Search Documents

By Z. Zitron

In 1978 the South African Coal Processing Society (SACPS), together with the Institute for Energy Studies of the Rand Afrikaans University, ran a school on coal processing. This was judged by both the organizers and the participants to have been extremely successful. As a result, it was decided to hold a second coal school in 1980. NIM reports Report no. 1958 A mineralogical investigation of sulphide-bearing chromitite from the Loskop Dam ar..a.(10th Feb., 1978; reissued 1st De!)., 1980). Report no. 2067 List of unrestricted NI M publications issued from 1966 to 1980. Report no. 2076 Wet high-intensity magnetic separation. Laboratory tests conducted in 1978 and 1979. Report no. 2083 The determination, by anodic-stripping voltammetry, of zinc and lead in six NIMROC reference samples. Report no. 2086 An automatic sampling probe for use in the carbon-I npulp process.

Jan 1, 1981

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By M. A. EI Zeky, A. E. El-Nikbaily, M. A. Shahin

"Possible mechanisms of microsilica dust formation and factors affecting its quantity have been discussed. General mathematical models to predict the dust quantity based on electrical and coke consumptions, and flue gas temperature as functions of silicon recovery in the process and silicon content of the alloy have been established. It has also been shown that the flue gas temperature can be used as an additional process control parameter. Comments are made on the effect of the dust formation on the whole process economics and it is pointed out that the formed microsilica dust is a valuable by-product and not an industrial waste. INTRODUCTIONFerrosilicon is produced in electric arc furnaces with submerged electrodes. The charge mixture consist s mainly of quartzite, coke as the reducing agent and iron chips. The products are ferro silicon and carbon monoxide, various other volatile materials, water vapour and silicon monoxide gas. Carbon monoxide and silicon monoxide oxidize at the charge surface when mixed with air entering through the furnace hood openings. The off-gas contains a considerable amount of dust, which is mainly very fine particles of silica formed as a result of oxidation. The emission of dust containing gases to the atmosphere causes serious pollution problems to the environment. Therefore, the control of the formation of the dust, preventing it from escaping to the atmosphere, and dealing with this very fine dust collected from the flue gases represent important technological and economical parameters in the ferrosilicon production industry.This paper is concerned with the relations between the quantity of formed micro silica dust, as a function of both silicon recovery and silicon content in the alloy, and various other technological parameters; and their possible effects on the energy consumption and economics of the whole process."

Jan 1, 1989

By Steve Stuart

Deep-sea mineral SMS deposits present some of the world’s most challenging conditions for drilling equipment. As robotic seabed drilling services mature so too the ways that clients engage with service providers to maximise their data requirements. This presentation reviews key considerations for planning and executing a successful seabeddrilling program in variable mineralised deposits. Some of the means of collaboration between robotic seabed drilling contractors and those hiring their services are explored; where improved efficiencies and recoveries over the period of a drilling programme could be achieved. Potentially new technology or methodology can be looked at to further improve these approaches.

Sep 1, 2014

The Physical Basis of Non-Random Breakage in an Iron-Oxide Ore Hosted Copper Gold Ore

Sep 13, 2010

By G. H. Friedrich

The distribution of mercury in soils, rocks, and ore was studied in three areas of the Pachuca-Real del Monte District: (1) An area north of the town of Pachuca where ore veins have been found at or near the surface. The mercury content of soil samples taken near the vein zones is far above the background value. The highest value was 1900 ppb (parts per billion) mercury in a soil sample above Veta Vizcaina; the background is about 50 ppb Hg. (2) In the area north of the town of Real del Monte where only a few of the veins are known to crop-out. Regardless of exposure, soils collected over veins show anomalous mercury values ranging from 250 ppb to 1900 ppb. (3) In an area south of the town of Real del Monte. Here, although vein outcrops are lacking, mineralization is known at a depth of about 120 m. All soil samples taken at 50 m. intervals along an east-west traverse contain anomalous amounts of mercury, with peaks corresponding with the known location of the veins.

Jan 1, 1965

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By A. Policard

The question, of the pathogenesis of pneumokoniosis is very important not only from the social and economic points of view but also from the purely biological. The study of the pathogenesis of the disease leads to fascinating problems of cytology and cytochemistry. Two problems present themselves for examination from an analytical and critical point of view: 1. The first reactions of the alveolar walls to inhaled dusts. 2. The precise nature of the action of mineral dusts.

Jan 1, 1947

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By K. Anderson

There is a credible, cogent, and responsible argument that mining can be part of a sustainable future in countries with freely elected governments, transparent and enforceable laws, a closure plan with an adequate bond, and a small handful of other measures. This perspective, built largely upon the understanding of mining as a temporary use of the land, is coupled with a growing understanding of economic diversification as a tool to level out the ‘bust’ side of the boom and bust cycle. There are verifiable signs of progress that the sector has, at least in some venues, begun to embrace this view of ‘sustainability’ both in philosophy and practice. While laudable, there remains a conundrum not yet fully explored. It is conceivable that companies can fulfill all legal requirements, practice corporate responsibility in its broadest and most liberal interpretation, and yet leave behind, after the gates are closed and the lights turned off, a situation which is not only unsustainable, but far worse off than before mining started. Having observed this outcome, repeatedly, some critics have concluded that all mining should be stopped. Others recommend that it be vastly curtailed until regulatory regimes are re-vamped, communities fully empowered, and companies brought to heel. Yet others, including many within the industry, are looking to hold back this dark prospect with peer pressure, branding and competition for good will. In this paper, I propose to focus on this discontinuity, that gap wherein the chain of logic breaks and reasonable policies, reason-able choices, reasonable actions, may fail to deliver expected results. I suggest that any meaningful definition of post-closure sustainability must include the concept of human welfare, and increasingly, human security, over and above meeting the requirements of law, beyond retaining shareholder value and reputation, beyond discussions of subsequent land use and diversified employment. I suggest that self-determination, that ability of a people to hold for themselves the vision of their own future, and to have a sense of their power to implement it, may be both the most difficult and the single most important determinant of long-term sustainability in a community. The particulars will vary; a Canadian junior or an Australian multinational, a highly regulated state in the American west or a ‘failing state’ in Africa’s west, gold or sand and gravel. But the recommendation is the same: this must be a collective endeavor, a shared responsibility involving some combination of government, companies, communities, local and international NGOs (non-governmental organizations), each contributing in the ways most able.

Jan 1, 2004

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By Rimas Pakalnis, Catherine A. Dreesbach, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash's trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 micro strain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

Jan 10, 2000

Underground mining in the West Moreton coal field started in the 1870's. Subsidence related to coal mining activities is an ongoing problem facing planners and developers in the Ipswich area in South Eastern Queensland. The history of coal mining in the area over the last 110 years has left the legacy of periodic surface instability in several areas. In general, modern engineering analysis with current mining methods combine to create predicatable analysis of surface stability and movement. Where old workings using several variations of the bord and pillar system are affected by current activity, the predictibility of the surface movement is greatly reduced. Geological complexities further complicate the analysis. Mining and the related dewatering affects the stresses on pillars in old workings. This is caused by reducing buoyancy effects caused by changes in the water levels in old workings. Of particular relevance is the depth of workings and strength of the coal and overburden. The type of subsidence affecting the surface can range from localised pillar failure, to roof failure and potholing and the likelihood of the particular form of subsidence can be assessed from studying the workings in relation to the stratigraphy and structure of the coal measure Formations.

Jan 1, 1988

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities during 2017 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY) and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2017 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize budget estimates for worldwide exploration activities in 2017 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup metals (PGMs) and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2017 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities."

Jan 5, 2018

By Muller GP, van Deventer JSJ

A mineralogical analysis has shown that in the Hartebeesfontein ore studied, uranium is associated mainly with uraninite, sulphides such as pyrite and to a lesser degree carbonaceous material such as thucolite. Little could be learned from the literature regarding the mechanism of flotation of these uranium-bearing minerals. A wide variety of reagents were used so that conditions enhancing the flotation of either the sulphides, carbonaceous material, oxides like uraninite, or combinations thereof, were created. As could be expected, the xanthate based floats gave-better selective recovery of sulphides than oleic acid. A substantial fraction of the uranium is associated with pyrite, so that addition of oleic acid to a xanthate float did not enhance the recovery or grade of uranium. After a pre-leach with sulphuric acid in which the pH and Eh were controlled so as to destroy the uraninite, higher uranium recoveries were obtained for the combined float (xanthate, DTP and oleic) and the DTP float. This was most evident when iron was added before flotation. Roasting, which destroyed the sulphides and thucolite, caused a significant decrease in uranium recoveries. The uranium liberated in this way was obviously not flotable in the same way as the uranium liberated from uraninite. A small amount of iron (2 kg/t) added before milling resulted in slightly higher grades and recoveries of sulphur for xanthate based floats. Higher iron additions had a detrimental effect on sulphur recoveries. Even in the case of oleic acid the addition of small amounts of iron had a positive effect on the recovery of sulphur and uranium.

Jan 1, 1993

By J. Lee

A monolithic caisson is one of the major structural components commonly used in the construction of docks, breakwaters, and container terminal quay walls. Since the structure of monolithic caissons is typical and somewhat simple, its design process is also typical and repetitive, but still time consuming. To reduce the total time and enhance productivity, we developed a parametric model in Revit to automatically generate a 3D model of a monolithic caisson. It is designed to generate the Revit model of a caisson with concrete body and reinforcing bars. The size of caisson, the number of reinforcing bars, and the space between reinforcing bars are automatically changed when users update parameters. This paper presents how we developed this parametric family in Revit for monolithic caisson design and how it would enhance its design process.

Aug 1, 2013

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

Dry weather since the third week in January has set back any prospects for an early increase in hydroelectric power in the Pacific Northwest, according to The Bonneville Power Administration. The 25% cutback made in July probably will not be restored in March or April. Noranda Aluminum, Inc., increased its price for 99.5% aluminum ingot from 66 cents to 70 cents per pound effective March 1, 1980. Revere Copper & Brass, Inc., also -increased its price for primary aluminum from 66.0 cents to 70.0 cents per pound effective February 1. Kaiser Aluminum & Chemical Corp. raised its international price for 99.5% primary aluminum from 72.6 cents to 82.6 cents per pound, c. i. f., effective February 26 on new orders and on shipments from March 15.

Jan 1, 1980

By Tim Neil, O&apos

Introduction Compania de Carbones de Chile (Cocar SA) has brought into production Chile's first large-scale, open-pit coal mine, located in the Magellan Province. The US $65 million project includes a 1.1-Mt/a (1.2-million stpy) subbituminous steam coal mine and a mechanized bulk loading marine terminal with water depth sufficient to receive 60 kt (66,000 st) Panamax vessels. The loading terminal will be one of the largest in Chile. The Pecket coal project is expected to save Chile about $40 million in energy production costs and a further $100 million in oil imports, or about 25% of the country's oil import costs. Pecket coal will generate electricity for Codelco and will also supply general electricity needs for northern Chile. The Pecket coalfield is located on the Brunswick Peninsula, about 30 km (19 miles) northeast of Punta Arenas, the provincial capital, as shown in Fig. 1. Pecket is part of a large, coal-bearing basin. It extends from Punta Arenas 250 km (155 miles) north to Puerto Natales and across the border into the Rio Turbio coalfield in Argentina. A fleet of large and small O&K hydraulic shovels and backhoes is used to dig and load overburden and coal into mining trucks while O&K graders maintain the haul roads in and around the pit. Coal occurrence in the Magellan area of Chile has long been

Jan 1, 1988