Search Documents

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,' it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By Enrique Touceda

As in the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time.. A few years ago, about the only test made to ascertain the physical properties of the product, except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 1, 1922

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By Robert M. Keeney, Jay Lonergan

The electric smelting of manganese ore and the production of ferro-manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 11/4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese orc in the electric furnace during the war and in 1920 are listed in Table 1. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferromanganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the price of ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 1, 1922

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By R. S. Reed, D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, 111. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation mas rermoved. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow road-ings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through met washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic. and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main mas fabricated from riveted sheets led us to discard the idea of using Pitot tubes for. this service. The Venturi tube mas then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made. A plate with a sharp-edged orifice was eventually accepted as it possesses all the characteristics of a Venturi tube, requires less space, and

Jan 1, 1922

By Richard S. McCaffery

This paper considers certain aspects of the acid bessemer process, particularly in its relations to the duplex process—that combination in which the pig iron is first desiliconized and decarburized in acid bessemer converters and then dephosphorized in basic open-hearth furnaces. The acid bessemer process employs an acid-lined converter and produces an acid slag. The blow is usually thought to eliminate the silicon and manganese as oxides and then to burn off the carbon as carbon monoxide On account, however, of the relatively large amount of metallic iron present in the converter, compared with the relatively small amount of the impurities it is desired to oxidize, the first reaction in the converter probably is the formation of iron oxide, which dissolves in the bath and acts as an oxygen carrier for the silicon and carbon. As soon as iron oxide is dissolved throughout the bath, the oxidation of silicon commences; but in the early stages of the blow the mass law would indicate that iron oxide must form first, and this oxide probably increases up to some saturation point. The molten metal in the converter from the early stages of the blow right through to its completion remains basic, while the slag produced is siliceous. This fact is shown by the corrosion of the acid bottom and the tuyeres, which is greatest at the tuyere orifice where oxidation is most active and where there is the most iron oxide. Why does this acid bottom corrode? Because it is attacked by a base. The thought, therefore, suggests itself, why not. make the bottoms of basic or neutral material?' As the converter slag is acid, those parts of the converter coming in contact with the slag should be acid; but those parts of the converter that are in contact with the molten metal saturated with metallic oxides should be basic. or neutral. Bessemer operators have for some time tacitly admitted this condition, for the blast pressures have steadily increased with the object of keeping the metal in suspension, and so preventing bottom corrosion; if the molten metal were not basic, it would not attack an acid bottom. In addition, the tuyeres are bunched together at the middle of the bottom and a clear space is left around the outside of the bottom; if tuyeres are placed too near the side walls the

Jan 1, 1922

Jan 1, 1922

Joseph William Richards, was born in Oldbury, Worcestershire, England, on July 28, 1864, of English-Scotch parents, Joseph and Bridget (Harvey) Richards. In 1871, he came to this country with his parents. He attended the public schools of Philadelphia, Pa., where his father was a manufacturing metallurgist, and in 1882, graduated from the Central High School with the degree of A. B. The same year he entered Lehigh University, from which he received the degree of A. C. (Analytical Chemist) in 1886; M. S. in 1891, and Ph. D. in 1893. His connection with the university was continuous from 1887 until his death, and he therefore adds another to the list of names of men Prominent in the A. I. 11. E. who have helped to develop Lehigh University to the important position which it now occupies in mining and metallurgical education in respect of world-wide fame. It is fitting to recall in this connection that, Eckley B. Coxe, a fonnder of the A. I. M. E., four times its vice-president,, and president in 1878-79, was literally a pillar of the university for several years prior to his death; Thomas M. Drown, founder, vice-presi(lent, secretary for 11 years, honorary member, and president in 1897, was president of Lehigh University from 1895 to 1904; and Henry S. Drinker, founder, manager, vice-president, and honorary member, was president of the university from 1905 to 1920. Doctor Richards was no less active in both institutions. With the exception of the years 1886 to 1887, when he was superintendent of the Delaware Metal Refinery of Philadelphia, his professional life was devoted to the upbuilding of the metallurgical department of the university, in part through his continuous services as a member of the teaching staff, and in part through the international renown won for the department by his achievevements as author, investigator, expert and rerognizcd authority in metallurgy, especially the metallurgy of aluminum, metallurgical-chemical calculations, and electrometallurgy. He was assistant instructor in metallurgy and blowpiping in 1887; instructor, 1888-90; instructor in metallurgy, mineralogy and blowpiping, 1890-97; assistant professor, 1897--1903; professor of metallurgy, 1903-1921. He died at his home in Bethlehem, Pa., on Oct. 12, 1921, of heart failure. To the A. I. M. E., for a continuous period of a dozen years, his services were equally loyal and effective. He was vice-president, 1910-11, and 1916-17; councilor, 1912; dirctor, 1913-15; chairman of the Iron and Steel Clommittee, 191-1-21; he was one of the framers of the Insti-

Jan 1, 1922

Dimitri Konstantinovitch Tschernoff, was horn in Petrograd, Russia, on Nov. 1, 1839, and died in Yalta (Crimea) in the south of Russia, on Jan. 2, 1921. He obtained his early education in the Russian Gymnasium, corresponding to the American high school, and in the Technologic Institute. On graduation from this Institute in 1858, he was engaged as a professor of geometry and algebra and later became a librarian and superintendent of the museum in the same Institute. He also attended lectures in the mathematical physics section at the Univrrsity of Petrograd from 1859 to 1862. In 1866, Professor Tschernoff left the Technologic Institute and entered the employ of the Obouchoff steel plant, founded in 1863 for the manufacture of guns. Here he did his most important work on the heat treatment of steel, its crystallization and metallography. In 1880, he left the Obouchoff plant and went to the south of European Russia, where he discovered and developed some rock-salt mines. This enterprise brought him a rather large fortune. In 1884, he returned to Petrograd and during the next four years held several prominent positions in government departments. In 1899, he became professor of metallurgy in the Michael Artillery Academy, and retained that position until the time of the Russian Revolution. In 1902, Professor Tschernoff was elected an honorary member of the American Institute of Mining and Metallurgical Engineers. In September, 1917, Professor Tschernoff was sponding his vacation, as usual, in the city of Yalta (Crimea) in the south of Russia, with his wife and one of his daughters. The revolution progressed so rapidly that they were unable to return to Petrograd, and were compelled to stay in Yalta without provision for the winter season. Suffering from hunger. and lack of sufficient clothing, and deprived of his books, Tschernoff nevertheless continued his studies and gave a number of lectures on steel at the Polytechnic Institute. At the same time he worked hard on some. mathematical problems. His health broke down through long-continued under-nourishment. His works in the metallurgical field are well known to the students of metallurgy; good abstracts of his most important papers were published in Revue de Metallurgie (1915, pp. 829-882) in commemoration of his 75th birthday.

Jan 1, 1922

Anders Richard Akerman entered the eternal rest on Feb. 23, 1922, after a long and distinguished career. All mining men in Sweden arc mourning him, because he was one of their greatest and a leader in the scientific metallurgy of the iron. He was born April 18, 1837, in Stockholm, where his father, Joachim Akerman, was a professor at the Technical University, but the greater part of his childhood was spent in Falun, where the family moved after his father was made principal of the mining academy. He was at first taught by a tutor, but in 1851 entered the high school in Vesteras and the University of Uppsala in 1855, from which he graduated as a mining engineer on Dec. 11, 1860. A week later, he entered the service of the Department of Commerce and entered the mining academy at Falun, from which he graduated Dec. 15, 1862. The following May, he was accepted as a student in the metallurgical section of "Jernkontoret" (the "Iron Institute") and on Oct. 22, 1864, he was made an assistant in the same section. Thus begun the cooperation with the Iron Institute which was to continue for so many years and to bear such rich fruit. He had, however, previously received two requests from the Iron Institute: One to assist Prof. V. Eggertz in the preliminary work of preparing a handbook on blast-furnace practice, the other to make a complete index of the proceedings of the Iron Institute ("Jernkontorets Annaler") volumes 1817-1864, which index was published in 1866. On Oct. 19, 1865, Akerman was requested by "Jernkontoret" to give during 1866, lectures in the metallurgy of iron at the mining academy of Falun, as Prof. V. Eggertz wished to devote his entire time to the study of assaying. This request was renewed Oct. 15, 1867, for the year 1868, and on April 17, 1869, he was made instructor in metallurgy and mining at the Technical University, to which institution the higher education in mining engineering was transferred at that time. Akerman thus entered his career as a teacher, which lasted until the end of 1891. On May 11, 1877, he was appointed assistant professor in metallurgy and mining; on Sept. 7, 1883, he was appointed acting professor in the same department; and two weeks later was appointed dean of the mining college. On May 21, 1874, he was instructed by the Crown to inspect the mining schools in Filipstad and Falun. As a teacher, Akerman was very popular and his lectures were excellent, in form as well

Jan 1, 1922

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Daniel M. MacNeil, Carle R. Hayward, Raymond L. Presbrey

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By H. J. French

At the request of a committee of the Engineering Division,' National Research Council, a study of the properties of boiler plate at various temperatures up to about 900' F. (482" C.) has been instigated. The following is a report of preliminary tests made on two grades of 1/2-in. plate and includes a description of the apparatus used in the determination of the proportional limit. Detailed reference to- the many published investigations in connection with the properties of steel at various temperatures will be omitted from this report. Suffice to state that results obtained for variation in tensile strength, elongation, and reduction in area with temperature are in substantial agreement with the effects now generally considered to be correct. Comparison of proportional limit values with results obtained by other investigators will be found in the conclusions. Materials Used The steels tested were $1/2-in. (12.7 mm.) open-hearth boiler plate of firebox and marine grades. The specified tensile strength and the analysis for each are shown in Table 1. In the manufacture of this material, a

Jan 1, 1922

By Howard Scott

The great advances made in mechanical engineering during recent years through the use of alloy steels, as illustrated by the development of the airplane and automobile, may be ascribed primarily to the application of nickel as an alloying element. The ternary system iron-carbon-nickel has a wide industrial application and forms, further, thefundamental basis of the even greater class of the widely used quarternary steels such as nickel-chromium, nickel-silicon, and nickel-vanadium. As is not uncommon with such cases of virile growth in an industry, the application of the alloy steel in a largely empirical manner has outstripped its scientific development so that a fertile field for metallographic research still remains. In this field, the basic nickel steels require first consideration and are the subject of the present investigation, which is offered as a preliminary to the study of the more complex alloys of industrial importance Of the principal tools of metallography—microscopic examination, determination of mechanical properties, and thermal analysis—the last has developed much more slowly in its application to industrial needs so that the situation often exists that heat treatment operations are based on empirically determined temperatures; that is, temperatures deterrnincd without regard to the actual transformation characteristics of the alloy. This situation is undesirable as there is no uniform standard for comparison of results. It is due, outside the usual difficulties involved in temperature measurements, to the pioneer character of much of the published work; to the lack of definiteness of the Ac, transformation,1 particularly in low-carbon steels; to the failure to define operating conditions completely; and to the paucity of information correlating thermal characteristics with results of heat treatment.

Jan 1, 1922