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. Oil in Tennessee A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were produccrs. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that output. Production is from a fissured part of the limestone and varies greatly in accordance with the size and extent of the ramification of the

Jan 1, 1921

Real Time and In Situ Measurement of Elemental Composition Using Lasers

Sep 13, 2010

By H. A. Davies

DURING a current program of research on the structure and properties of liquid sodium alloys, the need arose for information on the solubilities as a function of temperature of several B subgroup metals in liquid sodium. In the absence of reliable information in the literature for several of these systems, par- ticularly at temperatures in the range 100° to 300°C, an apparatus was constructed to determine solubilities by a direct melt-sampling technique, followed by wet-chemical analysis for both sodium and the solute metal. The details of the technique have been described previously.' The solubility of indium in liquid sodium was determined at eight temperatures in the range 100° to 270°C. The solubility as a function of temperature is shown on Fig. 1; this represents the liquidus line over this composition range. A cooling curve was plotted after the completion of the sampling and an arrest was observed at 94.9°C which must be interpreted as being the result of a eutectic reaction. By extrapolation of the liquidus to this temperature, the eutectic composition was estimated to be about 0.25 at. pct In. The present estimate of the eutectic temperature and composition are in good agreement with the values of 96.0° to 96.2°C and between 0.28 and 0.45 at. pct In, respectively, which were reported by Heycock and Neville.2 However, no further information on the liquidus of this system at the sodium-rich end could be found in the literature for comparison. One compound: NaIn, has been reported in this sys-

Jan 1, 1968

By H. Oda, L. E. Fong, K. K. McBride, B. P. Weiss, F. J. Baudenbacher, A. Usui

Fine-scale dating is a key parameter in characterizing the growth history of hydrogenetic ferromanganese crusts. We once compared several dating methods, micropaleontological (calcareous nanofossil), radiometric (10/9Be), and paleomagnetic (step-wise measured inclination) methods on single samples, but these independent methods were not consistent with each other (Joshima & Usui, 1999). For example, a 4-cm thick crust was dated as 3Ma by the fossil-paleomagnetic combined method, while it dated older than 5.5 Ma by Be-10 dating. This discrepancy suggests a question if the Be-10 radiometric method can give us false ages or growth rates (Usui et al., 2002) because of post-depositional change, diffusion or other reasons. In order to answer the question, we conducted ultra-fine magnetostratigraphy with a SQUID microscope on the same hydrogenetic Mn crust sample. Rock magnetic measurements revealed that the main magnetic mineral is well dispersed single domain grains, which is typical to magnetite but not yet specified (Oda, 2005).

Aug 24, 2006

German manufacturer DBT signed a contract to supply a sixth automated-plow long-wall system to Shenyang Coal in Liaoning province in northeastern China. This most recent order occurred just weeks after DBT signed a contract to deliver a fifth automated-plow longwall system to Datong Coal in Shanxi province. The plow will go into service at Shenyang Coal’s Hongyang Mine. Mining conditions at the mine, coupled with DBT’s advanced automated-plow technology, means that the system has the potential to become one of the world’s most productive thin-seam longwalls.

Jan 1, 2004

By P. R. Warner

This paper reviews the development of certain aspects of the electrical specifications of Anglo American?s suite of specifications for gearless mill drives (?GMDs?). These specifications are based on experiences in both Anglo American?s and others? operations, benchmarking against large hydro generators, the advice of industry and university experts, and continuous close co-operation with OEMs. To achieve a step change in availability additional final testing and electrical protection have been implemented, insulation requirements have been specified for machines to be operated at high altitude and clean area and access control systems have been developed.

Jan 1, 2012

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905