Search Documents

By George D. Roberts

INTRODUCTION CIVIL engineers are primarily interested in maximum core recovery. This is even more important in foundation work than in mining investigations where sludge samples are of some value. The soft materials, such as clay, gouge, or partially decomposed seams that are most readily ground up or washed away, are the materials that usually have the greatest influence on foundation and leakage conditions. Undisturbed samples of such materials should be obtained for detailed geological examination and laboratory tests. Therefore the attainable goal of sampling in connection with foundation investigations is the recovery of 99.9 pct of undisturbed core. FACTORS CAUSING CORE LOSSES The principal factors contributing to core losses are: (I) coring badly fractured or very soft material; (2) use of improperly designed coring equipment, including the use of bits of too small a diameter; (3) lack of the proper training and attitude on the part of the drillers and pertinent technical information on the part of the supervising personnel. Little can be done about the character of the material being cored but the other two factors contributing to unsatisfactory performance can be corrected. Although the title of this paper is the improvement and standardization of core barrels, it is believed that the drillers' shortcomings and the lack of pertinent technical literature are more detrimental to good core recovery than either of the other factors. USES FOR LARGE DIAMETER CORE BARRELS It is well known that the use of larger diameter bits and core barrels generally produce better cores, particularly when sampling soft or broken material. The use of larger and larger bit diameters and the insistence on better core recovery is well demonstrated by the change in practices of the various districts of the Corps of Engineers. Today NX core is the smallest diameter commonly permitted for investigational work and the more active districts are using coring bits up to 6 in. in diameter, as well as 36 and 40-in. calyx rigs. The latter size has proved to be just as economical because it provides more room for core removal and cleanup operations. The use of large diameter cores to replace the driving and jacking methods of obtaining soil samples is also increasing. The 5 7/8-in. Denison sampler, developed by H. L. Johnson to obtain samples from soft formations, is one example. The principal uses for bits larger than NX are: sampling soils and semi-consolidated rock; sampling decomposed rock or rock with soft seams; sampling concrete; obtaining samples for laboratory tests; drilling drainage holes, and other miscellaneous work. CORE DRILLING PRACTICES OF SEVERAL ENGINEER DISTRICTS Little Rock District The writer was employed in the Little Rock District from 1938 until 1942. Prior

Jan 1, 1947

"The National Mining Hall of Fame and Museum (NMHFM) announced the class of 2019 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exceptional financial acumen in assembling several operations that formed the basis of a successful American mining company; conception and development of equipment which contributed to improved efficiency and mine safety; and unrelenting advocacy for the U.S. mining industry and its workers. These individuals, selected for being determined, forward-thinking innovators, doers and leaders have propelled the industry toward vastly improved safety and social responsibility.The Prazen Living Legend of Mining Award, named for renowned mining artist Gary Prazen, will also be presented at the ceremony. This award recognizes an individual or organization for significant and sustained commitment to educating the public about the relationship of mining to our everyday lives through educational materials, programming, and outreach.2019 National Mining Hall of Fame inducteesFrank Calandra, Jr. has devoted more than 50 years to the mining industry and he is an icon in ground control technology for the mining, tunneling and civil construction industries.From the ground up, his passion, sweat equity and shrewd business acumen have grown Frank Calandra, Inc. (FCI) and Jennmar from a single plant in Pennsylvania to a world-class enterprise with 25 plants employing thousands globally. As evidenced by Calandra’s more than 20 patents on ground control devices (not to mention the additional 80 patents his companies hold), his innovation and commitment to safety have made underground mining safer and more efficient. In the late 1970s and early 1980s, Calandra was instrumental in upgrading American Society for Testing and Materials (ASTM) standards in roof control for both state and federal regulations. Through his work with industry associations such as the National Mining Association, National Coal Council and Center for Energy and Economic Development, among others, Calandra has contributed his time, expertise and financial support to ensure a balanced political and regulatory climate for mining. Calandra is an inductee of the West Virginia Coal Hall of Fame."

Aug 1, 2019

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By J. R. Mattern

The engineering geology of the Rio Tinto Borax Boron Mine creates challenges in providing practical slope design recommendations to mine planning engineers. Low strength sedimentary units interbedded with very low strength lakebed clays surround the orebody. Faulting has offset and juxtaposed these units into variably adverse orientations, while groundwater is compartmentalized both vertically and horizontally within fault blocks. A collective program of geologic data collection, geomechanical strength testing, geologic modeling, slope depressurization, confirmation of underground stope locations, and documentation of slope behavior provides vital information for design investigations and sensitivities. Analysis results lead to risk assessments and operational procedures that add value to the business by optimizing slope configurations and minimizing risk.

Jan 1, 2004

By Rodger C. Smith

The topic chat has been assigned to me ?Economic and Political Climate of the Potash Industry? is a function of two basic facts: 1. Potassium is absolutely essential to plant and animal growth. Along with nitrogen and phosphorus it is one of three major plant nutrients, the three nutrients required in largest quantities for plant growth. 2. United States is unequivocally an "have not" nation with regard to potassium. Quantity of potassium ores is limited and, more disturbing, the cost of production at all U.S. potash mines is marginal in comparison with the major producing countries, i.e. Canada and U.S.S.R.

Jan 1, 1983

By Magnus Troilius

The importance of having methods for the rapid and accurate determination of manganese in modern steel manufacture cannot be overestimated. The method adopted in the laboratory of the Midvale Steel Works is very satisfactory, and I think it will be of interest to some of the members to give a description of it. Before giving the more detailed account of the manipulations, a review of some well-known methods and chemical facts may not be out of place. The " bromine and ammonia" process, as fully described in the tenth volume of the Transactions of this Institute, was certainly an improvement on the methods in which fixed alkaline salts were used, as these gave invariably too high resnlts, as generally carried out. But the separation of all the iron before the manganese was, in both methods, a source of great inconvenience and delay.

Jan 1, 1884

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By M. Kane, O&apos

BHP Iron Ore initiated research programs in January of 1995 to develop long term plans for decommissioning of the waste rock material at their Mt. Whaleback operation. More than 2 billion tonnes of waste rock were deposited during the past 30 years. Ultimately, the operators will deposit a total of approximately 5 billion tonnes in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semi-arid climate adjacent to Newman, Western Australia, approximately 1200km north-northeast of Perth, Western Australia. The primary research program includes the development of technology for the long term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion, and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. A laboratory program and the soil-atmosphere modelling completed to design the horizontal field test plots are described. The construction of the horizontal surface field test plots are discussed together with the field instruments installed to monitor performance. The key components of the instrumentation program are the design and installation of large scale field lysimeters to measure the unsaturated flow of moisture into the waste rock from the base of the cover layer. The cover system is designed to maximize infiltration during wet periods for subsequent evapo-transpiration while minimizing surface runoff. The result is a near zero net infiltration to the underlying waste material. A key feature of the design is the use of pit run waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long term performance.

Jan 1, 1998

By J. V. Emmons

IT has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass. Within the last few years it has been generally recognized that many of these properties were clue to surface decarbonization. The origin and effects of this altering of the composition have been but little studied. C. M. Johnson' arrives at the conclusion that, in annealing, "the most active agent in surface decarbonization is the rust or scale (present on the surface), which is actually reduced to metal at the expense of the carbon in the steel to which it adheres." W. H. Hatfield in his admirable paper, The Chemical Physics Involved in the Decarburization of Iron-Carbon Alloys,' has given us the most tenable theory of the removal of carbon from iron. While Mr. Hatfield's work has been principally clone in connection with the annealing of white cast iron to produce malleable castings, it is frequently applicable to the decarbonization of tool steel. The following equations which he proposed have been fully borne out by the author's experiments: 2Fe3C + 2CO2 = 3Fe2 + 4C0 2C0 + 02 = 2C02 Continuous 2C02 + 2Fe3C = 3Fe2 + 4C0 It is the purpose of the author to show, in a quantitative manner, the effect of various treatments in eliminating the carbon in tool steel. Some of the phenomena of the decarbonized surface will also be described, as well as the practical problems they present to. the manufacturer and user of tool-steel products.

Jan 9, 1914

By Robert R. Walden, LeMont West

K ENTUCKY'S first acid-grade fluorspar flotation Kmill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant. The Mexico flotation plant was reconditioned and designed to produce acid-grade fluorspar from the jig tailing stockpile. The new plant flowsheet is shown in Fig. 2. The ore feed, old tailing, which contains 10 pct of waste rock and coarse gravel assaying approximately 8 pct CaF,, is bound together by sticky clay

Jan 1, 1955

By L. G. Austin

The data of Dunn and Martin (1978) is reanalyzed using a rigorous application of Hertzian theory to the impact process. The Young's modulus of steel required to fit their data to the theory is a factor of about 10 3, too low compared to the values quoted for steels. Thus, doubt is thrown on the validity of their experimental technique, and it is possible that their values for maximum impact force and stress are far too low.

Jan 1, 2002

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By R. W. Raymond

The tidings of Mr. Hewitt's death, cabled to me at Rome, Italy, brought me a great shock as well as a sincere sorrow. I had left him, a few weeks before, not indeed in vigorous health, but still quite able to command recognition as a continued power in public affairs; and I thought him destined to enjoy for many years that final stage of a long, active and honored career, in which, having passed beyond the struggles and rivalries of business and of politics, his life and character could be justly appreciated by all men, like some noble work of art, already crowned, and marked henceforward "hors de concours." Moreover, he was, and would be to the end, not merely the passive recipient of admiration and esteem, but the source of iuspiring appeals, effective warnings and wise counsel. His rich and varied experience he had placed at the service of his fellows. His lightest word was weighty, and those who contradiEted him only injured their own cause thereby. Great trusts (true " trusts," in the old and proper sense of the term), like the Cooper Union, the Carnegie Institution, and others, still commanded his disinterested services. Great principles of liberty and of justice continued to be reinforced in perilous crises by his powerful advocacy; great measures were daily receiving from him a decisive impetus. No wonder it seemed to. us that this happy period of reward so well earned, and of beneacence so welcome to innumerable recipients of its blessing, must continue yet awhile. We did not expect the night instailtly to engulf the full-orbed sun. Nor, indeed, has this been our experience; in this instance, the sunset has left an afterglow more luminous than many a noonday. For the principal data contained in the following brief sketch of Mr. Hewitt's life, I rely upon memoranda personally approved by hirn, some months before his death, for my use in

Jan 1, 1904

By L. G. Laureau

This paper is presented to call the attention of steel-manufacturers to the need of further reform in the manner of casting and handling ingots. The problem of making the work usually performed in and around the casting-pit less dangerous to the men and less costly to the management is one which has occupied the minds

Jan 1, 1885

By P. S. Miller, S. H. Ash

Extensive and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past I0 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the Succdeding face, constituting a round. Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons" tunne1ing is more hazardous than mining in any branch of the mineral industry. On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. The Delaware Aqueduct The new Delaware aqueduct is a Manhattan project of some magnitude; when regular it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1943

By Samuel H. Dolbear

THE value of a mine is basically dependent on its capacity to yield profits. Since the ore must be mined, treated, and sold, some of it in various future years. there is a risk involved as to future costs, selling price, and working conditions. It cannot be expected that the economic condition existing at the time of valuation will continue unchanged for long periods in the future. During the past 20 years, mineral production in the United States has been conducted under a changing economy in many respects more exacting than that applied to other businesses. There have been increased production incentives, technical aid, exploration of privately owned mineral deposits by government at federal expense, and liberal loans for development and equipment, with risk partially assumed by government.. Some of these benefits have been counterbalanced by price ceilings, consumption controls, and stimulation of competition from foreign producers who have been offered the same advantages extended to American operators. For the present, mines will operate under a government policy directed toward reducing federal aid and control. The tenure of this change will depend upon future elections and the status of foreign relations. War and threat of war are now of the most vital significance to the mineral industries. Other factors which influence cost of production, markets, and price of mine output might be classified as Acts of God or Acts of Government. In some countries expropriation and the difficulty of exporting earnings or investment returns are risks that must be considered by foreign capital. Recognizing that this retards American investment in foreign countries, the Mutual Security Agency offers insurance against such expropriation and guarantees the convertibility of capital and profits. Since it is impossible to predict with certainty either cost of production or selling prices of metals for long periods, some assumptions must be made as to profits in the future. The basic assumption must be that the price of the company's product will vary in proportion to changes in operating cost. There is often a lag in this reaction, however, for prices of minerals are generally more sensitive to declines and less sensitive to increases than are costs. This reflects in part the resistance of labor to downward wage revision and a corresponding alertness in realizing its share of price advances. Some labor contracts include automatic adjustments to metal prices. Notwithstanding the complexity of the, problems involved and the difficulty of weighing their effect on value, such risks may be appraised with reasonable accuracy and a rate of earnings adopted that is compatible with the risk. It is, of course, possible to revert to a yardstick of value such as the commodity dollar, which has been advocated from time to time, but while revaluation in 1933 disturbed public confidence, the theoretical gold dollar continues to be the standard of greatest stability. Its gain or loss in purchasing power is reflected ultimately in cost of production and selling price of the mine product. At present 35 dollars are allocated to one ounce of gold. Measurement of Risk In the application of the Hoskold and most other formulae, a yearly dividend rate commensurate with the risk involved is set aside out of annual earnings. If the risk is great, this rate may be 15 to 25 pct of the amount invested. The remainder is placed in a sinking fund invested in safe securities such as high grade bonds or conservative equities, and the interest or dividends from these securities are added to the sinking fund. The sum of these sinking fund payments and the compounded interest at the end of the mine life is taken as the value of the mine. Admittedly the decision as to the size of the risk rate is the most difficult element in valuation and one requiring the most exacting consideration. It is necessary to look years ahead in an effort to determine future costs, market prices, demand, competition which may develop, including that of substitutes, and other influences common to the mine and to the region in which it is situated. Another phase of risk is the enactment of unfavorable legislation, taxes, and what appears to be an alarming spread of nationalization and expropriation. Capital is sometimes borrowed from the government to finance strategic production. Such loans may be collectable only out of production and involve no liability otherwise. Valuation in these cases must recognize the effect of such a reduction in liability. Offsetting some of these risks are the possibilities of mechanization and other cost-reducing discoveries, improvements in mining and treatment methods, new uses for minerals and metals, and normal growth of markets. In this paper, the terms risk rate, dividend rate, and speculative rate are synonymous. Safe rate and redemption rate are also used interchangeably. These alternatives are used here because they are commonly found in the literature on mine valuation. In Michigan, the State Tax Commission has long employed a risk rate of 6 pct in its valuation of iron mines. There the outline of reserves is well established and operating costs and conditions are based on adequate experience. The following comment on rates appears in the report of the Minnesota Interior commission on Iron Ore Taxation submitted to the Minnesota Legislature of 1941.1 Most engineers agree that 7 percent for the specu-lative rate is "an absolute minimum". C. K. Leith in

Jan 1, 1954

By T. K. McCranie, A. H. Tousley, A. H. Kackman, L. R. Gregory, A. Jr. McElrath, R. J. Krekel

In Roman and earlier civilizations the term cement was applied only to mixtures of lime, pozzolana, sand, water, etc., used as a mortar to bind larger stones. Today, portland cement, the subject of this section, can be briefly defined as follows: The product obtained by finely grinding clinker produced by calcining to incipient fusion (i.e., sintering) an intimate and properly proportioned mixture of argillaceous and calcareous materials. History The Egyptians were probably the first to join building stones with a mixture of sand and a cementitious material (i.e., having the property of or acting like cement). It is generally accepted that the cement used by the Egyptians on such structures as the Great Pyramid was calcined gypsum, Later the Greeks began to calcine limestone for use as a mortar with sand and water. Still later, broken brick and tile were added to the mortar to make the first concrete. The Greeks and Romans found that some sands produced mortars that were especially resistant to the action of water. Hydraulic (i.e., underwater-hardening) cements formed by combining slaked lime, water, and finely divided siliceous materials (e.g., pozzolana) possess superior strength and are capable of resisting the destructive action of water. They were used on the Pantheon, Colosseum, and other structures, some of which are still standing. In 1756 an English engineer, John Smeaton, found that an argillaceous limestone (i.e., containing an appreciable amount of clay as an impurity) produced a cement with greater resistance to the action of water. Despite Smeaton's findings, the use of the old mixture of lime and pozzolana long retained its popularity. Significant contributions in cement technology from England, Swe¬den, France, and Holland were made in the next 68 years. However, the invention of portland cement is generally credited to Joseph Aspdin, an Englishman, who in 1824 patented "portland cement." The name was selected because, on hardening, it resembled the natural building stone from the Isle of Portland, England. The patent features mixing ground limestone and argillaceous materials in appropriate proportions and calcining (i.e., expelling CO2 by roasting) the mixture. This superseded the existing practice of calcining naturally occurring argillaceous limestone. In about 1845 Isaac Johnson, also English, conducted experiments on proportioning the components and calcining them at higher tem¬peratures. His accomplishments are accepted as the beginning of the present-day portland cement industry. The U.S. cement industry originated with the demand for good hydraulic cement for building structures such as the Erie Canal, which was started in 1817. The first discovery of cement rock (i.e., naturally occurring argillaceous limestone with near-optimum ratios of calcium carbonate, alumina, and silica) near Fayetteville, N.Y., was made by C. White. In 1818, White secured a patent for the manufacture of natural cement from that deposit. Subsequently, several natural cement plants were built in 1830-1840 at Rosendale, N.Y., and in the Lehigh Valley of Pennsylvania. David Saylor, who participated in establishing a natural cement plant at Coplay, Pa., in 1850 discovered that a superior cement could be produced by calcining the rock at higher temperatures than hith¬erto. In 1871, Saylor obtained a patent and commenced the manufac¬ture of portland cement. By 1890, there were 17 portland cement plants in the United States with a combined annual output of 62,300 tons. At the end of 1970, the number of plants producing portland cement in the United States (including Puerto Rico) was 169, down from a maximum of 185 in 1967, with total annual shipments of 73.4 million tons valued at $1,298 million. (Fig. 1). In 1970, annual world production of hydraulic cement (which includes pozzolanic materials, hydraulic limes, natural cement, alumina cement, and portland cement, all of which are in current use in various parts of the world) reached 630 million tons (Table 1). Flowsheets of typical U.S. cement plants are shown in Chapter 13. Chemical Composition and Physical Properties It is generally accepted that portland cement clinker consists of a mixture of compounds or synthetic minerals. The four principal compounds are:

Jan 1, 1985

By L. A. Morley, W. T. Parry

Engineering design problems encountered by mining engineers often depend on the properties of natural granular materials such as soil, poorly consolidated sediment, fault gouge, and hydrothermally produced clay. The physical properties of such granular materials frequently are determined by the properties of silicate clays. In most mining applications, the clays are in contact with water. Swelling of clay due to water infiltration can interfere with underground support and haulage systems. Water-saturated clay on fault, fracture, and bedding planes causes slope failures in open pit mines, roof falls and heaving of weak underclays in coal mines. Water may be removed and cementing agents may be produced in clays by electrical methods. When an electrical potential gradient is applied to a charged capillary by two electrodes, water moves toward the negative electrode.1 This electrokinetic phenomena is known as electroosmosis and has been used to successfully dewater clay minerals which lack strength because of water. A consolidation effect occurs when the flow of water is accompanied by a decrease in water content. Electrochemical changes in the clay result in cementing and irreversible hardening. Theory A mathematical basis of electroosmotic phenomena is presented by Helmholtz.3 Smoluchowski5 modifies Helmholtz’ model and presents Eq. 1 to describe fluid flow velocity due to electroosmosis. For this formula, the zeta potential can be measured experimentally. The Helmholtz-Smoluchowski model is reasonably valid for clay aggregates with large pores saturated with fresh water or dilute electrolyte solutions.° An assumption used for Eq. 1 (equations are given Table 1; terms are defined in Table 2) is that the thickness of the electrical double layer surrounding the clay particles is small compared with the pore radii. Because this is generally not the case, Schmid7 presents Eq. 2. The volume charge density in the pore may be approximated from cation exchange capacity and porosity measurements. Casagrande8 offers a semi-empirical relationship (Eq. 3) for volume rate of electroosmotic flow and finds that k, is relatively constant for most clays with an average

Jan 1, 1972

By P. Gray

Process and engineering development of the Warner Zinc Process over the past two decades has proceeded alongside the world-wide collection and analysis of operating and cost data of current processing practices from sulphide ores to refined metals. Study of these data shows that recoveries are dependent on mineralogical characteristics of the sulphide matrix and point to the inadequacy of differential flotation as a tool for preparing feed for smelters. The paid-for return at the mine on the combined metal values in zinc rich sulphide ores rarely exceeds 80% and increasingly runs as low as 50-60%. Surveying the possible alternative ways of improving these performances leads to the conclusion that the Warner Process is the only technology in sight that could meet a target of 90% paid-for recovery and that its development has now reached a point where it can be a fully practicable process for all mixed sulphide ores.

Jan 1, 2000

Not quite a year ago, during a speech to a group of mining professionals in Washington, DC, the subject centered around the long-range importance of conducting research projects and how much that research needs to specifically apply to health and safety matters in our industry. The point was made about the critical need to work together with government, private industry, labor organizations and academia speaking with a unified voice as we all march into the future together. The fundamental benefits of competitive research were mentioned --to improve our quality of life, to develop our energy resources, to achieve a safe and healthy environment and to ensure long-term economic growth. Very importantly, emphasis was given to the natural link that makes my agency, the Mine Safety and Health Administration, and the National Institute for Occupational Safety and Health --NIOSH --the beneficiaries of each other's findings. Unquestionably, there are lines of separation. The main responsibility of the agency I represent, MSHA, is enforcement of the nation's mine safety and health laws. But we also have an additional responsibility and that is to coordinate and give priority to research in a never-ending hunt for answers.

Jan 1, 1999