Search Documents

By Jian Li, J. Miles, P. Liu, W. Cook, W. Zheng, Alvin Qian

"High temperature corrosion resistance is one of the key challenges in water-cooled nuclear reactor material development. Iron based materials with low Cr content exhibits superior high temperature mechanical properties. However, due to the relatively low Cr content, their corrosion resistances under supercritical water (SCW) conditions are generally poor. High-Cr alloys, despite their much improved corrosion resistance, often suffer from embitterment due to the precipitation of sigma phase in the microstructure. In this study, corrosion resistance of an in-house produced high Cr steel (25%Cr) showed much better corrosion resistance compared to that of low Cr alloy (14%Cr). This high-Cr steel can potentially be used as a corrosion-resistant coating for structural materials in sew applications.INTRODUCTIONThe supercritical water-cooled reactor (SCWR) concept is one of the promising designs for the next generation nuclear reactor, in which the water coolant is designed to be at about 625°C and 25 MPa at the outlet of the reactor core. Under these relatively high-temperature and high-pressure conditions, the cooling water is at supercritical state. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR in-core conditions. Canada supports research in several key areas of SCWR development, including materials selection. A major focus is on materials development, selection and evaluation for both in-core and out-of-core components.Allen et. al. [1] carried out a comprehensive study on the SCW corrosion resistance up to 600 °C on commercially available high temperature materials including Ni-based super alloys, various types of stainless steels and ferritic/matensitic steels. They concluded that ferritic steels develop a relatively thick but mechanically stable oxide layer, while austenitic alloys develop a thinner oxide layer that has been found to spall in some cases. Of the three types of alloys examined, the Ni-based alloys exhibited the lowest oxide thickness, however pitting was observed in the vicinity of intermetallic precipitates."

Jan 1, 2011

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By Terje Preber

Undisturbed sampling of shale has always been difficult. As pert of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois, the Maquoketa shale, which contains seams of argillaceous dolomite, was sampled using different coring techniques. Since the Maquoketa shale is extremely fissile, careful sampling preservation by both lateral and vertical confining was utilized. The samples were tested to determine both static and dynamic properties. A relationship between void ratio and compression index, swell index, and swell pressure ratio was established. Correlation was found between the dynamic properties and both undrained shear strength and confining stress. Based on the results of the sampling and testing programs, recommendations for sampling and sample preservation techniques are given. INTRODUCTION Undisturbed sampling and preservation of samples of weathered, fiasile shale is often a very difficult task. The often erratically varying degree of weathering with depth complicates sampling and makes reproducibility of testing results difficult. Therefore, the testing of weak, weathered rock very often yields a wide variety of test results with large data scatter. The reproducibility of teat results usually associated with water-deposited soils is seldom, if ever, obtained. The testing and sampling program described in this paper was part of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois. The sampling, preservation and testing program of shale samples taken from the Maquoketa shale are described, and, in particular, the different sampling techniques and sample preservation procedures are evaluated with respect to their effectiveness. The samples obtained by these procedures were subjected to a comprehensive testing program, including both static and dynamic testing in order to provide input for soil-structure interaction analysis. GEOLOGY The Maquoketa Shale Group is of Ordovician age and is part of the Cincinnatian Series. The area where the shale samples were taken was in a broad sea far from sources of clastic sediments during most of Ordovician time. However, during Cincinnatian time when large deltas in the Appalachian region were being formed, clastic sediments from the east dominated the sedimentation ii. Illinois, resulting in formation of the shale and dolomite shales of the Maquoketa Shale Group (Willman et al., 1975). The geologic unit sampled consists of a greenish gray to gray silty shale containing numerous 1- to 12-inch (2.5- to 30.5-cm) thick interbeds of argillaceous dolomite. The dolomite comprises up to 40 percent of the profile studied. The shale

Jan 1, 1984

By Juan Ayza

Ante el peligro de la concentración y exposición de los polvos de sílices en el personal minero, el presente texto revisa la silicosis -en tanto determina las propiedades de los polvos en reacción y su relación con los medios para detectarlo. Asimismo este estudio constituye en un problema de mecánica de fluidos, donde las operaciones más peligrosas se evidencian en la perforación y explosiones. También se refieren algunos datos sobre los costos de profilaxis de la silicosis y de las indemnizaciones de los enfermos.

Oct 1, 1955

By D. Beneteau, L. Feldman, D. Milne, A. Hyett, G. Snell

"Behaviour of rebar bolts subjected to combined shear and bending in underground potash mining applications is not well understood. An experimental investigation compared load applied to resin-grouted No. 25 metric rebar to theoretical load, calculated using elastic bending theory. Distributed optical sensing (fibre optic) technology allowed axial strain measurements at 1.25 mm increments along the length of rebar. Experimental procedure, data processing methods, and equipment improvements are needed for field applications of optical sensing technology. Goals were to adopt procedures for instrumenting rebar bolts, conduct tests, and develop data interpretation methods to measure field deformations and loads. ¦ KEYWORDS Fibre optic, Potash mine, Rebar bolts, Transverse load testing RÉSUMÉ On appréhende encore mal le comportement des boulons d’ancrage pour barres d’armature soumis au cisaillement et au cintrage pour un usage dans des mines de potasse souterraines. Une étude expérimentale compare la charge appliquée aux barres d’armature de diamètre n° 25 (25 mm en mesure métrique) enduites de résine époxy à la charge théorique, calculée à l’aide de la théorie de la flexion élastique. La technologie de détection optique distribuée (fibre optique) a permis d’effectuer des mesures de la contrainte axiale à des différentielles de 1,25 mm sur toute la longueur de la barre d’armature. Pour des applications sur le terrain de la technologie de détection optique, il faut envisager une procédure expérimentale, des méthodes de traitement de données et une amélioration de l’équipement. Les objectifs établis consistent à adopter des procédures d’instrumentation des boulons d’ancrage pour barres d’armature, à effectuer des essais et à mettre au point des méthodes d’interprétation des données pour mesurer les déformations et les charges sur le site. ¦ MOTS CLÉS boulons d’ancrage pour barres d’armature, essai par charge transversale, fibre optique, mine de potasseINTRODUCTION Resin grouted rebar bolts are commonly used in potash mines in the province of Saskatchewan, Canada, in areas where shear deformation is observed in the rock, or where potentially unstable ground is present, including locations such as clay seams. Opportunities to observe deformations of rebar, as shown in Figure 1, are rare because it is unusual in underground potash mining to excavate supported ground. In this situation, a block of potash containing a rebar bolt had failed."

Jan 1, 2019

By I. K. Gilmore

PCS Phosphate operates an open-pit phosphate mine in the central coastal plane of North Carolina. The company has mining and refining facilities located on the south shore of the Pamlico River. Phosphate ore is recovered at the Aurora facility by open-cast mining techniques. Walking draglines and bucketwheel excavators remove the overburden and mine the phosphate ore. The mined ore is slurried about 8 km (5 miles) to the processing plant. At the plant, the phosphate ore slurry is passed through screens to remove material coarser than 2 mm (10 mesh) and then pumped through hydrocyclones to remove material finer than 75 mm (200 mesh). The resulting phosphate and sand mixture is treated with various reagents and subjected to an anionic flotation process. A cationic flotation process removes the sand from the final phosphate concentrate.

Jan 1, 1995

"INTRODUCTION Secondary mine ventilation has been hamstrung by the availability of fans that satisfy many competing operational factors. The sometimes legislated requirement of adequate volume to the working face, the minimisation of excavation required to fit the selected secondary fan and the power requirements of various operational phases has, in the past, not been satisfied with just one system. The new system being introduced overcomes all these competing requirements in one simple unit with an added bonus of being very durable without loss of performance when wear occurs on the impeller. Existing Operational Situation Several studies (e.g., CIPEC, 2005; LCG Energy Management Group, 2009) have found that between 42% and 49% of mining energy costs are associated with mine ventilation, depending on the type of mine and the equipment used. If we then look at the general breakdown of installed power of the secondary fan to primary vent fans, the ratio is around 2:1. Thus the total energy costs of the secondary ventilation represents about 25% of the overall mining energy costs. It is of interest to note that the cost of running a typical two stage axial vs the cost of purchasing and general maintenance cost of the same fan over a 10 year period, the breakdown will be conservatively in the order of 40:1.The currently available secondary ventilation axial fan have one duty curve at any given time. Generally this can be changed manually within the motor power parameters but requires a minor outage and removal of the fan to do the pitch adjustments. As the bag vent ducts grow longer, the supplied air reduces to a point where inadequate air is supplied to the working face. This is exacerbated by underground equipment putting additional resistance in the heading and further reducing the supplied air at the working face. This shortfall is normally corrected by the installation of an additional fan in the system to overcome losses in the bag system but comes at a cost of production as the heading needs to be shutdown to install the second fan. This also means that the heading is supplied with excessive air on the shorter runs with a wastage of fan power."

Jan 1, 2019

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By W. L. Parker, W. A. Selvig

"Introduction.Powdered or pulverized coal is extensively used as a fuel, the total annual consumption*** in the United States being about 12.000,000 tons, and growing steadily. As the coal is usually pulverized so that 70 per cent or more parses through a 200-mesh sieve, it presents difficulties in sieving, because such finely divided material tends to clog the meshes. A fineness test is desirable in order to judge the efficiency of the pulverizing apparatus, and as an indication of the particle size of the coal being burned.Committee D-5 on Coal and Coke, American Society for Testing Materials, has recognized the desirability' of a standard method for determination of fineness of powdered coal. The Bureau of Mines, in co-operation with this Committee, conducted sieving tests on two standard samples of powdered coal, which are described in this paper. As a result of this work a method for making fineness tests, by band sieving, is recommended as a standard method, while a rapid method, by machine sieving, is given for routine tests.Outline of Investigation.Preliminary trial tests were made by the bureau and tentative methods were formulated for making the sieving tests both by band and by machine.Each of two samples of powdered coal was carefully mixed, and portions were sent to the twelve laboratories mentioned later. These were requested to make duplicate sieving tests on the two standard samples, by the hand-sieving and machine-sieving methods, and to follow the tentative procedure exactly as outlined. All of the laboratories made sieving tests by hand shaking and eight of them made tests by machine shaking."

Nov 1, 1923

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions prevail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes. CLASSIFICATION OF MOISTURE Moisture in coal can be classified as inherent and surface moisture. Inherent moisture is regarded as a part of the true coal substance, having been present in the original vegetal matter from which coal was

Jan 1, 1943

J. S. UNGER,* Pittsburg, Pa, . (written discussion?).-The author of the paper has given an excellent description of the appliances used to cool parts of an open-hearth furnace, and some of the reasons why the refractories fail in service. Personally, I favor water-cooling, but to a limited degree. At one time I advocated more universal cooling than is now practised, but believe I must change my mind. Water-cooled, thin-lined blast furnaces have not proved as satisfactory as anticipated. While this may retard the building of many such furnaces, it will not prevent the use of regular tuyere- and bosh-cooling appliances. Water-cooling any furnace may be easily carried to the extreme. In an open-hearth furnace, excessive port or roof cooling, or cooling the working floors may preserve the lines of the furnace, lower the cost of refractories, acid to the comfort of the workmen, and necessitate fewer shutdowns for repairs, but it may not be good economy on account of the high first cost, the cost of cooling water, maintenance of cooling appliances, and the immediate reflection in a higher fuel cost. The question becomes a financial one, and is answered by using water-cooling devices up to the point at which they cease to show true economies. Open-hearth furnace bulkheads, roofs, and ports fail rapidly in about the order named. If they could be made to last indefinitely by water-cooling, the furnace would still have to be shut clown periodically for cleaning the slag pockets, regenerator chambers, and flues. Extra, or spare, pockets and regenerator chambers have been advocated to permit of continuous operation, but the space required, the cost of installation, and the fuel required to initially heat such cold chambers will largely prevent their adoption. Some particular fuels, as high-ash powdered coal, require frequent stoppages for cleaning, but for this particular fuel a special provision can' be made.

Jan 5, 1919

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

By M. L. Joy

The heat pipe is a self-contained, passive structure that uses a liquid-vapour fluid cycle to provide high thermal conductance . Through the proper selection of working fluids and container materials, heat pipes have been operated at temperatures ranging from less than -300°F to more than 3,000 °F. The passive nature, high efficiency and configuration flexibility of the heat pipe are presented. The application of McDonnell Douglas Astronautics Company Cryo-Anchor® heat pipes for foundation and support stabilization in permafrost regions is discussed. Using the proven Cryo-Anchor technology base. a proposed application of heat pipes in a cold -region mine ventilation system heat recovery heat exchanger is presented. Information obtained from the development of an air-cooled heat pipe steam condenser provides the technical basis for large -scale heat pipe applications.

Jan 1, 1978

By Brian E. Travis

The recent development of polymer grids for the underground coal mining industry has created new alternatives for supplemental ground control practices. The grids utilize strong, lightweight polymers - usually special grades of polypropylene. High tensile strengths and resulting load support characteristics are achieved by molecular orientation of these polymers in the manufacturing process. One of the most important applications of polymer grids as supplemental ground control is in longwall shield recovery. When shields are moved from one face to another, the determining factor in the success of the recovery is the ground control provided by roof support structures along the old face. Whereas primary support is usually provided by roof bolts and cables which run the full width of the panel, supplemental support is often provided by metallic meshes of welded wire or chain-link fence. lightweight, high-strength polymer grids replace these heavy, cumbersome metallic meshes, giving the operation increased productivity by decreasing installation time and reducing injury downtime.

Jan 1, 1990

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By Walter J. Karplus

By means of a finite difference expansion a fluid flow field in cylindrical coordinates with axial symmetry, is simulated by a network of electrical resistors. A series of DC analog computing units, connected to the network bounrlary corresponding to the free surface effectively adjust the network parameterr to satisfy simultaneously Laplace's equation and the borrndary conditions. The system automatica1ly "re1axes" to the correct boundary shape in a fraction of a second. A detailed application of the method to the water coning problem in oil wells is presented. INTRODUCTION The water coning problem in petroleum production is a prime example of a class of problems known as free surface problems. A free surface arises in fluid flow regions when the shape of the boundary of a single phase flow region is affected in some manner by the pressure or potential gradients within the region. When there exists an interface of two fluids of different densities, the shape of this interface will be determined by the relative velocities of the two fluids and will therefore comprise a free surface. Other free surface problems of interest to petroleum engineers include the gas coning, water injection, and gravity drainage probIcms. In each case it is desired to predict the shape of the boundary of the oil zone as a function of the flow rate, the well penetration and the physical parameters and dimensions of the system. Such problems do not lend themselves to the classical analytical treatments of boundary value problems because in this case the boundary of the potential field and the potential distribution within the field are interdependent and must be calculated simultaneously. A further difficulty arises from geometric considerations. Since the fluid flow is of the radial type in most cases, such effective methods as conformal transformation and the hodograph are not applicable. It is the purpose of this paper to present a method whereby free surface problems of this type may be solved rapidly to the desired order of accuracy by means of a combination of a network of electrical resistors and conventional analog computer units. The water coning problem is treated in some detail. Then the procedure for extending the technique to other free surface problems is indicated. FORMULATION Most commercial oil reservoirs consist of an oil-saturated sand, bounded above by an impermeable strata and below by a water-saturated sand. Gravimetric separation results in a horizontal oil-water interface. When an oil well is drilled so that it partially penetrates the oil zone, and production is initiated at a constant rate, the oil-water interface will assume a new shape as a result of the pressure gradients in the oil zone. It should be emphasized that this is a steady phenomenon. After an initial transient period the water phase will be completely static and only the oil will be in motion. The new steady-state shape of the interface, as shown in Fig. 1, depends upon the depth of penetration, d, the thickness of the oil zone, I, the production rate, q, the hydraulic permeability zone of the sand, k, the viscosity of the oil, µ, and the densities of the oil and water, p.,. and pw.. The problem is to determine this relationship. Darcy's law + = - (P f g p z).....(1) it.

Jan 1, 1957

By J. G. Tilton

While most of the Pittsburgh coal horizon is dependably regular, there are areas where it is dis-turbed by sandstone cutouts which can seriously hamper mining operations. Because these channel sandstones often cut out the coal abruptly, they are difficult to detect by core drilling; and mine operators, for want of a better way to discover them, have largely trusted to luck to avoid them. This paper, based on a study the author is presently conducting, is an attempt to point out some sources of information and signposts which might aid the operator in determining the presence of a cutout before he begins to mine. The presence of sandstone cutouts in the Pittsburgh coal has been known for many years. Some of these irregularities were observed at outcrops and others were discovered by drilling, but the majority were and are found during mining operations. These sandstone cutouts are commonly called "faults" and have been a bane to mining companies wherever they have been encountered. Profiles of some typical deposits appear in Fig. 1. The cutouts disrupt the normal system of mining, replace valuable coal reserves, create ventilation problems by emitting large quantities of gas and sometimes oil, limit the number of entries that can be economically driven, affect the quality of the coal, disrupt the normal structure of the coal, and create roof control problems. It might be expected that such severe disturbances in the structural regularity of the coal would instigate determined and extensive searches for possible cutouts prior to mining operations, but this apparently has not been so except in isolated cases. Two reasons may be cited to explain this lack of exploratory work. The first and probably the strongest reason is the over-all regularity of the Pittsburgh coal. No coal seam in the country exhibits the horizontal continuity and relative regularity of the Pittsburgh coal. It lies in an almost unbroken sheet across southwestern Pennsylvania, eastern Ohio and northern West Virginia, and has been recognized as far east as the Potomac Basin of western Maryland. Over 5729 square miles are underlain by this coal, of which 2077 square miles are in Pennsylvania, 2214 square miles in West Virginia, 1410 square miles in Ohio, and 28 square miles in Maryland. The area covered by this study is outlined by the map in Fig. 2. Over most of this territory the coal has the following characteristic structure as illustrated in Fig. 3: roof coal, draw slate, breast coal, parting, bearing in coal, parting, brick coal, parting, and bottom coal. With such regularity of thickness and structure, mines were opened and laid out with confidence that the coal would be present. Extensive drill testing was considered unwarranted and it was also quite expensive because the coal dipped to the west away from the Monongahela River. Consequently, drill holes were widely spaced and rarely encountered ad-

Jan 1, 1968

By Elliott A, Kingsnorth D. J

The development of a large high grade spodumene orebody, in excess of 30M tonnes containing at least 7M tonnes at 4.0% Li20, by Lithium Australia Ltd at Greenbushes, Western Australia is significantly increasing the world consumption of lithium minerals. The availability of two low cost sources of lithium, spodumene concentrates (7.5% Li20) and glass grade spodumene (4.8% Li20) has been welcomed by the ceramic and glass industries as it assists them to lower their raw material costs at a time when they are facing severe competition from alternative materials. While there is no shortage of lithium reserves in the world, there has been a shortage of high quality lithium minerals. The Lithium Australia development has filled this need. The favourable factors of high grade, low impurities, open cut mining and existing infrastructure make this an ideal low cost source for a long term downstream lithium industry. The Lithium Australia mine development has filled the need for a reliable long term supply of lithium minerals. The long term viability of this resource is ensured by the unique combination of the following key attributes of the development : High grade reserves of 7.OM tonnes of 4.0% Li20 within 130 metres of the surface, contained within a total proven reserve of 30M tonnes of 2.8 % Li20. Open pit mining with stripping ratio of less than 2.5:1 waste:ore. Low impurities levels, particularly in those elements, that have a detrimental effect on the colour of glass/ceramics i.e. iron, manganese, titanium and chromium. An existing mine infrastructure that includes an adequate water supply for all foreseeable processing requirements. A sophisticated spodumene concentrator utilizing statistical process control to produce a consistently high grade product with minimal impurities. A technically qualified stable workforce fully acquainted with spodumene processing techniques. Greenbushes high grade concentrates have found ready acceptance in the specialty ceramic and glass industries during the past four years. The consistency and high grade/low impurity level of the product has enabled its use in the production of television tubes, oven to table ware, glass fibres, specialty glasses and ceramic glazes.

Jan 1, 1989