Search Documents

By Beatriz Ribeiro Nogueira, Vijaya Kumar Rangari, Esperidiana A. B. Moura, Anne Chinellat, Arifa Parveen, Angel Visentim Ortiz

"Composite consisting of ethylene vinyl alcohol (EVOH) with short piassava fibers were prepared by extrusion process and their thermal and morphological behavior were investigated. The EVOH reinforced with 5 and 10 % of pi as sa va (Attaleafunifera Mart) fiber particle, based on the percentage weight ratio (wt %), untreated and treated with a commercial silane coupling agent, were prepared and the influence of fiber loading and the effect of chemical treatment on their thermal and morphological behavior were evaluated by SEM, DSC and TG analyses. Melt flow index (MFI) of the composites have been determined to evaluate the effects of fiber reinforcement on dynamic viscoelastic melt of the EVOH. In addition, piassava fibers characterization by SEM, FTIR, and organic and inorganic composition have also been carried out. The SEM results of the composites showed surface micrographs without microvoids and a good distribution, dispersion and compatibility between the fillers and the EVOH matrix. Concerning the piassava fibers characterization, the results showed that piassava has higher lignin content than cellulose and hemicelluloses, and around 0.7 % of ash with 52 % of silica (Si02). This high concentration of silica is consistent with the SEM analysis of the fiber that showed a large amount of ""silica rings"" encrusted on their surface.IntroductionLately, great worldwide interest has arisen in developing new technologies that enable the use of products with less environmental impact. Effort has been put into seeking natural modifier applications, particularly regarding the use of natural fibers. Special attention has been given to the use of natural vegetable fibers, because of the huge variety of species available. Such vegetable fibers are usually referred to as lignocellulosic materials [1]. This work evaluated the effects of piassava (Attalea funifera Mart.) fiber incorporation in an ethylene and vinyl alcohol copolymer (EVOH). The EVOH belongs to a family of copolymers with excellent gas barrier properties and resistance to organic compounds, which allow its application in different segments, from food packaging to gas tanks. However, EVOH is very sensitive to moisture, and in conditions of high humidity its gas barrier properties, thermal and mechanical properties are affected."

Jan 1, 2012

By William E. Ford, Edward Salisbury Dana

296. Definition of Specific Gravity. - The specific gravity of a mineral is the ratio of its density * to that of water at 4' C. (39'2' F.). This relative density may be learned in any case by comparing the ratio of the weight of a certain volume of the given substance to that of an equal volume of water; hence the specific gravity is often defined as: the weight of the body divided by the weight of an equal volume of water. The statement that the specific gravity of graphite is 2, of corundum 4, of galena 7-5, etc., means that the densities of the minerals named are 2; 4, and 7'5, etc., times that of water; in other words, as familiarly expressed, any volume of them, a cubic inch for example, weighs 2 times, 4 times, 7.5 times, etc., as much rn a like volume, a cubic inch, of water. Strictly speaking, since the density of water varies with its expansion or contraction under change of temperature, the comparison should be made with water at a fixed temperature, namely 4' C. (39'2' F.), at which it has its maxi- mum density. If made at a higher temperature, a suitable correction should be introduced by calculation. Practically, however, since a high degree of accuracy is not often called for, and, indeed, in many cases is impracticable to attain in consequence of the nature of the material at hand, in the ordinary work of obtaining the specific gravity of minerals the temperature at which the observation is made can safely be neglected. Common variations of temperature would seldom affect the value of the specific gravity to the extent of one unit in the third decimal place.

Jan 1, 1922

By A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics.

Jan 9, 1951

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006

By K. Price, G. Wang, L. R. Moore, Y. R. Xiong, J. Gu

"Sand is a naturally occurring granular material that is a result of the physical or chemical breakdown of rocks. Raw/natural sand contains various minerals, and it is this combination of minerals that brings the value to the construction aggregate industry. However, it is the quartz component of sand that is valued in its application as industrial silica in glass, high purity quartz, foundry sand, and oil and gas fracturing. Depending on the industry, the grade requirements can be the concentration of SiO2, particle size or shape, as well as contaminants such as the heavy refractory minerals, clays, fines, and alkali metals. With the ever declining mineral feed grade, processors continue to face challenges making the industry specific concentrate grade. As such, it becomes more important to tailor make the processing reagents to fit the mineral, processing conditions, and desired quality specification. This paper focuses on the application of novel collectors towards the beneficiation of sand for each of the major industrial silica applications. INTRODUCTIONQuartz is a mineral composed of a framework of silicon and oxygen atoms. It is the second most abundant mineral in the Earth’s continental crust. There are many species of quartz, which are defined by the particle size, shape, and color. Silica sand is one of those species, which is the byproduct of the physical or chemical breakdown of quartz containing rocks or crystals. Geologist define silica sand as a silica mineral with a particle size between 0.05 and 2 mm in diameter (Zdunczyk, 2001). Silica sand has significant value to society in recreation (beach sand and toy boxes), construction aggregate (concretes and asphalt), industry (iron & steel casting, fracturing proppants, and glass), as well as specialty products such as semiconductors or silicon wafers used in electronics.The aggregate business is the dominant consumer of silica sand products. Conversely, glass making, foundries (casting material), abrasives, and fracturing proppants are the dominant applications for industrial silica sand. Not much beneficiation is required for sand products going into the construction industry, other than sizing and scrubbing to remove clay. However, the industrial silica sand applications are dependent on particle size, shape, and degree of contaminants, which sets the market value (table 1). Therefore, as the more specialty products are produced, more sophisticated techniques and chemistry need to be applied to ensure the appropriate quality is met."

Jan 1, 2018

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By A. Burduk

The traditional approach to managing information flow between a mine underground and overground, applied in copper mines of KGHM Polska Miedz S.A., is mostly based on exchanging spoken information using the mine telephone network and printed documentation. This way of information flow significantly influences effective use of time of a shift foreman employed at a mining division. In order to minimise multiplication of significant information generated as paper documentation, a concept of an IT system module to input basic data concerning operation of the mining division was developed. The idea is based on computer software that permits inputting data in the underground and their immediate sending to the overground. The above-mentioned solution will permit significant reduction of administrative work time that each foreman has to do on each shift. The time saved on filling forms and communication will permit the foreman and the other workers involved in information flow to spend more time for execution of their basic duties. In the case of the supervision employees working in the overground, the IT system will allow all the interested persons to be informed directly, with no necessity to transfer the information on the situation in the given mining division by turns from one to another. On the other hand, saving time on administrative works will permit the foreman employed in the underground executing more detailed inspection of workplaces in his subordinate mine division. Thus, availability of the foreman for the mining division operation will be improved. KEYWORDS

Aug 1, 2013

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962

By H. F. Yancy

PooR results in coal washing and in ore concentration are sometimes attributed to the shape of the particles in the feed. It is well known that the shape of a particle influences its rate of fall in water. This is evidenced by the value of the constant C in the Rittinger equation for the velocity V of settling in water, V = C-D(d- z ), where C has the following values: 2.73 for roundish grains, 2.37 for long grains and 1.92 for flat grains. This report, which is based upon data obtained during the course of coal-washing investigations conducted by the U. S. Bureau of Mines in cooperation with the College of Mines of the University of Washington, gives the results of a method or procedure of screening in which the particles are separated into three shapes and shows the deportment of these shapes when coal is treated on a coal-washing table. The method consisted in first screening the coal with Tyler standard square-hole sieves, followed by screening tests of each of these products with screens of rectangular opening. For this purpose Tyler "Ton-Cap" screens were used; each square-hole product was subsequently sized with two Ton-Cap sieves so selected that their shortest dimensions were approximately 75 and 50 per cent., respectively, of the opening of the square-mesh sieves. For example: A product which is through 8 mesh (0.093 in.) and on 10 mesh (0.065 in.) is screened on slotted sieves which have openings 75 and 50 per cent. of the 0.065-in. opening in one direction and an opening of not less than 0.065 in. in the other direction. For convenience in discussion, the particles retained on the first slotted screen are termed "cubical"; those retained on the second slotted screen are termed "prismatic" and those passing the second screen are called "flat." (See Fig. 1.) The square-mesh screens separate particles according to two dimensions, length and breadth; the slotted screens divide them further according to the third dimension, or thickness. Prismatic particles have a mass of about two-thirds, and flat particles of about one-half, that of cubical particles of the same square-mesh size. The screen-

Jan 1, 1931

By James Westfield

Following is a brief history of Bureau of Mines Division of Coal-Mine Inspection activities that have favorably effected health and safety and reduced Injuries at coal mines: The Federal cline Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines for the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consulting with representatives of management and mine workers, and was incorporated in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, betweeen the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines considered imminently dangerous, but authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1962

Hindustan Zinc Limited has successfully installed an In-Stream Analysis and Process Control System in the flotation section of the Balaria Lead-Zinc concentrator at Zawar Mines. The system comprises In-Stream Analysis to continuously monitor lead and zinc levels in feed, concentrates and tailings streams, field instrumentation for reagent distribution and flotation cell level control linked to a central Distributed Control System for supervisory control functions. An intensive training scheme was conducted by the system supplier for concentrator metallurgical and instrumentation engineers. Since commissioning of the system in April 1989, Hindustan Zinc has enjoyed the benefits of improved lead, zinc and silver recoveries, improved concentrate grade control and reduced reagent costs.

Jan 1, 1991

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

The quality of the external water source for a mineral processing plant may influence the extent to which the environmentally desirable practice of recycling of water from plant products is possible. This is particularly likely for froth flotation plants where the chemical quality of the water may affect the plantÆs performance. The quality of the external water source or the recycled water can be improved by a water treatment step, and in turn the extent of recycling which can be tolerated is able to be influenced. The quality of the external water can range from very high quality, soft water derived from melting snow, to poor quality, hard water (high levels of dissolved calcium and magnesium) from underground aquifers, and to even lower quality sea water (very high levels of dissolved species including sodium chloride). It can be noted that some underground water is more saline than ocean water as well as containing high levels of dissolved calcium and magnesium. Occasionally, a different source of water is utilised in the wet and the dry seasons. Increasingly, sewage water from cities is becoming a potential external water source with sustainability implications. If the initial quality of the external water is high, the scope for recycling of water from all the products is maximised. Such reuse or recycling of water from the products allows chemical species from oxidation of the ore and from other inputs to the process such as reagents to increase in concentration in the water returned to the plant. Such accumulation of species can have negative effects on the performance of a process such as froth flotation but instances of positive effects exist. Some reagents which are used in flotation plants such as lime or sodium carbonate also happen to be commonly used for independent water treatment plants. Hence, the flotation process may inadvertently provide some aspects of water processing. Where the quality of the water in the feed to a mineral processing plant (external water plus recycled water) is not an issue, more powerful solid-liquid separation processes can be considered to maximise the removal of water from the products and its reuse. Such processes may also have complementary benefits in a sustainable mineral industry by, for example, producing a tailing stream with a higher per cent solid value which is more suitable for safe storage on the surface or underground. This paper documents findings on the effect of water quality on the flotation process. It also considers current directions of change in the need for increased removal of water from plant products. It then considers the implications of these trends for maximisation of water recycling by such operations.

Jan 1, 2003

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state&apos;s total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society&apos;s constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

The National Personal Protective Technology Laboratory (NPPTL) of the National Institute for Occupational Safety and Health (NIOSH) has undertaken a collaborative study with the Mine Safety and Health Administration (MSHA) to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), withstand the underground coal mining environment with regard to both physical damage and aging. Apparatus tested included the CSE SR-100, the Draeger OXY-K Plus, the MSA Life-Saver 60, and the Ocenco EBA 6.5 and M-20. This report presents findings regarding laboratory-tested SCSRs in the tenth phase of testing, from July 2004 to March 2006. The SCSRs were tested on a breathing and metabolic simulator and on a human subject walking on a treadmill. The tests performed in this study are not the tests used for certification (Title 42 of the Code of Federal Regulations, Part 84). The tests performed in this study continue until the apparatus are empty to enable comparison of new versus deployed apparatus. The method for obtaining deployed SCSRs for this evaluation was not a random selection from the deployed population of SCSRs. We sought older apparatus with visible environmental impact rather than newer apparatus, and we attempted to sample a wide range of deployment modes. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. This report is the last of 10 report phases begun in 1982. Previous reports describe phases 1 through 9 [Kyriazi et al. 1986; Kyriazi and Shubilla 1992, 1994, 1996, 2000, 2002, 2004, 2006] A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the applicability of the results. The results of these studies suggest that the large majority of SCSRs that pass their inspection criteria can be relied upon to provide a safe level of life support for mine escape purposes. However, the storage and handling in the mining environment seems to have caused performance degradation in some of the apparatus. In this phase, phase 10, we found some CSE SR-100s (93 tested) that exhibited high CO2 levels, stuck-together breathing hoses, starter-O2 failure, breathing hose punctures and tears, high breathing pressures, and loose particulates in the breathing hose. The loose particulates caused coughing in human-subject tests. One MSA Life-Saver 60 (20 tested) in this phase had a stuck-open relief valve. One Ocenco EBA 6.5 (50 tested) had an unattached O2 supply hose. An unexplained phenomenon occurred with two Ocenco M-20s (20 tested): low O2 flow rates preventing their successful use. Almost all of the failures noted involved units that failed their inspection criteria.

Jan 6, 2008

By John G. Groppo, Bonnie Webb-Groppo

INTRODUCTION The first portion of this chapter is concerned primarily with the contamination aspects of fine coal cleaning that include both the solids and water discharged as waste products after coal preparation. Topics include characteristics of the water and solids, changes that occur to both of these phases during use and after impoundment, as well as the impact that these changes have on unit operations and the environment. Attention is also given to the formation of acid mine drainage and treatment options that may facilitate reuse of the water. The second part of the chapter analyzes the problem of air contaminants from coal preparation plants including analysis of air pollutants and control methods. An overview of air quality regulations is also presented; most provisions have little or no applicability to coal preparation plant operation but are presented to provide an understanding of end-user constraints. The final part of the chapter emphasizes the long-range problem of refuse disposal and control. An overview of characterization, maintenance, and control of the refuse area is presented, as well as design guidelines. A brief review of stability analysis procedures is also included. PREPARATION PLANT WATER Characteristics of Makeup Water for Coal Preparation There are few specific rules governing the quality of makeup water used in coal preparation processes.&apos;" It is generally accepted, however, that the solid matter content should be less than 5%. The solids concentration in plant makeup water typically varies between 0.25 to 0.9 lb per gal (30 to 110 g/L) and may reach concentrations as high as 1.7 lb per gal (200 g/L). The water used in coal preparation is usually obtained from one or more of the following sources: public supplies, rivers and streams, canals, mine water, and wells. In most cases, water is obtained at the lowest cost including any necessary treatment. A major portion of the recirculated water is clarified by thickeners and settling ponds to remove fine coal and clay particles. Sufficient water is generally available to meet the needs of coal preparation in most areas. It has been estimated that approximately 65 to 70% of the makeup water used in a coal preparation plant comes from surface sources. It is important to note that a variety of substances are commonly found in natural water supplies, whatever the available source may be (Table 11-1). Excessive concentrations of some of those substances can have an affect on plant performance; the effect of specific contaminants on unit operations will be discussed

Jan 1, 1991