Search Documents

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By R. B. McIntosh, S Ramanchuk

A brief description is given of the process used by Sherritt Gordon Mines Limited to recover cobalt metal from nickel-cobalt sulphides. A description of the equipment with the operating conditions is presented with an evaluation of the corrosion test results for various stainless steels and other acid resistant materials for the part of the process involving the sulphuric acid leaching of nickel-cobalt sulphide slurry under air pressure. SINCE 1954 the Sherritt Gordon ammonia leach process has been used at Fort Saskatchewan to recover nickel metal, copper sulphides and cobalt-nickel sulphides from nickel concentrate produced at Lynn Lake, Manitoba. 'To develop a process for recovering cobalt and nickel from the cobalt-nickel sulphides, studies were carried out in the Sherritt Gordon laboratory and pilot plant and, late in 1957, continuous acid leaching of sulphides was started in the refinery. In September 1958 the present equipment

Jan 1, 1961

By K Byrne, W. Hawker

The average grade of copper concentrate is steadily declining, forcing the industry to turn to lower grade and metallurgically challenging orebodies. When faced with a low grade, challenging ore, mining companies are often forced to choose between high recovery at low grade or low recovery at high grade. Hydrometallurgical processing of copper concentrates using metathesis reactions, which replace iron with copper in copper-iron sulphide minerals and increase the copper to sulphur ratio in copper sulphide minerals, provide an opportunity to upgrade copper concentrates and potentially allow high copper recovery for a high grade concentrate. Factors such as concentrate mineralogy, reaction time and temperature, and the concentrations of copper, chloride and acid in solution are reported to affect the reaction extent and mineral phases formed by metathesis. In this paper, a copper concentrate has been studied over a wide range of conditions to investigate the influence of these key parameters on the extent of copper metathesis reactions and product phases formed. Solution and solid phases are assayed with the main mineral phases identified by Quantitative X-Ray Diffraction. INTRODUCTION The minerals present in copper deposits determine the prospective processing options either: pyrometallurgical or hydrometallurgical. For copper oxide ores, copper is typically present as oxides, carbonate, chlorides, silicates and sulphates. These minerals are readily solubilised in acid and are usually treated through hydrometallurgical processes. The typical process route for copper oxides is to leach copper into aqueous solution, purify and upgrade the solution phase through solvent extraction and then recover copper as metal by electrowinning (Davenport, King, Schlesinger, & Biswas, 2002). Copper sulphide deposits may contain a multitude of copper bearing minerals, including chalcopyrite, bornite, enargite, covellite, digenite and chalcocite. The copper ore grade and treatment options are affected by the mineral type and distribution. Sulphide ores are typically treated through comminution and mineral flotation to form concentrates, followed by pyrometallurgical smelting. Hydrometallurgy can also be used to process sulphides depending on the mineralogy and impurity levels (Davenport et al., 2002). The trend of decreasing copper grade with increasing impurity levels are common across the mining industry and pose future challenges to copper processing. This trend has prompted research into hydrometallurgical options for upgrading copper concentrates. One promising hydrometallurgical option is using metathesis reactions. Metathesis reactions, sometimes also called double replacement or displacement reactions, are chemical processes involving the exchange of bonds between two chemical compounds or species. In this case, the metathesis reactions involve copper in solution exchanging with cations in the solid sulphide concentrate. The driving force for copper sulphide metathesis is the relative affinity of the exchanging cation elements for sulphide. Based on sulphide precipitation diagrams, the expected order of affinity for sulphide should be Hg2+ > Ag+ > Cu+ > Cu2+ > Bi3+ > Cd2+ > Pb2+ > Sn2+ > Zn2+ > Co2+ > Ni2+ > Fe2+ > Mn2+ (Monhemius, 1977). Hence, copper metathesis reactions are capable of increasing copper content and removing impurities such as iron, nickel, zinc and lead from copper concentrates.

Jan 1, 2019

By J. E. Flinn, E. R. Gilbert

Recently, Green reported some high-temperature, 0.60 to 0.89 T3, creep results on unalloyed tantalum. From his study he determined an activation energy of 114 kcal per mole for steady-state creep using the T, differential-temperature method25 for testing. He accounted for the difference between this value and 110 kcal per mole for self-diffusion by the temperature dependence of the elastic modulus, 4 kcal per mole. This reported activation energy is in apparent disagreement with that which can be determined from Green's isothermal data, which we have plotted as log creep rate vs 1/T in Fig. 15. From this figure, it appears that there are two activation energies of -185 kcal per mole at the higher temperatures and -75 kcal per mole at the lower temperatures. It is not obvious that the data can be fitted to a straight line corresponding to an activation energy of 114 kcal per mole. One is led to two possible conclusions regarding Green's study: there are two discrete processes controlling the creep rate from 0.60 to 0.89 Tm or the apparent activation energy is not discrete but continuously increases with increasing temperature. The former speculation would be in closer agreement with the high-temperature creep behavior of tungsten.28 The apparent disagreement between the activation energies determined by the AT and isothermal methods certainly suggests that further study on the high-temperature creep of tantalum is needed.

Jan 1, 1967

By P. Bandopadhyay, T. C. Rao

Geologically the Indian coals belong to Gondwana formations. Being of drift origin, these coals contain high percentage of mineral matter distributed in finely disseminated form. Indian coal-preparation plants process prime coking and medium coking coals for use in steel plants. Limited resources of good quality coking coals (Table 1) could not keep pace with the rapid developments of the iron and steel industry in India. This resulted in the introduction of coal-preparation technology and the establishment of washeries in India in the last 30 years or so. The first four washeries were set up during the early fifties at West-Bokaro, Jamadoba, Lodna and Kargali. Next came the first non-coking coal washery at Nowrozabad set up by the Associated Cement Company. In 1961, following the recommendation of Central Coal Washeries Committee (1953-54), Hindustan Steel Ltd. had set up five central washeries at appropriate locations, viz Durgapur, Dugda (2 washeries), Patherdih and Bhojudih, so that the raw coal feed having similar washability characteristics can conveniently come from a number of collieries to a particular washery. Subsequently, to meet the increasing demand of metallurgical coal by steel plants, two more central washeries (at Durgapur and Chasnala) and three pit-head washeries (at Kathara, Swang and Gidi) were installed by 1970. The prime objective of washing Indian coking coal is essentially to reduce the ash content. All the washeries in India, taken together have an installed capacity of about 26 million tons of raw coal input per annum. Details of these washeries in respect of their annual capacity, main washing systems adopted and the nature and size of the products are given in Table 2. It can be observed from this table that (1) bulk of the coal is processed in units like jigs HM baths and HM cyclones; (2) only two of the washeries have cleaning circuits for treatment of fines.

Jan 1, 1980

By William H. Snyer, Hank Cox

A high explosive device using Linear Shaped Charge (LSC) (to rapidly cut vent and drain openings in a rail tank car) is described. In the event of damage to a tank car loaded with a pressurized flammable fluid, it may sometimes be necessary to perform controlled on-site vent, drain and burn operations. Existing techniques required refinement to achieve the desired safety and procedural reliability for use in emergency situations.

Jan 1, 1994

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By P. C. A. Maia, J Alexandre, F. A. J. Saboya, A. R. G. Azevedo, G. C. Xavier

"This work shows the characterization of clay and the granite waste by-product from the sawing process of the granitic blocks, used as raw material for brick ceramic. Besides, shows the degradation of the ceramic material obtained with different by-product contents in the waste after lab test degradation, is investigated. The clay is obtained from mine use areas of ceramic industry in Campos-RI and the waste is originating from of the area of Cachoeiro-ES, an important center of decorative stone in Brazil. The mixes were made by the addition of 0% up to 10% of the waste in the raw material. After drying and firing up to 900°C, obtained prismatic pieces were considered intact. Physico-mechanical properties were obtained from wet and drying tests in laboratory considering 50 and 150 cycles. The results showed that the use of powder byproduct has a considerably influence on the weathering and strength of the material.IntroductionThe ornamental rocks and coating defines the most promising areas of business in the mineral sector [l]. In this context, the Espirito Santo appears as the main Brazilian state in production and export of ornamental rocks, representing 47% of national production [2] which in tum is one of the economic sectors most representative of this State, due of its transport logistics and port vocation that facilitates the export of such products.It is estimated that the state of Espirito Santo there are approximately 1,200 companies dedicated to the activities of ornamental rock by providing 20,000 direct jobs [ 1]. These mobilize support activities, such as companies that provide machinery, equipment and supplies for industries, including service providers for maintenance.However, the production of rocks produces about 15,000 tons of granite waste/month [3] only in the municipality of Cachoeiro ltapemirim-ES. This is justified by the presence of more than 500 extraction industries, cutting and processing of stone, with about 900 looms, waste generators.According to [4], there is great potential for the use of granite waste in red ceramics introduced for the manufacture of bricks, blocks structural ceramics. and other ceramic products, especially when evaluated on exposure to weathering."

Jan 1, 2014

This paper presents an overview of the strategy adopted to bring the Ballymoney opencut lignite deposit to an advanced stage of mine design and confidence. Certain aspects of the project differentiate it from the normal Australian experience. These include the thick overlying glacial drift, the proximity to established infrastructure and the wide fluctua- tions in annual lignite demand. The incorporation of these factors in the mine plan are discussed. The deposit area is located near the town of Ballymoney, in Northern Ireland. In July 1986, after winning an internationally competitive tender, Meekatharra Minerals Ltd commenced an exploration programme designed to delineate reserves to supply a 450 MW power station. In less than eighteen months, a complete evaluation was undertaken and a price submitted in December 1987 to the relevant authorities for the supply of lignite. Subsequently, UK government consultants and significant inter- national banks have endorsed the findings. The mining study commenced with the evaluation of various develop- ment strategies, followed by selection of the most viable mining method and equipment. The equipment selected will mine four million tonnes of lignite and eleven million cubic metres of waste each year. In year 15, the waste removal requirement increases to almost seventeen million cubic metres. This results in an average strip ratio over the mine life of three cubic metres of waste per tonne of lignite. The quality of the product delivered to the run of mine conveyor transfer point, based on maximum resource recovery, will include heat content of 8813 kJ/kg (3789 Btu/Ib), ash content of 28% and moisture content of 40%.

Jan 1, 1989

By E. L. Kapfer

A preliminary description is made of the field of automation and optimization of the oxygen blast furnace process. The concept of static and dynamic process control is illustrated. After a short general description of all factors concerning the optimization of this process, a learning system is derived which gives better results than models previously used. This learning or self-adaptive control system uses statistical methods with exponential aging of process data and requires derivation of multi-variable functions of the process for which measurements can be made available. The practical application of this new procedure and of additional measuring instruments are discussed, and results obtained in plants using the adaptive control system are described. A survey of European steel plant automation using the Siemens technique is presented.

Jan 1, 1969

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By Giancarlo Obando Díaz

Ante la irregular distribución de la riqueza y consecuente subdesarrollo socioeconómico de algunos centros poblados del Perú, se estableció que el uso del gas como fuente de energía renovable puede satisfacer la demanda de los sectores desfavorecidos con la disponibilidad comercial. En ese sentido, el presente texto señala las herramientas posiblemente utilizadas por empresas mineras para aprovechar el potencial energético del biogas y la calidad fertilizante del efluente en el desarrollo socioeconómico de comunidades rurales aledañas a sus centros de operaciones.

Sep 14, 2009

By Harry Tufft

FOR many years the treatment of mine timbers with preservatives was confined to a few pioneer plants in the United States, and it is only in the past few years that the practice has grown appreciably. In a field study of the mine timber situation in Illinois, Pennsylvania, and further study of the situation in the country as a whole, I found that most mine operators did not keep records on mine timber that would afford the necessary data for determining the possible savings from preservative treatment. Some primary questions the mining engineer should be able to answer before making his decision on preservative treatment. for a particular mine are: (1) Quantity and cost of timber going into permanent workings annually; (2) quantity and cost of annual replacements due to decay; (3) life of untreated timber in different places; (4) desired life of timber. With the necessary facts in hand, he can then con-fidently select a method of treatment and preservative that is best suited to his needs. In former years when timber was cheap and an abundant supply could be had close at hand, as was the case in the majority of mining regions, the mine op-erator did not concern himself much except to see that enough was supplied to keep the workings safe. The cost figure for timber and labor, distributed to cost per ton of ore, was all the bookkeeping necessary. With present costs of timber, labor, and increasing length of haul to the mine, many operators are paying closer attention to timbering costs and studying them in. more detail. Some of the larger and more progressive opera-tions now keep detailed' figures that give information on all phases of their timber problems. However, at the majority of mines the data available do not permit such analysis. Checks as to where the different con-signments are placed, the date of setting, and the period

Jan 6, 1927

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By G. A. Vissac

In the presentation which follows, wash-ability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. Float-and-sink Tests For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve"—a somewhat misleading term—will be considered; Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. New Form of Graphic Presentation The resemblance of the recovery curve ill Fig. 1, or, for that matter, the recovery curve obtained in common practice! to a Power curve is apparent. The general equation of such a curve is Y = axn, where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis! the recovery graph will be a straight line, using the same variables as in Fig. I; namely, the ash con-

Jan 1, 1942

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

By L. Van Wyk, J. Fernandez, J. Suarez, L. J. Diaz, A. Uria, D. Breeuwer

"Ventilation is an essential component of any underground mine, playing a vital role in ensuring the health and safety of workers, and a mine’s continuous operation. At a time when mining companies are increasingly having to move to deeper underground operations in pursuit of high-grade ore-bodies, the search is on for more efficient ventilation systems that will allow mining to be carried out at even deeper levels whilst ensuring the protection of workers and the maximisation of productivity through temperature management and the lowering of energy costs. Mining companies today are looking for innovative ways to deliver new technologies and procedures to enhance their mine’s profitability. Energy consumption by mine ventilation systems is higher than ever due to stringent specifications of underground equipment (primarily combustion engine emissions), air quality standards and mining at deeper levels which all require more powerful ventilation systems. With energy costs associated with operating ventilation systems being a mine’s second-highest cost of production after labour, finding the optimal ventilation solution is critical to a mine’s performance. Proper fan design remains a major factor in reducing capital expenditures (CAPEX) and operational expenditures (OPEX), which means that there are compelling reasons for making use of comprehensive factory testing at full power before fans are dispatched to site to simulate the mine’s current and future design requirements, and thus verify the fan’s effectiveness in ‘real’ conditions.INTRODUCTION A primary mine fan is considered the heartbeat of the entire mine ventilation system, drawing fresh air from the surface and providing a safe environment for miners. A ventilation system’s lack of performance often leads to a reduction in acceptable air quality levels for underground working operations and can potentially have an adverse impact on production rates."

Jan 1, 2019